Didadm: unable to determine hostname. error on Sun cluster 4.0 - Solaris11
Trying to install Sun Cluster 4.0 on Sun Solaris 11 (x86-64).
iscs sharedi Quorum Disk are available in /dev/rdsk/ .. ran
devfsadm
cldevice populate
But don't see DID devices getting populated in /dev/did.
Also when scdidadm -L is issued getting the following error. Has any seen the same error ??
- didadm: unable to determine hostname.
Found in cluster 3.2 there was a Bug 6380956: didadm should exit with error message if it cannot determine the hostname
The sun cluster command didadm, didadm -l in particular, requires the hostname to function correctly. It uses the standard C library function gethostname to achieve this.
Early in the cluster boot, prior to the service svc:/system/identity:node coming online, gethostname() returns an empty string. This breaks didadm.
Can anyone point me in the right direction to get past this issue with shared quorum disk DID.
Let's step back a bit. First, what hardware are you installing on? Is it a supported platform or is it some guest VM? (That might contribute to the problems).
Next, after you installed Solaris 11, did the system boot cleanly and all the services come up? (svcs -x). If it did boot cleanly, what did 'uname -n' return? Do commands like 'getent hosts <your_hostname>' work? If there are problems here, Solaris Cluster won't be able to get round them.
If the Solaris install was clean, what were the results of the above host name commands after OSC was installed? Do the hostnames still resolve? If not, you need to look at why that is happening first.
Regards,
Tim
---
Similar Messages
-
Wrong hostname setting after Sun Cluster failover
Hi Gurus,
our PI system has been setup to fail over in a sun cluster with a virtual hostname s280m (primary host s280 secondary host s281)
The basis team set up the system profiles to use the virtual hostname, and I did all the steps in SAP Note 1052984 "Process Integration 7.1 High Availability" (my PI is 7.11)
Now I believe to have substituted "s280m" in every spot where previously "s280" existed, but when I start the system on the DR box (s281), the java stack throws erros when starting. Both SCS01 and DVEBMGS00 work directories contain a file called dev_sldregs with the following error:
Mon Apr 04 11:55:22 2011 Parsing XML document.
Mon Apr 04 11:55:22 2011 Supplier Name: BCControlInstance
Mon Apr 04 11:55:22 2011 Supplier Version: 1.0
Mon Apr 04 11:55:22 2011 Supplier Vendor:
Mon Apr 04 11:55:22 2011 CIM Model Version: 1.5.29
Mon Apr 04 11:55:22 2011 Using destination file '/usr/sap/XP1/SYS/global/slddest.cfg'.
Mon Apr 04 11:55:22 2011 Use binary key file '/usr/sap/XP1/SYS/global/slddest.cfg.key' for data decryption
Mon Apr 04 11:55:22 2011 Use encryted destination file '/usr/sap/XP1/SYS/global/slddest.cfg' as data source
Mon Apr 04 11:55:22 2011 HTTP trace: false
Mon Apr 04 11:55:22 2011 Data trace: false
Mon Apr 04 11:55:22 2011 Using destination file '/usr/sap/XP1/SYS/global/slddest.cfg'.
Mon Apr 04 11:55:22 2011 Use binary key file '/usr/sap/XP1/SYS/global/slddest.cfg.key' for data decryption
Mon Apr 04 11:55:22 2011 Use encryted destination file '/usr/sap/XP1/SYS/global/slddest.cfg' as data source
Mon Apr 04 11:55:22 2011 ******************************
Mon Apr 04 11:55:22 2011 *** Start SLD Registration ***
Mon Apr 04 11:55:22 2011 ******************************
Mon Apr 04 11:55:22 2011 HTTP open timeout = 420 sec
Mon Apr 04 11:55:22 2011 HTTP send timeout = 420 sec
Mon Apr 04 11:55:22 2011 HTTP response timeout = 420 sec
Mon Apr 04 11:55:22 2011 Used URL: http://s280:50000/sld/ds
Mon Apr 04 11:55:22 2011 HTTP open status: false - NI RC=0
Mon Apr 04 11:55:22 2011 Failed to open HTTP connection!
Mon Apr 04 11:55:22 2011 ****************************
Mon Apr 04 11:55:22 2011 *** End SLD Registration ***
Mon Apr 04 11:55:22 2011 ****************************
notice it is using the wrong hostname (s280 instead of s280m). Where did I forget to change the hostname? Any ideas?
thanks in advance,
PeterPlease note that the PI system is transparent about the Failover system used.
