CTS+ configuration in XI. Need help.

Hi All,
I have followed the How to Doc " Enhanced CTS configuration in XI" from the link below
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/20965d21-6c93-2a10-d4a0-9f3c27a939fc
But, functionality is not working. I need advice from any body who followed this document to configure CTS+.
With regards to Pre-req, I have applied all of them correctly in terms of Tp ver, support packs and Java support packs.. I am 100% sure about it. Our Netweaver system is Netweaver04S/Netweaver 7.0 SPS 14.
To begin with have some confusion from the document from Page 15 point 8 and page 18 point 15 regarding the CTS export directory. Our SAp install directory is S: drive and rest of the path. I have created folder called "ctsExport" in S:usrsap<SID>SYSglobalxi, but for the same system (dev) I am not sure how they can point to two different drives? Is that error in document?
and Further in points 25 and 28, for name "com.sap.aii.ibdir.core.transport.exportCtsDirectory" corresponding value is "true" and not the directory path as shown in screens. I am not sure, where I am getting wrong and how to correct the problem.
Please advice..
If I could correct problems in these areas, I will move forward to correct any other problems...
Regards,
K

Hello,
Please try to use the guide for your SP version, it's' may help you better https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/00246ec1-dec5-2a10-58b9-e111c091c00b
BR,
Franklin

Similar Messages

Cash book -FBCJ authorization for configuration of layout - need help

Hi All,
We are facing problem that our end users who all maintaining the cash book are all keep changing the alv layout by clicking the configuration button, I need to control this activities....
Regards
Krishnamoorthy T
Edited by: Krishnamoorthy T on Dec 28, :02 PM

Hi Krishnamoorthy,
Please arrest the authorization for all the end user and please go to the field status and make the filed suppressed.
Warm Regards,
Sivakumar Sathiaymoorthy

I need helping!!! configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.

I need helping configuring RDP access to my local server from a remote location on my Cisco ASA 5505 Firewall.
I have attempted to configure rdp access but it does not seem to be working for me Could I please ask someone to help me modify my current configuration to allow this? Please do step by step as I could use all the help I could get.
I need to allow the following IP addresses to have RDP access to my server:
66.237.238.193-66.237.238.222
69.195.249.177-69.195.249.190
69.65.80.240-69.65.80.249
My external WAN server info is - 99.89.69.333
The internal IP address of my server is - 192.168.6.2
The other server shows up as 99.89.69.334 but is working fine.
I already added one server for Static route and RDP but when I try to put in same commands it doesnt allow me to for this new one. Please take a look at my configuration file and give me the commands i need in order to put this through. Also please tell me if there are any bad/conflicting entries.
THE FOLLOWING IS MY CONFIGURATION FILE
Also I have modified IP information so that its not the ACTUAL ip info for my server/network etc... lol for security reasons of course
Also the bolded lines are the modifications I made but that arent working.
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password DowJbZ7jrm5Nkm5B encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.6.254 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 99.89.69.233 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
object-group network EMRMC
network-object 10.1.2.0 255.255.255.0
network-object 192.168.10.0 255.255.255.0
network-object 192.168.11.0 255.255.255.0
network-object 172.16.0.0 255.255.0.0
network-object 192.168.9.0 255.255.255.0
object-group service RDP tcp
description RDP
port-object eq 3389
object-group service GMED tcp
description GMED
port-object eq 3390
object-group service MarsAccess tcp
description MarsAccess
port-object range pcanywhere-data 5632
object-group service MarsFTP tcp
description MarsFTP
port-object range ftp-data ftp
object-group service MarsSupportAppls tcp
description MarsSupportAppls
port-object eq 1972
object-group service MarsUpdatePort tcp
description MarsUpdatePort
port-object eq 7835
object-group service NM1503 tcp
description NM1503
port-object eq 1503
object-group service NM1720 tcp
description NM1720
port-object eq h323
object-group service NM1731 tcp
description NM1731
port-object eq 1731
object-group service NM389 tcp
description NM389
port-object eq ldap
object-group service NM522 tcp
description NM522
port-object eq 522
object-group service SSL tcp
description SSL
port-object eq https
object-group service rdp tcp
port-object eq 3389
access-list outside_1_cryptomap extended permit ip 192.168.6.0 255.255.255.0 object-group EMRMC
access-list inside_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 192.168.0.0 255.255.0.0
access-list inside_nat0_outbound extended permit ip 192.168.6.0 255.255.255.0 object-group EMRMC
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 eq pcanywhere-data
access-list outside_access_in extended permit udp 69.16.158.128 255.255.255.128 host 99.89.69.334 eq pcanywhere-status
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 object-group RDP
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq ftp
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq ldap
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq h323
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq telnet
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 eq www
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 host 99.89.69.334 object-group SSL
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 object-group NM522
access-list outside_access_in extended permit tcp 69.16.158.128 255.255.255.128 192.168.6.0 255.255.255.0 object-group NM1731
access-list outside_access_in extended permit tcp 173.197.144.48 255.255.255.248 host 99.89.69.334 object-group RDP
access-list outside_access_in extended permit tcp any interface outside eq 3389
access-list outside_access_in extended permit tcp host 66.237.238.194 host 99.89.69.333
access-list outside_access_in extended permit tcp host 66.237.238.194 host 99.89.69.333 object-group rdp
access-list outside_access_in extended permit tcp any host 99.89.69.333 object-group rdp
access-list out_in extended permit tcp any host 192.168.6.2 eq 3389
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp 99.89.69.334 3389 192.168.6.1 3389 netmask 255.255.255.255
static (inside,outside) tcp interface 3389 192.168.6.2 3389 netmask 255.255.255.255
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 99.89.69.338 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.6.0 255.255.255.0 inside
http 0.0.0.0 0.0.0.0 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set peer 68.156.148.5
crypto map outside_map 1 set transform-set ESP-3DES-MD5
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 1
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
tunnel-group 68.156.148.5 type ipsec-l2l
tunnel-group 68.156.148.5 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:f47dfb2cf91833f0366ff572eafefb1d
: end
ciscoasa(config-network)#

