DMVPN spoke to spoke not established

In the topology attached I am advertising tunnel ip and loopbacks for the specific hub and spokes in their eigrp , there is connectivity between all but still Eigrp routes are not coming and its flapping.ISAKMP is on , tunnel is also up.I am also attaching hub and spoke configs and topology  for your reference.
This is the error message:
7:09.791: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 145: Neighbor 172.16.145.5 (Tunnel0) is down: retry limit exceeded
*Mar  1 00:57:11.351: %CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec'd IPSEC packet has invalid spi for destaddr=10.1.12.1, prot=50, spi=0x77DF7896(2011134102), srcaddr        in use settings ={Transport, }
        conn id: 29, flow_id: SW:29, crypto map: Tunnel0-head-0
        sa timing: remaining key lifetime (k/sec): (4405256/3495)
        IV size: 8 bytes
        replay detection support: Y
        Status: ACTIVE
*Mar  1 00:57:21.895: YPTO-6-PRINTABORT: deletion caused early termination of show output for identity
R1#
*Mar  1 00:09:49.443: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 145: Neighbor 172.16.145.4 (Tunnel0) is down: retry limit exceeded
*Mar  1 00:09:50.051: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 145: Neighbor 172.16.145.4 (Tunnel0) is up: new adjacency
*Mar  1 00:11:00.311: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 145: Neighbor 172.16.145.5 (Tunnel0) is down: retry limit exceeded
*Mar  1 00:11:00.775: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 145: Neighbor 172.16.145.5 (Tunnel0) is up: new adjacency
*Mar  1 00:11:09.575: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 145: Neighbor 172.16.145.4 (Tunnel0) is down: retry limit exceeded
*Mar  1 00:11:11.551: %DUAL-5-NBRCHANGE: IP-EIGRP(0) 145: Neighbor 172.16.145.4 (Tunnel0) is up: new adjacency

For some reason, my spoke to spoke tunnel doesn't stay up when my hub goes down. Not sure what I am missing. Please help!!
Hub:
interface Tunnel0
 ip address 172.16.1.1 255.255.255.0
 no ip redirects
 no ip next-hop-self eigrp 10
 no ip split-horizon eigrp 10
 ip nhrp authentication _GW_
 ip nhrp map multicast dynamic
 ip nhrp network-id 1
 no ip split-horizon
 ip summary-address eigrp 10 10.1.0.0 255.255.0.0
 tunnel source 1.1.1.1
 tunnel mode gre multipoint
 tunnel protection ipsec profile dmvpn
end
spoke 1: 
interface Tunnel0
 ip address 172.16.1.7 255.255.255.0
 no ip redirects
 no ip split-horizon eigrp 10
 ip nhrp authentication _GW_
 ip nhrp map multicast dynamic
 ip nhrp map 172.16.1.1 1.1.1
 ip nhrp map multicast 1.1.1.1
 ip nhrp network-id 1
 ip nhrp nhs 172.16.1.1
 ip summary-address eigrp 10 10.7.0.0 255.255.0.0
 tunnel source GigabitEthernet0/0
 tunnel mode gre multipoint
 tunnel protection ipsec profile dmvpn
end
Spoke 2:
interface Tunnel0
 ip address 172.16.1.6 255.255.255.0
 no ip redirects
 no ip split-horizon eigrp 10
 ip nhrp authentication _GW_
 ip nhrp map multicast dynamic
 ip nhrp map 172.16.1.1 1.1.1.1
 ip nhrp map multicast 1.1.1.1
 ip nhrp network-id 1
 ip nhrp nhs 172.16.1.1
 ip summary-address eigrp 10 10.6.0.0 255.255.0.0
 tunnel source GigabitEthernet0/0
 tunnel mode gre multipoint
 tunnel protection ipsec profile dmvpn
end

Similar Messages

  • MPLS BGP routes push to DMVPN spokes

    I have an MPLS with BGP. I also have sites that are not connected directly to the MPLS, but have a s2s VPN to hub sites that are connected to the MPLS and that way they access the MPLS resources. I need to communicate the route changes to the MPLS when the DMVPN fails-over to another hub.
    Currently this is my config:
    Datacenter (MPLS only)
    interface GigabitEthernet0/1
    description MPLS
    ip address 192.168.0.34 255.255.255.252
    interface Vlan2
    ip address 192.168.96.2 255.255.255.0
    router bgp 65511
    bgp log-neighbor-changes
    network 192.168.96.0
    neighbor 192.168.0.33 remote-as 65510
    Hub site 1 (MPLS + internet)
    interface Tunnel200
    ip address 10.99.99.1 255.255.255.0
    no ip redirects
    ip mtu 1400
    ip nhrp authentication auth
    ip nhrp map multicast dynamic
    ip nhrp network-id 12345
    ip nhrp holdtime 600
    tunnel source GigabitEthernet0/0
    tunnel mode gre multipoint
    tunnel key 200
    tunnel protection ipsec profile dmvpn
    interface GigabitEthernet0/1
    description MPLS
    ip address 192.168.1.2 255.255.255.0 secondary
    ip address 192.168.0.2 255.255.255.252
    router bgp 65001
    bgp log-neighbor-changes
    network 192.168.1.0
    network 192.168.21.0
    !10.99 clients are DMVPN spokes
    neighbor 10.99.99.3 remote-as 99010
    neighbor 10.99.99.3 route-reflector-client
    neighbor 10.99.99.21 remote-as 99001
    neighbor 10.99.99.21 route-reflector-client
    !as 65000 is the MPLS PE
    neighbor 192.168.0.1 remote-as 65000
    Hub Site 2, has the same configuration, except for local ip address and router BGP ID.
    Spoke site:
    interface Tunnel200
    ip address 10.99.99.3 255.255.255.0
    no ip redirects
    ip mtu 1400
    ip nhrp authentication auth
    ip nhrp map 10.99.99.1 PUBLIC_IP_HUB_1
    ip nhrp map 10.99.99.16 PUBLIC_IP_HUB_2
    ip nhrp network-id 12345
    ip nhrp holdtime 600
    ip nhrp nhs 10.99.99.1 priority 1
    ip nhrp nhs 10.99.99.16 priority 5
    ip nhrp nhs fallback 60
    tunnel source GigabitEthernet0/0
    tunnel mode gre multipoint
    tunnel key 200
    tunnel protection ipsec profile dmvpn
    interface GigabitEthernet0/1
    description Internal
    ip address 192.168.3.1 255.255.255.192
    router bgp 99010
    bgp log-neighbor-changes
    network 192.168.3.0
    neighbor 10.99.99.1 remote-as 65001
    neighbor 10.99.99.16 remote-as 65013
    On this spoke site 
    #sh ip route
    B 192.168.1.0/24 [20/0] via 10.99.99.1, 00:47:01
    which is the HUB network, but the rest of the MPLS routes are not "learned".
    What am I missing?
    Thanks!

