Df: cannot statvfs I/O error

Hi,
On giving the command df -k, I am getting the following error:
df: cannot statvfs /stage: I/O error
Here "stage" is a file system that is mounted in c0t5d0.
This particular hard disk is detected and seen using the "#format" command. I am not able to mount the file system /stage and I am also unable to create a new directory /stage.
The entry for c0t5d0 /stage is available in mnttab and vfstab.
This happened after a reboot of the server. Can anyone tell me what could cause this. Is there a hardware fault?
David

Shouldn't there be a section number too, as in c0t5d0s?.

Similar Messages

  • Testing ha-nfs in two node cluster (cannot statvfs /global/nfs: I/O error )

    Hi all,
    I am testing HA-NFS(Failover) on two node cluster. I have sun fire v240 ,e250 and Netra st a1000/d1000 storage. I have installed Solaris 10 update 6 and cluster packages on both nodes.
    I have created one global file system (/dev/did/dsk/d4s7) and mounted as /global/nfs. This file system is accessible form both the nodes. I have configured ha-nfs according to the document, Sun Cluster Data Service for NFS Guide for Solaris, using command line interface.
    Logical host is pinging from nfs client. I have mounted there using logical hostname. For testing purpose I have made one machine down. After this step files tem is giving I/O error (server and client). And when I run df command it is showing
    df: cannot statvfs /global/nfs: I/O error.
    I have configured with following commands.
    #clnode status
    # mkdir -p /global/nfs
    # clresourcegroup create -n test1,test2 -p Pathprefix=/global/nfs rg-nfs
    I have added logical hostname,ip address in /etc/hosts
    I have commented hosts and rpc lines in /etc/nsswitch.conf
    # clreslogicalhostname create -g rg-nfs -h ha-host-1 -N
    sc_ipmp0@test1, sc_ipmp0@test2 ha-host-1
    # mkdir /global/nfs/SUNW.nfs
    Created one file called dfstab.user-home in /global/nfs/SUNW.nfs and that file contains follwing line
    share -F nfs –o rw /global/nfs
    # clresourcetype register SUNW.nfs
    # clresource create -g rg-nfs -t SUNW.nfs ; user-home
    # clresourcegroup online -M rg-nfs
    Where I went wrong? Can any one provide document on this?
    Any help..?
    Thanks in advance.

