Connecting Cisco ASA TenGig to Nexus 7000
I am attempting to connect an ASA 5585 TenGig to a Nexus 7000 F2 TenGig port.
I am seeing the error message Transceiver validation failed when I insert the SFP into the port. I know that the error is removed when I enter the command switchport mode fex-fabric, and have tried the configuration, but am unable to get the link to come up.at either end. I am also aware that LACP is not supported when switchport mode fex-fabric is configured.
ASA is in multiple context mode with portchannel interfaces allocated to the relevant ASA context. Anyone know if I am overlooking something? Anyone run into this issue before?
Nexus 7000:
Eth1/1 1 eth access down Transceiver validation fa auto(D) 2
Eth1/2 1 eth access down Transceiver validation fa auto(D) 2
interface Ethernet1/1
switchport mode trunk
switchport trunk allowed vlan 1-10
channel-group 2 mode active
no shutdown
interface Ethernet1/2
switchport mode trunk
switchport trunk allowed vlan 2-10
channel-group 2 mode active
no shutdown
interface port-channel2
switchport mode trunk
switchport trunk allowed vlan 2-10
ASA5585:
interface TenGigabitEthernet0/6
channel-group 2 mode active
interface TenGigabitEthernet0/7
channel-group 2 mode active
interface Port-channel2
interface Port-channel2.2
vlan 2
interface Port-channel2.3
vlan 3
context inside
allocate-interface Port-channel2.1
allocate-interface Port-channel2.2
config-url disk0:/inside.cfg
In my case, I was getting this error on a interface of a Nexus C6001 with the FET-10G transceiver. I was able to clear it up by temorarily replacing and configuring a slower GLC-T which worked as expected. I then removed all the settings an got the FET-10G to link.
Similar Messages
-
Connecting IBM B22 FEXes to Nexus 7000
Hello everybody,
Could someone give an definite answer, better to based on personal experience - is it possible to attach B22 FEX going to the IBM chassis to Nexus 7000 via F2 series 48-port 10G card?
NXOS is currently running 6.1.5a but we plan to upgrade to 6.2.8 or 6.2.12 once we get new 4GB DIMMs for SUP1 modules.
Thanks.In my case, I was getting this error on a interface of a Nexus C6001 with the FET-10G transceiver. I was able to clear it up by temorarily replacing and configuring a slower GLC-T which worked as expected. I then removed all the settings an got the FET-10G to link.
-
Nexus 7000 and 2000. Is FEX supported with vPC?
I know this was not supported a few months ago, curious if anything has changed?
Hi Jenny,
I think the answer will depend on what you mean by is FEX supported with vPC?
When connecting a FEX to the Nexus 7000 you're able to run vPC from the Host Interfaces of a pair of FEX to an end system running IEEE 802.1AX (802.3ad) Link Aggregation. This is shown is illustration 7 of the diagram shown on the post Nexus 7000 Fex Supported/Not Supported Topologies.
What you're not able to do is run vPC on the FEX Network Interface that connect up to the Nexus 7000 i.e., dual-homing the FEX to two Nexus 7000. This is shown in illustrations 8 and 9 of under the FEX topologies not supported on the same page.
There's some discussion on this in the forum post DualHoming 2248TP-E to N7K that explains why it's not supported, but essentially it offers no additional resilience.
From that post:
The view is that when connecting FEX to the Nexus 7000, dual-homing does not add any level of resilience to the design. A server with dual NIC can attach to two FEX so there is no need to connect the FEX to two parent switches. A server with only a single NIC can only attach to a single FEX, but given that FEX is supported by a fully redundant Nexus 7000 i.e., SE, fabrics, power, I/O modules etc., the availability is limited by the single FEX and so dual-homing does not increase availability.
Regards -
With Vignesh R. P.
Welcome to the Cisco Support Community Ask the Expert conversation.This is an opportunity to learn and ask questions of Cisco expert Vignesh R. P. about the Cisco® Nexus 7000 Series Switches and support for the Cisco NX-OS Software platform .
The Cisco® Nexus 7000 Series Switches introduce support for the Cisco NX-OS Software platform, a new class of operating system designed for data centers. Based on the Cisco MDS 9000 SAN-OS platform, Cisco NX-OS introduces support for virtual device contexts (VDCs), which allows the switches to be virtualized at the device level. Each configured VDC presents itself as a unique device to connected users within the framework of that physical switch. The VDC runs as a separate logical entity within the switch, maintaining its own unique set of running software processes, having its own configuration, and being managed by a separate administrator.
Vignesh R. P. is a customer support engineer in the Cisco High Touch Technical Support center in Bangalore, India, supporting Cisco's major service provider customers in routing and MPLS technologies. His areas of expertise include routing, switching, and MPLS. Previously at Cisco he worked as a network consulting engineer for enterprise customers. He has been in the networking industry for 8 years and holds CCIE certification in the Routing & Switching and Service Provider tracks.
Remember to use the rating system to let Vignesh know if you have received an adequate response.
Vignesh might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Data Center sub-community discussion forum shortly after the event. This event lasts through through January 18, 2013. Visit this forum often to view responses to your questions and the questions of other community members.Hi Vignesh
Is there is any limitation to connect a N2K directly to the N7K?
if i have a an F2 card 10G and another F2 card 1G and i want to creat 3 VDC'S
VDC1=DC-Core
VDC2=Aggregation
VDC3=Campus core
do we need to add a link between the different VDC's
thanks -
Smart call home - HTTPS transport from the Nexus 7000 to Cisco
hi
i try configured call home on nexus 7000 with https transport and proxy server
i follow this guide -
http://www.cisco.com/en/US/docs/switches/lan/smart_call_home/QuickStart_NX7000.pdf
and configured this :
callhome
email-contact XXXXXXXXXXX
phone-contact XXXXXXXXXXX
streetaddress XXXXXXXXXXXXXXXX
destination-profile CiscoTAC-1 transport-method http
destination-profile CiscoTAC-1 http https://tools.cisco.com/its/service/oddce/services/DDCEService
transport http use-vrf management
transport http proxy server XXXXXXXXXX port 8080 --------- XXXXXXXXX = my proxy server
transport http proxy enable
enable
periodic-inventory notification interval 30
i have a problem to install the security certificate , i follow thw guide but i get the error :
failed to load or parse certificate
could not perform CA authentication
when i try test call home eith the command : callhome test
trying to send test callhome message
warning:no callhome message sent
email configuration incomplete for destination profile:full_txt
email configuration incomplete for destination profile:short_txt
Error in transporting http message for CiscoTAC-1
http: Received HTTP code 407 from proxy after CONNECT
i guess the problem is because i didnt install the certificate , how can i install the certificate ?
is this the real problem ?I agree with Bryan that the easiest proxy server to setup for the nexus 7000 is the Transport Gateway. The documentation (certificates) is setup to allow you to connect to a Cisco Transport Gateway or directly into tools.cisco.com. Both have a Cisco certificate.
But that doesn't explain your issue. To answer your issue, you need to look here
http://www.cisco.com/en/US/docs/switches/lan/smart_call_home/SCH31_Ch6.html#wp1039385
except you need your proxy server's chained certificate in PEM format since the Nexus 7000 is going to terminate at your proxy server. Take a look at this line in the documentation.
