DACL does not get downloaded to Cisco Switch from ISE

Hello,
I have a cisco switch with ios: c3550-ipbasek9-mz.122-44.SE6.bin
I am trying to push dACL fro my ISE device into the switch, but it is not getting applied to switch. dynamic vlan assignment workds fine, but dACL doesnot apply
Any instruction plz?

Hi Jatin,
ISE is properly configured for dACL,   i think there is some compatibility issue on cisco switch ios.
following is the debug output>>
06:36:43: dot1x-packet:Received an EAP packet on interface FastEthernet0/11
06:36:43: EAPOL pak dump rx
06:36:43: EAPOL Version: 0x1 type: 0x0 length: 0x0006
06:36:43: dot1x-packet:Received an EAP packet on the FastEthernet0/11 from mac 0019.b981.e812
06:36:43: dot1x-sm:Posting EAPOL_EAP on Client=1D68028
06:36:43:     dot1x_auth_bend Fa0/11: during state auth_bend_request, got event 6(eapolEap)
06:36:43: @@@ dot1x_auth_bend Fa0/11: auth_bend_request -> auth_bend_response
06:36:43: dot1x-sm:Fa0/11:0019.b981.e812:auth_bend_response_enter called
06:36:43: dot1x-ev:dot1x_sendRespToServer: Response sent to the server from 0019.b981.e812
06:36:43: dot1x-sm:Fa0/11:0019.b981.e812:auth_bend_request_response_action called
06:36:43: RADIUS/ENCODE(00000049):Orig. component type = DOT1X
06:36:43: RADIUS(00000049): Config NAS IP: 192.168.2.250
06:36:43: RADIUS/ENCODE(00000049): acct_session_id: 73
06:36:43: RADIUS(00000049): sending
06:36:43: RADIUS(00000049): Send Access-Request to 192.168.2.231:1812 id 1645/99, len 267
06:36:43: RADIUS: authenticator 5B 61 1D 64 D3 D5 9F AD - 23 E0 11 11 B3 C3 5C 81
06:36:43: RADIUS: User-Name           [1]   6   "test"
06:36:43: RADIUS: Service-Type        [6]   6   Framed                    [2]
06:36:43: RADIUS: Framed-MTU          [12] 6   1500
06:36:43: RADIUS: Called-Station-Id   [30] 19 "00-11-5C-6E-5E-0B"
06:36:43: RADIUS: Calling-Station-Id [31] 19 "00-19-B9-81-E8-12"
06:36:43: RADIUS: EAP-Message         [79] 8
06:36:43: RADIUS:   02 7A 00 06 0D 00                 [ z]
06:36:43: RADIUS: Message-Authenticato[80] 18
06:36:43: RADIUS:   A6 AB 5A CA ED B8 B4 1E 36 00 9D AB 1A F6 B9 E0                [ Z6]
06:36:43: RADIUS: Vendor, Cisco       [26] 49
06:36:43: RADIUS:   Cisco AVpair       [1]   43 "audit-session-id=C0A802FA0000006F016B36D8"
06:36:43: RADIUS: NAS-Port-Type       [61] 6   Ethernet                  [15]
06:36:43: RADIUS: NAS-Port            [5]   6   50011
06:36:43: RADIUS: NAS-Port-Id         [87] 18 "FastEthernet0/11"
06:36:43: RADIUS: State               [24] 80
06:36:43: RADIUS:   33 37 43 50 4D 53 65 73 73 69 6F 6E 49 44 3D 43 [37CPMSessionID=C]
06:36:43: RADIUS:   30 41 38 30 32 46 41 30 30 30 30 30 30 36 46 30 [0A802FA0000006F0]
06:36:43: RADIUS:   31 36 42 33 36 44 38 3B 33 35 53 65 73 73 69 6F [16B36D8;35Sessio]
06:36:43: RADIUS:   6E 49 44 3D 69 73 65 2D 73 65 72 76 65 72 2D 31 [nID=ise-server-1]
06:36:43: RADIUS:   2F 31 37 31 30 32 35 39 38 38 2F 32 34 3B    [ /171025988/24;]
06:36:43: RADIUS: NAS-IP-Address      [4]   6   192.168.2.250
06:36:43: %LINK-3-UPDOWN: Interface FastEthernet0/11, changed state to up