    test1#  tail -20 /var/adm/messages
    Feb 28 22:28:54 testlab5 Cluster.SMF.DR: [ID 344672 daemon.error] Unable to open door descriptor /var/run/rgmd_receptionist_door
    Feb 28 22:28:54 testlab5 Cluster.SMF.DR: [ID 801855 daemon.error]
    Feb 28 22:28:54 testlab5 Error in scha_cluster_get
    Feb 28 22:28:54 testlab5 Cluster.scdpmd: [ID 489913 daemon.notice] The state of the path to device: /dev/did/rdsk/d5s0 has changed to OK
    Feb 28 22:28:54 testlab5 Cluster.scdpmd: [ID 489913 daemon.notice] The state of the path to device: /dev/did/rdsk/d6s0 has changed to OK
    Feb 28 22:28:58 testlab5 svc.startd[8]: [ID 652011 daemon.warning] svc:/system/cluster/scsymon-srv:default: Method "/usr/cluster/lib/svc/method/svc_scsymon_srv start" failed with exit status 96.
    Feb 28 22:28:58 testlab5 svc.startd[8]: [ID 748625 daemon.error] system/cluster/scsymon-srv:default misconfigured: transitioned to maintenance (see 'svcs -xv' for details)
    Feb 28 22:29:23 testlab5 Cluster.RGM.rgmd: [ID 537175 daemon.notice] CMM: Node e250 (nodeid: 1, incarnation #: 1235752006) has become reachable.
    Feb 28 22:29:23 testlab5 Cluster.RGM.rgmd: [ID 525628 daemon.notice] CMM: Cluster has reached quorum.
    Feb 28 22:29:23 testlab5 Cluster.RGM.rgmd: [ID 377347 daemon.notice] CMM: Node e250 (nodeid = 1) is up; new incarnation number = 1235752006.
    Feb 28 22:29:23 testlab5 Cluster.RGM.rgmd: [ID 377347 daemon.notice] CMM: Node testlab5 (nodeid = 2) is up; new incarnation number = 1235840337.
    Feb 28 22:37:15 testlab5 Cluster.CCR: [ID 499775 daemon.notice] resource group rg-nfs added.
    Feb 28 22:39:05 testlab5 Cluster.RGM.rgmd: [ID 375444 daemon.notice] 8 fe_rpc_command: cmd_type(enum):<5>:cmd=<null>:tag=<>: Calling security_clnt_connect(..., host=<testlab5>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
    Feb 28 22:39:05 testlab5 Cluster.CCR: [ID 491081 daemon.notice] resource ha-host-1 removed.
    Feb 28 22:39:17 testlab5 Cluster.RGM.rgmd: [ID 375444 daemon.notice] 8 fe_rpc_command: cmd_type(enum):<5>:cmd=<null>:tag=<>: Calling security_clnt_connect(..., host=<testlab5>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
    Feb 28 22:39:17 testlab5 Cluster.CCR: [ID 254131 daemon.notice] resource group nfs-rg removed.
    Feb 28 22:39:30 testlab5 Cluster.RGM.rgmd: [ID 224900 daemon.notice] launching method <hafoip_validate> for resource <ha-host-1>, resource group <rg-nfs>, node <testlab5>, timeout <300> seconds
    Feb 28 22:39:30 testlab5 Cluster.RGM.rgmd: [ID 375444 daemon.notice] 8 fe_rpc_command: cmd_type(enum):<1>:cmd=</usr/cluster/lib/rgm/rt/hafoip/hafoip_validate>:tag=<rg-nfs.ha-host-1.2>: Calling security_clnt_connect(..., host=<testlab5>, sec_type {0:WEAK, 1:STRONG, 2:DES} =<1>, ...)
    Feb 28 22:39:30 testlab5 Cluster.RGM.rgmd: [ID 515159 daemon.notice] method <hafoip_validate> completed successfully for resource <ha-host-1>, resource group <rg-nfs>, node <testlab5>, time used: 0% of timeout <300 seconds>
    Feb 28 22:39:30 testlab5 Cluster.CCR: [ID 973933 daemon.notice] resource ha-host-1 added.