When you configure the parameters against the mentioned note, this means that in case one of the nodes is down, the load will be sent to another system under the same Web Dispatcher/Load Balancer.
When using the Solaris failover solution, it covers the whole environment, including the web dispatcher, database and all nodes.
Therefore, please check the configuration as per the page below, which talks specifically about the Solaris failover solution for SAP usage:
http://wikis.sun.com/display/SunCluster/InstallingandConfiguringSunClusterHAfor+SAP -
Failed to create resource - Error in Sun cluster 3.2
Hi All,
I have a 2 node cluster in place. When i trying to create a resource, i am getting following error.
Can anybody tell me why i am getting this. I have Sun Cluster 3.2 on Solaris 10.
I have created zpool called testpool.
clrs create -g test-rg -t SUNW.HAStoragePlus -p Zpools=testpool hasp-testpool-res
clrs: sun011:test011z - : no error
clrs: (C189917) VALIDATE on resource hasp-testpool-res, resource group test-rg, exited with non-zero exit status.
clrs: (C720144) Validation of resource hasp-testpool-res in resource group test-rg on node sun011:test011z failed.
clrs: (C891200) Failed to create resource "hasp-testpool-res".
Regards
KumarThorsten,
testpool created in one of the cluster nodes and is accessible from both the nodes in the cluster. But if it is imported in one node and will not be access from other node. If other node want to get access we need to export and import testpool in other node.
Storage LUNs allocated to testpool are accessible from all the nodes in the cluster and able import and export testpool from all the nodes in the cluster.
Regards
Kumar -
Cluster Transport Adapter Error - Sun Cluster
I am installing sun cluster 3.0 and it gives me an error saying:
failed to add cluster transport adapter - unknown adapter of transport type, trtype=dlpi...
My network card is syskonnect - interface is skge0.....
What is wrong....ThanksHi,
I have a similar problem .
Get the same error with Sun Cluster 3.0 the card is Phobos quad port.
Could find a solution to it or had to shell out a few hundred bucks for sun cards ? -
:: Running Hook [udev]
:: Triggering uevents...done
Root device '804' doesn't exist.
Creating root device /dev/root with major 8 and minor 4.
error: /dev/root: No such device or address
ERROR: Unable to determine the file system type of /dev/root:
Either it contains no filesystem, an unknown filesystem,
or more than one valid file system signature was found.
Try adding
rootfstype=your_filesystem_type
to the kernelcommand line.
You are now being dropped into an emergency shell.
/bin/sh: can't access tty; job control turned off
[ramfs /]# [ 1.376738] Refined TSC clocksource calibration: 3013.000 MHz.
[ 1.376775] Switching to clocksource tsc
That's what I get when I boot my Arch system. It worked fine for quite a while, but suddenly it ran into an error where the SCSI driver module was corrupt. I fixed it by reinstalling util-linux-ng and kernel26, however, I run into this issue now. http://www.pastie.org/2163181 < Link to /var/log/pacman.log for the month of July, just in case. Yes, I bought a new ATI/AMD Radeon HD 5450 this Saturday, but it seemed to work fine till this broke and it works fine on Ubuntu too, so I suppose we can rule it out.
Last edited by SgrA (2011-07-05 20:45:36)Autodetection failed on your first image, in both your previous kernel installs:
[2011-07-04 16:14] find: `/sys/devices': No such file or directory
Which means that sysfs was not mounted. You should be able to boot from the fallback image, which does not use autodetect. Figure out why /sys isn't mounted, as well, and fix that.
This is also a somewhat crappy bug in mkinitcpio that lets you create an autodetect image that's useless. It'll be fixed in the next version of mkinitcpio that makes it to core.
Last edited by falconindy (2011-07-04 17:41:19) -
I am running Firefox 31.0 on Mac OS X 10.6.8. I have it set to automatically check for updates, but not to automatically install them. Lately, I keep getting the error message "Update Failed" & "Firefox is unable to determine if there is an update available". But when I check manually, I get the message "Firefox is up-to-date". Any ideas on why it can no longer determine its update status?
Sometimes, the situation with complicated programs is;
Updating is fine, but sometimes the coding goes Gaa-Gaa. if
its update on update on update''' . . . . . .'''
So, every once in a while, instead of doing an update,
download the full installer. This should clean out the Gaa-Gaa.
If not, save the installer somewhere, remove the old program,
then use the installer.