Unclear what did not work. In your original post you include said some commands were added but don't work:
static (inside,outside) tcp interface 3389 192.168.6.2 3389 netmask 255.255.255.255
and later you state you add another command that gets an error:
static (inside,outside) tcp 99.89.69.333 3389 192.168.6.2 3389 netmask 255.255.255.255
You also stated that 99.89.69.333 (actually 99.89.69.233, guessing from the rest of your config and other posts) is your WAN IP address.
The first static statement matches Cisco's documentation, which states that a static statement must use the 'interface' directive when you are trying to do static PAT utilizing the IP address of the interface. Since 99.89.69.333 is the assigned IP address of your WAN interface, that may explain why the second statement fails.
Any reason why you are using static PAT (including the port number 3389) instead of just skipping that directive? Static PAT usually makes sense when you need to change the TCP port number. In your example, you are not changing the TCP port 3389.

Need help configuring Excel Services

I've configured both the Excel Serives and Secure Store Target applications and continually receive the following error message when trying to view the Simple Projects List sample report:
An error occurred while accessing application id ProjectServerApplication from Secure Store Service. The following connections failed to refresh:
Project Server - Simple Projects List
The Server Logs show the following errors:
Access Denied: Claims stored in the credentials did not match with the group claim for a group app.
The Microsoft Secure Store Services application Secure Store Service failed to retrieve credentials. The error returned was 'Access Denied.' ...
Access is denied. (Fault Detail is equal to Microsoft.Office.SecureStoreService.Server.SecureStoreServiceFault)
SSS has failed with the following exception: Access is denied.
Unable to esablish a connection using credentials retrieved from SSS. This could be because the Unattended Service Account is not configured or because the credentials retrieved from SSS are not valid.
I've repeated the steps to create these configurations a few times, and continue to get the same errors. Any help would be appreciated!
Thanks

Hello,
I need help setting up excel services.
Excel service is already running on sharepoint server.
I have one reporting file which is generated by DBA with database connection. i want to upload that file under document library and i want whenever user open it through document library, it gets updated through database connection
This is my first time, so pls guide me
Reporting file has authentication set to --> None
Do i require any specific settings for authentication? like unattended account ? which username should i use
Connection String -->
Provider=SQLOLEDB.1;Integrated Security=SSPI;Persist Security Info=True;User ID=ExcelServices;Initial Catalog=SurveyData;Data Source=jdb1;Use Procedure for Prepare=1;Auto Translate=True;Packet Size=4096;Workstation ID=RSTKW7W-06709;Use Encryption for Data=False;Tag
with column collation when possible=False
http://../training/sptestsite/Medication_Audit_Report
http://../training/sptestsite/Medication_Audit_Data_Connection_Library/
Trusted File Location - is this place do i need to upload that reporting file?
Trusted Data Connection Libraries - is this place do i need to save connection file .odc ?
If i am not wrong, should i put
Trusted File Location = http://../training/sptestsite/Medication_Audit_Report
Trusted Data Connection Libraries = http://../training/sptestsite/Medication_Audit_Data_Connection_Library/
http://../training/sptestsite/Medication_Audit_Report -- Here only reporting file will be uploaded right?
http://../training/sptestsite/Medication_Audit_Data_Connection_Library/ -- Here only database connection .odc file will be uploaded?
what other settings are required. please correct me
my email address - [email protected]
Harsh