  • OSB: Cannot acquire data source error while using JCA DBAdapter in OSB

    Hi All,
    I've entered 'Cannot acquire data source' error while using JCA DBAdapter in OSB.
    Error infor are as follows:
    The invocation resulted in an error: Invoke JCA outbound service failed with application error, exception: com.bea.wli.sb.transports.jca.JCATransportException: oracle.tip.adapter.sa.api.JCABindingException: oracle.tip.adapter.sa.impl.fw.ext.org.collaxa.thirdparty.apache.wsif.WSIFException: servicebus:/WSDL/DBAdapter1/RetrievePersonService [ RetrievePersonService_ptt::RetrievePersonServiceSelect(RetrievePersonServiceSelect_inputParameters,PersonTCollection) ] - WSIF JCA Execute of operation 'RetrievePersonServiceSelect' failed due to: Could not create/access the TopLink Session.
    This session is used to connect to the datastore.
    Caused by Exception [EclipseLink-7060] (Eclipse Persistence Services - 2.0.2.v20100323-r6872): org.eclipse.persistence.exceptions.ValidationException
    Exception Description: Cannot acquire data source [jdbc/soademoDatabase].
    Internal Exception: javax.naming.NameNotFoundException: Unable to resolve 'jdbc.soademoDatabase'. Resolved 'jdbc'; remaining name 'soademoDatabase'.
    ; nested exception is:
    BINDING.JCA-11622
    Could not create/access the TopLink Session.
    This session is used to connect to the datastore.
    JNDI Name for the Database pool: eis/DB/soademoDatabase
    JNDI Name for the Data source: jdbc/soademoDatabase
    I created a basic DBAdapter in JDeveloper, got the xsd file, wsdl file, .jca file and the topLink mapping file imported them into OSB project.
    Then I used the .jca file to generate a business service, and tested, then the error occurs as described above.
    Login info in RetrievePersonService-or-mappings.xml
    <login xsi:type="database-login">
    <platform-class>org.eclipse.persistence.platform.database.oracle.Oracle9Platform</platform-class>
    <user-name></user-name>
    <connection-url></connection-url>
    </login>
    jca file content are as follows:
    <adapter-config name="RetrievePersonService" adapter="Database Adapter" wsdlLocation="RetrievePersonService.wsdl" xmlns="http://platform.integration.oracle/blocks/adapter/fw/metadata">
    <connection-factory location="eis/DB/soademoDatabase" UIConnectionName="Connection1" adapterRef=""/>
    <endpoint-interaction portType="RetrievePersonService_ptt" operation="RetrievePersonServiceSelect">
    <interaction-spec className="oracle.tip.adapter.db.DBReadInteractionSpec">
    <property name="DescriptorName" value="RetrievePersonService.PersonT"/>
    <property name="QueryName" value="RetrievePersonServiceSelect"/>
    <property name="MappingsMetaDataURL" value="RetrievePersonService-or-mappings.xml"/>
    <property name="ReturnSingleResultSet" value="false"/>
    <property name="GetActiveUnitOfWork" value="false"/>
    </interaction-spec>
    </endpoint-interaction>
    </adapter-config>
    RetrievePersonService_db.wsdl are as follows:
    <?xml version="1.0" encoding="UTF-8"?>
    <WL5G3N0:definitions name="RetrievePersonService-concrete" targetNamespace="http://xmlns.oracle.com/pcbpel/adapter/db/KnowledeMgmtSOAApplication/AdapterJDevProject/RetrievePersonService" xmlns:WL5G3N0="http://schemas.xmlsoap.org/wsdl/" xmlns:WL5G3N1="http://xmlns.oracle.com/pcbpel/adapter/db/KnowledeMgmtSOAApplication/AdapterJDevProject/RetrievePersonService" xmlns:WL5G3N2="http://schemas.xmlsoap.org/wsdl/soap/">
    <WL5G3N0:import location="RetrievePersonService.wsdl" namespace="http://xmlns.oracle.com/pcbpel/adapter/db/KnowledeMgmtSOAApplication/AdapterJDevProject/RetrievePersonService"/>
    <WL5G3N0:binding name="RetrievePersonService_ptt-binding" type="WL5G3N1:RetrievePersonService_ptt">
    <WL5G3N2:binding style="document" transport="http://www.bea.com/transport/2007/05/jca"/>
    <WL5G3N0:operation name="RetrievePersonServiceSelect">
    <WL5G3N2:operation soapAction="RetrievePersonServiceSelect"/>
    <WL5G3N0:input>
    <WL5G3N2:body use="literal"/>
    </WL5G3N0:input>
    <WL5G3N0:output>
    <WL5G3N2:body use="literal"/>
    </WL5G3N0:output>
    </WL5G3N0:operation>
    </WL5G3N0:binding>
    <WL5G3N0:service name="RetrievePersonService_ptt-bindingQSService">
    <WL5G3N0:port binding="WL5G3N1:RetrievePersonService_ptt-binding" name="RetrievePersonService_ptt-bindingQSPort">
    <WL5G3N2:address location="jca://eis/DB/soademoDatabase"/>
    </WL5G3N0:port>
    </WL5G3N0:service>
    </WL5G3N0:definitions>
    Any suggestion is appricated .
    Thanks in advance!
    Edited by: user11262117 on Jan 26, 2011 5:28 PM

