DHCP Opt 43 & 60 support

Hello all,
I am trying to provide DHCP services to Cisco 1242AG APs via the PIX firewall.
Does anyone know if the PIX 515 with IOS version 6.3(4) supports the proper syntax for DHCP option 43 and 60.
Although I enter option 43 with dotted notation, the firewall strips out the delimiters.
On option 60 when trying to input "Cisco AP c1240", the firewall does not like quotes or spaces.
Is there a work around to creating these options in the proper syntax?
TIA,
Mike

I hate to say, but that is a bad design. Back around two or three years ago when Cisco just bought Aerospace, that was and option for a design. Now it is best practice to avoid that.... especially with voice. What I have done is break up the floors to a wlc. Like if you had 6 floors, wlc would handle floor 1 & 2, wlc 2 floor 3 & 4, wlc 3 floor 5 & 6. If you don't thinks this is a good idea, try to find a doc now that tells you to do a salt n pepper design. its up to you though, just giving you my opinion.
You should start a new thread just to get more feedback before your rollout. Title it Salt & Pepper design for voice. It is a good topic.

Similar Messages

  • Does WLC release 7.6 support internal DHCP when AP and client SSO is configured?

    Hi,
    I currently have 5508 WLCs running on release 7.6 and they are to be configured in 1:1 HA mode. Would like to know if internal DHCP is supported if AP and client SSO is to be configured.
    Thanks in advance.

    Unfortunately, till date no AirOS release supports Internal DHCP when AP SSO is configured.
    For details, check HA Deployment Guide. It says following :
    "Internal DHCP is not supported when SSO is enabled."
    -Thanks
    Vinod

  • How to configure DNS to support ipv4 and ipv6

    I have a 2008 r2 domain controller in my lab.
    i'm doing Exchange 2007, 2010 and 2013. I have mix Windows 2008 r2 servers for other applications.
    i'm running into issues where i'm thinking it is time to have both IPV4 & IPV6 to run on all lab machines.
    I can't get a clear picture on how to accomplish a mix environment. in the DNS administrator do I create a new "reverze lookup zone" with only the IPV6? or do I have to create a new record in the "forward lookup zone" to with both IPV4
    & IPV6 which the later points to the new "reverse lookup zone".
    I see a lot of internet article but little on "how to".
    or on the DC should I enable the DHCP role to support the IPV6?

    1. You assign an IPv6 address to the domain controller/DNS server
    One method is letting this site (legitimate) create a random private IPv6 range for you:
    http://www.simpledns.com/private-ipv6.aspx
    For example:
    fd06:fcde:8b4e:d6bd:xxxx:xxxx:xxxx:xxxx
    You can configure the x's like this (you cannot leave the x's there):
    fd06:fcde:8b4e:d6bd:0000:0000:0000:0001
    If you close and open IPv6 properties, or do an "ipconfig /all" you'll see that the IPv6 is abbreviated as follows:
    fd06:fcde:8b4e:d6bd::1
    That's normal.
    If you look in your forward lookup zone, you'll now see this IPv6 address (you may have to register that manually - ipconfig /registerdns - but it seemed to happen automatically for me.
    So there is no need to create a separate forward lookup zone for IPv6.
    OK, but what about the reverse zone?
    2. Create reverse lookup
    In DNS Manager (what you call administrator), right-click on reverse lookup zone, select New Zone, click, Next, Next (default values are fine) until you choose between IPv6 and IPv4. Selecft IPv6 of course.
    Then enter your prefix as shown here:
    That's it. The reverse lookup information is configured automatically (your prefix " backwards").
    Now, unlike with the forward lookup zone, my domain controller does not seem to be registering its name in the reverse IPv6 zone: there's only the SOA and NS record.
    But that's another question.
    Please mark as helpful if you find my contribution useful or as an answer if it does answer your question. That will encourage me - and others - to take time out to help you.

  • Netboot a Apple PC on a Windows DHCP server.

