Configuration Guide for 6248 and 5548 and VNX 5500

Hi,
Need help here to configure the FCoE Uplink + Ethernet Uplink in Port channel
Following is the connectivity details from 6248, 5548 and VNX5500.
I have configured Port Channel in following way on Both Fabric Interconnect
After Configuring above things I am getting following Faults on Servers
For NetApp3240 ENM source pinning failed, I have allowed VLAN ID 21 in Uplink manager then too this Link state is  not showing UP and Same thing go for both FC_vHBA
Kinldy help me to configure the setup
-Amit

Below is the ouput for two commands "show run int port-channel membership" and "sh int port-channel "
===========================================================================
primary# sh run int po2 membership
!Command: show running-config interface port-channel2 membership
!Time: Wed Feb 25 07:55:31 2009
version 5.2(1)N1(1b)
interface port-channel2
  description ***Link to FI-A in R17***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  spanning-tree port type edge
  spanning-tree bpdufilter enable
interface Ethernet1/3
  description ***Link to FI-A in R17***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 2 mode active
interface Ethernet1/4
  description ***Link to FI-A in R17***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 2 mode active
interface Ethernet1/5
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 2 mode active
===========================================================================
primary# sh run int po3 membership
!Command: show running-config interface port-channel3 membership
!Time: Wed Feb 25 07:57:14 2009
version 5.2(1)N1(1b)
interface port-channel3
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  spanning-tree port type edge
  spanning-tree bpdufilter enable
interface Ethernet1/8
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 3 mode active
interface Ethernet1/9
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 3 mode active
interface Ethernet1/10
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 3 mode active
===========================================================================
primary# sh int po2
port-channel2 is up
  Hardware: Port-Channel, address: 002a.6a0a.4caa (bia 002a.6a0a.4caa)
  Description: ***Link to FI-A in R17***
  MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA
  Port mode is trunk
  full-duplex, 10 Gb/s
  Input flow-control is off, output flow-control is off
  Switchport monitor is off
  EtherType is 0x8100
  Members in this channel: Eth1/3, Eth1/4, Eth1/5
  Last clearing of "show interface" counters never
  30 seconds input rate 504 bits/sec, 0 packets/sec
  30 seconds output rate 2256 bits/sec, 0 packets/sec
  Load-Interval #2: 5 minute (300 seconds)
    input rate 456 bps, 0 pps; output rate 656 bps, 0 pps
  RX
    22208045 unicast packets  747374 multicast packets  27634234 broadcast packets
    50589653 input packets  49083144072 bytes
    21411174 jumbo packets  0 storm suppression bytes
    0 runts  0 giants  0 CRC  0 no buffer
    0 input error  0 short frame  0 overrun   0 underrun  0 ignored
    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
    0 input with dribble  0 input discard
    0 Rx pause
  TX
    2801196 unicast packets  353162904 multicast packets  549464 broadcast packets
    356513564 output packets  25978572978 bytes
    101325 jumbo packets
    0 output errors  0 collision  0 deferred  0 late collision
    0 lost carrier  0 no carrier  0 babble 0 output discard
    0 Tx pause
  35 interface resets
===========================================================================
primary# sh int po3
port-channel3 is up
  Hardware: Port-Channel, address: 002a.6a0a.4caf (bia 002a.6a0a.4caf)
  Description: ***Link to FI-B in R18***
  MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
  reliability 48052/255, txload 1/255, rxload 1/255
  Encapsulation ARPA
  Port mode is trunk
  full-duplex, 10 Gb/s
  Input flow-control is off, output flow-control is off
  Switchport monitor is off
  EtherType is 0x8100
  Members in this channel: Eth1/8, Eth1/9, Eth1/10
  Last clearing of "show interface" counters never
  30 seconds input rate 104 bits/sec, 0 packets/sec
  30 seconds output rate 1704 bits/sec, 0 packets/sec
  Load-Interval #2: 5 minute (300 seconds)
    input rate 448 bps, 0 pps; output rate 1.08 Kbps, 0 pps
  RX
    9070 unicast packets  288523 multicast packets  143322 broadcast packets
    440915 input packets  72677230 bytes
    7 jumbo packets  0 storm suppression bytes
    0 runts  0 giants  36 CRC  0 no buffer
    2161727821137838086 input error  0 short frame  0 overrun   0 underrun  0 ignored
    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
    0 input with dribble  0 input discard
    0 Rx pause
  TX
    62914 unicast packets  74425404 multicast packets  14434365 broadcast packets
    88922683 output packets  7182753461 bytes
    14 jumbo packets
    0 output errors  0 collision  0 deferred  0 late collision
    0 lost carrier  0 no carrier  0 babble 0 output discard
    0 Tx pause
  17 interface resets