06:36:43: RADIUS: Received from id 1645/99 192.168.2.231:1812, Access-Challenge, len 1134
06:36:43: RADIUS: authenticator 78 36 A3 38 30 1C F0 7A - 19 83 93 81 B4 6B FF 9E
06:36:43: RADIUS: State               [24] 80
06:36:43: RADIUS:   33 37 43 50 4D 53 65 73 73 69 6F 6E 49 44 3D 43 [37CPMSessionID=C]
06:36:43: RADIUS:   30 41 38 30 32 46 41 30 30 30 30 30 30 36 46 30 [0A802FA0000006F0]
06:36:43: RADIUS:   31 36 42 33 36 44 38 3B 33 35 53 65 73 73 69 6F [16B36D8;35Sessio]
06:36:43: RADIUS:   6E 49 44 3D 69 73 65 2D 73 65 72 76 65 72 2D 31 [nID=ise-server-1]
06:36:43: RADIUS:   2F 31 37 31 30 32 35 39 38 38 2F 32 34 3B    [ /171025988/24;]
06:36:43: RADIUS: EAP-Message         [79] 255
06:36:43: RADIUS:   4D 5D 13 47 FC 46 16 EE 62 76 40 09 77 48 31 B6 01 6B 5E 52 33 56 A2 1E 34 [M]GFbv@wH1k^R3V4]
06:36:43: RADIUS:   02 32 39 FA 4D CA 79 18 4A 42 A2 4E 5C BD AE 29 D2 3D D1 5A FC C2 ED 3E E5 FB C6 B8 D8 DE A8 75 EB 3A A5 7D 02 03 01 00 01 A3 81 CD 30 [29MyJBN\)=Z>u:}0]
06:36:43: RADIUS:   81 CA 30 0B 06 03 55 1D 0F 04 04 03 02 01 86 30 0F 06 03 55 1D 13 01 01 FF 04 05 30 03 01 01 FF 30 1D 06 03 55 1D 0E 04 16 04 14 C4 56 80 A7 C9 18 50 92 EE CC 91 D4 E1 EC DB AD E7 1E 70 A8 30 79 06 03 55 1D 1F 04 72 30 70 [0U0U00UVPp0yUr0p]
06:36:43: RADIUS:   30 6E A0 6C A0 6A 86 32 68 74 74 70 3A 2F 2F 73 79 73 6C [0nlj2http://sysl]
06:36:43: RADIUS:   6F 67 2D 73 65 72 76 65 72 2F 43 65 72 74 45 6E [og-server/CertEn]
06:36:43: RADIUS:   72 6F 6C 6C 2F 46 4D 46 42 5F 54 72 75 73 74 65 [roll/FMFB_Truste]
06:36:43: RADIUS:   64 43 41 2E 63 72 6C 86 34 66 69 6C 65 3A 2F 2F 5C [dCA.crl4file://\]
06:36:43: RADIUS:   5C 73 79 73 6C 6F 67 2D 73 65 72 76 65 72 5C 43 [\syslog-server\C]
06:36:43: RADIUS:   65 72 74 45 6E 72 6F 6C 6C 5C 46 4D 46 42 5F 54 [ertEnroll\FMFB_T]
06:36:43: RADIUS:   72 75 73 74 65 64 43 41 2E         [ rustedCA.]
06:36:43: RADIUS: EAP-Message         [79] 251
06:36:43: RADIUS:   63 72 6C 30 10 06 09 2B 06 01 04 01 82 37 15 01 04 03 02 01 00 30 0D 06 09 2A 86 48 86 F7 0D 01 01 05 05 00 03 82 01 01 00 63 BA F8 CE D5 8B 0E 94 77 AE 86 6C 37 AB 2F 36 9A B2 85 D5 4A [crl0+70*Hcwl7/6J]
06:36:43: RADIUS:   74 8C 33 F5 93 06 A6 57 8D 39 56 8F 02 08 97 CB C6 08 70 8C 22 1E 5D 1F A8 26 6D 60 1F 05 62 D1 24 AB 03 8C 41 F8 1C F1 F8 C2 87 8B 97 02 71 FC 6A [t3W9Vp"]&m`b$Aqj]
06:36:43: RADIUS:   EB 12 FC DD 8C 5C 9C 2D AF D2 C4 1C 18 1B 40 BE 78 B0 54 55 59 89 03 1B B7 FB 91 85 EE CA C0 18 1C 78 5D 4D BA FA 9E 44 D3 45 53 A3 BE 46 8A FB 81 BD F1 4C B3 3B [\-@xTUYx]MDESFL;]
06:36:43: RADIUS:   D6 66 7E 5B 79 9F 83 53 5E 49 92 B5 7F E5 1A E2 86 8C 83 96 7D 75 A5 1D 08 4E 32 C3 5E EC BF 28 53 EC 53 8A C3 E0 36 [f~[yS^I}uN2^(SS6]
06:36:43: RADIUS:   82 EE AA 0D 38 3E BA 9C 1D D9 24 BD 48 A6 EE 44 BD 95 68 85 CA 8C 44 F8 E8 A2 FB 94 BC 6F 7C F2 06 91 6C A0 A6 BB 7B 7F 56 BD 15 32 A4     [ 8>$HDhDo|l{V2]
06:36:43: RADIUS: Message-Authenticato[80] 18
06:36:43: RADIUS:   DD 82 F7 10 3F C7 B5 62 9B 2A BB 24 16 A7 59 33            [ ?b*$Y3]
06:36:44: RADIUS(00000049): Received from id 1645/99