Input (cut & paste) the CA certificate (chain) in PEM format
The error code 407 you indicated makes sense and indicates "Proxy Authentication Required". You need the certificate installed first. NX-OS uses the openssl crypto library to implement the cert-pki feature if that helps. A complete certificate chain is required. Also, you might make sure the CRL (certificate revocation list) is set to none so it doesn't do that first.
revocation-check none
The 4 chained certificates given in the documentation are tools.cisco.com.cer, Verisign-G3-SSCA.cer, Verisign-G3-PRCA.cer, Verisign-Root-CA.cer. The non-nexus 7000 devices just use the last one. Most likely you need a certificate that looks like
your proxy server.cer,Verisign-G3-SSCA.cer, Verisign-G3-PRCA.cer, Verisign-Root-CA.cer
If you are using your own root CA (which typically are taken off-line after authorizing subordinate CAs for security reasons) , then make sure that their certificates are in the correct order to be processed so each can be authenticated.
Now you can see why a Cisco proxy server (Transport Gateway) is easier to setup. -
Broadcom LiveLink : Receiving MAC flaps with Cisco Nexus 7000
We are migrating from using two Nortel 8600's running VRRP at the distribution to Cisco Nexus 7K's using HSRP. So we have a server connected to two 3750G switches which then connect to the Nexi (previously the 8600's). As soon as we connected the 3750's to the Nexus and moved the gateway to Nexus, LiveLink forces all the servers to alternate traffic between NIC1 and NIC2.
Since LiveLink is a teaming application, it uses virtual mac for nic1 and nic2, but the virtual mac associated with the IP address moves to the active link.
LiveLink is used to check the availability of the gateway by polling the gateway out of each interface using an ARP request.
The problem does not exhibit itself in our Cisco VSS environment, and with Nortel's VRRP. I tried running VRRP on the Nexus but no joy.
Anyone know of a bug that could cause this issue?Unfortunately we have LiveLink enabled on most of our Windows servers in our data centers. One of my colleagues sent me this bug issue. I'm not sure if this is the cause, but it's worth trying. We will update the NxOs (currently on 5.1.1) next week and see if that fixes the problem.
•CSCtl85080
Symptom: Incomplete Address Resolution Protocol (ARP) entries are observed on a Cisco Nexus 7000 Series switch, along with partial packet loss and a memory leak.
Conditions: This symptom might be seen when ARP packets have a nonstandard size (that is, greater than 64 bytes).
Workaround: This issue is resolved in 5.1.3. -
Virtualized Lab Infrastructure - 3560G connecting to a Nexus 7000 - Help!
Hi all,
I've been struggling with the configuration for my small environment for a week or so now, and being a Cisco beginner, I'm worried about going down the wrong path, so I'm hoping someone on here would be able to help with my lab configuration.
As you can see from the graphic, I have been allocated VLANs 16-22 for my use, on the Nexus 7000. There are lots of other VLANs in use on the Nexus, by other groups, most of which are routable between one another. VLAN 99 is used for switch management, and VLAN 11, is where the Domain Controller, DHCP and Windows Deployment Server reside for the lab domain. Servers across different VLANs use this DC/DHCP/WDS set of servers. These VLANS route out to the internet successfully.
I have been allocated eth 3/26 on the Nexus, as my uplink connection to my own ToR 3560G. All of my servers, of which there are around 8 in total, are connected to the 3560. I have enabled IP routing on the 3560, and created VLANs 18-22, providing an IP on each. This config has been assigned to all 48 gigabit ports on the 3560 (using the commands in the graphic), and each Windows Server 2012 R2 Hyper-V host connects to the 3560 via 4 x 1GbE connections. On each Hyper-V host, the 4 x 1GbE ports are teamed, and a Hyper-V vSwitch is bound to that team. I then assign the VLAN ID at the vNIC level.
Routing between the VLANs is currently working fine - As a test, i can put 2 of the servers on different VLANs, each with their respective VLAN default gateway, and they can ping between one another.
My challenge is, I'm not quite sure what i need to do for the following:
1) How should I configure the uplink gi 0/52 on the 3560 to enable my VLANs to reach the internet?
2) How should I configure eth 3/26 on the Nexus?
3) I need to ensure that the 3560 is also on the management VLAN 99 so it can be managed successfully.
4) I do not want to route to VLAN 11, as i intend to have my own domain (DC/DNS/DHCP/WDS)
Any help or guidance you can provide would be much appreciated!
Thanks!
MattHi again Jon,
OK, been battling with it a little more.
Here's the config for the 3560:
Current configuration : 11643 bytes
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname CSP_DX_Cluster
no aaa new-model
vtp mode transparent
ip subnet-zero
ip routing
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
vlan 16,18-23,99
interface GigabitEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk native vlan 18
switchport trunk allowed vlan 18-22
switchport mode trunk
spanning-tree portfast trunk
<same through interface GigabitEthernet0/48>
interface GigabitEthernet0/52
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 16,99
switchport mode trunk
interface Vlan1
no ip address
interface Vlan16
ip address 10.0.6.2 255.255.255.252
interface Vlan18
ip address 10.0.8.1 255.255.255.0
interface Vlan19
ip address 10.0.9.1 255.255.255.0
interface Vlan20
ip address 10.0.12.1 255.255.255.0
interface Vlan21
no ip address
interface Vlan22
ip address 10.0.14.1 255.255.255.0
interface Vlan99
ip address 10.0.99.87 255.255.255.0
ip classless
ip route 0.0.0.0 0.0.0.0 10.0.6.1
ip http server
control-plane
l
end
At the Nexus end, the port connecting to the 3560 is configured as:
interface Ethernet3/26
description DX_3560_uplink
switchport
switchport mode trunk
switchport trunk allowed vlan 16,99
no shutdown
Now, the problem I'm currently having, is that on the 3560, things route fine, between VLANs. However, from on a server within one of the VLANs, say, 18, trying to ping the default gateway of the 3560 fails. I can ping 10.0.6.2 which is the 3560-end of VLAN 16, but i can't get over to 10.0.6.1 and beyond. I suspect, it's relating to what you said about "the only thing missing is you also need routes on the Nexus switch for the IP subnets on your 3560 and the next hop IP would be 10.0.6.2 ie the vlan 16 SVI IP on the 3560"
I suspect that, in layman's (my terms!) terms, the Nexus simply doesn't know about the networks 10.0.8.1 (VLAN 18), 10.0.9.1 (VLAN 19) and so on.
So, i need routes on my Nexus to fix this. The problem is, I'm not quite sure what that looks like.
Would it be:
ip route 10.0.8.0 255.255.255.0 10.0.6.2
ip route 10.0.9.0 255.255.255.0 10.0.6.2 and so on?
To give a bit of history, prior to me creating VLANs 18-22 on the 3560, all VLANs originally existing on the Nexus. Everything routed fine out to the internet, for all of the VLANs (with the same subnet settings that i have configured, i.e. 10.0.8.x for VLAN 18 etc), so i'm presuming once I get the Nexus to understand that the IP subnets live on the 3560, traffic should flow successfully to the internet.
Should.... :-) -
Internet Connection Became Slow after Introduction of Cisco ASA 5505 to the Network
I configured a Cisco ASA 5505 (Version Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
in transparent firewall mode and inserted after Cisco 1700 router. However, the internet connection became very slow and users are compaining that they cannot load any pages.
My setup looks like:
Internet --> Cisco 1700 --> Cisco ASA 5505 --> LAN
The license information is:
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
The flash activation key is the SAME as the running key.