    Hi Anuj,
    Thanks for your reply!
    I found that the data source is registered on server soa_server1 as follows:
    Binding Name: jdbc.soademoDatabase
    Class: weblogic.jdbc.common.internal.RmiDataSource_1033_WLStub
    Hash Code: 80328036
    toString Results: ClusterableRemoteRef(8348400613458600489S:10.2.1.143:[8001,8001,-1,-1,-1,-1,-1]:base_domain:soa_server1 [8348400613458600489S:10.2.1.143:[8001,8001,-1,-1,-1,-1,-1]:base_domain:soa_server1/291])/291
    Binding Name: jdbc.SOADataSource
    Class: weblogic.jdbc.common.internal.RmiDataSource_1033_WLStub
    Hash Code: 92966755
    toString Results: ClusterableRemoteRef(8348400613458600489S:10.2.1.143:[8001,8001,-1,-1,-1,-1,-1]:base_domain:soa_server1 [8348400613458600489S:10.2.1.143:[8001,8001,-1,-1,-1,-1,-1]:base_domain:soa_server1/285])/285
    I don't know how to determine which server the DBAdapter is targetted to.
    But I found the following information:
    Under Deoloyment->DBAdapter->Monitoring->Outbound Connection Pools
    Outbound Connection Pool Server State Current Connections Created Connections
    eis/DB/SOADemo AdminServer Running 1 1
    eis/DB/SOADemo soa_server1 Running 1 1
    eis/DB/soademoDatabase AdminServer Running 1 1
    eis/DB/soademoDatabase soa_server1 Running 1 1
    The DbAdapter is related to the following files:
    C:\ Oracle\ Middleware\ home_11gR1\ Oracle_SOA1\ soa\ connectors\ DbAdapter. rar
    C:\ Oracle\ Middleware\ home_11gR1\ Oracle_SOA1\ soa\ DBPlan\ Plan. xml
    I unzipped DbAdapter.rar, opened weblogic-ra.xml and found that there's only one data source is registered:
    <?xml version="1.0"?>
    <weblogic-connector xmlns="http://www.bea.com/ns/weblogic/90">
    <enable-global-access-to-classes>true</enable-global-access-to-classes>
    <outbound-resource-adapter>
    <default-connection-properties>
    <pool-params>
    <initial-capacity>1</initial-capacity>
    <max-capacity>1000</max-capacity>
    </pool-params>
    <properties>
    <property>
    <name>usesNativeSequencing</name>
    <value>true</value>
    </property>
    <property>
    <name>sequencePreallocationSize</name>
    <value>50</value>
    </property>
    <property>
    <name>defaultNChar</name>
    <value>false</value>
    </property>
    <property>
    <name>usesBatchWriting</name>
    <value>true</value>
    </property>
    <property>
    <name>usesSkipLocking</name>
    <value>true</value>
    </property>
    </properties>
              </default-connection-properties>
    <connection-definition-group>
    <connection-factory-interface>javax.resource.cci.ConnectionFactory</connection-factory-interface>
    <connection-instance>
    <jndi-name>eis/DB/SOADemo</jndi-name>
              <connection-properties>
                   <properties>
                   <property>
                   <name>xADataSourceName</name>
                   <value>jdbc/SOADataSource</value>
                   </property>
                   <property>
                   <name>dataSourceName</name>
                   <value></value>
                   </property>
                   <property>
                   <name>platformClassName</name>
                   <value>org.eclipse.persistence.platform.database.Oracle10Platform</value>
                   </property>
                   </properties>
              </connection-properties>
    </connection-instance>
    </connection-definition-group>
    </outbound-resource-adapter>
    </weblogic-connector>
    Then I decided to use eis/DB/SOADemo for testing.
    For JDeveloper project, after I deployed to weblogic server, it works fine.
    But for OSB project referencing wsdl, jca and mapping file from JDeveloper project, still got the same error as follows:
    BEA-380001: Invoke JCA outbound service failed with application error, exception:
    com.bea.wli.sb.transports.jca.JCATransportException: oracle.tip.adapter.sa.api.JCABindingException: oracle.tip.adapter.sa.impl.fw.ext.org.collaxa.thirdparty.apache.wsif.WSIFException: servicebus:/WSDL/DBAdapterTest/DBReader [ DBReader_ptt::DBReaderSelect(DBReaderSelect_inputParameters,PersonTCollection) ] - WSIF JCA Execute of operation 'DBReaderSelect' failed due to: Could not create/access the TopLink Session.
    This session is used to connect to the datastore.
    Caused by Exception [EclipseLink-7060] (Eclipse Persistence Services - 2.0.2.v20100323-r6872): org.eclipse.persistence.exceptions.ValidationException
    Exception Description: Cannot acquire data source [jdbc/SOADataSource].
    Internal Exception: javax.naming.NameNotFoundException: Unable to resolve 'jdbc.SOADataSource'. Resolved 'jdbc'; remaining name 'SOADataSource'.
    ; nested exception is:
    BINDING.JCA-11622
    Could not create/access the TopLink Session.
    This session is used to connect to the datastore.
    Caused by Exception [EclipseLink-7060] (Eclipse Persistence Services - 2.0.2.v20100323-r6872): org.eclipse.persistence.exceptions.ValidationException
    Exception Description: Cannot acquire data source [jdbc/SOADataSource].
    Internal Exception: javax.naming.NameNotFoundException: Unable to resolve 'jdbc.SOADataSource'. Resolved 'jdbc'; remaining name 'SOADataSource'.
    You may need to configure the connection settings in the deployment descriptor (i.e. DbAdapter.rar#META-INF/weblogic-ra.xml) and restart the server. This exception is considered not retriable, likely due to a modelling mistake.
    It almost drive me crazy!!:-(
    What's the purpose of 'weblogic-ra.xml' under the folder of 'C:\Oracle\Middleware\home_11gR1\Oracle_OSB1\lib\external\adapters\META-INF'?
    ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