06:36:44: RADIUS/DECODE: EAP-Message fragments, 253+253+253+249, total 1008 bytes
06:36:44: dot1x-packet:Received an EAP request packet from EAP for mac 0019.b981.e812
06:36:44: dot1x-sm:Posting EAP_REQ on Client=1D68028
06:36:44:     dot1x_auth_bend Fa0/11: during state auth_bend_response, got event 7(eapReq)
06:36:44: @@@ dot1x_auth_bend Fa0/11: auth_bend_response -> auth_bend_request
06:36:44: dot1x-sm:Fa0/11:0019.b981.e812:auth_bend_response_exit called
06:36:44: dot1x-sm:Fa0/11:0019.b981.e812:auth_bend_request_enter called
06:36:44: dot1x-packet:dot1x_mgr_send_eapol :EAP code: 0x1 id: 0x7B length: 0x03F0 type: 0xD data: @Cfui[ab2,Jt1){                                                                                                                              2]g&GZ1pIbu;+Ga;iF"jy#
oohuV.aFZ4_|
P0`At   )B
06:36:44: dot1x-ev:FastEthernet0/11:Sending EAPOL packet to group PAE address
06:36:44: dot1x-ev:dot1x_mgr_pre_process_eapol_pak: Role determination not required on FastEthernet0/11.
06:36:44: RADIUS: Message-Authenticato[80] 18
06:36:44: RADIUS:   F5 B0 56 D3 C6 87 BD 10 6E C7 4A 72 5B 5C 60 C5           [ VnJr[\`]
06:36:44: RADIUS: Vendor, Cisco       [26] 49
06:36:44: RADIUS:   Cisco AVpair       [1]   43 "audit-session-id=C0A802FA0000006F016B36D8"
06:36:44: RADIUS: NAS-Port-Type       [61] 6   Ethernet                  [15]
06:36:44: RADIUS: NAS-Port            [5]   6   50011
06:36:44: RADIUS: NAS-Port-Id         [87] 18 "FastEthernet0/11"
06:36:44: RADIUS: State               [24] 80
06:36:44: RADIUS:   33 37 43 50 4D 53 65 73 73 69 6F 6E 49 44 3D 43 [37CPMSessionID=C]
06:36:44: RADIUS:   30 41 38 30 32 46 41 30 30 30 30 30 30 36 46 30 [0A802FA0000006F0]
06:36:45: dot1x-ev:FastEthernet0/11:Sending EAPOL packet to group PAE address
06:36:45: dot1x-ev:dot1x_mgr_pre_process_eapol_pak: Role determination not required on FastEthernet0/11.
06:36:45: dot1x-registry:registry:dot1x_ether_macaddr called
06:36:45: dot1x-ev:dot1x_mgr_send_eapol: Sending out EAPOL packet on FastEthernet0/11
06:36:45: EAPOL pak dump Tx
06:36:45: EAPOL Version: 0x2 type: 0x0 length: 0x0039
06:36:45: EAP code: 0x1 id: 0x7E length: 0x0039 type: 0xD
06:36:45: dot1x-packet:dot1x_txReq: EAPOL packet sent to client (0019.b981.e812)
06:36:45: dot1x-sm:Fa0/11:0019.b981.e812:auth_bend_response_request_action called
06:36:46: dot1x-ev:dot1x_mgr_pre_process_eapol_pak: Role determination not required on FastEthernet0/11.
06:36:46: dot1x-packet:dot1x_mgr_process_eapol_pak: queuing an EAPOL pkt on Authenticator Q
06:36:46: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
06:36:46: EAPOL pak dump rx
06:36:46: EAPOL Version: 0x1 type: 0x0 length: 0x0006
06:36:46: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/11 CODE= 2,TYPE= 13,LEN= 6
06:36:46: dot1x-packet:Received an EAPOL frame on interface FastEthernet0/11
06:36:46: dot1x-ev:Received pkt saddr =0019.b981.e812 , daddr = 0180.c200.0003,
                    pae-ether-type = 888e.0100.0006
06:36:46: dot1x-ev:dot1x_auth_process_eapol: EAPOL flag status of the port Fa0/11 is TRUE

