Connection problem local files on NAS

My local files in DW CS5 are stored on a Qnap NAS,
when I want to upload the files to the remote site,
most of the time it works, but I got a lot connection time-outs......
Background activity
Waiting for server........
my computer setup,
Qnap 239 pro, Draytek router, Imac, CS5 Dreamweaver
Any sugestion? thanks

The problem isn't with your NAS, it is in fact Dreamweaver. This has been a consistent issue since CS3 and Adobe has failed to really address it, unfortunately.
In the Dreamweaver dialog for managing your site (and depending on which version of CS you're using) there will be the following options for the FTP server connection:
Use Passive FTP - usually checked if you're behind a firewall/router - and this is usually the main culprit of this 'waiting for server' issue, I've found.
Use IPV6 Transfer Mode - this uses IPv6 connections and lookups and does little to actually improve performance in IPv4 networks, usually checked for the performance gains in true IPv6 connections (still rare as of this writing).
Use Proxy - as defined for your browser preferences, typically. Only checked if you're using a proxy. If you don't know what a proxy is, you're unlikely to be using one, but you can check your browsers proxy settings to see if it has any enabled by your ISP and check this box if it does.
Use FTP Performance Optimization - this basically turns on NOOPs - allowing DW to send NOOP commands to your FTP server to maintain the connection. Usually checked unless you cannot connect to your server with it checked (some servers do not support keep-alive's)
Use Alternative FTP Move Method - Frankly, I have no idea what this does as I've never had to use it. I do know it does not solve the 'waiting for server' issue, however, through trial and error.
And yes, Filezilla is so supremely good at FTP it makes DW look slow even when it's working correctly.
This is definitely a strategy I hope Adobe adopts - removing all the clutter from the FTP algorithms in Dreamweaver. All we need is simply FTP typically. I understand it's tied into RDS and everything else - but I hope Adobe unties it so FTP, which is still the most widely used protocol for updating remote server files from Dreamweaver, no longer has these unneccesary delays.
Hope that helps. Try passive FTP first - like I said, 9 times out of 10 - that's the problem (I could go into the details of why this occurs and why one solution is to set-up port forwarding on your router, but I won't )

Similar Messages

  • CS3 / Vista / local files on NAS - DW crawls and is unuseable

    Subject pretty much says it all.
    DW CS3 on a Vista laptop.  My development cfm files are on a NAS mapped as Y:\Sites\[sitename].  I primarily use this laptop for quick fixes but that came screeching to a halt today.
    I opened up a site and told it to sync via ftp to the remote server.  After about 4 minutes it told me there were 10 small files to sync.  Syncing took almost 10 minutes.  (no, it was not the remote server being slow).
    When I opened a file locally from the Y drive to edit it, it was extremely slow in code view.  Copy / Paste took 30 seconds to complete.  Even scrolling the page up and down in DW had severe delays.
    I did a bunch of Google searching on it and found many people with this problem back to the CS version, but no real answer to it.  The NAS drive is fine and even Windows Explorer is quick bringing it up and moving files around.  This isn't a huge site - maybe 100 cfm templates and none of the pages are hugely complex.
    No other software on this laptop has any problems accessing the NAS - MySQL, PS, Office etc.
    Any ideas where to look for a patch or setting that can help this behavior?

    I've never used a NAS, but can you use a UNC path? If so, any difference in performance?
    I have two Vista boxes on this little network and they both take a long time to connect to drives on other computers. Once connected, they transfer files over the local network at expected speeds, though. I don't use DW's FTP, but I could test that later if needed (CS3 on Vista Home Premium, DW8 on Vista Ultimate).
    Mark A. Boyd
    Keep-On-Learnin' :-)
    This message was processed and edited by Jive.
    It shall not be considered an accurate representation of my words.
    It might not even have been intended as a reply to your message.

  • Is it possible to connect a local file server to 365 onedrive via sharepoint?