===========================================================================
secondary# sh run int po2 mem
!Command: show running-config interface port-channel2 membership
!Time: Wed Feb 25 07:56:41 2009
version 5.2(1)N1(1b)
interface port-channel2
  description ***Link to FI-A in R17***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  spanning-tree port type edge
  spanning-tree bpdufilter enable
interface Ethernet1/8
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 2 mode active
interface Ethernet1/9
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 2 mode active
interface Ethernet1/10
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 2 mode active
===========================================================================
secondary# sh run int po3 mem
!Command: show running-config interface port-channel3 membership
!Time: Wed Feb 25 07:58:30 2009
version 5.2(1)N1(1b)
interface port-channel3
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  spanning-tree port type edge
  spanning-tree bpdufilter enable
interface Ethernet1/3
  description ***Link to FI-A in R17***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 3 mode active
interface Ethernet1/4
  description ***Link to FI-A in R17***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 3 mode active
interface Ethernet1/5
  description ***Link to FI-B in R18***
  switchport mode trunk
  switchport trunk allowed vlan 12-13,21,101-600
  channel-group 3 mode active
===========================================================================
secondary# sh int po2
port-channel2 is up
  Hardware: Port-Channel, address: 002a.6a0a.4d6f (bia 002a.6a0a.4d6f)
  Description: ***Link to FI-A in R17***
  MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA
  Port mode is trunk
  full-duplex, 10 Gb/s
  Input flow-control is off, output flow-control is off
  Switchport monitor is off
  EtherType is 0x8100
  Members in this channel: Eth1/8, Eth1/9, Eth1/10
  Last clearing of "show interface" counters never
  30 seconds input rate 1752 bits/sec, 0 packets/sec
  30 seconds output rate 1016 bits/sec, 0 packets/sec
  Load-Interval #2: 5 minute (300 seconds)
    input rate 832 bps, 0 pps; output rate 496 bps, 0 pps
  RX
    76009142 unicast packets  544440 multicast packets  228999 broadcast packets
    76782581 input packets  146179423660 bytes
    68566412 jumbo packets  0 storm suppression bytes
    0 runts  0 giants  0 CRC  0 no buffer
    0 input error  0 short frame  0 overrun   0 underrun  0 ignored
    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
    0 input with dribble  0 input discard
    0 Rx pause
  TX
    192711593 unicast packets  154928956 multicast packets  31420967 broadcast packets
    379061516 output packets  385914168860 bytes
    179761364 jumbo packets
    0 output errors  0 collision  0 deferred  0 late collision
    0 lost carrier  0 no carrier  0 babble 0 output discard
    0 Tx pause
  24 interface resets
===========================================================================
secondary# sh int po3
port-channel3 is up
  Hardware: Port-Channel, address: 002a.6a0a.4d6a (bia 002a.6a0a.4d6a)
  Description: ***Link to FI-B in R18***
  MTU 1500 bytes, BW 30000000 Kbit, DLY 10 usec
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA
  Port mode is trunk
  full-duplex, 10 Gb/s
  Input flow-control is off, output flow-control is off
  Switchport monitor is off
  EtherType is 0x8100
  Members in this channel: Eth1/3, Eth1/4, Eth1/5
  Last clearing of "show interface" counters never
  30 seconds input rate 456 bits/sec, 0 packets/sec
  30 seconds output rate 1784 bits/sec, 0 packets/sec
  Load-Interval #2: 5 minute (300 seconds)
    input rate 456 bps, 0 pps; output rate 912 bps, 0 pps
  RX
    75986748 unicast packets  490267 multicast packets  124569 broadcast packets
    76601584 input packets  146159548726 bytes
    68566413 jumbo packets  0 storm suppression bytes
    0 runts  0 giants  0 CRC  0 no buffer
    0 input error  0 short frame  0 overrun   0 underrun  0 ignored
    0 watchdog  0 bad etype drop  0 bad proto drop  0 if down drop
    0 input with dribble  0 input discard
    0 Rx pause
  TX
    192585042 unicast packets  190939131 multicast packets  13399201 broadcast packets
    396923374 output packets  386206869311 bytes
    179761514 jumbo packets
    0 output errors  0 collision  0 deferred  0 late collision
    0 lost carrier  0 no carrier  0 babble 0 output discard
    0 Tx pause
  24 interface resets
===========================================================================
We have removed vPC configuration as we are facing same problem as i said in my previous post
id     Port        Status Consistency Reason                     Active vlans
2      Po2         up     failed      vpc port channel           -
                                      mis-config due to vpc
                                      links in the 2 switches
                                      connected to different
                                      partners
Do let me know if anything else is required from my end
-amit