    I need to set up our Windows DHCP servers to support netboot across subnets for our Apple machines.  I am unable to find a clear list of what scope options and what data they need online.  Can someone provide me this information?
    Thanks!
    Shawn

    Hi,
    Although Microsoft does not recommend this method, you can use the following DHCP options to direct PXE clients to an appropriate NBP to download:
    • Option 60 = client identifier. You should set this to the string PXEClient. Note that this only
      applies if DHCP is on the same server as Windows Deployment Services.
    • Option 66 = boot server host name
    • Option 67 = boot file name
    Managing Network Boot Programs
    http://technet.microsoft.com/en-us/library/cc732351%28v=ws.10%29.aspx
    The similar thread:
    WDS,PXE & DHCP
    http://social.technet.microsoft.com/Forums/en-US/cb02c4ac-0ab6-401d-96d3-bd0d61e6eee3/wdspxe-dhcp?forum=configmgrosd
    MDT/WDS PXE Deployment - DHCP Options for both x64 and x86
    http://social.technet.microsoft.com/Forums/en-US/6f7a1af4-0dd8-4af6-8d2a-1e9ee16a8f37/mdtwds-pxe-deployment-dhcp-options-for-both-x64-and-x86?forum=mdt
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Config DHCP service on AIRONET 1040 autonomous

    Hello,
    I tried to configure DHCP service that will supply addresses for the wifi users.
    I configured:
    ip dhcp pool sefi
       network 192.168.42.0 255.255.255.0
       dns-server 8.8.8.8
       default-router 192.168.42.1
    How can I connect this DHCP service to the Dot11Radio0 interface or to the dot11 SSID??
    Thanks