    We have our local 2012 file server with everyones document directories and common shares. We use AD and have all user accounts defined. As part of our K12 licensing we have Office 365 E1 for all staff, so I set up the Azure AD Sync and we now have all the
    staff accounts set up in 365 and people can work on Office from home.
    The problem is that everyone wants their files from home as well, ideally in their OneDrive. OneDrive for Business doesn't seem to have a mechanism to sync all the files from our file server to each persons OneDrive automatically. I read somewhere that I
    can do it by using SharePoint as a intermediary - that is I can set up a local sharepoint that syncs the fileserver to sharepoint, then I can set up the 365 sharepoint to sync between the onprem sharepoint and the 365 OneDrives.
    This seems like a massive pain but is it doable? is there a better way or is it not possible and sharepoint/local files will always be separate from Onedrive?  it seems like such a common and obvious request for people who can't dump local file servers.
    Mark

    not all to each, just duplicating our current system. Each user has a few hundred mb of files (on average) and there is a common drive with a few hundred gb.
    Right now the assumption by Microsoft is that each user will individually install the local Onedrive app and sync their C: drive documents folder to their Onedrive. In our case we have the documents stored centrally and the onedrive app will not sync a network
    folder. I am looking for some method of making it happen.

  • DW CS3 MySql Connect Problems Local Mac

    Hi,
    I switched from CS2 to CS3, somewhere along the way I can no
    longer connect to MySql doing local testing. I know the MySql
    server works as I can connect to it and work with tables etc with
    Navicat.
    I keep getting:
    Warning: mysql_pconnect() [function.mysql-pconnect]: Can't
    connect to local MySQL server through socket
    '/var/mysql/mysql.sock' (2) in
    /Users/Rich/Sites/Site/htdocs/Connections/Main.php on line 9
    Fatal error: Can't connect to local MySQL server through
    socket '/var/mysql/mysql.sock' (2) in
    /Users/Rich/Sites/Site/htdocs/Connections/Main.php on line 9
    Anybody got any ideas?
    Thanks
    Rich

    I'm running 10.5.8 so this may be completely the wrong answer...
    Have you set the privileges on the MySQL user on the server database to allow a connection from a remote client IP Address?
    You can do this via phpMyAdmin user privileges or as a MySQL command, something like
    GRANT SELECT ON <database>.<table>
    TO <user>@'<IP address of client>'
    IDENTIFIED BY "<password>";
    The IP address can contain a wild character, e.g. 192.168.1.%
    john

  • Local Files are deleted upon disconnecting from project

    Running Version Cue CS3 3.1.0 with latest Bridge. (PowerMac G5 - OSX 10.4.11)
    Im running the VC server on my local machine. Intention is for only myself to use it for version control.
    I created a project, added my files... the standard local file path is ~/Documents/Version Cue/projectname
    2 issues, perhaps the same issue
    whenever i attempt to disconnect from the project... the local files are deleted...
    so, if i had set a custom path for my projects local files, VC immediately deletes the files, and next time trying to connect, the local file path is reset to the ~/Documents/Version Cue/projectname
    Is this how VC is supposed to function?
    Any help or insight is greatly appreciated!!! Thank you in advance

    Running Version Cue CS3 3.1.0 with latest Bridge. (PowerMac G5 - OSX 10.4.11)
    Im running the VC server on my local machine. Intention is for only myself to use it for version control.
    I created a project, added my files... the standard local file path is ~/Documents/Version Cue/projectname
    2 issues, perhaps the same issue
    whenever i attempt to disconnect from the project... the local files are deleted...
    so, if i had set a custom path for my projects local files, VC immediately deletes the files, and next time trying to connect, the local file path is reset to the ~/Documents/Version Cue/projectname
    Is this how VC is supposed to function?
    Any help or insight is greatly appreciated!!! Thank you in advance