Similar Messages

An installed Theme does not get disabled or even removed from the main body of the browser, only from the header.

After even uninstalling the all Themes and reverting to Default, the footer continues to display that one particular theme - Celestial. Concomitantly, against that dark background whenever the mouse cursor moves over a line in Gmail, the line turns White. Unreadable and irritating.
This happened before I updated to Firefox 12 and persists when I have updated to Firefox 13 today.
Firefox on my other desktop with the same Theme does not have this problem.
Grateful for any guidance in getting a solution.

Do you mean that you still see a persona at the bottom part of the browser window?
See:
*http://kb.mozillazine.org/Preferences_not_saved
*https://support.mozilla.org/kb/Preferences+are+not+saved
You can also remove the personas files (lightweighttheme-header and lightweighttheme-footer) in the Firefox Profile Folder.
* http://kb.mozillazine.org/Themes (Lightweight theme)
You can use this button to go to the Firefox profile folder:
*Help > Troubleshooting Information > Profile Directory: Open Containing Folder

Sent items of my exchange account in iphone does not get updated

Hi..
sent items of my exchange account in iphone does not get updated. Mails sent from iphone are getting recieved by everyone and same is getting updated in outlook. sent items for the same account in ipad is getting updated. I am not facing this problem with any other folders in my exchange account. someone please provide a solution for this. I have tried resetting, restoring but nothing works...
Regards,
Yash

Hi,
The problem could be the currency of the valuation area. It has to be the local currency. Maybe the company code has the local currency but the valuation currency is another.
Without having access to your system it is difficult to say. Maybe double check your customizing for assignment of update types for derived business transactions in spro:
Transaction Manager
-> General Settings
     -> Accounting
         -> Settings for Position Management
              -> Derived Business Transactions
                  -> Update Types
                      -> Assign Update Types for Derived Business Transactions
I hope this is helpful.
M Trein
Edited by: Marcelo Trein on Jun 21, 2011 12:19 AM (spelling)