     Configuring DHCP
    WLANs can be configured to use the same or different Dynamic Host Configuration Protocol (DHCP) servers or no DHCP server. Two types of DHCP servers are available: internal and external.
    Internal DHCP Server
    The controllers contain an internal DHCP server. This server is typically used in branch offices that do not already have a DHCP server. The wireless network generally contains 10 access points or fewer, with the access points on the same IP subnet as the controller. The internal server provides DHCP addresses to wireless clients, direct-connect access points, appliance-mode access points on the management interface, and DHCP requests that are relayed from access points. Only lightweight access points are supported. When you want to use the internal DHCP server, you must set the management interface IP address of the controller as the DHCP server IP address.
    DHCP option 43 is not supported on the internal server. Therefore, the access point must use an alternative method to locate the management interface IP address of the controller, such as local subnet broadcast, DNS, priming, or over-the-air discovery.
    Note See the Chapter 8 "Controlling Lightweight Access Points," or the Controller Deployment Guide at this URL for more information on how access points find controllers:
    http://www.cisco.com/en/US/products/ps6366/prod_technical_reference_list.html
    Note A internal DHCP server pool will only serve the wireless clients of that controller, not clients of other controllers. Also, internal DHCP server can only serve wireless clients and not wired clients.
    Note DHCP required state can cause traffic to not be forwarded properly if a client is deauthenticated or removed. To overcome this, ensure that DHCP required state is always in disabled state.
    External DHCP Servers
    The operating system is designed to appear as a DHCP Relay to the network and as a DHCP server to clients with industry-standard external DHCP servers that support DHCP Relay, which means that each controller appears as a DHCP Relay agent to the DHCP server and as a DHCP server at the virtual IP address to wireless clients.
    Because the controller captures the client IP address obtained from a DHCP server, it maintains the same IP address for that client during intra-controller, inter-controller, and inter-subnet client roaming.
    DHCP Assignment
    You can configure DHCP on a per-interface or per-WLAN basis. The preferred method is to use the primary DHCP server address assigned to a particular interface.
    Per-Interface Assignment
    You can assign DHCP servers for individual interfaces. The management interface, AP-manager interface, and dynamic interfaces can be configured for a primary and secondary DHCP server, and the service-port interface can be configured to enable or disable DHCP servers.
    Note See the Chapter 10 "Managing Controller Software and Configurations," for information on configuring the controller's interfaces.
    Per-WLAN Assignment
    You can also define a DHCP server on a WLAN. This server will override the DHCP server address on the interface assigned to the WLAN.
    Security Considerations
    For enhanced security, we recommend that you require all clients to obtain their IP addresses from a DHCP server. To enforce this requirement, all WLANs can be configured with a DHCP Addr. Assignment Required setting, which disallows client static IP addresses. If DHCP Addr. Assignment Required is selected, clients must obtain an IP address via DHCP. Any client with a static IP address is not be allowed on the network. The controller monitors DHCP traffic because it acts as a DHCP proxy for the clients.
    Note WLANs that support management over wireless must allow management (device-servicing) clients to obtain an IP address from a DHCP server. See the "Using Management over Wireless" section for instructions on configuring management over wireless.
    If slightly less security is tolerable, you can create WLANs with DHCP Addr. Assignment Required disabled. Clients then have the option of using a static IP address or obtaining an IP address from a designated DHCP server.
    Note DHCP Addr. Assignment Required is not supported for wired guest LANs.
    You are also allowed to create separate WLANs with DHCP Addr. Assignment Required disabled; then define the primary / secondary DHCP server as 0.0.0.0 on the interface assigned to the WLAN. These WLANs drop all DHCP requests and force clients to use a static IP address. Note that these WLANs do not support management over wireless connections.
    Note See Chapter 4 "Configuring Controller Settings," for instructions on globally configuring DHCP proxy.
    Note If you want to specify a static IP address for an access point rather than having one assigned automatically by a DHCP server, see the "Configuring a Static IP Address on a Lightweight Access Point" section for more information.
    This section provides both GUI and CLI instructions for configuring DHCP.
    Using the GUI to Configure DHCP
    To configure DHCP using the GUI, follow these steps:
    Step 1 Follow the instructions in the "Using the GUI to Configure the Management, AP-Manager, Virtual, and Service-Port Interfaces" section or "Using the GUI to Configure Dynamic Interfaces" section to configure a primary DHCP server for a management, AP-manager, or dynamic interface that will be assigned to the WLAN.
    Note When you want to use the internal DHCP server, you must set the management interface IP address of the controller as the DHCP server IP address.
    Step 2 Choose WLANs to open the WLANs page.
    Step 3 Click the ID number of the WLAN for which you wish to assign an interface. The WLANs > Edit (General) page appears.
    Step 4 On the General tab, unselect the Status check box and click Apply to disable the WLAN.
    Step 5 Re-click the ID number of the WLAN.
    Step 6 On the General tab, choose the interface for which you configured a primary DHCP server to be used with this WLAN from the Interface drop-down list.
    Step 7 Choose the Advanced tab to open the WLANs > Edit (Advanced) page.
    Step 8 If you want to define a DHCP server on the WLAN that will override the DHCP server address on the interface assigned to the WLAN, select the DHCP Server Override check box and enter the IP address of the desired DHCP server in the DHCP Server IP Addr text box. The default value for the check box is disabled.
    Note The preferred method for configuring DHCP is to use the primary DHCP address assigned to a particular interface instead of the DHCP server override.
    Note DHCP Server override is applicable only for the default group.
    Step 9 If you want to require all clients to obtain their IP addresses from a DHCP server, select the DHCP Addr. Assignment Required check box. When this feature is enabled, any client with a static IP address is not allowed on the network. The default value is disabled.
    Note DHCP Addr. Assignment Required is not supported for wired guest LANs.
    Step 10 Click Apply to commit your changes.
    Step 11 On the General tab, select the Status check box and click Apply to reenable the WLAN.
    Step 12 Click Save Configuration to save your changes.
    Using the CLI to Configure DHCP
    To configure DHCP using the CLI, follow these steps:
    Step 1 Follow the instructions in the "Using the GUI to Configure the Management, AP-Manager, Virtual, and Service-Port Interfaces" section or "Using the GUI to Configure Dynamic Interfaces" section to configure a primary DHCP server for a management, AP-manager, or dynamic interface that will be assigned to the WLAN.
    Step 2 Disable the WLAN by entering this command:
    config wlan disable wlan_id
    Step 3 Specify the interface for which you configured a primary DHCP server to be used with this WLAN by entering this command:
    config wlan interface wlan_id interface_name
    Step 4 If you want to define a DHCP server on the WLAN that will override the DHCP server address on the interface assigned to the WLAN, enter this command:
    config wlan dhcp_server wlan_id dhcp_server_ip_address
    Note The preferred method for configuring DHCP is to use the primary DHCP address assigned to a particular interface instead of the DHCP server override. If you enable the override, you can use the show wlan command to verify that the DHCP server has been assigned to the WLAN.
    Step 5 Reenable the WLAN by entering this command:
    config wlan enable wlan_id