  • MySQL problem -- ERROR 2002 Can't connect to local MySQL server

    Not Sure if this would be a right forum for my problem...
    I'm installing mySQL on my iBook, and thought that I have configured it. But then, after followring some instuctions from Adobe and Marc Liyanage sites, I have a problem to connect. This is what I've done in "TERMINAL"
    ~username$> cd /usr/local/mysql
    mysql ~username$> sudo chown -R mysql data/
    (asking for admin password)
    mysql ~username$> sudo echo
    mysql ~username$> sudo ./bin/mysqld_safe &
    username-ibook-g4:/usr/local/mysql username$ Starting mysqld daemon with databases from /usr/local/mysql/data
    STOPPING server from pid file /usr/local/mysql/data/roshaili-osmans-ibook-g4.local.pid
    060611 16:31:30 mysqld ended
    mysql ~username> /usr/local/mysql/bin/mysql test
    ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/tmp/mysql.sock' (2)
    [1]+ Done sudo ./bin/mysqld_safe
    mysql ~username>
    When I typed ::
    /usr/local/mysql/bin/mysqladmin -u root
    (see that there's no password)
    Then it displays:
    /usr/local/mysql/bin/mysqladmin Ver 8.41 Distrib 5.0.22, for apple-darwin8.6.0 on powerpc
    Copyright (C) 2000 MySQL AB & MySQL Finland AB & TCX DataKonsult AB
    This software comes with ABSOLUTELY NO WARRANTY. This is free software,
    and you are welcome to modify and redistribute it under the GPL license
    Administration program for the mysqld daemon.
    Usage: /usr/local/mysql/bin/mysqladmin [OPTIONS] command command....
    -c, --count=# Number of iterations to make. This works with -i
    (--sleep) only.
    ...... bla bla bla.....
    Variables (--variable-name=value)
    and boolean options {FALSE|TRUE} Value (after reading options)
    count 0
    force FALSE
    compress FALSE
    character-sets-dir (No default value)
    default-character-set (No default value)
    host (No default value)
    port 0
    .........bla bla....
    ping Check if mysqld is alive
    processlist Show list of active threads in server
    reload Reload grant tables
    refresh Flush all tables and close and open logfiles
    shutdown Take server down
    status Gives a short status message from the server
    start-slave Start slave
    stop-slave Stop slave
    variables Prints variables available
    version Get version info from server
    roshaili-osmans-ibook-g4:~ roshailiosman$ >
    -----------------finish-----------------
    Does that mean that I'm connected to mySQL?
    Does anybody how to connect to MYSQL from the terminal? Thanks.
    iMac Mac OS X (10.4.6)
    iMac   Mac OS X (10.4.6)  

    Your biggest 'issue' right now is that your mysqld process is stopping on you -- making a connection impossible.
    Why it's bombing might be in a log .. try in mysql/data/usr.local.err .. and fix why itsbombing.
    To connect to it it'll be : mysql -u root -ppassword -D database

  • Problem with File panel and Local files

    I am having a couple of problem using Dreamweaver  (which may be related) and can’t find any appropriate help on the web site.
    I have created a small website and have it up and running.    I’m now trying to do some minor modifications.     But Dreamweaver seems to have lost the address of my local files on my home computer (although files are still there in the same place.)      In the on-line training material it shows how to define where the root directory is when you start developing a site,  but I can’t find where these setting are so I can check and if nessessary amend them.   If I go to Define Site from the Site drop down options,  this does not allow me to check or define the root directory.
    Secondly,  in the File panel (lower right on the screen) the address bar at the top only shows the remote files and the icons to the right (“put”, “get”, etc) have disappeared and I can’t seem to get them back.   Also that lower panel seems to be floating rather than being fixed like it was.     I have tried clicking on Classic View in the Workspace layout options but this doesn’t move things back to how they were when I first started using Dreamweaver (just a few weeks ago).
    Can you offer any advice on what the problem is and how to manage it?  Many thanks.   I'm  using Dreamweaver CS4 and an iMac.