Similar Messages

  • Configuration Settings for Postal Adress Validation and Duplicate Check

    Hi,
    What are The Configuration settings for Postal adress validation and Duplicate Check for Accounts(BP'S) in CRM 7.0 version
    Can some one send me the configuration settings for Postal Adress validation and Duplicate Check
    Thanks & Regards
    Kishor Kumar

    Hi kishore kumar,
    For the Postal code Validation you need to install and configure the following
    Outside of your SAP system:
    1. Install Data Services and the Address Directories.
    2. Install Data Services Component.
    3. Install the RFC Server.
    On your SAP system:
    4. Install the BAdIs from the previous version of this product.
    5. Install the BAdIs support package from this version.
    6. Run the post-installation tasks required of a new installation of the BAdIs.
    7. Activate the IC WebClient, if desired.     
    Thanks
    Jayakrishnan Nair

  • GUID for relation between BP and Sales Org?

    Hi,
    I need a GUID for the relation between a business partner and the sales org. I already have a GUID for the sales org, and one for the BP, but I also need one for the relation itself in addition to the field RelNr in BUT050.
    What table are these stored in?
    Regards
    Thomas

    Hello Manuel,
    in neither of these tables is a field for a GUID for the relation, there is only one GUID for the business partner set.
    Since my GUID does not really need to be globally unique, but rather locally, I will now use the FM BUPA_MWXT_RELKEY_TO_RELGUID (which basically concats both partner numbers and the partner relationship number).
    Thanks for your help, though.
    Thomas

  • Configuration guide for ESS/MSS mySAP ERP 2005

    Hi
    Can you please send me configuration guide for ESS/MSS mySAP ERP 2005.
    Thanks in advance
    Regards
    Gauri

    http://service.sap.com/instguides
    --> SAP Business Suite Applications
    --> SAP ERP
    --> mySAP ERP 2005
    --> Upgrade
    --> Upgrade Documentation - mySAP ERP 2005 SR2
    There choose your database and operating system.
    If you're looking for functional details check
    http://service.sap.com/releasenotes

  • Help on Business Scenario Configuration Guide for SRM Server 5.5

    hai friends
    where can i get Business Scenario Configuration Guide.for Version SRM server 5.5
    i found for 4.0 and 5.0 but not for 5.5 Please let me know the link of market place
    thanks
    Regards
    Krishna

    Hi Krishna,
    You can find all configuration guides at http://service.sap.com/ibc. For SRM server 5.5 (SRM5.0), the configuration guide has to be downloaded from Solution Manager.
    Solution Manager is must for all new version implementations now.
    Regards,
    Prashant
    Do reward points for helpful answers

  • Configuration guide for Action Control Matrix

    Hi, Does anyone configuration guide for action control and status matrix for VMS for Equipment master, General Object creation, Master warranty creation and assignement for the object VELO.