  • Error: You cannot login because an error occurred while retrieving the login URL. (WW

    Situation is this.. was using 8.1.6 EE and Oracle Portal.. was able to get the Oracle Portal page up and after a while the application died.. this happened numerous times. Found in one of these forums that a bug existed (UTL_HTTP) and recommended going to 8.1.7 EE because of a patch. I migrated my 8.1.6 EE to 8.1.7 EE(made sure procedures & packages were valid). I'm able to bring up the Oracle Portal page but when I go to login I get this:
    Error: You cannot login because an error occurred while retrieving the login URL. (WWC-41441)
    Thoughts?

    Hi,
    I ran ssodatan again and got the following error:
    ERROR: Setting Login Server Partner App
    ORA-06508: PL/SQL: could not find program unit being called
    I then found out that the wwsec_sso_enabler_private in the SSO
    schema is invalid and this was causing the above error. I tried
    recompiling the package but got the following error:
    Errors for PACKAGE BODY WWSEC_SSO_ENABLER_PRIVATE:
    LINE/COL ERROR
    151/6 PL/SQL: SQL Statement ignored
    151/13 PLS-00320: the declaration of the type of this
    expression is incomplete or malformed
    151/20 PLS-00336: non-object-table "SECI" illegal in this
    context
    160/4 PL/SQL: SQL Statement ignored
    643/6 PL/SQL: SQL Statement ignored
    643/13 PLS-00320: the declaration of the type of this
    expression is incomplete or malformed
    643/20 PLS-00336: non-object-table "SECI" illegal in this
    context
    LINE/COL ERROR
    651/4 PL/SQL: SQL Statement ignored
    713/4 PL/SQL: SQL Statement ignored
    713/50 PLS-00382: expression is of wrong type
    745/3 PL/SQL: SQL Statement ignored
    746/10 PLS-00389: table, view or alias name "ENBCONFIG" not
    allowed in this context
    The same package in the Portal schema is valid. Will an
    export of this package from a working instance and an import into
    the above instance solve this problem?
    Thanks and Regards,
    Rupesh

  • Cannot update.  Get error message 1648, "no valid sequence could be found for the set of patches."