    Immediately below the Tabs saying "Files" and Assets" is a small box 
    with arrow on the right to show the drop down list.        In the box 
    on the right there's an icon of two networked computers.  Then it 
    says, "ftp://Hill farm Web Site"  which is the name of my website.     
    If I click on the arrows to pull up the drop-down box,  I get four 
    options divided by a line.   Above the line the options are Computer, 
    HD and ftp://Hill farm Web Site.  Below the line it says manage sites.
    Below this is list of files that make up my website in a directory 
    structure.   The header for the first column reads, "Local Files",  
    which appears to be untrue, because the top line in the directory 
    structure below reads,  "ftp://Hill farm Web Site".
    Does this help?
    regards
    David

  • Problem with iWeb 09, after the publication in a local file.

    *Subject: problem with iWeb 09, after the publication in a local file, i can't see my blog, nor my photos, but before that all was working fine.*
    After the publication in the local file, I see all my pages, but there is a mistake on the page "Blog" where I just can see the top of my page, it's cut and I can't see it entirely, so I can't see the inputs while I should see 3 news or 3 inputs. And it's the same for the "Photos" page where the page is cut, I can't see the photos, and it's just written : "Put the slide show and subscribe".To finish, when I want to activate the comments, it doesn't work neither.
    Please help me.

    I want to activate the comments, it doesn't work neither.
    The comments feature is only available when you publish to the MobileMe server, so I don't think you can use it when you publish to a local file.

  • Problem in ALV export to Excel (Local File)

    Hi guys,
    I'm using the option export data do local file, option excel, but some strange behave is happening...
    Some columns are exported without the last digit...
    Ideas?
    Regards,
    LMS

    Hi LMS,
    Use this link.
    Export to excel in ALV
    Problem with Export to Excel from ALV Grid
    Hope this will help you to resolve your problem.
    Regards,
    Vijay

  • Problem with Local File Identification in RFC

    Dear all,
    We are working on a scenario where we have to integrate an external application with SAP system. The external application would use SAP DMS as document repository; It will send us a local file path and we have to upload the document located in that path as an attachment to a DMS Document Info Record. We have designed a wrapper RFC for this purpose, which encapsulates the standard Fm BAPI_DOCUMENT_CREATE2. This BAPI takes a file path input under table parameter DOCUMENTFILES. Problem is, when we are running the RFC from SAP GUI, the document info record is created correctly with the document as attachment, but when we invoke the RFC from the external application, the process fails and we get an error message stating:"Error while checking in Original Files". We debugged the scenario and found out that, while running under SAP GUI, the BAPI is able to identify a GUI Link, and hence succeeds; but while calling from the external application, the BAPI fails to find a GUI Link, tries to start a FTP Server using RFC Destination SAPFTP, and fails. So, obviously, the BAPI is not able to parse the local file path because of non-existence of GUI Link. So,in this regard, my question is: is there no way that we can pass a local file path from an external application to SAP, and get the same identified and get the document uploaded? Is there any alternative to our approach?
    Awaiting answers.
    Regards,
    Sid

    Solved the problem by:
    Converting file content to binary->transferring binary content to a wrapper RFC->writing the content into a temporary file in application server->then calling BAPI_DOCUMENT_CREATE2 to create the document without attachment->then calling CVAPI_DOC_CHECKIN to checkin the temporay file from application server.
    Related references:
    http://wiki.sdn.sap.com/wiki/display/PLM/DMSandbackground+processing
    https://websmp130.sap-ag.de/sap/support/notes/504692
    How to upload file from Web Dynpro into R/3 (BAPI_DOCUMENT_CREATE2)
    Thanks to All who have contributed to the Solution.
    Sincere Regards,
    Sid

  • Save Grid Alv as Local File Problem

    Hi,
    The Alv output via REUSE_ALV_GRID_DISPLAY, when i export ALV to local file as Excel some cells are converted the value.
    Ex.
    06MAY51   " display as char on ALV, there is no problem, this value of a plaque of a vehicle
    06.May.51   " display as date on Excel, converts char to date, and the value is displaying as 06.05.1951 (date)
    i dont know this convertion happens.
    can somebody help me please?
    best regards
    Edited by: Rob Burbank on Jun 7, 2011 3:56 PM