My running-config looks like:
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Vlan1
nameif inside
security-level 100
no shut
interface Vlan2
nameif outside
security-level 0
no shut
interface Ethernet0/0
switchport access vlan 2
no shut
interface Ethernet0/1
no shut
interface Ethernet0/2
no shut
interface Ethernet0/3
no shut
interface Ethernet0/4
no shut
interface Ethernet0/5
no shut
interface Ethernet0/6
no shut
interface Ethernet0/7
no shut
passwd 2KFQnbNIdI.2KYOU encrypted
regex urllist1 ".*\.([Ee][Xx][Ee]|[Cc][Oo][Mm]|[Bb][Aa][Tt]) HTTP/1.[01]"
regex urllist2 ".*\.([Pp][Ii][Ff]|[Vv][Bb][Ss]|[Ww][Ss][Hh]) HTTP/1.[01]"
regex urllist3 ".*\.([Dd][Oo][Cc]|[Xx][Ll][Ss]|[Pp][Pp][Tt]) HTTP/1.[01]"
regex urllist4 ".*\.([Zz][Ii][Pp]|[Tt][Aa][Rr]|[Tt][Gg][Zz]) HTTP/1.[01]"
regex domainlist1 "\.facebook\.com"
regex domainlist2 "\.diretube\.com"
regex domainlist3 "\.youtube\.com"
regex domainlist4 "\.vimeo\.com"
regex applicationheader "application/.*"
regex contenttype "Content-Type"
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_in extended permit ip any any
access-list inside_mpc extended permit tcp any any eq www
access-list inside_mpc extended permit tcp any any eq 8080
pager lines 24
mtu outside 1500
mtu inside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domainlist1
match regex domainlist2
match regex domainlist3
match regex domainlist4
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map type regex match-any URLBlockList
match regex urllist1
match regex urllist2
match regex urllist3
match regex urllist4
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all AppHeaderClass
match response header regex contenttype regex applicationheader
class-map httptraffic
match access-list inside_mpc
class-map type inspect http match-all BlockURLsClass
match request uri regex class URLBlockList
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action drop-connection
class AppHeaderClass
drop-connection log
match request method connect
drop-connection log
class BlockDomainsClass
reset log
class BlockURLsClass
reset log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
policy-map inside-policy
class httptraffic
inspect http http_inspection_policy
service-policy global_policy global
service-policy inside-policy interface inside
prompt hostname context
Cryptochecksum:8ab1a53df6ae3c202aee236d6080edfd
: end
Could the slow internet connection be due to license limitations? Or is there something wrong with my configuration?
Please see the configuration and help.
ThanksI have re-configured the ASA 5505 yesterday and so far it's working fine. I am not sure if the problem will re-appear later on. Anyways here is my sh tech-support
ciscoasa# sh tech-support
Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
Compiled on Wed 15-Aug-07 16:08 by builders
System image file is "disk0:/asa723-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 14 hours 16 mins
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Int: Internal-Data0/0 : address is 001f.9ee8.ffa2, irq 11
1: Ext: Ethernet0/0 : address is 001f.9ee8.ff9a, irq 255
2: Ext: Ethernet0/1 : address is 001f.9ee8.ff9b, irq 255
3: Ext: Ethernet0/2 : address is 001f.9ee8.ff9c, irq 255
4: Ext: Ethernet0/3 : address is 001f.9ee8.ff9d, irq 255
5: Ext: Ethernet0/4 : address is 001f.9ee8.ff9e, irq 255
6: Ext: Ethernet0/5 : address is 001f.9ee8.ff9f, irq 255
<--- More --->
7: Ext: Ethernet0/6 : address is 001f.9ee8.ffa0, irq 255
8: Ext: Ethernet0/7 : address is 001f.9ee8.ffa1, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
Serial Number: JMX1211Z2N4
Running Activation Key: 0xaf0ed046 0xbcf18ebf 0x80b38508 0xba785cc0 0x05250493
Configuration register is 0x1
Configuration has not been modified since last system restart.
<--- More --->
------------------ show clock ------------------
18:32:58.254 UTC Tue Nov 26 2013
------------------ show memory ------------------
Free memory: 199837144 bytes (74%)
Used memory: 68598312 bytes (26%)
Total memory: 268435456 bytes (100%)
------------------ show conn count ------------------
1041 in use, 2469 most used
------------------ show xlate count ------------------
0 in use, 0 most used
------------------ show blocks ------------------
SIZE MAX LOW CNT
0 100 68 100
<--- More --->
4 300 299 299
80 100 92 100
256 100 94 100
1550 6174 6166 6174
2048 1124 551 612
------------------ show blocks queue history detail ------------------
History buffer memory usage: 2136 bytes (default)
------------------ show interface ------------------
Interface Internal-Data0/0 "", is up, line protocol is up
Hardware is y88acs06, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 001f.9ee8.ffa2, MTU not set
IP address unassigned
18491855 packets input, 11769262614 bytes, 0 no buffer
Received 213772 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops, 0 demux drops
18185861 packets output, 11626494317 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 late collisions, 0 deferred
<--- More --->
0 input reset drops, 0 output reset drops
input queue (curr/max packets): hardware (0/0) software (0/0)
output queue (curr/max packets): hardware (0/55) software (0/0)
Control Point Interface States:
Interface number is unassigned
Interface Internal-Data0/1 "", is administratively down, line protocol is up
Hardware is 88E6095, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 0000.0003.0002, MTU not set
IP address unassigned
18184216 packets input, 11625360131 bytes, 0 no buffer
Received 206655 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 switch ingress policy drops
18490057 packets output, 11768078777 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Loopback0 "_internal_loopback", is up, line protocol is up
Hardware is VirtualMAC address 0000.0000.0000, MTU 1500
IP address 127.1.0.1, subnet mask 255.255.0.0
<--- More --->
Traffic Statistics for "_internal_loopback":
1 packets input, 28 bytes
1 packets output, 28 bytes
1 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 28
Interface config status is active
Interface state is active
Interface Vlan1 "inside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa2, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "inside":
7742275 packets input, 903584114 bytes
10645034 packets output, 10347291114 bytes
184883 packets dropped
1 minute input rate 320 pkts/sec, 35404 bytes/sec
1 minute output rate 325 pkts/sec, 313317 bytes/sec
<--- More --->
1 minute drop rate, 17 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
Control Point Interface States:
Interface number is 1
Interface config status is active
Interface state is active
Interface Vlan2 "outside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa3, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "outside":
10750090 packets input, 10432619059 bytes
7541331 packets output, 870613684 bytes
109911 packets dropped
1 minute input rate 328 pkts/sec, 313770 bytes/sec
1 minute output rate 301 pkts/sec, 32459 bytes/sec
1 minute drop rate, 2 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
Control Point Interface States:
Interface number is 2
<--- More --->
Interface config status is active
Interface state is active
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001f.9ee8.ff9a, MTU not set