    Cannot update.  Get error message 1648, "no valid sequence could be found for the set of patches."

    Uninstall the corrupt Reader version using http://labs.adobe.com/downloads/acrobatcleaner.html then download and install the latest Reader from http://get.adobe.com/reader/enterprise/

  • Cannot view video get error message and only sound.

    cannot view video, get error message and sound only. Message  Error Code:c000005, address:2568b7ab

    I am just finally posting a reply. Looks as though the sound card went out. I was told that I could purchase a new open and install myself. I did not do that, but rather my step-dad just decided it was time to buy a new Mac Mini.

  • IPod cannot be updated Unknown error-48

    Help - have installed iTunes 7.0.1 and am trying to keep ALL the music on my iPod so have tried to set the options to manual update. But although the computer senses the iPod is connected, when I try and drag new files to my iPod, I get the message "iPod cannot be updated Unknown error-48" Any advice gratefully received

    Hey!
    Just an update since last week.
    Still comes up with the "Unknown Error_48" when coupled to the Mac.Doesn't sync to iTunes and says it's upto date in the summary.Never had any issues like this (until iTunes 7 and 1.2).Kinda renders the whole iPod thing a bit useless.
    Being able to update the library on your Pod is essential.Otherwise what's the point?My Pod still 'works'but not quite the way Apple intended I think.
    SORT IT OUT APPLE!!
    John
    iMac G5 1.8GHz 20"   Mac OS X (10.4.7)   ipod 30GB Video Black v.1.2 Agent 18 Case iTunes 7.0 Bose Sounddock
    iMac G5 1.8GHz 20"   Mac OS X (10.4.7)   ipod 30GB Video Black v.1.2 Agent 18 Case iTunes 7.0 Bose Sounddock
    iMac G5 1.8GHz 20"   Mac OS X (10.4.7)   ipod 30GB Video Black v.1.2 Agent 18 Case iTunes 7.0 Bose Sounddock

  • TS1424 cannot connect to itunes error messageinformation from sync services Reconnect or try again later

    cannot  conect to itunes error message "itunes was unable to load data class information from sync services Reconnect or try later"
    i hate itunes!!!!!!!!!!!!!!!

    Hello tonyb2910,
    The following article should be just the thing to put Sync Services down and get your iPhone working smoothly with iTunes again.
    iTunes for Windows: "Unable to load data class" or "Unable to load provider data" sync services alert
    http://support.apple.com/kb/TS2690
    Cheers,
    Allen

  • How do i solve - cannot access web server - error message when creating a project in 4.5 with PHP

    How do i solve - cannot access web server - error message when creating a project in 4.5 with PHP

    Screenshot of how it looks when i try to show a ms access form inside a iframe:
    http://oi58.tinypic.com/2vj4ish.jpg

  • Help - "Cannot copy file: Data error (Cyclic Redundancy Check)"

    Hey there,
    I'm having problems with my Zen Mosaic EZ00. Up until a few weeks ago it has been working fine however, since then, has begun to show the error message? "Cannot copy file: Data error (Cyclic Redundancy Check)" whenever I try to copy files on to it. I have tried the recovery software available and it only updated the firmware. Some files do occasionally (and very occasionally) copy but usually it shows the error message and cancels the copy.
    I would really appreciate if anyone could help me with this?
    Many thanks :smileytongue:

    sorry for the double post!
    ive just realised that my ipod isnt actually charging, its just got the orange light blinking!
    not too sure what is going on now!
    lol

  • Anyone else have the issue where, after the 8,3 upgrade, you cannot access more than 1 exchange account on your iPhone? This is annoying to me as I need to access 4 daily and cannot due to this error.