    I have seen this as well as the SAP best practices configuration guide, they do not talk about the status for CREQ. We have defined it as secondary action and executed the action but it does not create the equiment. The CS/Plant maintenance does not seem to recognise objects created from VELO. Although the documentation talks of  VELO as equipment categry along with the standard equipement category EQ, we are not sure if we have to add VELO as equipment category (add how to add as well) so that the vehicle master details can be carried from VELO into equipment for warranty processing.
    Thanks

  • Configuration Guide for Time Management

    Can anyone send me the configuration guide for Time Management

    The following is the config. document of TM. check the threads u will get some more good responses and close the thread if u find the response is good enough
    I think its helpful to u.
    IMG  Personnel Time Management  Work Schedules  Define Public Holiday Classes
    IMG  Personnel Time Management  Work Schedules  Personnel Subarea Groupings  Group Personnel Subareas for the Work Schedule
    IMG  Personnel Time Management  Work Schedules  Personnel Subarea Groupings  Group Personnel Subareas for theDaily Work Schedule
    IMG  Personnel Time Management  Work Schedules  Daily Work Schedules  Define Daily Work Schedules
    IMG  Personnel Time Management  Work Schedules  Period Work Schedules  Define Period Work Schedules.
    IMG  Personnel Time Management  Work Schedules  Day Types  Define Day Types.
    IMG  Personnel Time Management  Work Schedules  Day Types  Define Day Types.
    IMG  Personnel Time Management  Work Schedules  Day Types  Define Special Days.
    IMG  Personnel Time Management  Work Schedules  Work Schedule Rules and Work Schedules  Define Employee Subgroup Groupings
    IMG  Personnel Time Management  Work Schedules  Work Schedule Rules and Work Schedules  Define Groupings for the Public Holiday Calendar.
    IMG  Personnel Time Management  Work Schedules  Work Schedule Rules and Work Schedules  Set Work Schedule Rules and Work Schedules.
    IMG  Personnel Time Management  Work Schedules  Work Schedule Rules and Work Schedules  Generate Work Schedules Manually
    IMG  Personnel Time Management  Work Schedules  Planned Working Time  Set Default Value for the Work Schedule.
    IMG  Personnel Time Management  Work Schedules  Planned Working Time  Set Default Value for Time Management Status.
    IMG  Personnel Time Management  Time Data Recording and Administration  Substitutions  Define Personnel Subareas for Substitution Types.
    IMG  Personnel Time Management  Time Data Recording and Administration  Substitutions  Set Defaults for Substitution Types.
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Group Personnel Subareas for Attendances and Absences.
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Define Absence Types.
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Absence Counting  Define Counting Classes for the Period Work Schedule.
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Absence Counting  Rules for Absence Counting (New)  Group Employee Subgroups for Time Quotas.
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Absence Counting  Rules for Absence Counting (New)  Group Personnel Subareas for Time Quotas
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Absence Counting  Rules for Absence Counting (New)  Define Rules for Rounding Counted Absences
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Absence Counting  Rules for Absence Counting (New)  Define Counting Rules
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Absence Counting  Rules for Absence Counting (New)  Define Counting Rules  Deduction rules for Absence quotas
    IMG  Personnel Time Management  Time Data Recording and Administration  Absences  Absence Catalog  Absence Counting  Assign Counting Rules to Absence Types.
    IMG  Personnel Time Management  Time Data Recording and Administration  Attendances/Actual Working Times  Define Attendance Types.
    IMG  Personnel Time Management  Time Data Recording and Administration  Attendances/Actual Working Times  Attendance counting  Rules for Attendance counting (New)  Assign Counting Rules to Attendance Types.
    IMG  Personnel Time Management  Time Data Recording and Administration  Managing Time Accounts Using Attendance/Absence Quotas  Time Quota Types  Define Absence Quota Types.
    IMG  Personnel Time Management  Time Data Recording and Administration  Managing Time Accounts Using Attendance/Absence Quotas  Calculating Absence Entitlements  Automatic Accrual of Absence Quotas  Permit Quota Generation Without Time Evaluation.
    IMG  Personnel Time Management  Time Evaluation  Time Evaluation Settings  Set Personnel Subarea Groupings for Time Recording.
    IMG  Personnel Time Management  Time Data Recording and Administration  Managing Time Accounts Using Attendance/Absence Quotas  Calculating Absence Entitlements  Rules for Generating Absence Quotas  Set Base Entitlements  Base Entitlement for Absence Quota Generation.
    IMG  Personnel Time Management  Time Data Recording and Administration  Managing Time Accounts Using Attendance/Absence Quotas  Calculating Absence Entitlements  Rules for Generating Absence Quotas  Determine Validity and Deduction Periods.
    IMG  Personnel Time Management  Time Data Recording and Administration  Managing Time Accounts Using Attendance/Absence Quotas  Calculating Absence Entitlements  Rules for Generating Absence Quotas  Set Base Entitlements  Define Generation Rules for Quota Selection.
    Edited by: Sikindar on Feb 11, 2008 6:05 PM

  • Configuration guide for ASA Ipsec.