IP address unassigned
10749794 packets input, 10630700889 bytes, 0 no buffer
Received 2506 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
3 switch ingress policy drops
7541070 packets output, 1028190148 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/1 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
<--- More --->
Available but not configured via nameif
MAC address 001f.9ee8.ff9b, MTU not set
IP address unassigned
7741977 packets input, 1064586806 bytes, 0 no buffer
Received 211282 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
10644663 packets output, 10543362751 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/2 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9c, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
<--- More --->
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/3 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9d, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
<--- More --->
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/4 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9e, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
<--- More --->
Interface number is unassigned
Interface Ethernet0/5 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9f, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/6 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
<--- More --->
MAC address 001f.9ee8.ffa0, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/7 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ffa1, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
<--- More --->
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
------------------ show cpu usage ------------------
CPU utilization for 5 seconds = 12%; 1 minute: 11%; 5 minutes: 11%
------------------ show cpu hogging process ------------------
Process: Dispatch Unit, NUMHOG: 1, MAXHOG: 133, LASTHOG: 140
LASTHOG At: 04:45:59 UTC Nov 26 2013
PC: 8be0f7
Traceback: 8bed19 8bf553 302b87 3030a5 2fad69 7674bf 75ca16
c6251d c62a4c c62f6c 75c653 767820 797f64 769c85
<--- More --->
------------------ show process ------------------
PC SP STATE Runtime SBASE Stack Process
Mwe 00c9bb24 01bb8700 013e3250 0 01733fc8 15616/16384 emweb/cifs
Lwe 001072ac 0176f9c4 013e32d0 0 0176d9f0 8132/8192 block_diag
Mrd 00223a67 01783d5c 013e33b0 314854 0177be18 25752/32768 Dispatch Unit
Msi 00f82847 01b07b84 013e3250 229 01b05bc0 7984/8192 y88acs06 OneSec Thread
Mwe 0011b1a5 01b09cfc 013e3250 0 01b07d88 7864/8192 Reload Control Thread
Mwe 00120606 01b1260c 013e5258 0 01b10988 7256/8192 aaa
Mwe 001486aa 01b19404 013e5ae8 0 01b15450 16020/16384 CMGR Server Process
Mwe 0014c3c5 01b1b4d4 013e3250 0 01b19570 7968/8192 CMGR Timer Process
Lwe 002227a1 01b239b4 013ee360 0 01b219f0 7524/8192 dbgtrace
Mwe 004e1ba5 01b29c34 013e3250 157 01b27d50 6436/8192 eswilp_svi_init
Mwe 01064b1d 01b4a7f4 013e3250 0 01b48890 7848/8192 Chunk Manager
Msi 008b61b6 01b52d54 013e3250 230 01b50da0 7856/8192 PIX Garbage Collector
Lsi 00ecb6ac 01b54e94 013e3250 12 01b52ec0 7552/8192 route_process
Mwe 008a5ddc 01b5dc04 0133b430 0 01b5bc40 8116/8192 IP Address Assign
Mwe 00acb779 01b60604 01346e10 0 01b5e640 8116/8192 QoS Support Module
Mwe 0091eba9 01b6275c 0133c530 0 01b60798 8116/8192 Client Update Task
Lwe 01083c8e 01b656d4 013e3250 123088 01b63770 7840/8192 Checkheaps
Mwe 00acfd7d 01b6b824 013e3250 623 01b69ad0 3476/8192 Quack process
Mwe 00b2a260 01b6dad4 013e3250 22 01b6bbf0 7364/8192 Session Manager
Mwe 00c55efd 01b78564 031d0478 4 01b74a50 14768/16384 uauth
<--- More --->
Mwe 00be3c9e 01b7aaec 0135c010 0 01b78b28 7524/8192 Uauth_Proxy
Mwe 00c52759 01b80e0c 01361770 0 01b7ee88 7712/8192 SMTP
Mwe 00c3f7b9 01b82eec 01361710 0 01b80fa8 7412/8192 Logger
Mwe 00c3fd26 01b8502c 013e3250 0 01b830c8 7492/8192 Thread Logger
Mwe 00f62272 01b9596c 013ac520 0 01b939c8 7188/8192 vpnlb_thread
Msi 00b4097c 01c598c4 013e3250 190 01c578f0 8000/8192 emweb/cifs_timer
Msi 005bd338 017a909c 013e3250 25855 017a7108 7412/8192 arp_timer
Mwe 005c76bc 01b486e4 013fba50 20643 01b46770 7348/8192 arp_forward_thread
Mwe 00c5a919 023fa5fc 013619e0 0 023f8648 7968/8192 tcp_fast
Mwe 00c5a6e5 023fc624 013619e0 0 023fa670 7968/8192 tcp_slow
Mwe 00c754d1 0240d42c 013628a0 0 0240b478 8100/8192 udp_timer
Mwe 0019cb17 01b404a4 013e3250 0 01b3e530 7984/8192 CTCP Timer process
Mwe 00efe8b3 0308c15c 013e3250 0 0308a208 7952/8192 L2TP data daemon
Mwe 00efef23 0308e194 013e3250 0 0308c230 7968/8192 L2TP mgmt daemon
Mwe 00eea02b 030c62ac 013a5c10 43 030c2338 16244/16384 ppp_timer_thread
Msi 00f62d57 030c82f4 013e3250 264 030c6360 7924/8192 vpnlb_timer_thread
Mwe 001b96e6 01b7cbbc 01b1e9c8 1 01b7ac48 7728/8192 IPsec message handler
Msi 001c9bac 01b8d4dc 013e3250 2917 01b8b548 7648/8192 CTM message handler
Mwe 00af93b8 031465b4 013e3250 0 03144640 7984/8192 ICMP event handler
Mwe 00831003 0314a724 013e3250 387 031467b0 16100/16384 IP Background
Mwe 0021b267 031a83c4 013123c0 31 03188450 123488/131072 tmatch compile thread
Mwe 009f2405 03290044 013e3250 0 0328c0c0 16072/16384 Crypto PKI RECV
Mwe 009f305a 03294144 013e3250 0 032901e0 16040/16384 Crypto CA
Mwe 0064d4fd 01b3e24c 013e3250 8 01b3c2f8 7508/8192 ESW_MRVL switch interrupt service
<--- More --->
Msi 00646f5c 032c134c 013e3250 3059378 032bf448 7184/8192 esw_stats
Lsi 008cbb80 032dc704 013e3250 3 032da730 7908/8192 uauth_urlb clean
Lwe 008afee7 034a0914 013e3250 197 0349e9b0 6636/8192 pm_timer_thread
Mwe 0052f0bf 034a35ac 013e3250 0 034a1648 7968/8192 IKE Timekeeper
Mwe 00520f6b 034a8adc 0132e2b0 0 034a4e38 15448/16384 IKE Daemon
Mwe 00bf5c78 034ac7ac 01360680 0 034aa7f8 8100/8192 RADIUS Proxy Event Daemon
Mwe 00bc32de 034ae79c 034dcbe0 0 034ac918 7208/8192 RADIUS Proxy Listener
Mwe 00bf5e0f 034b099c 013e3250 0 034aea38 7968/8192 RADIUS Proxy Time Keeper
Mwe 005aac4c 034b3154 013fb980 0 034b1250 7492/8192 Integrity FW Task
M* 008550a5 0009fefc 013e33b0 3183 034e3b20 24896/32768 ci/console
Msi 008eb694 034ed9d4 013e3250 2370 034ebc40 6176/8192 update_cpu_usage
Msi 008e6415 034f7dac 013e3250 1096 034f5eb8 6124/8192 NIC status poll
Mwe 005b63e6 03517d1c 013fbd10 1963 03515d78 7636/8192 IP Thread
Mwe 005becbe 03519e4c 013fbcb0 3 03517e98 7384/8192 ARP Thread
Mwe 004c2b36 0351befc 013fbae0 0 03519fe8 7864/8192 icmp_thread
Mwe 00c7722e 0351e06c 013e3250 0 0351c108 7848/8192 udp_thread
Mwe 00c5d126 0352008c 013fbd00 0 0351e228 7688/8192 tcp_thread
Mwe 00bc32de 03a6982c 03a5ee18 0 03a679b8 7512/8192 EAPoUDP-sock
Mwe 00266c15 03a6b614 013e3250 0 03a699e0 7032/8192 EAPoUDP
Mwe 005a6728 01b27b94 013e3250 0 01b25c30 7968/8192 Integrity Fw Timer Thread
- - - - 47686621 - - scheduler
- - - - 51253819 - - total elapsed
------------------ show failover ------------------
<--- More --->
ERROR: Command requires failover license
------------------ show traffic ------------------
inside:
received (in 51429.740 secs):
7749585 packets905087345 bytes
67 pkts/sec17013 bytes/sec
transmitted (in 51429.740 secs):
10653162 packets10355908020 bytes
40 pkts/sec201026 bytes/sec
1 minute input rate 412 pkts/sec, 51803 bytes/sec
1 minute output rate 475 pkts/sec, 522952 bytes/sec
1 minute drop rate, 24 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
outside:
received (in 51430.240 secs):
10758403 packets10441440193 bytes