Need help setting up and configuring rsync

Hello
I need help setting up, or rather configuring rsync to sync data between my brand new iMac and my Macbook Air.
Here is what I would like to:
- I want all of the files on both machines to be an exact mirror or copy of each other. Basically I have an iMac for at home, and then a Macbook Air for the road.
- The main folder on both Macs is called 'Sara' and I want the contents (mainly the 'movies' folder, 'music' folder, 'documents' folder and 'pictures' folder) to immediately sync up with each other when both of them are on my home network.
- this means if I'm working on a file at home on my Macbook, it will immediately write to the same directory on my iMac and vice versa (if I'm working on file(s) on my iMac, it will immediately save the contents to my Macbook). This way, if I'm working on last minute project my iMac, and then have to head out the door to the airport, the file is immediately saved to my Macbook (no usb for USB transfer).
- hopefully this makes sense??
Any help is greatly appreciated!
Thanks

It's a lofty but unrealistic goal. Rsync does not run automatically. There is no realistic method of instantaneously synching two computers over the internet or even on a LAN.
I would suggest you might try using Synk Pro which, in theory, can keep two devices in sync when they are both on the same network (and both have shared and mounted drives.)
If you must do this with rsync then I suggest a Google search for rsync tutorials.

I need help configuring three products: WRVS4400N, WAG325N and WVC200

Hello,
I want your help in three linksys products as mentioned below:
WAG325N ADSL2+ Router
WVC200 PTZ CAMERA
WRVS4400N VPN Router
The computer connections and configuration of above linksys products which I am working with and which are connected with the above three linksys products at present are as follows:
1) I have one server and one laptop.
2) Laptop has two wireless adapters which I use to connect to the routers.
3) The server is connected to the WRVS4400N Router through one of the four ethernet ports mentioned on backside of the WRVS4400N Router. The DHCP of this router is disabled by me and the router's default IP 192.168.1.1 was changed to 192.168.1.12
4) The WRVS4400N router is connected to the Wag325N router for internet access to the server and server is connected to WRVS4400N Router as mentioned in point number 3 above.
5) The WAG325N router is setup as per the instructions mentioned that came with the CD of this router. The only change that I have modified is the router's default IP. I have changed the default IP of WAG325N from 192.168.1.1 to 192.168.1.13 and DHCP is enabled on this router.
The help that I want is step by step as follows:
1) I want to configure the both routers in such a way so that I can access them from anywhere across the world i.e. remotely using internet.
2) I have WVC200 Camera which I setup according to instructions mentioned in the CD and also configured the DDNS service. But when the " RJ45 Cable is connected " to my WAG325N router and Camera, then only the camera works properly. What I want is that after the setup is completed, I want to remove the RJ45 Cable connected from my camera to router and use the camera wirelessly from any location within the range of my above mentioned WAG325N router. I need flexibility to use my camera without cable connections from any location and any rooms of my house. I also configured the port forwarding and DDNS properly. The only problem is that if I remove the Cable after the setup of camera is finished, then the camera access is not working on LAN or internet(through DDNS). Whereas the same works on LAN and internet using the DDNS service, when the cable is physically connected to the WAG325N router. Also I want one more thing additionally other then this. I want to use this camera wirelessly by configuring the port forwarding options on both routers at a same time(i.e. simultaneously at once on WRVS4400N and WAG325N).
3) Now as two DHCP cannot work at a same time and as my routers are connected with each other, So I have disabled the DHCP on WRVS4400N. Here I need help so that DHCP can be enabled on both at a same time. Because if the DHCP is not enabled on WRVS4400N then I have to give IP to the server which is connected with server. If I enable the DHCP then there are two DHCP's at a same time on same network and thus problems occurs in internet access to the server. So, what should I do in such a way so that I do not have to give any IP to my server and set it to automatic.
4) This question is just for my knowledge so that I can use the above mentioned linksys purchases upto full extent possible in future. I want to know what is VPN and how is it usefull? What is the difference between VPN and VPN tunnel? How can VPN be used to access all my network resources connected with my server in the above situation where my server is connected to WRVS4400N which in turn is connected to WAG325N?
Thanks !
Sincerely
Kalpesh Sharma
+91-79-25351208
+919227435453
Ahmedabad, India.