Happy Computing. -
Unable to determine the value of component ''! Workflow error, please help
Hi All:
I am getting the error "Unable to determine the value of component ''" and workflows are not getting processed. I found OSS notes 879100 related to this issue but I am new to workflow and not sure where to start from! Here is the notes description:
The workflow WS20500025 ('Service Connection Order Processing') encounters an error directly after being started. The following error messages are displayed in the workflow log:
SWP102: Error at start of an IF branch
WL821: Work item 000000100012: Object FLOWITEM method EXECUTE cannot be executed
SWF_RUN535: Error '9' when calling service 'SO_OBJECT_SEND'
SWF_RUN534: Problems occurred when generating a mail
WL863: Notification of completion cannot be generated
SWF_EXP_001073: Unable to determine the value of component 'QUOTATION'
SWF_EXP_001072: Error in the evaluation of expression '<???>' for item 1
SWF_RLS_001101: Operator 'GT': The value of the left operand cannot be determined
SWP085: Error when starting work item 000000100012
SWP010: Error when evaluating the IF condition for node 0000000075
Other terms
Service connection processing, service connection workflow
Reason and Prerequisites
This is due to a program error.
The checks in the workflow Basis have been made stricter. A query of the type 'Quotation.number > 0' now causes an error if the container element 'Quotation' is not set. This is always the case if the workflow is is running without quotation prcessing, for instance.
Solution
The error is corrected in the next Support Package.
If you want to implement the corrections manually in your system, change the condition in step 000075 of workflow WS20500025 as follows:
&IS-U: Kundenangebot& EX
and &IS-U: Kundenangebot.Verkaufsbeleg& > 0
Save and activate the workflow.
I am new to workflow and not sure where to start from! Could someone please help me with this? Rewards assured.
Thanks.
MithunANy ideas? Please help me if anyone knows the answer.
Thanks.
Mithun -
ISE BYOD Error: "We are unable to determine access privileges" on redirect
I am running ISE 1.1.1 and have gone through the design guide and setup the certificate based wireless authentication and device registration process using the ISE as a SCEP proxy for handing out certificates. On the device registration portal instead of showing the device MAC the policy services node MAC shows up and I get an error that says "We are unable to determine access privileges in order to access the network. Please contact your adiminstrator."
The an hour later I can connect just fine. The authentication logs on ISE are exactly the same in both cases. So it seems like a bug I opened a TAC case but am also posting here.I havent opened a TAC case and havent seen this issue since when i first set this up.
Can you go to your devices portal (https://ipofise:8443/mydevices) login using your credentials and see if the device is registered or the status is set to lost. I would suggest deleting if it is there and try going through the process again.
Thanks,
Tarik Admani
*Please rate helpful posts* -
Mass role Import in ERM "unable to determine matching org. level" Error
I am trying to upload the Derived Roles into the ERM. I have already uploaded all the Parents Roles. The volumes of the Derived Roles is huge in my SAP Backend system.
I am not able to understand what should be the content of Org File which we upload. Please correct if I am wrong
1>Example a role Z_TEST_D is derived from Z_TEST on the org levels EKGRP,KOART,GSBER,WERKS.
2>I have run Org Synchronization Job in the ERM
3>Downloaded Z_TEST (Parent Role) and uploaded it into ERM(It was easy because there was no org file)
4> Downloaded Z_TEST_D(Derived Role) through /VIRSA/RE_DNLDROLES Tcode in backend.
5>Downloaded the AGR_1252 information for this role which contained the Org levels and values
6>I put all those information into the Org File and then tried to upload it throws me the error Role Z_TEST_D : not imported; unable to determine matching org. level for WERKSin the system
So I again tried with the another method by changing the input sheet for the Org File
Z_TEST_D BUKRS 0* 9*
Z_TEST_D EKGRP *
Z_TEST_D KOART *
Z_TEST_D GSBER *
Z_TEST_D WERKS *
and tried to upload it again gave me the same error. I have checked the ERM all these Org Levels are fetched into the ERM. I am not sure if I am missing any basic things.
Current Support pack: SP10 Hot Fix 2.
Please share your experience and best practice to upload the roles,Hello Rahul,
I had that same problem with SP10 also. The way I resolved itand this sounds crazywas to move that WERKS line up one or two rows.
The problem I noticed was not with all derived roles, but when there was a problem, it was always the last line of the Org file for the role that was causing the problem. And the problem was not always WERKS either.