Ordered Quantity does not get copied to Invoice by DIAPI

Hi All,
I am stuck with an issue in Invoice creation using DI API by code.The field Ordered Qty (DB Filed INV1.OrderedQty) does not gets copied to Invoice line from delivery lines. But while we add invoice from delivery >Copy To> AR Invoice , it gets copied to Invoice lines. This OrderedQty field is not exposed through DI API, so we cant set that field throgh code. What I do in Invoice creation code is as follows.
SAPbobsCOM.Documents oINV;
                    oINV = (SAPbobsCOM.Documents)
                        modups.oCompany.GetBusinessObject(SAPbobsCOM.BoObjectTypes.oInvoices);
                    oINV.CardCode = oDLN.CardCode;
                    for (int i = 0; i < oDLN.Lines.Count; i++)
                        oDLN.Lines.SetCurrentLine(i);
                        string str = oDLN.Lines.ItemCode;
                        if (i != 0)
                            oINV.Lines.Add();
                        //oINV.Lines.ItemCode = oDLN.Lines.ItemCode;
                        //oINV.Lines.Quantity = oDLN.Lines.Quantity;
                        oINV.Lines.BaseType = Convert.ToInt32(SAPbobsCOM.BoObjectTypes.oDeliveryNotes);
                        oINV.Lines.BaseEntry = oDLN.DocEntry;
                        oINV.Lines.BaseLine = oDLN.Lines.LineNum;
                        taxcode = oDLN.Lines.TaxCode;
if (DeliveryExpenseCount > 0)
                            for (int i = 0; i < DeliveryExpenseCount; i++)
                                oDLN.Expenses.SetCurrentLine(i);
                                if (i != 0)
                                    oINV.Expenses.Add();
                                //oINV.Expenses.ExpenseCode=i;
                                oINV.Expenses.ExpenseCode = oDLN.Expenses.ExpenseCode;
                                oINV.Expenses.LineTotal = oDLN.Expenses.LineTotal;
                                oINV.Expenses.TaxCode = oDLN.Expenses.TaxCode;
                                oINV.Expenses.BaseDocEntry = oDLN.DocEntry;
                                oINV.Expenses.BaseDocLine = oDLN.Expenses.LineNum;
                                oINV.Expenses.BaseDocType = 15;
int retVal = oINV.Add();
                    if (retVal != 0)
                        int lErrCode; string sErrCode;
                        modups.oCompany.GetLastError(out lErrCode, out sErrCode);
Any help will be appreciated..
Deepesh

Hi Gordon,
Thank you for your reply.But it didnt fix the problem.The only change of previous code with this one was oINV.Lines.Add() method is called in the last of the loop.But it wont fix issue.
Updated on 20/10/2011
I have found the issue.The issue is causing if we update the resulting invoice's expense lines.
If we copy the expense lines from delivery and update any line with an amount it works fine and resulting invoice has "Ordered Qty" in its lines. Code is
for (int i = 0; i < DeliveryExpenseCount; i++)
                    oDoc.Expenses.SetCurrentLine(i);
                    if (i != 0)
                        oINV.Expenses.Add();
                    string s = oDoc.Expenses.TaxCode;
                    oINV.Expenses.TaxCode = oDoc.Expenses.TaxCode;
                    oINV.Expenses.BaseDocEntry = oDoc.DocEntry;
                    oINV.Expenses.BaseDocLine = oDoc.Expenses.LineNum;
                    oINV.Expenses.BaseDocType = 15;
                    oINV.Expenses.LineTotal = oDoc.Expenses.LineTotal;
                    if (radioButton2.Checked == true && i == 0)
                        oINV.Expenses.LineTotal = oDoc.Expenses.LineTotal + Convert.ToDouble(txtExp.Text);
But if the delivery has no expense lines or we are adding a new expense line to the invoice while invoice creation from delivery , the resulting invoice does not have "Ordered Qty " in its lines..
Code is
if (DeliveryExpenseCount > 0)
                        oINV.Expenses.Add();
                    oINV.Expenses.ExpenseCode = 1;
                    oINV.Expenses.TaxCode = taxcode;
                    oINV.Expenses.LineTotal = Convert.ToDouble(txtExp.Text);
If I try to add lines
oINV.Expenses.BaseDocEntry = oDoc.DocEntry;
oINV.Expenses.BaseDocType = 15;
to the above code it may show either "Internal error" or " No matching records found".
Is this a bug in DI API?