  • AIR-CT2504-50-K9 with out DHCP Static config

    We have AIR-CT2504-50-K9 and AIR-CAP1602I-TK910 30 devices we want config trough controller to AP with out DHCP

    #Yes, you can use internal dhcp server on WLC-2500 to lease IPs to the connected APs using L2/Broadcast, once AP gets an ip then you can make those IPs as static on those APs via check box from AP's general tab after it joins the WLC.
    #Remeber, WLC dhcp doesn't support option 43, if the AP and WLC management are L3, be sure to use ip-helper at L3 for wlc discovery. Also, don't think AP may receive ip from WLC dhcp server when it is L3 and dhcp proxy is used instead of broadcast.

  • Making Switch as DHCP server

    We have cisco 2950 switch. can we use it as dhcp server in our network if yes then how ?
    Please give me all commands to make it DHCP server.

    Hi Blue,
    i completely i won't accept the rest of ppl. say that DHCP is not supported on Cisco 2950, infact i am running dhcp server on my cisco 2950T-24 for the past 10 months IOS ver 12.1-22.EA6
    find the commands
    ip dhcp excluded-address 10.1.1.51 10.1.1.60
    ip dhcp pool xyz
    network 10.1.1.0 255.255.255.0
    domain-name abc.org
    dns-server 10.2.1.31
    default-router 10.1.1.252
    ip dhcp-server 10.1.1.250
    hope this helps.
    rate this post if cleared.

  • DHCP exclude address range option config on Instant 2.0

    Q:  DHCP exclude address range option config on Instant 2.0
    A: ​This article applies to Instant 4.2 and above.
    Before 4.2, Use exclude-address as a range option was not available.
    Since IAP is getting used as an Edge device, the features needs to be in compliance with industry standard. 
    From 4.2 onwards, IAP local DHCP server will support exclude IP address as a range.
    With this feature we are supporting the following
    A. exclude-address ip1
    B. exclude-address ip1 ip2
    Show dhcps command will show the excluded range and available range

    I found this on TCPIPGUIDE.com that supports my findings.
    "One difference between BOOTP and DHCP is that certain communications from the client to the server are unicast. The most noticeable instance of this is when a client tries to renew its lease with a specific DHCP server. Since it sends this request unicast, it can go to a DHCP server on a different network using conventional IP routing, and the relay agent does not need to be involved."

  • OS X Mountain Lion server spontaneous DHCP?

    I have DHCP service provided to a small school network by an Xserve running 10.6.8 server, not the new Mac mini server running 10.8.2, because the service is much more configurable in the old version (likely known to anyone perusing this forum). But we started having printing issues, and it turns out that the Mac mini started giving out IP addresses recently, despite the service being "off." Since it didn't have the reservations set, it gave some printers the wrong IP. I never turned the service on, but I wonder if the 10.8.2 update adding it to the Server app actually turns it on.
    The Console log shows lots of DHCP Offers and acks, it should show none. Under Server.app Services, "Your Mac now provides these services: File Sharing, Software Update, Netinstall (which services the iMac lab). Under DHCP, the service is off, but it shows clients to which it leased an address.
    I restricted the pool down to two addresses to reduce the possible problems, but I want to know a long-term fix. Something is horked.