If the next time you run it, the error occurs on the "new" last line (e.g. GSBER), move that line up also. Eventually they all make it in. I have not seen this problem repeated in SP12. Don't delete the line, just shift the order within the number of rows the role has.
P.S. I have several hundred derived roles, about 10 - 15% had this import problem.
-Dylan -
Error: 1056550: Unable to resolve hostname
Hello Experts,
When trying to open the already existing partition definitions, the following error occurs
Error: 1056550: Unable to resolve hostname
Any suggestions would be of great help.
Regards,
SudhirThank you
-
ERROR: unable to determine license level
I have Tuxedo 7.1 for windows NT version, and put Lic.txt file in
%TUXDIR%\udataobj\
To make sure, I run License utility 7.1 too.
ERROR: unable to determine license level
do you know what's the problem?
thank,
Kyoungseop KoHi, thanks for the reply. I don't use testing. I had upgraded to kernel 2.6.38.3-1. That caused the problem, so I downgraded to the previous version, 2.6.38.2-1, andthings are OK now.
Edit: I did pacman -Syu on both systems and after upgrading pacman I let it upgrade the kernel and it seems OK now. I would like to know what happened if anyone can shed some light.
Last edited by oboedad55 (2011-04-21 02:32:47) -
Error:Unable to determine data basis for virtual InfoCube.
Hi all,
I am working on Virtual cubes. I have created a query on virtual cube which is getting loaded from a transaction cube. I am using a transaction cube which is a copy of standard cube <b>0BCS_C10 - Consolidation (Company/Profit Center).</b> (Transaction cube).
When I execute the query in BEX it is disconnecting from the server and if I execute the same in transaction <b>RSRT</b> it is showing following errors.
1.Unable to determine data basis for virtual InfoCube.
2.Error reading the data of InfoProvider.
3.System error in program SAPLRRK0 and form RSRDR;SRRK0F30-01-
Will be thankful for suggestions.Hi Pankesh,
Thanks for the response..
Transaction cube contains data and characteristics of virtual cube are consistent.
I am trying to see the contents of the virtual cube in transaction <b>LISTCUBE</b>, there also its showing same errors.
How can I proceed now? -
Error - unable to determine DB and SAP version
Hi!
Getting struct in prepare phase of solution manager 3.2 to 4 upgrade.
Getting error unable to determine the DB and SAP version.
during the prepare during the DBCHK
phase of solution manager getting the error " SEVERE ERROR: unable to
determine DB and SAP version."
The following files must be in the path described by
the environment variable "PATH":
icuuc30.dll, icudt30.dll, icuin30.dll [nlsui0.c 1489] pid = 2268
Kindly assistdear Elmar,
Hi!
The entries are not there in path, but R3trans -d IS SHOWING ONLY following-
C:\Documents and Settings\smpadm>r3trans.exe -d
This is r3trans.exe version 6.13 (release 640 - 26.02.07 - 15:37:00).
r3trans.exe finished (0000).
And Echo path is - E:\oracle\SMP\102\bin;C:\WINDOWS;C:\WINDOWS\System32;E:\usr\sap\SMP\SYS\exe\run
Kindly suggest
sanjay
Message was edited by:
Sanjay Birari -
How to fix error 35: Unable to determine UUID
I am having some issues with *long* boot times and Time machine errors on my iMac. I tried disk repair and hardware test, but they did not find anything. In fact, I have a bootcamp partition that is running fine, so it is unlikely to be a hardware issue.
The above is the only error I seem to see, could this be causing the problem? Is there a way to fix it?Sorry to take so long:
Hardware Overview:
Model Name: iMac
Model Identifier: iMac10,1
Processor Name: Intel Core 2 Duo
Processor Speed: 3.06 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 3 MB
Memory: 4 GB
Bus Speed: 1.07 GHz
Boot ROM Version: IM101.00CC.B00
SMC Version (system): 1.52f9
Serial Number (system): W8*****B9U
12/19/13 6:38:14 PM com.apple.launchd[1] (com.apple.xprotectupdater[33]) Exited with exit code: 252
12/19/13 6:38:17 PM configd[13] network configuration changed.