42 pkts/sec203021 bytes/sec
transmitted (in 51430.240 secs):
7548339 packets872053854 bytes
<--- More --->
63 pkts/sec16037 bytes/sec
1 minute input rate 479 pkts/sec, 523680 bytes/sec
1 minute output rate 387 pkts/sec, 46796 bytes/sec
1 minute drop rate, 3 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
_internal_loopback:
received (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Aggregated Traffic on Physical Interface
<--- More --->
Ethernet0/0:
received (in 51431.740 secs):
10758462 packets10640075825 bytes
42 pkts/sec206042 bytes/sec
transmitted (in 51431.740 secs):
7548383 packets1029818127 bytes
63 pkts/sec20023 bytes/sec
1 minute input rate 485 pkts/sec, 537048 bytes/sec
1 minute output rate 395 pkts/sec, 54546 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 485 pkts/sec, 511723 bytes/sec
5 minute output rate 387 pkts/sec, 65495 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/1:
received (in 51433.570 secs):
7749780 packets1066328930 bytes
67 pkts/sec20064 bytes/sec
transmitted (in 51433.570 secs):
10653359 packets10552787020 bytes
40 pkts/sec205006 bytes/sec
1 minute input rate 419 pkts/sec, 59621 bytes/sec
1 minute output rate 480 pkts/sec, 533950 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 399 pkts/sec, 67618 bytes/sec
<--- More --->
5 minute output rate 482 pkts/sec, 511073 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/2:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/3:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
<--- More --->
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/4:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/5:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
<--- More --->
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/6:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/7:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
<--- More --->
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/0:
received (in 51435.510 secs):
18513901 packets11784250044 bytes
25 pkts/sec229023 bytes/sec
transmitted (in 51435.510 secs):
18207269 packets11641332179 bytes
19 pkts/sec226078 bytes/sec
1 minute input rate 891 pkts/sec, 595715 bytes/sec
1 minute output rate 863 pkts/sec, 588935 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 885 pkts/sec, 584035 bytes/sec
5 minute output rate 870 pkts/sec, 580393 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/1:
received (in 51436.010 secs):
18207323 packets11641364184 bytes
<--- More --->
19 pkts/sec226076 bytes/sec
transmitted (in 51436.010 secs):
18513954 packets11784281987 bytes
25 pkts/sec229022 bytes/sec
1 minute input rate 855 pkts/sec, 575808 bytes/sec
1 minute output rate 884 pkts/sec, 582339 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 869 pkts/sec, 578350 bytes/sec
5 minute output rate 883 pkts/sec, 581924 bytes/sec
5 minute drop rate, 0 pkts/sec
------------------ show perfmon ------------------
PERFMON STATS: Current Average
Xlates 0/s 0/s
Connections 17/s 6/s
TCP Conns 8/s 2/s
UDP Conns 7/s 2/s
URL Access 0/s 0/s
URL Server Req 0/s 0/s
TCP Fixup 0/s 0/s
TCP Intercept 0/s 0/s
HTTP Fixup 0/s 0/s
<--- More --->
FTP Fixup 0/s 0/s
AAA Authen 0/s 0/s
AAA Author 0/s 0/s
AAA Account 0/s 0/s
------------------ show counters ------------------
Protocol Counter Value Context
IP IN_PKTS 168960 Summary
IP OUT_PKTS 169304 Summary
IP TO_ARP 61 Summary
------------------ show history ------------------
------------------ show firewall ------------------
Firewall mode: Transparent
------------------ show running-config ------------------
<--- More --->
: Saved
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
enable password
names
interface Vlan1
nameif inside
security-level 100
interface Vlan2
nameif outside
security-level 0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
<--- More --->
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd
regex domain1 ".facebook\.com"
regex domain2 ".fb\.com"
regex domain3 ".youtube\.com"
ftp mode passive
access-list ACL_IN extended permit ip any any
pager lines 24
mtu inside 1500
mtu outside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
<--- More --->
arp timeout 14400
access-group ACL_IN in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domain1
match regex domain2
match regex domain3
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
<--- More --->
message-length maximum 512
match domain-name regex class DomainBlockList
drop-connection log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:bb5115ea1d14ee42e7961ef0c9aaed86
: end
<--- More --->
------------------ show startup-config errors ------------------
INFO: No configuration errors
------------------ console logs ------------------
Message #1 : Message #2 : Message #3 : Message #4 : Message #5 : Message #6 : Message #7 : Message #8 : Message #9 : Message #10 : Message #11 : Message #12 : Message #13 : Message #14 :
Total SSMs found: 0
Message #15 :
Total NICs found: 10
Message #16 : 88E6095 rev 2 Gigabit Ethernet @ index 09Message #17 : MAC: 0000.0003.0002
Message #18 : 88E6095 rev 2 Ethernet @ index 08Message #19 : MAC: 001f.9ee8.ffa1
Message #20 : 88E6095 rev 2 Ethernet @ index 07Message #21 : MAC: 001f.9ee8.ffa0
Message #22 : 88E6095 rev 2 Ethernet @ index 06Message #23 : MAC: 001f.9ee8.ff9f
Message #24 : 88E6095 rev 2 Ethernet @ index 05Message #25 : MAC: 001f.9ee8.ff9e
Message #26 : 88E6095 rev 2 Ethernet @ index 04Message #27 : MAC: 001f.9ee8.ff9d
Message #28 : 88E6095 rev 2 Ethernet @ index 03Message #29 : MAC: 001f.9ee8.ff9c
Message #30 : 88E6095 rev 2 Ethernet @ index 02Message #31 : MAC: 001f.9ee8.ff9b
Message #32 : 88E6095 rev 2 Ethernet @ index 01Message #33 : MAC: 001f.9ee8.ff9a
Message #34 : y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: 001f.9ee8.ffa2
Message #35 :
Licensed features for this platform:
Message #36 : Maximum Physical Interfaces : 8
<--- More --->
Message #37 : VLANs : 3, DMZ Restricted
Message #38 : Inside Hosts : Unlimited
Message #39 : Failover : Disabled
Message #40 : VPN-DES : Enabled
Message #41 : VPN-3DES-AES : Enabled
Message #42 : VPN Peers : 10
Message #43 : WebVPN Peers : 2
Message #44 : Dual ISPs : Disabled
Message #45 : VLAN Trunk Ports : 0
Message #46 :
This platform has a Base license.
Message #47 :
Message #48 : Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Message #49 : Boot microcode : CNlite-MC-Boot-Cisco-1.2
Message #50 : SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
Message #51 : IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
Message #52 : --------------------------------------------------------------------------
Message #53 : . .
Message #54 : | |
Message #55 : ||| |||
Message #56 : .|| ||. .|| ||.
Message #57 : .:||| | |||:..:||| | |||:.
Message #58 : C i s c o S y s t e m s
Message #59 : --------------------------------------------------------------------------
<--- More --->
Message #60 :
Cisco Adaptive Security Appliance Software Version 7.2(3)
Message #61 :
Message #62 : ****************************** Warning *******************************
Message #63 : This product contains cryptographic features and is
Message #64 : subject to United States and local country laws
Message #65 : governing, import, export, transfer, and use.