    I should clarify my thoughts
    Have you noticed the progressive dumbing down and removal of services with osx server since snow leopard
    If you read the kb for mountain lion server you'll see that netinstall can use the dhcp service independently
    At one stage there was no GUI for dhcp at all and upgrading lion to mountain lion preserved dhcp setting
    http://support.apple.com/kb/HT5412
    Additional Information
    The bootpd process, which is used by the DHCP service, is also used by the NetInstall service, but you can use either service independently or both together.
    I have heard of cases of the bootpd.plist having no dhcp entries
    Try running
    sudo serveradmin fullstatus netboot
    And have a look at dhcp

  • What are DHCP settings and what is a DHCP lease

    My macbook has decided to stop logging on to my wifi router automatically.
    Seems the DHCP settings are wrong with an inappropriate IP address and Submask coded applied.
    When I change them back manually to what they were the computer says it is logged on to internet but refuses to open any internet application?
    I have tried the DHCP lease renewal prompt but still will not award appropriate IP or Submask code

    Hi RobertaMcC,
    Are you having trouble with a Wi-Fi connection or a wired (Ethernet) connection to the internet?  DHCP is a communications protocol that assigns each computer a unique IP address on the internet.    I'll include the information you specifically requested first, and general troubleshooting steps as well.
    OS X Yosemite: Renew an IP address from the DHCP server
    https://support.apple.com/kb/PH18513?locale=en_US
    Here is an overview of the troubleshooting steps for a Wi-Fi connection:
    Wi-Fi: How to troubleshoot Wi-Fi connectivity - Apple Support
    https://support.apple.com/en-ca/HT202222
    Hope that helps ...
    - Judy

  • DHCP Vmware fusion issue

    I have some clients connected to our cisco Wireless LAN controller (4402) and they are running vmware fusion 2. When connected to the wireless network their host machines do not aquire a IP when using DHCP. If you type in the IP manually it all works. If they connect by wire it works fine. If i put the host in NAT mode it works but i want it to work in bridge mode.

    We did that as well. Here is what I found out from an internal Cisco resource.
    The WLC software does not support multiple DHCP client instances running on a wireless client. There is no workaround for this, as only wireless clients registered with WLC (not bringing WGB into the picture) will have a MSCB entry and be able to get an IP address.
    When a wireless client has a virtual machine running on it (e.g. in VMware, VirtualPC or Parallels), and when that virtual machine is running in bridged mode rather than in NAT ("shared networking") mode, then the WLC DHCP relay will drop the DHCP packets from the VM client, with a "dhcpProxy: Dropping packet (no mscb)" message.
    It does not appear that the WLC's DHCP proxy functionality supports multiple DHCP clients behind the wireless client.
    Workarounds:
    1. Configure the virtual machine software for NAT ("shared networking") mode, not bridged mode.
    2. If using 4.1 WLC software, configure the virtual machine to use static IP addressing, not DHCP.

  • OES dhcp

    Looking at replacing my main location dns (netware) servers w/ oes
    servers.
    Is it possible to have multiple oes servers doing dhcp for the same
    subnets, like for load balancing?
    I ask as currently I have two nw65sp8 servers running dns for our
    primary/email internal dns. One of these does dhcp for our main
    location here as well as quite a few remote subnets.
    Would it be possible to replace both of these servers & have both of
    them doing dhcp for the same subnets (for load balancing), or will that
    not work (or is impossible)?
    Stevo

    On 16/04/2012 21:02, Stevo wrote:
    > Looking at replacing my main location dns (netware) servers w/ oes
    > servers.
    >
    > Is it possible to have multiple oes servers doing dhcp for the same
    > subnets, like for load balancing?
    >
    > I ask as currently I have two nw65sp8 servers running dns for our
    > primary/email internal dns. One of these does dhcp for our main
    > location here as well as quite a few remote subnets.
    >
    > Would it be possible to replace both of these servers& have both of
    > them doing dhcp for the same subnets (for load balancing), or will that
    > not work (or is impossible)?
    DHCP in OES supports failover so you can have two servers handling DHCP
    requests for the same subnet. There are however a couple of things to note:
    1) failover is for dynamic assignments only - if you want to handle
    static assignments there is an unsupported kludge you can use (which
    allows more than 2 DHCP servers)
    2) failover is set per service so it will cover all subnets created
    under that service
    HTH.
    Simon
    Novell/SUSE/NetIQ Knowledge Partner
    Do you work with Novell technologies at a university, college or school?
    If so, your campus could benefit from joining the Novell Technology
    Transfer Partner (TTP) program. See novell.com/ttp for more details.