12/19/13 6:39:04 PM mdworker[91] _CFGetHostUUIDString: unable to determine UUID for host. Error: 35
12/19/13 6:39:05 PM configd[13] InterfaceNamer: timed out waiting for IOKit to quiesce
12/19/13 6:39:05 PM configd[13] InterfaceNamer: Busy services :
12/19/13 6:39:05 PM configd[13] InterfaceNamer: iMac10,1 [1]
12/19/13 6:39:05 PM configd[13] InterfaceNamer: iMac10,1/AppleACPIPlatformExpert [2]
12/19/13 6:39:05 PM configd[13] InterfaceNamer: iMac10,1/AppleACPIPlatformExpert/CPU1@1 [1]
12/19/13 6:39:05 PM configd[13] InterfaceNamer: iMac10,1/AppleACPIPlatformExpert/CPU1@1/AppleACPICPU [1]
12/19/13 6:39:05 PM configd[13] InterfaceNamer: iMac10,1/AppleACPIPlatformExpert/AppleEFIRuntime [1]
12/19/13 6:39:12 PM WindowServer[67] kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
12/19/13 6:39:12 PM com.apple.WindowServer[67] Thu Dec 19 18:39:12-XXXX-iMac.local WindowServer[67] <Error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged.
12/19/13 6:39:13 PM com.apple.SecurityServer[38] Session 0x1065521 created
12/19/13 6:39:13 PM com.apple.SecurityServer[38] Session 0x1065521 attributes 0x30
12/19/13 6:39:14 PM loginwindow[43] Login Window Started Security Agent
12/19/13 6:39:15 PM kernel NTFS driver 3.4 [Flags: R/W].
12/19/13 6:39:16 PM kernel NTFS volume name BOOTCAMP, version 3.1.
12/19/13 6:39:16 PM kernel NTFS-fs warning (device /dev/disk0s3, pid 114): ntfs_system_inodes_get(): $LogFile is not clean. Will not be able to remount read-write. Mount in Windows.
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 114): ntfs_next_security_id_init(): Index record with vcn 0xc is corrupt. $Secure is corrupt. Run chkdsk.
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 114): ntfs_secure_load(): Failed to determine next security_id (error 5).
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 114): ntfs_mount(): Failed to load system files (error 5).
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 114): ntfs_mount(): Mount failed (error 5).
12/19/13 6:39:16 PM kernel NTFS volume name BOOTCAMP, version 3.1.
12/19/13 6:39:16 PM kernel NTFS-fs warning (device /dev/disk0s3, pid 123): ntfs_system_inodes_get(): $LogFile is not clean. Will not be able to remount read-write. Mount in Windows.
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 123): ntfs_next_security_id_init(): Index record with vcn 0xc is corrupt. $Secure is corrupt. Run chkdsk.
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 123): ntfs_secure_load(): Failed to determine next security_id (error 5).
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 123): ntfs_mount(): Failed to load system files (error 5).
12/19/13 6:39:16 PM kernel NTFS-fs error (device /dev/disk0s3, pid 123): ntfs_mount(): Mount failed (error 5).
12/19/13 6:39:16 PM SecurityAgent[117] Showing Login Window
12/19/13 6:39:18 PM warmd[34] [fetcher_open_file:936] open("/var/db/dyld/dyld_shared_cache_x86_64") => -1 (errno: 2)
12/19/13 6:39:18 PM warmd[34] [fetcher_open_file:936] open("/var/db/dyld/dyld_shared_cache_i386") => -1 (errno: 2)
12/19/13 6:43:12 PM /usr/libexec/hidd[46] Timeout waiting for IOKit to be quiet
12/19/13 6:47:12 PM WindowServer[67] Timeout waiting for IOKit to be quiet
12/19/13 7:18:00 PM SecurityAgent[117] User info context values set for XXXx
12/19/13 7:18:00 PM authorizationhost[109] Failed to authenticate user <XXXXX> (tDirStatus: -14090).