How can I get my itunes onto my new laptop? Do I need to download itunes again or can I just copy it? My ipod classic has since been soaked in water and does not work so I cannot copy from there. Can anyone help?

How can I get my itunes onto my new laptop? Do I need to download itunes again or can I just copy it? My ipod classic has since been soaked in water and does not work so I cannot copy from there. Can anyone help?

You should copy everything from your old comptuer to your new one.

AnyConnect Profiles not getting downloaded.

Dear Team Members
I am facing the following issue in AnyConnect VPN deployment.
Requirement - Users should receive ANyConnect Profile, which has SCEP enabled, so that they can request a certificate from the organization Microsoft CA.
i already have a Certificate on ASA from the same CA and i want to use certificate authentication for ANyconnect.
ASA version is 8.4, i defined the flow as
1: Create User > bind it with a group policy > bind group policy with tunnel-group ( Connection profile)
2: Define a profile ( that has SCEp enabled & CA information URL etc..) and bind it with the group policy and also add it under
   webvpn
   AnyConnect Profile ....
when i initiate https://ASA_Ip_Address i authenticate with the username/password created above, Anyconnect is installed and i am connected, but profile is no tis downloaded, because i see no change on my Anyonnect Screen to request for a certificate. it remains the same, as no profile is available.
have followed the standard procedure,..    Plz guide me, what could be going wrong.
Any inputs from your side will be highly appreicated.
Thanks
Ahad

Hello Marvin
Thanks for your efforts for responding
As such i am using ASA 8.4, ASDM 6.47 & Anyconnect Package - Anyconnect-win-2.5.3055-k9.pkg ( i am using ver 2.5, because ver 3.0 does not support I Phones & Windows Mobile Phones).
Client PC - Windows 7 - 32 bit
1: i created Anyconnect profile using ASDM, it has simple settings to publish CA server details for SCEP, so that Anyconnect users can request the certificate through SCEP ( XML file attached)
2: As cheked profile folder is not available in
c:\program files \ cisco \ Cisco Anyconnect VPN Client
that simply means that profiles are not getting downloaded.
3: Configuration is attached & also the profile XML File.
you could try manually copying the xml onto a test client to see if it then behaves in the way you desire. - can u explain a bit more, how this testing can be done.
Plz let me know, what additional config is required.
Thanks in advanced
Ahad

I downloaded Magzter app button iPad 2 but when I buy magazines it is not getting downloaded but the same is getting downloaded in my iPod. Pl help. Magzter support is unable to help.

I downloaded Magzter app button iPad 2 but when I buy magazines it is not getting downloaded but the same is getting downloaded in my iPod. Pl help. Magzter support is unable to help.

You will not be able to see what version you are running until the iPad is activated. It will be in Settings>General>About >Version when you can get to the settings app.
The slider bar that you are describing sounds like the screen lock side switch and that has no bearing on setting up the iPad or connecting to WiFi.
Why don't you try rebooting your router? Unplug it for about 30 seconds and then plug it in again and see if the iPad will recognize and join the network.

I can no longer get to Facebook Via firefox It comes up loading in the tab but does not get any further one minute it was working the next it was,nt should I try uninstalling firefox then reinstall or does anyone know what could of happened thanks

# Question
I can no longer get to Facebook Via firefox It comes up loading in the tab but does not get any further one minute it was working the next it was,nt should I try uninstalling firefox then reinstall or does anyone know what could of happened thanks

* "Clear the Cache": Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
* "Remove the Cookies" from sites that cause problems: Tools > Options > Privacy > Cookies: "Show Cookies"
Start Firefox in [[Safe Mode]] to check if one of your add-ons is causing your problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
* Don't make any changes on the Safe mode start window.
See [[Troubleshooting extensions and themes]] and [[Troubleshooting plugins]]

Since upgrading to Maverick my iPhoto does not consistently download my Nikon or my Canon camera photos.