for question number 1:
you said that your main router is WAG325N, for you to remotely access the 2nd router is for you to forward the IP addr [192.168.1.12] on your first router and change its management port of your second router that is located on either the security tab or the administration tab on its User Interface
to access your first router open and Internet Explorer and enter
http://[public IP addr]:[management port]
the PUBLIC IP or INTERNET IP is located on the status page of your router
to access your second router just change the management port to
ex.
http://66.77.88.99:8080 first router
http://66.77.88.99:8081 second router
for question number 2:
make sure that you have configured all wireless settings on both your camera and your main router WAG235N, once done save settings and power down your camera and power it back up.
for question number 3:
for you to enable DHCP on both routers your connection can go like so...
from a regular port of your main router going to the INTERNET port of your second router [this way you can enable DHCP on both routers]. INTERNET is no problem, your cesond router will be able to get connection
for question number 4:
VPN - Virtual Private Network
VPN tunnel -is/are connections from router to router [gateway to gateway]
VPN is used to connect a diff network on a diff location for you to have access to the shared filed [it is like a file sharing through the internet]
for you to be able to use VPN tunnel you have to connect to a different VPN router on a diff location. In that way you can get access to the other network

I have a PC and a need help to configure my external hard disk on my network. Thanks

I have a PC and a need help to configure my external hard disk on my network. Thanks

If you mean you wish to plug a USB drive into the Airport Extreme router (or TC not express) that is easy..
The disk must be formatted FAT32.. as if.. stay away from FAT .. or HFS+ ie Mac OS extended Journaled.
Format the disk on a Mac is best.. and even use GUID partition scheme not MBR.
The PC has no issue writing and reading files because this is a network drive.. The PC does not write to the drive.. it writes files to the Airport OS which writes and reads the disk and passes the info using standard windows SMB.. To the windows computer it will be a Windows NT server.. FAT32 setup.
If your setup is different.. to my hugely guessed assumptions.. give details.. always helps to have.. make and model.
Make and model of disk.. make and model of router.. how the setup will be done.. what windows OS you run.. etc etc.
As it stands your question could have nothing to do with apple at all.. other than you posted in a forum so I guess there is something apple in there somewhere.

WRT54GS cannot be configured, need help!!!!

Ok.. I am getting so lost. I will try to explain the best I can what is going on. I just bought the Wireless G router with speedbooster and put the CD in to set it up, did everything it told me to do on the screen as far as pluggin cables in yada yada. When it came to step 4 of 4 it said "Waiting for Router". Then after about 2-3 minutes it comes back saying the following:
YOUR ROUTER DOES NOT APPEAR TO BE CONNECTED PROPERLY
Error 322: New router or Gateway not detected
Follow these steps:
1) Make sure you are connecting your new router and not your old router
2) Make sure the ethernet cable from your computer is securely connected to a LAN port on the back of your new router
3) Click retry to try installing your router again
Also, when I try to retry the setup without unplugging anything it says this:
Linksys EasyLink Advisor Setup Wizard has discovered that you are already connected to a router. Many people choose to replace an existing router with their new Linksys Router.
I can connect to the internet without configuring the router!!! It isn't secure though! I want to configure my router so that it is secure and I don't know what to do to fix this.
I am using a Comcast provided modem, RCA model # DCM425
Any help would be greatly appreciated... Remember I am a noob so please don't confuse me more with words I don't understand.. Thanks
One more thing. When it is "Waiting for router" the 2 computer icon comes up at bottom of screen saying acquiring IP address so I double clicked on it and it would be connected with the IP address 192.168.1.1 and then all of a sudden it would say Invalid IP address not connected. I really need help here!!!