    Ho guys.
    I need configuration guide for ASA Ipsec using Cli.
    Thank you.
    Sent from Cisco Technical Support iPad App

    Hi,
    please check the below link
    http://www.cisco.com/en/US/products/ps9422/products_configuration_example09186a0080b4ae61.shtml?referring_site=smartnavRD
    http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00808c9950.shtml
    Thanks and Regards,
            ROHAN 

  • Configuration Guide for cProjects Version 4.0

    Hi All,
    Does anyone of you have the Configuration Guide for cProjects Version 4.0. Would appreciate if anyone could mail me, my mail id is [email protected]
    Thanks & Regards,
    Stephen

    Hi,
    for cProjects 4.5 information on the configration guide can be found in note 1119326.
    in general use http://service.sap.com/instguides and navigate to
    "SAP Business Suite Applications" > "SAP PLM"
    and there you can find the guides for all delivered cProjects releases.
    I hope this provides the pointer needed for all the other participants as well.
    Best regards,
    Thomas

  • Configuration guide for drop shipments

    Hello all,
    Pl. post any link/documents/Configuration guide for configuring the drop shipment process in SAP.
    Thanks,
    Maxx

    Maxx,
    I assume when you say "Drop shipments", you are referring to the process where a customer orders product from your company; you procure the product from a Vendor, the Vendor ships the product directly to the Customer; and you invoice the customer. SAP calls this Third party order processing.  SAP has two Best Practices, Here are the Business Process docs, and configuration guides.
    Third party order processing w/Ship notification
    http://help.sap.com/bp_bl604/BBLibrary/Documentation/107_BPP_EN_US.doc
    http://help.sap.com/bp_bl604/BBLibrary/Documentation/107_BB_ConfigGuide_EN_US.doc
    Third party order processing without Ship notification
    http://help.sap.com/bp_bl604/BBLibrary/Documentation/114_BPP_EN_US.doc
    http://help.sap.com/bp_bl604/BBLibrary/Documentation/114_BB_ConfigGuide_EN_US.doc
    Rgds,
    DB49

  • Configuration guide for cFolders 4.5

    Hi,
    I couldnt find the latest configuration guide for cFolders.. I checked in service place, but couldnt find for 4.5
    Can someone send me the link where I can find configuration guide of cFolders 4.5
    Thanks in advance
    Aby

    Hi,
    Please check below note,this may help  you
    1289589 cFolders 4.0 and 4.5 released for installation on NW 7.01
    SAP Note 1088160 - cProjects 4.5 - FAQ note
    1119326 Configuration guide for cProjects 4.50
    Regards
    Ravindra

  • Configuration Guide for cProjects

    Hi,
    Does anyone have or know where to download Configuration Guide for cProjects? Please help.
    Thanks.

    Hi Thang,
    Let me know which version of Cproject you are using? is it 3.0, 3.1 or 4.0?
    and let me know your email id too, i shall send you the complete configuration document on CProjects.
    Regards
    Rehman

  • Configuration Guide for BP, Product master, number ranges

    Hi all,
    I am an experienced SD consultant but new to CRM, Right now I have very little knowledge of CRM. I needed configuration steps/guides for BP, product master, and org model mgt. Please no links to market place since i have to access to it.
    thanks in advance.
    Vikrant

    hi
    for people like you SAP has its best practice documents avaiable freely on net
    for your case you need
    C17
    just search it on google,
    you will get it
    it has BP,product and ORg base customisation
    best regards
    ashish

  • SAP Web Dispatcher Configuration guide for Windows

    Hi,
    I am searching for SAP Web Dispatcher Configuration guide for Windows. It is WAS 6.4, SP14 and JAVA. If any one knows this mean please guide.
    Thanks.