    Hi,
    i opened the excel file in notepad and i saw the values are not converted. 06MAY51
    and i created a blank excel file then i entered this value into a blank cell then i saw the values are converted by the excel.
    so i think there is no problem in SAP.
    the another way is to display ALV as Excel in SAP using Excel button on ALV then save the Excel, but if the ALV have too much values, it is not working. it is waiting too much. it is trying to compile the ALV to Excel format.
    Thanks

  • Problem opening local files

    Hi!
    Our servlet has problems opening links to local files. The syntax of the link is correct (file:///program_install_folder/subFolder1/some_file.txt). When user copy-pastes the url to IE's address bar, the file opens without problems, but clicking the link does nothing.
    This has probably something to do with IE's security issues, but:
    1) is there any way to solve this problem with java?
    2) adding the site to trusted sites doesn't help, but is there any other settings which could enable user to open the link to local file?
    Requirement is that program works with Windows XP and IE6.

    servlets run on the server and
    cannot open local client files

  • Problem During reading and write local file

    Hi ,
    I had written a small applet program, it have function �readNwriteFile()� it read/write the local file
    This function works fine when I call it from start () function.
    But whenever I was trying to call this function from java script it gave me this exception.
    �java.security.AccessControlException: access denied (java.io.FilePermission C:\temp_jar\DSC01692.JPG read)�.
    Java script is working fine, I can access any another function from script The problem is some related to access
    I had set the permission in my policy file .this the permission that I had set.
    grant codebase "file:c:\temp_jar"{
    permission java.io.FilePermission "<< ALLFILES >> , "read ,write ,delete ,execute ";
    Java code.
    package com.ravindra;
    import javax.swing.*;
    import java.awt.*;
    import java.io.*;
    import java.util.*;
    public class MialTest extends JApplet{
         public void init() {
         public void start(){
              readNwriteFile(); /// When I call this function from here It is working
         public byte [] readNwriteFile(){
              try {
                   File localfile = null;
                   localfile = new File("C:\\temp_jar\\DSC01692.JPG");
                   FileInputStream fs = new FileInputStream(localfile);
                   ByteArrayOutputStream bs = new ByteArrayOutputStream() ;
                   int actual_data = (int)fs.read();
                   while(actual_data > -1){
                        bs.write(actual_data);
                        actual_data = (int)fs.read();
                   byte [] final_data = bs.toByteArray();
                   File out_file = new File("C:\\temp_jar\\Ravindra_test.JPG");
                   FileOutputStream out_stream = new FileOutputStream(out_file);
                   out_stream.write(final_data);
                   out_stream.flush();
                   fs.close();
                   bs.close();
                   localfile = null;fs = null; bs = null;
                   return final_data;
              } catch (Exception e) {
                   // TODO Auto-generated catch block
                   e.printStackTrace();
                   return null;
    Java Script Code:

    Hi ,
    I had written a small applet program, it have function �readNwriteFile()� it read/write the local file
    This function works fine when I call it from start () function.
    But whenever I was trying to call this function from java script it gave me this exception.
    �java.security.AccessControlException: access denied (java.io.FilePermission C:\temp_jar\DSC01692.JPG read)�.
    Java script is working fine, I can access any another function from script The problem is some related to access
    I had set the permission in my policy file .this the permission that I had set.
    grant codebase "file:c:\temp_jar"{
    permission java.io.FilePermission "<< ALLFILES >> , "read ,write ,delete ,execute ";
    Java code.
    package com.ravindra;
    import javax.swing.*;
    import java.awt.*;
    import java.io.*;
    import java.util.*;
    public class MialTest extends JApplet{
         public void init() {
         public void start(){
              readNwriteFile(); /// When I call this function from here It is working
         public byte [] readNwriteFile(){
              try {
                   File localfile = null;
                   localfile = new File("C:\\temp_jar\\DSC01692.JPG");
                   FileInputStream fs = new FileInputStream(localfile);
                   ByteArrayOutputStream bs = new ByteArrayOutputStream() ;
                   int actual_data = (int)fs.read();
                   while(actual_data > -1){
                        bs.write(actual_data);
                        actual_data = (int)fs.read();
                   byte [] final_data = bs.toByteArray();
                   File out_file = new File("C:\\temp_jar\\Ravindra_test.JPG");
                   FileOutputStream out_stream = new FileOutputStream(out_file);
                   out_stream.write(final_data);
                   out_stream.flush();
                   fs.close();
                   bs.close();
                   localfile = null;fs = null; bs = null;
                   return final_data;
              } catch (Exception e) {
                   // TODO Auto-generated catch block
                   e.printStackTrace();
                   return null;
    Java Script Code:

  • Xcelsius xml map connection error [local xml file]

    xcelsius 2008 SP1 (loaded by IT dept)
    I am having issues with an xml map connection after I export to flash. The xml data file is local so the URL is (C:\Documents and Settings\..\Desktop\file.xml). It works fine in preview. I reasearched the topic and it all points to flash security settings but how can that be since everything is local. I'm doing this on my computer an nothing else.
    Do i still need to change the flash security setting (crossdomain.xml) even when I am trying to access just local file? If so does that mean that I need to create one of these crossdomain files in my C: directory. Because that doesn't sound right.

    Thank you Matt, this solved the issue!
    This is a quick summary for those having the same issue in the future. (I know it helped me when I was using the search feature to have a follow up post from the original poster)
    - accessing local files during preview is a little different from accessing after you export to a swf file.
    - This is due to security settings on flash
    - when trying to access a local file you must add the swf file (flash) that xcelsius created to the secure list on you flash settings
    - Please read the short guide provided by Matt (above) for more details
    Again, thank you Matt!

  • Problems Accessing Local Files

    Hi,
    I'm sure this has been discussed before, but I'm havign problems accessing a file on the target machine's local filesystem. I've signed all my jars and added the all-permissions tag to the jnlp file. However, my code:
    ClassLoader cl = getClass().getClassLoader();
    InputStream is = cl.getResourceAsStream("c:/resources/testsuite.xml");
    fails to find the file "testsuite.xml".
    Is this a classpath issue? I've tried to add c:/resources to the class path but with no luck.
    any help would be much appreciated
    Thanks

    Try "file://c:/resources/testsuite.xml" instead. I
    believe you are suppose to be passing in a valid URL
    and what you passed in wasn't.That's wrong. Resource name should be just a path. It could be a full path started from "/" or just a relative path from given class (here better to use this.class.getResourceAsStream() method).
    Better yet, since you are giving full security access
    to the user's local machine you don't really need to
    rely on the class loader at all. It's just a normal
    file, so you could create your File object and read it
    in the way you do normally. I would suggest to do not rely on File object at all because it can only be dealing with local file system and thats can't be changed in future.

Maybe you are looking for

  • [solved]black screen with xorg 1.6 after resume (intel)

    after upgrading to xorg-server 1.6 no matter if i use s2ram or s2disk, first resume works fine, the second suspend and resume results in a black screen without any chance to swich to any tty. i have read about bug like this which was resolved with us

  • "This backup is too large for the backup volume" - Info

    Hi there. I had a problem with my time machine and got an error stating "This backup is too large for the backup volume". I did noticed after logging in that TM was indexing in the upper right corner [magnifier with a flashing dot(spotlight)] for a f

  • Requisition Approval Process in EHP4

    HI, In EHP4- E-recruiting, I have given one user the role of Restricted Recruiter. During the requisition creation process, this user should not be allowed to release the Requisition. But this user can release the requisition. It is not asking for th

  • ADL in Adobe AIR 3.1 crashes then works then crashes then works

    Hi, I'm using Adobe AIR 3.1 to create an HTML/Javascript application. Whenever I go to run the application using "adl", I'll get the message "Adobe AIR Debug Launcher has stopped working".  If I repeat this several times, the application will eventua

  • My password manager is not working

    After installing and un-installing comcast's constant guard, my passwords are no longer managed through Password manager. I would like to have that function back.