Ok, I'm not 100% sure I can help you, but I will try.
First thing, find the setup disk that came with the router and use it as a coaster or a frisbee or something because it is almost completely worthless.
Until you have completed the setup of the router, I would suggest using a computer that is connected directly to the router via ethernet cable. The reason being, if you change any settings wirelessly, such as security features, you will be disconnected and unable to access it again. So use a computer that is directly connected for setup.
The IP address you saw in you system tray is the IP address of the router itself. You actually need this for your router setup. Open whichever web browser you use and type in that IP address, nothing else. 192.168.1.1 A login screen should appear for you to enter your user name and password. Leave the user name blank and for the password enter "admin" without the quotes. This should bring you to your basic settings screen for the router.
From this point, I'm sure exactly how you want to set everything up. If you're not very familiar with networking or routers I would suggest you change very little. If you desire security for your network (which I suggest) click on the "Wireless" tab at the top of the screen. This should bring you to basic wireless settings. From here, you can change the name of your wireless network, change the broadcast frequency and enable/disable wireless broadcast. You can change these if you like or leave them alone whichever you prefer. I do suggest changing the name of you network (SSID) so you can tell which one is yours when you try to connect. It gets confusing when everyone in your neighborhood has a Linksys and all of the names look similar.
Once you're done here, next click on the "Wireless Security" tab within the "Wireless" tap. Make sure you are click "Wireless Security" and not just "Security." From here, you can select the kind of wireless security you want to use. I'm not highly informed on which of these is the best, but WEP is probably the strongest security you're going to need anyway, so I would go with that. After you select WEP you get a few more options. For "default transmit key" just select one. Then in the "WEP Encryption" drop down, select "128 bits 26 hex digits." 64 would most likely be ok, but 128 bit encryption is definitely better.
In the next box "Passphase" enter a word or short phrase that is only known to you an click generate. The four boxes below will now have you WEP keys. I delete all but the first key to keep things simple, but whatever you want to do is up to you. After you delete the other three lines, select the key in your first line and select/copy it so that you can just paste it into the box in network options when you're connecting to the network. Regardless, I would also write this key down somewhere. If you have multiple computers in the house you have to enter it on each and every one and it's a pain to go back and forth. Click save settings. You're pretty much done. There are other things you can do to beef up security, but this is the most basic and it's still quite strong.
If you are looking at playing games frequently or anything like that I would go to PortForward.com
Any other questions you have, you should be able to google I think. I hope I can help. Good Luck.

Need Help W/ Raid Configuration

I NEED HELP W/ MY RAID CONFIGURATION.
I HAVE THE K7N2 DELTA-ILSR MOBO W/ A XP2600+, I HAVE TWO 40 GIG HARDDRIVES THAT I WANT TO RAID 0 TOGHTER.
I HAVEN'T FOUND IN THE MANUALL HOW TO SET UP THE RAID ARREY, I DONT NO HOW TO SET THE DRIVER AS FAR AS SLAVE/MASTER SETTINGS, WITCH ONE NEEDS TO GO TO WITCH CHANNEL ( PRIMARY/SECONDARY/CS).
- EVERY TIME THAT I SET IT UP THE ARREY IS SHOWING ONLY 1 DRIVE, I BELIVE THAT RAID 0 SHOULD HAVE BOTH OF THE DRIVES AS 1 BIG DRIVE, CAN SOME ONE HELP ME W/ INSTARUCTIONS HOW TO CREATE THIS ARREY?
thanks guys

I had RAID 0 set on my system. I used the MSI Live Update software to update my RAID controller because it said it needed it. It hung up in the middle of the update, so I let it sit for 24 hours. Finally I rebooted, & now it won't even see the drives. If you go with RAID 0, back up your data, and keep it backed up!!! I will say this, while it worked, it was really really fast!!! In order to make my RAID work (while it lasted) I used two SATA drives. I believe you can also use one ATA & 1 SATA instead of two SATA drives. If you use 1 ATA drive, set it to master & connect to IDE 3. This will be the only drive on that cable. During the boot up, you have to follow the prompt & press to enter the FastBuild (tm) Utility. Once there, you can choose Auto Setup & it will do the work for you. I must re-iterate, KEEP YOUR DATA BACKED UP!!!!!! I hope this helps. Good luck!
K7N2G-ISLR, AMD 2600+, Twin rapter 37gb hard drives, 1gb DDR-400, G-Force FX
5600 256mb AGP etc.