Message #66 : Delivery of Cisco cryptographic products does not
Message #67 : imply third-party authority to import, export,
Message #68 : distribute, or use encryption. Importers, exporters,
Message #69 : distributors and users are responsible for compliance
Message #70 : with U.S. and local country laws. By using this
Message #71 : product you agree to comply with applicable laws and
Message #72 : regulations. If you are unable to comply with U.S.
Message #73 : and local laws, return the enclosed items immediately.
Message #74 :
Message #75 : A summary of U.S. laws governing Cisco cryptographic
Message #76 : products may be found at:
Message #77 : http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
Message #78 :
Message #79 : If you require further assistance please contact us by
Message #80 : sending email to [email protected].
Message #81 : ******************************* Warning *******************************
Message #82 :
<--- More --->
Message #83 : Copyright (c) 1996-2007 by Cisco Systems, Inc.
Message #84 : Restricted Rights Legend
Message #85 : Use, duplication, or disclosure by the Government is
Message #86 : subject to restrictions as set forth in subparagraph
Message #87 : (c) of the Commercial Computer Software - Restricted
Message #88 : Rights clause at FAR sec. 52.227-19 and subparagraph
Message #89 : (c) (1) (ii) of the Rights in Technical Data and Computer
Message #90 : Software clause at DFARS sec. 252.227-7013.
Message #91 : Cisco Systems, Inc.
Message #92 : 170 West Tasman Drive
Message #93 : San Jose, California 95134-1706
ciscoasa# -
Cisco ASA 5505 doesn't forware incoming connection to LAN
Hello everybody.
I just got a Cisco asa 5505 with the next OS and ASDM info
ASA 5505 OS 8.4(3) ASDM 6.47
I configured and enter all rules to allow incoming traffic to LAN but it's not working also, I have one host inside that is configured in a second IP and create the rule to allow traffic to it but it doesn't work too.
Problem 1
I have VNC running in port 5900 tcp and I want to connect from Internet using port 6001 and this has to forware the connection to the real VNC port. In the configuration I have a few host with the same configuration but I use different outside port to get it.
Problem 2.
I have a second IP with services: SMTP, HTTP, HTTPS and port 444 all TCP forwarding to a server in the LAN.
Facts:
SMTP.
Every time that I do telnet to the second IP looking for the SMTP port, the firewall doesn't let the incoming connection goes through and the LOGGING screen doesn't how that connection.
PORT 6001 (outside)
this port is configured to work with the IP in the outside internface and it was to send the incoming connection to a host inside to the real port 5900.
Can any one check my configuration if I'm missing anything? for sure I'm but I didn't find it. Bellow is the configuration, I masked the Public IPs just left the last number in the IP, also I left the LAN network to see better the configuration.
I will appreciate any help.
Thanks a lot..
CONFIGURATION.
: Saved
ASA Version 8.4(3)
hostname saturn1
domain-name mydominio.com
enable password SOMEPASS encrypted
passwd SOMEPASS encrypted
names
name 192.168.250.11 CAPITOLA-LAN
name 192.168.250.15 OBIi110-LAN
name 192.168.250.21 DRP1260-LAN
name 192.168.250.22 HPOJ8500-LAN
name 192.168.250.30 AP-W77-NG-LAN
name 192.168.250.97 AJ-DTOP-PC-LAN
name 192.168.250.96 SWEETHEART-PC-LAN
name 192.168.250.94 KIDS-PC-LAN
name XX.YY.ZZ.250 EXTERNALIP
name XX.YY.ZZ.251 EXTERNALIP2
name XX.YY.ZZ.1 GTWAY
dns-guard
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.250.2 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address EXTERNALIP 255.255.255.0
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name mydominio.com
object network CAPITOLA-LAN
host 192.168.250.11
object network EXTERNALIP
host XX.YY.ZZ.250
description Created during name migration
object network CAPITOLA-PUBLIC
host XX.YY.ZZ.251
object network capitola-int
host 192.168.250.11
object network capitola-int-vnc
host 192.168.250.11
object network aj-dtop-int-vnc
host 192.168.250.97
object network sweetheart-int-vnc
host 192.168.250.96
object network kids-int-vnc
host 192.168.250.94
object network VPNNetwork
subnet 10.10.20.0 255.255.255.0
object network InsideNetwork
subnet 192.168.250.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network capitola-int-smtp
host 192.168.250.11
object-group service capitola-int-smtp-service tcp
port-object eq smtp
object-group service capitola-int-services tcp
port-object eq smtp
port-object eq https
port-object eq www
port-object eq 444
object-group service capitola-int-vnc-service tcp
port-object eq 6001
object-group service aj-dtop-int-vnc-service tcp
port-object eq 6002
object-group service sweetheart-int-vnc-service tcp
port-object eq 6003
object-group service kids-int-vnc-service tcp
port-object eq 6004
access-list incoming extended permit icmp any any
access-list incoming extended permit tcp any object capitola-int object-group capitola-int-services
access-list incoming extended permit tcp any object capitola-int-vnc object-group capitola-int-vnc-service
access-list incoming extended permit tcp any object aj-dtop-int-vnc object-group aj-dtop-int-vnc-service
access-list incoming extended permit tcp any object sweetheart-int-vnc object-group sweetheart-int-vnc-service
access-list incoming extended permit tcp any object kids-int-vnc object-group kids-int-vnc-service
access-list incoming extended permit tcp any object capitola-int-smtp object-group capitola-int-smtp-service
access-list split-tunnel standard permit 192.168.250.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any object VPNNetwork
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpnpool 10.10.20.1-10.10.20.50 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static any any destination static VPNNetwork VPNNetwork no-proxy-arp
object network capitola-int
nat (any,any) static XX.YY.ZZ.251
object network capitola-int-vnc
nat (inside,outside) static interface service tcp 5900 6001
object network aj-dtop-int-vnc
nat (inside,outside) static interface service tcp 5900 6002
object network sweetheart-int-vnc
nat (inside,outside) static interface service tcp 5900 6003
object network kids-int-vnc
nat (inside,outside) static interface service tcp 5900 6004
object network obj_any
nat (inside,outside) dynamic interface
object network capitola-int-smtp
nat (any,outside) static interface service tcp smtp smtp
access-group incoming in interface outside
route outside 0.0.0.0 0.0.0.0 GTWAY 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
http server enable
http server idle-timeout 2
http server session-timeout 1
http 192.168.1.0 255.255.255.0 inside
http CAPITOLA-LAN 255.255.255.255 inside
http AJ-DTOP-PC-LAN 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh CAPITOLA-LAN 255.255.255.255 inside
ssh AJ-DTOP-PC-LAN 255.255.255.255 inside
ssh timeout 15
console timeout 0
vpn-addr-assign local reuse-delay 2
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username admin password SOMEPASS encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect pptp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:036b82d3eb5cffc1c65a3b381246d043
: end
asdm image disk0:/asdm-647.bin
no asdm history enableJose, your fix to problem 1 allows all access from the outside, assuming you applied the extended list to the outside interface. Try to be more restrictive than an '...ip any any' rule for outside_in connections. For instance, this is what I have for incoming VOIP (access list and nat rules):
access list rule:
access-list outside_access_in extended permit udp any object server range 9000 9049 log errors
nat rule:
nat (inside,outside) source static server interface service voip-range voip-range
- 'server' is a network object *
- 'voip-range' is a service group range
I'd assume you can do something similar here in combination with my earlier comment:
access-list incoming extended permit tcp any any eq 5900
Can you explain your forwarding methodology a little more? I'm by no means an expert on forwarding, but the way I read what you're trying to do is that you have an inbound VNC request coming in on 5900 and you want the firewall to figure out which host the request should go to. Or is it vice-versa, the inbound VNC request can be on port 6001-6004 ? -
Cisco ASA 5505 - 2 PPPoE connection
Hi,
Please I would be very pleased if someone could give me a hand in this matter.