Since upgrading to Maverick my iPhoto does not consistently download my Nikon or my Canon camera photos. Occasionally it will recognize and download photos, most of the time though it hangs in "loading" mode with nothing downloaded. I've unplugged, replugged numerous times, tried a different USB port, tried the two cameras so it's not the camera or line that's the issue, turned the computer off, turned iphoto off, turned everything else off and stil nothing. I need my photos for my work and can't get to them, this seems to be an issue with Maverick AGAIN!!! Is there a fix? HELP! Thanks!

iPhoto Version 9.5.1
Thank you for your help Terence. I had 140 photos on my Nikon, none were viewable in iphoto, in Image Capture 5 were viewable, 135 weren't. I tried importing one to my desktop but it remained static and didn't move over. I just deleted all the photos on my camera, took a fresh photo and after waiting a good 4 minutes finally uploaded to both iphoto and Image Capture. As this took so long for one photo I'm wondering if the memory in my computer would impact the speed. I have 350GB used and 150GB left
By reformat the cards do you mean the flash card in the camera? I don't know how to do that, it's less that 6 months old.

JAR file does not get uploaded to client for my SERVLET generated APPLET

Some help please...
I have a servlet that generates the HTML code that contains an APPLET. This APPLET needs a JAR file that is listed under its ARCHIVE property. The SERVLET is in a JAR file that is in the same directory as the other needed JAR file. If I create a static HTML with the output of the SERVLET it works fine. But if go through Weblogic the needed JAR file does not get uploaded to the client so I get a java.lang.NoClassDefFoundError:and my APPLET does not load.
Q1: I am not sure what to put under the CODEBASE tag. I tried "." and I also tried "http://mymachine" but both did not work. I also tried without the CODEBASE tag. No luck. The SERVLET is bound to http://mymachine/servlet.
Q2: Does anyone have any suggestions on how to do this? Is there a way to force the browser to upload a certain JAR file?
Thanks...

It works!!
This is what I did:
The jar file in question was the weblogic.jar. I tried putting it under the lib directory of my war file but I had problems because the weblogic.jar contains other war files inside so when I tried to deploy my war file it also tried to deploy the inner war files which for some reason did not work. So I tried removing the war files from the weblogic.jar and this time I had no problems deploying my war file but I still could not find the classes I needed. So I tried moving the weblogic.jar to the root dir of my war file and it worked!! Now the trick here was: I did not set the CODEBASE AND I had the ARCHIVE paramenter set in TWO places like below:
<APPLET CODE = "marketmap.client.MarketMapApplet"
ARCHIVE = "weblogic.jar"
WIDTH = "657"
HEIGHT = "382"
ALIGN = "BOTTOM"
ALT = "APPLET tag not recognized">
</XMP>
<PARAM NAME = CODE VALUE = "MyApplet" >
<PARAM NAME = "type" VALUE="application/x-java-applet;version=1.2.2">
<PARAM NAME = "scriptable" VALUE="false">
<PARAM NAME = ARCHIVE VALUE="weblogic.jar">
</APPLET>
Actually if you do not place a parameter named ARCHIVE (at the end) it wil NOT work. I tried with multiple jar files listed and it works great too.
Anyway I figure I'd share. Thanks for the help too.
Lastly for people who choose not to upload the jar files to clients, you should look at the bea documentation on applets. It lists a classpath servlet that allows you to provide classes to the clients without having to force them to download the jar file.