Need help on struts configuration with ColdFusion 10 using IIS

We need help on struts configuration with ColdFusion 10 using IIS.
Earlier we were using ColdFusion 8 with IIS 6 for one of our application. This application internally calls struts. After upgrading to ColdFusion 10 struts calls are not loading. We get 404 error.
In ColdFusion 8 struts were configured using actions extension .do in IIS from this file-
C:\ColdFusion8\runtime\lib\wsconfig\jrun_iis6.dll.
But in ColdFusion 10 this file is not present as ColdFusion 10 uses Tomcat in place of Jrun.
Also there is no information in ColdFusion log file.

Duane wrote:
doctormirabilis, Welcome to the discussion area!
1) how can i configure the time capsule in order to operate as a remote base station synchronizing with the relay using the ethernet port?
Configure the Time Capsule to act as a bridge (not distributing IP addresses). Also configure the Time Capsule to create an 802.11n wireless network with a unique network name (SSID). That's it.
2) how can i avoid that my powerbook while accessing my wireless network does connect through the relay station instead of using the time capsule?
Configure the Time Capsule to use a different network name than the WDS link between the 2 AirPort Express (AX). Configure the PowerBook to use the Time Capsule network.
There are 2 pieces of information that you should be aware of...
(1) None of the PowerBooks are capable of 802.11n.
(2) The WDS link cuts your available bandwidth in half. So the wireless link to your neighbor's has a maximum potential of 27 Mbps.
Let's for a minute assume that you have a Mac compatible with 802.11n. In your configuration the time you could take advantage of the 802.11n speed is when the Mac is sending/recieving data directly from/to the Time Capsule.
There would be NO speed increase in Internet access. The speed of Internet access is going to be controlled by the slowest link in the path to the Internet. That is probably the connection to the ISP. The next slowest path is the WDS link to your neighbor's.
Duane,
I am in a similar situation, sharing internet with my neighbor. Do you think it would be plausible to hook up a vonage phone adapter to time capsule's ethernet port if time capsule is bridging from my neighbor's router in the configuration you have described? A check of my upload speed shows 1.67Mbps (powerbookG4 w/ airport extreme). Vonage reccommends 90kbps minimum upload speed. Am I going to lose some speed putting the Vonag adapter behind time capsule?
Thank you

NEED HELP WITH WORKFLOW CONFIGURATION

I need help with 3 situations below. Please help me with these. How do I configure these. I also haveto provide specs to the Abaper. What exactly do I need to include in the specs. I anyone has the specs similar to these please send me over. Also tell me what I need to do to get these requirements fulfilled.
1) Description:
This is a workflow requirement to serve as a reminder of upcoming investment
maturities.
Requirements Details:
Create a workflow to serve as a reminder of upcoming investment maturities.
Donor System Processing Narrative:
Read the maturity dates on investments.
Target System Processing Narrative:
Send a notice to the parties that an investment will be maturing soon.
2) Description:
Implement workflow to route invoice receipts using a one time vendor for management
review and posting
Desired Functionality:
If a one time vendor is entered by the AP Voucher Clerk the invoice will be automatically
parked by the program and a workflow notification triggered to the Accounting
Supervisor and Accounting Manager (backup). The Accounting Supervisor will review
the parked document and imaged copy of the actual invoice and post the parked
document.
3) Description:
An approval workflow is needed for credit memos posted to SAP customer accounts.
Desired Functionality:
The Cash Journal Clerk will post a credit memo to the customer account using transaction
FV75 Park Customer Invoice. This transaction will automatically trigger a workflow to
the Accounting Manager for approval and then to the CFO who will approve and post the
parked document. (In order for this transaction to automatically trigger what configuration needs to be done).

Bob;
You can borrow the example code that ships with both NI-DAQ (in case you are doing NI-DAQ function calls) and Labview. The best examples to start with are the ones that have the prefix STC.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

Need Help on Configuring the Site to Site VPN from Cisco 2811 to Websense Cloud for web Traffic redirect