  • VLANs, IPs and DHCP

    This may be a silly question but here goes:
    I have to set up two VLANs that do not speak to each other but use one uplink to the internet. I know how to set up VLANs and I know how to set it up so that it does not talk to each other. However, I only have one DHCP server. Is there any way to make that server assign IP addresses to both VLANS (i.e. VLAN01 IP block 192.168.1.0 and VLAN02 IP block 192.168.2.0)?
    Thank you.

    Hello,
    there are several options available.
    First you can setup a trunk to the server, if the server NIC is capable of doing this.
    Second you could use two ethernet interfaces on the server and attach it into the two VLANs. In both cases configure a matching IP address in each VLAN on the server.
    Third you could use a router with an "ip helper-address " command on a VLAN subinterface to operate as DHCP proxy. In the latter case you should apply additional access-lists to prevent inter-VLAN traffic. The router could even be operated as DHCP server itself, in case this would be interesting to you.
    In any case you have to configure your DHCP server to support both address ranges.
    Hope this helps! Please rate all posts.
    Regards, Martin

  • DHCP FORCERENEW Message

    Hi, 
    Is DHCP FORCERENEW (RFC 3203 ) message supported on Windows 7/8 ?
    I have a requirement where I need the DHCP server to initiate force renewal of client IP address.
    Thanks,
    Mohit 

    Hi,
    Based on my research, the protocol implementation must implement DHCP-AUTH to support DHCP FORCERENEW message. However, DHCP-AUTH is not supported on Windows DHCP client and server. Hence it wont be possible for the Windows DHCP
    client to accept FORCERENEW messages.
    Instead, you can run "ipconfig/release" and "ipconfig/renew" on DHCP clients to renew IP addresses.
    Best regards,
    Susie

  • Netinstall DHCP Options for Windows DHCP server

    Hello,
    We want to use Netinstall for imaging our Mac's. I don't want to add another DHCP server to support the Netinstall options. Can I add the Netinstall DHCP boot options to my existing Windows DHCP server? If it's possible, could you let me know what they are?
    Thanks for any help.
    All the best.
    Kevin

    The NetBoot technology does not use the traditional method for discovering the TFTP and NFS servers (DHCP options), but instead uses BSDP (Boot Service Discovery Protocol). On Mac OS X Server, bootpd happens to handle both DHCP and BSDP, and is configured to provide one or both services as needed. Check out the man page for bootpd, which goes into great detail as to how NetBoot functions.
    The short version is that you don't have to make any modifications to your existing DHCP server (it just has to provide a host IP address to the client, optionally with a router IP and DNS IPs). You just need to enable NetBoot on a Mac OS X Server system sitting on the same subnet as your clients.
    Shiloh
    PowerMac G5   Mac OS X (10.4.7)  

Maybe you are looking for

  • Trouble with itunes and time machine

    i am having trouble with my iphone and thought it may have been itunes, so i went into time machine and tried to replace my current version of itunes with the last one. Everything went fine until i got right to the end of replacing it. it said i didn

  • Compilation problem in 11g environment

    Hello mates, we have migrated from oracle 10g to 11g recently. we have lot of pro*c and forms programs. so i need to check all these programs are running same as in 10g environment. for this i want to compile all the pro*c programs in unix environmen

  • Password protecting a webpage.

    I'd like to password protect one page on my website. How do I do that?

  • Hearing no sound from internal speakers

    Just recently installed updates and lost my sound. When i go to system preferences to sound and output tab all the options are grayed out and i cant turn mute button off. Any ideas?

  • Where to download the TutWD_Languages_Init.zip file?

    Hi admin and experts of Web Dynpro Application, I've read the tutorial about the Internationalization of Web Dynpro Projects. In this tutorial, it needs to download the TutWD_Languages_Init.zip template file in website sdn.sap.com. But all I found ab