    Anyone else have the issue where, after the 8,3 upgrade, you cannot access more than 1 exchange account on your iPhone? This is annoying to me as I need to access 4 daily and cannot due to this error.
    The first one, my private home email, works fine. With the other 3, I get the message "Cannot get mail: The connection to the server failed"
    All were working fine before the 8.3 upgrade. I did try the old trick of making one minor change on the account and resaving, but that did not change anything. I even deleted my work account and re-entered it from scratch, but again, sadly, no luck. For the time being, I am successfully getting the email via IMAP, but this ***** compared to exchange. Anyone have any idea what is happening or if a fix is in the works?

    Well, the one set up on exchange 2k3 is now working fine, although no changes were made on either the iPhone or the exchange side, so that's fun, but it still is throwing errors when connecting to the other 2 exchange accounts. The common elements are that both non-functioning exchange accounts are google apps for business accounts. So is one of the ones that's working, by the way. The settings on both accounts are the same as the one that's working, and both worked fine before the 8.3 upgrade. I have no issue accessing both of these accounts on my ipad which is currently on 8.2.x. If it's not the iphone OS at fault, I'm at a loss as to what it could be.

  • TS1425 5th Generation Nano iPod.  The iPod syncs on iTunes when I connect it to my MAC, but when I try to add a song from iTunes to the iPod, I receive the message "Cannot be synced, unknown error occurred (1039)

    5th generation iPod Nano - iPod syncs with my iTunes and I can see it in iTunes, but when I try to move a song from my iTunes to the iPod I get an error message "Cannot by synced, Unknown error occurred (1039).  System works fine with my 4th generation iPod Nano.  I'm afraid to "RESET" my iPod because I may not be able to restore my music and videos afterwards.

    Hello Ventanilla 97,
    I agree with planb77 with recreating your itunes library. That will fix your issue. If you would like more step by step info go here:
    https://discussions.apple.com/message/15028503#15028503
    Hope this helps.
    ~Julian

  • IPad1 stuck in recovery mode with and ITunes cannot restore with an error code of 11?

    I tried to update to IOS 4.3.4 today but now my iPad1 stuck in recovery mode with and ITunes cannot restore with an error code of 11?
    (With the old discussion groups it was easy to see where other people had similar problems, these new groups seems clunky in comparison)

    OK, fixed it by using SHIFT+RESTORE to load the iPad1,1_4.3.4_8K2_Restore.ipsw  file in directly from the
    C:\Documents and Settings\<user name>\Application Data\Apple Computer\iTunes\iPad Software Updates
    folder.
    No idea why the upgrade to 4.3.3 failed in the first place and no idea why iTunes was not clever enough to just do it by itself when it detected that there was a problem in the first place.

  • Has anyone solved the notorious "Cannot Connect to Youtube" Error?

    Whenever I open the Youtube app I get "Cannot connect to Youtube" no matter what why network I'm on no matter how I'm connected. EVERYTHING else on the phone works perfectly.
    Even the youtube website works fine via safari but the videos WILL NOT PLAY.
    I have tried all the hit or miss speculative solutions that people claim work for them:
    *Change the date past the year 2030 and then back again.
    *Hard reset the phone
    *Power on power off
    *Reset network settings
    *Full reset of settings
    *Trying different networks
    *Connecting to the computer and synching the phone and the apps
    None of these work. Some people claim success with one or more of the different methods above but it doesn't work for me and many others. This issue has been going on for a LONG time and it is WIDESPREAD (just search this forum or the internet at large via google and you will see). It spans across multiple devices (iPhone and iPod Touch alike) and multiple software versions across multiple generations of the devices. I find it appalling that Apple is silent on this gaping bug.
    Does anyone have a solution? Does anyone know how to get Apple to DO SOMETHING?
    Thanks.