I have a Cisco ASA 5505 9.0(2), 2 dial-up connection (ADSL) with fix IP from the same ISP. I have 2 Linksys router (each dial-up has a router) as well. Both Linksys are connected directly to ASA configured in bridge mode.
I set up one dial-up on interface called “outside” with PPPoE configuration which is, in fact, up and running. I’m able to get my fix public IP.
My problem come from when I try to set up the second dial-up on interface called “outside-other”. I configure properly all PPPoE parameters however I’m not able to get my second fix public IP. Somehow, it’s not able to establish a connection with the ISP. (PPPoE session has not been established yet)
This could be useful information: the PPPoE Username is the same in both dial-up connection (given by my ISP).
I hope someone can shed light on this issue.
Thanks in advance,
Apologies for my lack of awareness.
AntonioHi,
This is my schema:
connection A ( interface outside) --> DSL --> Router Linksys mode bridge --> Cisco ASA , up and running with IP fix.
connection B ( interface outside-other) --> DSL --> Router Linksys mode bridge --> Cisco ASA, down : Status PADR_SENT
I tried to use two different VPDN_groups for the two connections A and B. However, B is still not working. Just one of them is able to get IP from ISP, connection A.
When I set up the Linksys router (connection B) in PPPoE, the connection works and get an IP fix from ISP.
What I want to do is set up a VPN on connection B so I need to configure this second dial-up on Cisco ASA. I cannot use connection A due to security reasons.
Thanks -
Connecting Cisco VPN client v5 to asa 5505
I am having problem configuring remote vpn between ASA5505 and Cisco VPN client v5. I can successfully establish connection between ASA and Vpn client and receive IP address from ASA. VPN client statistics windows shows that packets are send and encrypted but none of the packets is Received/Decrypted.
Can not ping asa 5505
Any ideas on what I have missed?Your NAT configuration is incomplete, enter the following commands to your configuration:
access-list nonat extended permit ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
nat (inside) 0 access-list nonat
This tells the ASA that the traffic destined for the VPN Client should not be NATted and should be sent directly to the client via the VPN Tunnel!
Please rate if the post helps!
Regards,
Michael -
Cisco ASA 5505 Remote Access IP/Sec VPN Connectivity Issues
We have a Cisco ASA that we use just for Remote Access VPN. It uses UDP and was working fine for about 2 months. Recently clients have had intermittent issues when connecting from home. The following message is display by the Cisco VPN Client :
"Secure VPN connection terminated locally by the Client. Reason 412: The remote peer is no longer responding"
Upon looking at a client side packet capture, I notice that no response is being given back to the client for the udp packets sent to the ASA on udp 500. If I login to the ASA from the LAN and send a single ping FROM the ASA, then the client can connect without issue. I don't understand the significance of the needed outbound ping since ping is not used by the client to test if the ASA is alive.
Once again this is a remote access udp ip/sec VPN. I set most of it up with the VPN wizard and then backed up the config. The issue started happening at least a month after setup (maybe two) and I restored to the saved config just in-case, but the issue remains.
Any insight would be greatly appreciated.
I'm using IOS 831 and have tried 821 and 823 as one thread that I found recommended downgraded to 821.
Thanks much,
JustinJavier,
I logged into the ASA last time the VPN went down. I issued the following commands:
debug crypto isakmp 190
debug crypto ipsec 190
capture outside-cap interface outside match udp any any
I then used a remote access tool to access the client and tried to connect. I got absolutely nothing from debugging. So I issued the following command:
show capture outside | include 500
and also got nothing. So I issued the following command:
ping 4.2.2.2
Upon which my normal deug messaged began to showup, so I issued the show capture outside command again and recieved the expected output below:
1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 868
2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 444
3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 172
4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 60
8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 204
9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 252
11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 868
12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 444
13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 172
14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 204
19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 252
20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 1036
21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 188
23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 100
174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 500
377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000: udp 100 1: 15:44:18.570160 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 868
2: 15:44:18.579269 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 444
3: 15:44:18.703866 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 172
4: 15:44:18.706567 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
5: 15:44:18.831499 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
6: 15:44:19.024061 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 76
7: 15:44:19.111963 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 60
8: 15:44:19.517185 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 204
9: 15:44:19.521350 802.1Q vlan#2 P0 REMOTE_IP.1151 > OFFICE_IP.500: udp 92
10: 15:44:19.522723 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1151: udp 252
11: 15:44:42.121957 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 868
12: 15:44:42.130822 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 444
13: 15:44:42.228397 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 172
14: 15:44:42.231036 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
15: 15:44:42.329557 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
16: 15:44:42.521091 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 76
17: 15:44:42.610167 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
18: 15:44:42.649258 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 204
19: 15:44:42.653790 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 252
20: 15:44:42.789342 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 1036
21: 15:44:42.792119 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
22: 15:44:42.800846 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 188
23: 15:44:42.892120 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 60
34: 15:44:54.446220 802.1Q vlan#2 P0 REMOTE_IP.1155 > OFFICE_IP.500: udp 92
35: 15:44:54.447913 802.1Q vlan#2 P0 OFFICE_IP.500 > REMOTE_IP.1155: udp 92
70: 15:45:01.825000 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 100
174: 15:45:03.417764 802.1Q vlan#2 P0 OFFICE_IP.10000 > REMOTE_IP.10000: udp 500
377: 15:45:07.881500 802.1Q vlan#2 P0 REMOTE_IP.10000 > OFFICE_IP.10000: udp 100
It would seem as if no traffic reached the ASA until some outbound traffic to an arbitrary public IP. In this case I sent an echo request to a public DNS server. It seems almost like a state-table issue although I don't know how ICMP ties in.
Once again, any insight would be greatly appreciated.
Thanks,
Justin -
Cisco ASA 5505 - Keeps dropping internet connection
Hi,
We are having some issues with our Cisco ASA 5505 unit, it intermittently drops the outside interface connection. Internally the network appears to be working correctly with no issues. Even though the outside interface indicates it is 'up' access to the internet is lost from our LAN. This seems to be ocourring more and more often! This is happening for all users on the network too. Reloading the ASA seems to correct the problem temporally but this isn't really an option during peak periods in the day as this would obviously hinder work being carried out by employees.
Any ideas?
Any help would be greatly appreciated!!
Thanks,
John
Running Config Below:
ASA Version 8.2(1)
hostname ******************
domain-name *************************
enable password ************************* encrypted
passwd **************************** encrypted
names
dns-guard
interface Vlan1
nameif inside
security-level 100
ip address 10.3.0.254 255.255.0.0
interface Vlan2
nameif outside
security-level 0
ip address ***************** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server *****************
domain-name **********************
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list outside_access_in extended permit tcp any any eq smtp
access-list outside_access_in extended permit tcp any any eq 3389
access-list outside_access_in extended permit tcp any any eq https
access-list outside_access_in extended permit tcp any any
access-list outside_access_in extended permit tcp any any eq 3839
pager lines 24
logging enable
logging asdm warnings
mtu inside 1500
mtu outside 1500
failover timeout -1
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp 10.3.0.2 smtp netmask 255.255.255.255
static (inside,outside) tcp interface https 10.3.0.2 https netmask 255.255.255.255
static (inside,outside) tcp interface 3839 10.3.0.1 3839 netmask 255.255.255.255
static (inside,outside) tcp interface 3389 10.3.0.1 3389 netmask 255.255.255.255
static (inside,inside) 10.3.0.0 10.3.0.0 netmask 255.255.0.0 norandomseq nailed
static (inside,inside) 172.16.63.0 172.16.63.0 netmask 255.255.255.240 norandomseq nailed
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 *************** 1
route inside 172.16.63.0 255.255.255.240 10.3.0.253 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.3.0.0 255.255.0.0 inside
http 10.3.0.0 255.255.255.0 inside
http 10.10.2.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt noproxyarp inside
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 1
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
username ************ password *********************** encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy globalHello,
What happens when you assign eth0 as internal interface and eth1 as outside if?