Applet does not get loaded when viewed in a browser

Hi,
I have an applet,which works fine when I use appletviewer to see it. But from the browser, the applet does not get loaded.
An error appears at the bottom of the browser that load: class not found.
Any suggestions...please..
Thank you....
Pooja

If you are using Internet Explorer, you should check to see if your browser is set to use Sun's JRE that came with your download of the SDK. (If you didn't install the JRE, you need to go back and run that on your machine. You can check to see if you are using Java's runtime enviornment (JRE) in Internet Explorer by opening IE and going to Tools --> Internet Options... --> and then going to the Advanced tab. Scroll down and make sure the box next to Java Sun "use Java 2 for <applet>" is checked. If that option is not available, you need to install the JRE.
If that doesn't help, try using the HTML converter that comes with the SDK. It'll take your current HTML page, and you can customize it to force a download and/or usage of the JRE for applet viewing if for your particular browser.
Hope one of these helps!

SA520W does not get IP on optional WAN

We are using a SA520W as our primary router and have a fiber connection attached to the default WAN interface. We would like to improve our uptime using a secondary internet connection on the optional WAN interface.
We have bought a dovado tiny 4g router for this other connection. It acts as a dhcp server but the Cisco router does not get an IP from the dovado router. The router works as expected when connected to a normal computer. But somehow the cisco router doesnt get an IP.
I have also tried to set a static IP for the Cisco router but that didn't help either. The dovado router is setup do deliver ip in the range 192.168.0.2-254
Link is up but WAN state is Down. Any ideas?

Hello Christian,
What is the port configuration settings, set to 10/100/1000 Half or Full. If Auto try manually changing. Also you can try to clone the mac address, or set the mdi/mdix settings on the G4 router if possible.
Cisco Small Business Support Center
Randy Manthey
CCNA, CCNA - Security

Qosmio X500 - enternal monitor does not get a signal

Hi
its come a time when I need a external monitor to extend my desktop. I plugged in one of my monitors to the laptop. Qosmio sees it but the monitor does not get a signal. Tried a 2nd monitor and it does the same thing says cable not connected on 1 and power save on other.
I tested the monitors and cables on another laptop in the house and they work fine so its down to the laptop. Ive tried hdmi on a tv and that works fine, so seems to be just the vga as the laptop sees the monitor when connected does that mean the vga port is ok?
And could be something else? Any advice is welcome cheers.
John

Your posting is a bit confusing for me and I don't see clear structure there. What have you tested and the result is not clearly described.
>Ive tried hdmi on a tv and that works fine
How have you tested it? With your Qosmio or what?
Anyway, it is not easy to say what is wrong there. Try to test it with TV again. Connect your Qosmio to the TV using HDMI cable, switch to HDMI port on TV and use FN+F5 key combination to switch between LCD and TV.
Does it work?
>so seems to be just the vga as the laptop sees the monitor when connected does that mean the vga port is ok?
How to understand this? Is desktop shown on the screen when you use VGA port?

Cisco works LMS 3.0.1 does not archiever configuration for cisco 7201 router

Hi All,
We have Cisco works LMS 3.0.1 and it does not archiever configuration for cisco 7201 router.
Any help would be appriciated.
Thanks in advance
Samir

Hi,
*** Device Details for d0151-100 ***
Protocol ==> Unknown / Not Applicable
Selected Protocols with order ==> TFTP,SSH,HTTPS
Execution Result:
Unable to get results of job execution for device. Retry the job after increasing the job result wait time using the option:Resource Manager Essentials -> Admin -> Config Mgmt -> Archive Mgmt ->Fetch Settings
This is the error while doing syn archieve.
I am not sure about Rtr7000 version but we have latest Rtr7000.
Waiting for your kind reply.
Samir

My computer does not start download osx mountain lion what should I do, My computer does not start download osx mountain lion what should I do

My computer does not start download osx mountain lion what should I do, My computer does not start download osx mountain lion what should I do

What's installed on your computer? If you don't have Snow Leopard 10.6.6 or later then you cannot get Lion. If you already have Lion installed then you cannot re-download from the App Store until you have reinstalled Snow Leopard.

DACL does not get downloaded to Cisco Switch from ISE

Similar Messages

Maybe you are looking for