    Are you senior executives in Apple's cost cutting in the customer service and quality control department or what?
    +If it works fine on your friends iPhones when they come over it does not sound like a bug, it sounds like a problem with your iPhone.+
    It IS a problem with my iPhone. Anything that causes one of the built in operating applications to fail frequently under normal use whether or not it happens on every device consistently is absolutely by definition a bug.
    +Explain why the alleged bug is not on every iPhone then ? This is the bit that you fail to explain in every post you make.+
    It may not be on every phone but it definitely is on MANY, what triggers it is unknown. Microsoft releases hundreds if not thousands of bug fixes every year. Why don't all the HUNDREDS of millions of Windows users all experience every single bug? By your logic none of these bugs exists because every single user doesn't experience them. I can't remember the last time I personally experienced one of the bugs that all these mountains of bug fixes I download through windows update automatically correct so I guess none of those bugs actually exist.
    +I have read a lot more articles by people who think the world is flat and that means nothing. There are 10 million odd iPhones, 50 people isn't a conclusive fault. explain why 9,999,950 of them appear to work fine?+
    There are thousands of people with this problem. With a problem like this a person with even shred of intellect would read a few posts from a few different sources and come to an informed conclusion on the issue rather than dedicate the next six months of their life to reading every single thing ever written about it. Once you see the pattern is exactly the same even in 10 plus posts and it's obvious there are THOUSANDS more you can conclude it's not an isolated incident.
    +Thats hardly conclusive - there are youtube video's on how to make an egg custard but that doesn't mean nobody can make one without instruction, or that all egg custards made are defective somehow.+
    Inappropriate and just flat out wrong analogy. If there was a "how to make custard when it fails in a specific way consistently" then your analogy would be appropriate. The "how to FIX x" youtube video is not analogous to "how to use your iphone" or "how to do x." In any event comparing egg custard to an iphone is clearly apples to oranges - or more like apples to nuclear reactors.
    +Don't bother quoting Google Stats - you can get hits on every search string you put in, and one post gets copied again and again and comes up as multiple hits.+
    Really? I had no idea google one of the most successful companies in the world had such a faulty and defective search engine that it gives phony results. Have you told them? Maybe they will hire you to fix it.
    You may get SOME hits for any garbage you put in (not really ANY but a lot of garbage) but they won't be very many.
    "asldfjla adfkjdsafd" - 0 hits (looks like you're wrong again)
    "random string of nonsense searching" - 22,500 hits
    "iphone "compass not working"" - 7,700 hits
    "ipod "calendar not working"" - 4,570 hits
    "iphone "calendar not working"" - 8,490 hits
    "iphone "stocks not working"" - 3 hits (really google makes too many phony hits? Are you sure you dont' mean not enough - do you really believe only 3 people ever uttered these words on the ENTIRE internet???)
    "iphone "calculator not working"" - 23,900 hits
    "iphone "cannot connect to youtube"" - 980,000 hits
    "ipod "cannot connect to youtube"" - 859,000 hits
    Yep I see it, it's settled now. It definitely must be something I just made up. Looks like nobody else is having that problem. Must not mean a thing that there are more than 100 times more articles on this built in app than a couple others I picked at random. I'm glad you settled this for me how google is broken and only my iphone is misconfigured and the "cannot connect to youtube" error is not widespread.

  • The NLS operation failed because the registry key Control Panel\International\User Profile cannot be opened. Error code is 2. Error message: The system cannot find the file specified.

    H,
    Since upgrading Windows server 2008 R2 to Server 2012 Standard edition, we get this repetitious critical error in the event log:
    Event 1001
    Op Code NLS initialization
    The NLS operation failed because the registry key Control Panel\International\User Profile cannot be opened. Error code is 2. Error message: The system cannot find the file specified.
    We originally found that the regional date settings after changing them in regional settings (DD/MM/YYYY) and they did not inherit properly from the upgrade but they are ok now. 
    I've looked at HKCU\.Default\Control Panel\International and nothing looks obviously wrong. Country codes, time & date formats are correct.
    How do we ascertain the  cause of this error and the specific registry key that might be problematic?

    Hi,
    This could be caused by firewall rules or security softwares.
    http://www.tomshardware.com/forum/242579-44-hkcu-control-panel-international-opened
    And in addition, the fix is worth a try.
    Nothing happens when you double-click "Region" in Control Panel 
    http://support.microsoft.com/kb/2958845
    Please Note: Since the first web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.

Maybe you are looking for