12/19/13 7:18:05 PM SecurityAgent[117] User info context values set for XXXXXX
12/19/13 7:18:05 PM SecurityAgent[117] Login Window Showing Progress
12/19/13 7:18:05 PM SecurityAgent[117] Login Window done
12/19/13 7:18:05 PM loginwindow[43] Login Window - Returned from Security Agent
12/19/13 7:18:05 PM loginwindow[43] USER_PROCESS: 43 console
12/19/13 7:18:06 PM com.apple.launchd.peruser.501[168] (com.apple.ReportCrash) Falling back to default Mach exception handler. Could not find: com.apple.ReportCrash.Self
12/19/13 7:18:14 PM com.apple.launchd.peruser.501[168] (com.apple.Kerberos.renew.plist[186]) Exited with exit code: 1
12/19/13 7:18:14 PM com.apple.launchd.peruser.501[168] (com.apple.mrt.uiagent[185]) Exited with exit code: 255
12/19/13 7:18:17 PM com.apple.launchd.peruser.501[168] ([email protected][191]) Exited with exit code: 1
12/19/13 7:23:41 PM [0x0-0x16016].com.apple.SystemProfiler[225] nvram: nvram is not supported on this system
12/19/13 7:28:14 PM /System/Library/CoreServices/CCacheServer.app/Contents/MacOS/CCacheServer[196] No valid tickets, timing out
<Edited by Host> -
Unable to determine domain for account Uninstall ecc6 on domain
Hello All,
I am trying to uninstall sap ecc6 from a server on a domain . While proceeding with uninstallation, it got stuck with following error details after entering the database details on sapinst.exe
FSL-01018 Unable to determine domain for account S-1-5-21-705529515-409054649-1020538192-1108. The group name could not be found.
ERROR 2008-01-02 10:29:35
MUT-03025 Caught ESyException in Modulecall: ESAPinstException: error text undefined.
I am trying to uninstall by logging to that server as administrator of domain . Can you guys give me some clue to fix this.
Thank you in advanceHello All,
Here are the other log details
INFO 2008-01-29 11:02:05
An error occured and the user decided to retry the current step: "|NW_Uninstall|ind|ind|ind|ind|0|0|NW_System_Uninstall|ind|ind|ind|ind|3|0|NW_uninstallDB|ind|ind|ind|ind|1|0|NW_OraDBCheck|ind|ind|ind|ind|2|0|checkForExistingDatabase".
ERROR 2008-01-29 11:02:10
FSL-01015 Unable to determine whether account TESTSAP\Administrator is member of account wicomp05\ORA_C30_DBA. The group name could not be found.
ERROR 2008-01-29 11:02:10
MUT-03025 Caught ESyException in Modulecall: ESAPinstException: error text undefined.
ERROR 2008-01-29 11:02:10
FCO-00011 The step checkForExistingDatabase with step key |NW_Uninstall|ind|ind|ind|ind|0|0|NW_System_Uninstall|ind|ind|ind|ind|3|0|NW_uninstallDB|ind|ind|ind|ind|1|0|NW_OraDBCheck|ind|ind|ind|ind|2|0|checkForExistingDatabase was executed with status ERROR .
INFO 2008-01-29 11:02:17
An error occured and the user decided to retry the current step: "|NW_Uninstall|ind|ind|ind|ind|0|0|NW_System_Uninstall|ind|ind|ind|ind|3|0|NW_uninstallDB|ind|ind|ind|ind|1|0|NW_OraDBCheck|ind|ind|ind|ind|2|0|checkForExistingDatabase".
ERROR 2008-01-29 11:02:21
Here TESTSAP\Administrator is the administrator of domain TESTSAP on which sap is installed and wicomp05\ORA_C30_DBA is hostname and oracle dbsid and the group dba,
When I check on the the group ORA_C30_DBA, TESTSAP\Administrator is the member of group
I tried to change the name of the group to
ORA_C30_DBA1 and it successfully passed the phase of error. However the drop database phase seems like disabled and it tells to manually drop the database.
Can I proceed with this method and finally drop the database manually ?. Have any one done like this.
Please help.
Maybe you are looking for
-
How Do I Watch Movies From IPOD Video On My TV?
I have some movies on my ipod & i wanna hook it up to my projector to watch on the screen. The Projector has the Audio/Video Plugs, so whats some ways i can do this and what will i need to buy? thx!
-
Is there a feature to load XML into Oracle 9 ?
Hello, I receive some XML files containing error messages from an external vendor, so i want to load these files into my database, yet i never worked with xml for import, so i dont really know if oracle has a build in feature like sqlldr, that i coul
-
How do i get my Itunes library from my crashed hard drive to put on my new computer? The old computer had Windows Vista and the new computer has Windows 8.
-
How can i read my wd passport usb 3 on my mac os lion 10.7.4??
When i connect the wd passport in mac , i see the disk enables but there isn't anywhere in the desktop.. i searched for some driver issues but i didn't understand why is that happend and especially no solution for this kind of problem.. Wonderlust Ki
-
Copy sapscript form to different language
Hi All, I'm trying to copy a form that was created in hebrew to the same form name but with language english. (the original language and the language key are the same now). I can't find a way to do this. Does any one have any idea ? Thanks, Michal.