Hi All,
I need help on Configuring the Site to Site VPN from Cisco 2811 to Websense Cloud for web Traffic redirect
2811 having C2800NM-ADVIPSERVICESK9-M
2811 router connects to the Internet SW then connects to the Internet router.
Note- For Authentication am using the Device ID & Pre share key. I am worried as all user traffic goes with PAT and not firing up my tunnel for port 80 traffic. Can you please suggest what can be the issue ?
Below is router config for VPN & NAT
crypto keyring ISR_Keyring
pre-shared-key hostname vpn.websense.net key 2c22524d554556442d222d565f545246
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp keepalive 10
crypto isakmp profile isa-profile
   keyring ISR_Keyring
   self-identity user-fqdn [email protected]
   match identity user vpn-proxy.websense.net
crypto ipsec transform-set ESP-NULL-SHA esp-null esp-sha-hmac
crypto map GUEST_WEB_FILTER 10 ipsec-isakmp
set peer vpn.websense.net dynamic
set transform-set ESP-NULL-SHA
set isakmp-profile isa-profile
match address 101
interface FastEthernet0/1
description connected to Internet
ip address 216.222.208.101 255.255.255.128
ip access-group HVAC_Public in
ip nat outside
ip virtual-reassembly
duplex full
speed 100
no cdp enable
crypto map GUEST_WEB_FILTER
access-list 101 permit tcp 192.168.8.0 0.0.3.255 any eq www
access-list 103 deny   ip 192.168.8.0 0.0.3.255 host 85.115.41.187 log
access-list 103 deny   ip 192.168.8.0 0.0.3.255 host 85.115.41.181 log
access-list 103 deny   ip 192.168.8.0 0.0.3.255 host 85.115.41.182 log
access-list 103 deny   ip 192.168.8.0 0.0.3.255 86.111.216.0 0.0.1.255
access-list 103 deny   ip 192.168.8.0 0.0.3.255 116.50.56.0 0.0.7.255
access-list 103 deny   ip 192.168.8.0 0.0.3.255 86.111.220.0 0.0.3.255
access-list 103 deny   ip 192.168.8.0 0.0.3.255 103.1.196.0 0.0.3.255
access-list 103 deny   ip 192.168.8.0 0.0.3.255 177.39.96.0 0.0.3.255
access-list 103 deny   ip 192.168.8.0 0.0.3.255 196.216.238.0 0.0.1.255
access-list 103 permit ip 192.168.8.0 0.0.3.255 any
ip nat pool mypool 216.222.208.101 216.222.208.101 netmask 255.255.255.128
ip nat inside source list 103 interface FastEthernet0/1 overload
ip nat inside source route-map nonat pool mypool overload

How does Websense expect your source IPs in the tunnel? 192.168.8.0 0.0.3.255 or PAT'ed 216.222.208.101 ?
Check
show crypto isakmp sa
show crypto ipsec sa
show crypto session
You'd better remove the preshared key from your post.

I need help with Mavericks Server: an error occurred while configuring your server. I

I need help with Mavricks Server, I get the following: an error occurred while configuring your server. I have deleted the Server.app several times along with the associated com.apple and Server folder. Any more help would be appreciated.

There are usually some log files around, related to the installation. See if Console.app (Applications > Utilities) shows anything relevant to the error, when you've done a fresh install of Server.app and tried the configuration.

Need help with AS8 configuration

Our present situation is like this:
AS7 with single domain and multiple server instances
instance A running on port xxx containing app1
instance B running on port yyy containing app2
instance C running on port zzz containing app3
Now, when I move to AS8.1 PE, I dont see the option to create a server instance inside a domain. I need to create 3 domains in order to accomplish the same task as above. Not only that, now I need to login to 3 different admin servers to manage the 3 apps on 3 ports
I need help with some options I can use
thanks

I'm not sure but i think that on 8.1 pe you can have only one server instance by default...
But you can olso try by command line tool asadminin [installdir soas]/binuse:
asadmin --help for a list of commands available.
In the list should be create-instance to create a stand alone instance.
Hi
Stefano

Software updates stuck at "Configuration Installation"...NEED HELP?

I have a new Mac Book and I performed software updates when I first bought it and everything downloaded and installed seemlessly. Just recently when I tried downloading and installing OS 10.5.5, the comp got stuck when it was shutting down and trying to instill the updates. I just downloaded OS 10.5.6 and it has done the same thing. It said that updates have been downloaded, do you want to restart. I click continue, it begins to shut down and start the install of the updates and it stalls and doesn't do anything. I need help!!

Same problem here and we tried the Apple link suggested but it is still not working....
Purchased a new Aluminum Macbook for my son at Xmas and he has not been able to download anything. We have run permissions repair, cleared Library etc multiple time and still get error messages when attempting installation. Poor kid is very frustrated as am I. Any further help would be much appreciated!
Thanks!

CTS+ configuration in XI. Need help.

Similar Messages

Maybe you are looking for