Also configure logging (/debugging) to see if there are hardware issues or something else.
And it seems you have a range of public addresses. What happens when you connect a device, e.g. a laptop directly on the internet access device and send continue ping to an internet host.
When you loose internet connectivity, is the laptop still pinging to that host?
Hopefully this helps you,
Kind regards,
Ralph Willemsen
Arnhem, Netherlands -
How can I debug VPN connections on a Cisco ASA?
Hi,
I have a Cisco ASA and I am trying to get a Cisco 877 DSL router connected to it using the ASDM VPN wizard, but can't.
I have just had the 877 DSL router connect to my Cisco Concentrator and have simlpy changed the peer address on the router to now point to the ASA's external IP instead of the Concentrator. The Concentrator is good because I like it's real-time event viewer and it can tell me if the Concentrator is even seeing the connection attempt, but how can I dall this on the ASA?
Thanksshow isa sa
- that will show the status of phase 1
show cry ipsec sa
- that will show the status of phase 2, as well as number of encrypted/decrypted packets -
Unable to access cisco asa via https or asdm!! connection interrupted message appears on the browser
Hey guys,
I am unable to access cisco asa device using https and cannot lunch asdm, after recent power failure at our location. I have asdm installed on my machine and whenever i try to access the asdm, receive Error: unable to lunch device manager from X.X.X.X The following is log from java console
Trying for ASDM version file; url = https://x.x.x.x/admin/
javax.net.ssl.SSLHandshakeException: Remote host closed connection during handshake
When i try to access it from the browser it show error message
"The connection was interrupted"
I am running CISCO ASA 8.3 (1)
with asdm image as asdm 7.1.3
JAVA version installed Java 7 update 71
I have added the https:> to exception site list and set security level to medium,
even ssh access is not working !!
I would appreciate if anyone can help me out!!
Thanks
FareedHey lcaruso,
thanks for information!!
i was able to connection through console as suggested and regenerated the rsa key .. was able to connection through ssh, but the issue with the asdm or web access was not resolved.
I have tried few of the steps as suggested on
https://supportforums.cisco.com/document/49741/asa-pixfwsm-unable-manage-unit-sshtelnetasdm#collect_captures
capture output
ZHHFP-FIREWALL1(config)# sh cap capin
139 packets captured
1: 18:50:17.654720 802.1Q vlan#1 P0 192.168.160.113.58084 > 192.168.160.126.8
443: S 2567327150:2567327150(0) win 8192 <mss 1260,nop,wscale 8,nop,nop,sackOK>
2: 18:50:17.654812 802.1Q vlan#1 P0 192.168.160.126.8443 > 192.168.160.113.58
084: S 590825877:590825877(0) ack 2567327151 win 8192 <mss 1380>
3: 18:50:17.655621 802.1Q vlan#1 P0 192.168.160.113.58084 > 192.168.160.126.8
443: . ack 590825878 win 65520
4: 18:50:17.656078 802.1Q vlan#1 P0 192.168.160.113.58084 > 192.168.160.126.8
443: P 2567327151:2567327332(181) ack 590825878 win 65520
5: 18:50:17.656139 802.1Q vlan#1 P0 192.168.160.126.8443 > 192.168.160.113.58
084: . ack 2567327332 win 8192
6: 18:50:17.656475 802.1Q vlan#1 P0 192.168.160.126.8443 > 192.168.160.113.58
084: FP 590825878:590825878(0) ack 2567327332 win 8192
7: 18:50:17.657696 802.1Q vlan#1 P0 192.168.160.113.58084 > 192.168.160.126.8
443: . ack 590825879 win 65520
8: 18:50:17.657802 802.1Q vlan#1 P0 192.168.160.113.58084 > 192.168.160.126.8
443: F 2567327332:2567327332(0) ack 590825879 win 65520
9: 18:50:17.657848 802.1Q vlan#1 P0 192.168.160.126.8443 > 192.168.160.113.58
084: . ack 2567327333 win 8192
10: 18:50:17.658108 802.1Q vlan#1 P0 192.168.160.113.58085 > 192.168.160.126.8
443: S 1351758892:1351758892(0) win 8192 <mss 1260,nop,wscale 8,nop,nop,sackOK>
also i have downgraded the java to 1.6_45 but still not luck.
error message i received on java console
Trying for IDM. url=https://x.x.x.x/idm/idm.jnlp/
javax.net.ssl.SSLHandshakeException: Remote host closed connection during handshake
at sun.security.ssl.SSLSocketImpl.readRecord(Unknown Source)
at sun.security.ssl.SSLSocketImpl.performInitialHandshake(Unknown Source)
at sun.security.ssl.SSLSocketImpl.startHandshake(Unknown Source)
at sun.security.ssl.SSLSocketImpl.startHandshake(Unknown Source)
at sun.net.www.protocol.https.HttpsClient.afterConnect(Unknown Source)
at sun.net.www.protocol.https.AbstractDelegateHttpsURLConnection.connect(Unknown Source)
at sun.net.www.protocol.http.HttpURLConnection.getInputStream(Unknown Source)
at sun.net.www.protocol.https.HttpsURLConnectionImpl.getInputStream(Unknown Source)
at com.cisco.launcher.w.a(Unknown Source)
at com.cisco.launcher.s.for(Unknown Source)
at com.cisco.launcher.s.new(Unknown Source)
at com.cisco.launcher.s.access$000(Unknown Source)
at com.cisco.launcher.s$2.a(Unknown Source)
at com.cisco.launcher.g$2.run(Unknown Source)
at java.lang.Thread.run(Unknown Source)
Caused by: java.io.EOFException: SSL peer shut down incorrectly
at sun.security.ssl.InputRecord.read(Unknown Source)
... 15 more
Any help would be highly appreciated!!
Thanks
Fareed
Maybe you are looking for
-
How can I see the photo quality settings in iLife'06 books
I assembled a 100 page book using iLife'05 over the last week or so. Luckily I hadn't ordered the book before learning about the new "improved print quality" when using iLife'06. Well, iLife'06 finally arrived today and I installed it and... Well, do
-
Receiving a false paper jam error message for a 6310 all in one printer
I have an hp 6310 all in one printer. It is showing a false paper jam error message with no paper in the printer. I have tried all of the fixes that have been suggested on the website as well as on you tube to no avail. Nothing works, I have clea
-
I want to adjust improt queue for a single request in PRD but when i press the zikzak symbol , It says transfer transport files for 61 transport request from import queue.As per my knowldge adjust of import queue for more then one request is not an i
-
Need help finishing download of Acrobat 7
Was told back in Oct. 2014 that older versions of Adobe were/would be free. I just tried to download Acrobat 7 and I am getting a window asking me for a serial number. I don't have one, since I did not purchase this version. Please advise. Thanks
-
hey is it possible to make an accordion tab a link like on the collapsible panels? i mean do something like this: <div class="AccordionPanel"> <div class="AccordionPanelTab"><a href="some url">Tab 1</a></div> </div> like on the collapsible panels i d