    Hi  Mahesh,
    check out the help pages here:
    http://help.sap.com/saphelp_nw04/helpdata/en/f5/51c7d170bc4a98b1b5a0339213af57/frameset.htm
    Regards,
    Pascal

  • Urgent: Step by step configuration guide for workflow

    Hi all,
           Can anybody please proVide me complete step by step configuration guide for SRM 5.0 workflow.FULL POINTS WILL BE AWARDED FOR THE HELPFUL ANSWER..

    hi,
    <b>Check the below PDF file on Workflow:</b>
    http://help.sap.com/printdocu/core/Print46c/en/data/pdf/PSWFL/PSWFL.pdf
    There is a good book from SAP Press that I would
    recommend as a starting point.It's called Practical Workflow for SAP and it is by Alan Rickayzen.
    http://www.sap-press.com/product.cfm?account=&product=H950
    /people/ginger.gatling/blog/2005/12/01/link-workflow-business-objects-to-your-collaboration-tasks
    http://help.sap.com/saphelp_erp2005/helpdata/en/fb/135962457311d189440000e829fbbd/frameset.htm
    http://help.sap.com/saphelp_erp2005/helpdata/en/c5/e4a930453d11d189430000e829fbbd/frameset.htm
    http://help.sap.com/saphelp_erp2004/helpdata/en/a5/172437130e0d09e10000009b38f839/frameset.htm
    http://help.sap.com/saphelp_bw33/helpdata/en/92/bc26a6ec2b11d2b4b5006094b9ea0d/content.htm
    http://help.sap.com/saphelp_bw31/helpdata/en/8d/25f94b454311d189430000e829fbbd/content.htm
    Go through the following:
    1) Goto Tcode PFTC : Standard Task > Create Button>Workflow Templete
    For Create Container
    Element : ZBUS1001006
    Name : ANy Name
    Description
    Data Type & Properties
    Data Type:
    select Object Type : BOR Object Type for BUS1001006
    Properties:
    Parameter Settingd : check all Import, Export & Mandatory Checkboxes
    Basic Data :
    Abbr : Create_View
    Name : Some Name
    Work Item Text : Create View Material & -
    Click on DELE Button & Select Material From The List
    Object Catagory : BOR Object Type
    Object Type : BUS1001006
    Method : View
    Triggering Events
    Obj Catagory Object Type Event
    BOR Object BUS1001006 View
    activate it
    Enter on BUS1001006 Object Type you will get Quadratel<> Button after that
    double click on Quadratel<> button you get green button
    after that the system will generate the task No.
    check in the Event linkage Tcode : SWETYPV
    if you find an entry with your Workflow and linkage active
    goto Tcode : SWEC click on New Entries
    Change Doc Obje Obj Cat Obj Type Event on create
    Material BOJ Obje BUS1001006 View Option Button(Checked)
    save this
    goto Tcode : SWEC
    Change Doc Object : Material
    Obj Catagoty : BOR Type
    Obj Type : BUS1001006
    Event : View
    Check with On Create Button
    Goto SWETYPV
    Obj Catagoty : BOR Type
    Obj Type : BUS1001006
    Event : View
    Receiver Type : Some Work Flow No: WS80000431 like this
    Click on Work flow Builder
    Cheers
    Alfred

Maybe you are looking for

  • How do I add an attachment pdf. to my email on my iPad Air?

    I am trying to upload an attachment pdf. to my email, but when ever I do it doesn't actually attach to the email. I already have the app iCab mobile, and I am doing it through this.  But it still won't work.

  • Where did my iPhoto go?

    Help, my iPhoto disappeared from my dock.  How do I find the applications folder to find out if it is still there?

  • How to encode a string to base64 in java ?

    Hi, I want to send my user name to my SMTP server encoded in base64 . How do I do this ?? Ramesh

  • N97 Photo GPS Issue

    I've been taking a lot of photos recently using the N97 and have also installed Nokia Image Space. However, photos i've taken are miles out when reviewing the map on Flickr - literally miles out and bear no resemblace to the position the original pho

  • Photobooth

    hey guys, i recently did a clean installation of snow leopard then manually moved back all my files. and after that i realized that the photo booth pictures are not showing up in photo booth. i tried dragging them in but no luck. please let me know.