    Hi Jon, I've ommited the configuration of the MPLS provider routers in between.  The DC is connected to a router that has the AS 65510.
    DC:CPE---PE:{MPLS}PE---CPE:HUB---{internet}---Spoke
    The DC is ok getting the network information via BGP:
    #sh ip route
    B 192.168.3.0/24 [20/0] via 192.168.0.33, 3d05h
    B 192.168.21.0/24 [20/0] via 192.168.0.33, 3d05h
    #sh ip bgp 192.168.21.0
    BGP routing table entry for 192.168.21.0/24, version 559
    Paths: (1 available, best #1, table default)
    Not advertised to any peer
    Refresh Epoch 1
    65510 3549 6140 3549 65000
    192.168.0.33 from 192.168.0.33 (###.###.###.###)
    Origin IGP, localpref 100, valid, external, best
    #sh ip route 192.168.21.0
    Routing entry for 192.168.21.0/24
    Known via "bgp 65511", distance 20, metric 0
    Tag 65510, type external
    Last update from 192.168.0.33 3d05h ago
    Routing Descriptor Blocks:
    * 192.168.0.33, from 192.168.0.33, 3d05h ago
    Route metric is 0, traffic share count is 1
    AS Hops 5
    Route tag 65510
    MPLS label: none
    Spoke:
    #sh ip bgp
    BGP table version is 494, local router ID is 192.168.21.1
    Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
    r RIB-failure, S Stale, m multipath, b backup-path, f RT-Filter,
    x best-external, a additional-path, c RIB-compressed,
    Origin codes: i - IGP, e - EGP, ? - incomplete
    RPKI validation codes: V valid, I invalid, N Not found
    Network Next Hop Metric LocPrf Weight Path
    *> 10.0.129.32/27 10.99.99.16 0 65013 65012 3549 ?
    *> 192.168.96.0 10.99.99.16 0 65013 65012 3549 6745 65510 ?
    #sh ip route 192.168.96.0
    Routing entry for 192.168.96.0/24
    Known via "bgp 99001", distance 20, metric 0
    Tag 65013, type external
    Last update from 10.99.99.16 00:02:11 ago
    Routing Descriptor Blocks:
    * 10.99.99.16, from 10.99.99.16, 00:02:11 ago
    Route metric is 0, traffic share count is 1
    AS Hops 5
    Route tag 65013
    MPLS label: none
    #sh ip bgp 192.168.96.0
    BGP routing table entry for 192.168.96.0/24, version 465
    Paths: (1 available, best #1, table default)
    Not advertised to any peer
    Refresh Epoch 2
    65013 65012 3549 6745 65510
    10.99.99.16 from 10.99.99.16 (10.2.16.1)
    Origin incomplete, localpref 100, valid, external, best
    The route is not being updated to the rest of the routers, and the 192.168.21.0 network is still announced via the old route.
    (from spoke)
    ping 192.168.96.2
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 192.168.96.2, timeout is 2 seconds:
    Success rate is 0 percent (0/5)
    From DC
    #traceroute 192.168.21.1
    Type escape sequence to abort.
    Tracing the route to 192.168.21.1
    VRF info: (vrf in name/id, vrf out name/id)
    1 192.168.0.33 [AS 65510] 0 msec 0 msec 0 msec
    2 172.50.1.33 [AS 65510] 56 msec 36 msec 36 msec
    3 10.80.1.1 [AS 3549] 44 msec 44 msec 44 msec
    4 10.80.1.2 [AS 3549] 172 msec 172 msec 168 msec
    5 172.50.1.1 [AS 3549] 168 msec 168 msec 172 msec
    6 172.50.1.2 [AS 3549] 180 msec 180 msec 176 msec
    7 192.168.0.2 [AS 65000] 172 msec 172 msec 168 msec <- old route, should be 192.168.0.9
    8 192.168.0.2 [AS 65000] !H * !H

  • Distribute list on DMVPN spoke

    Hi,
    I would need to apply a distribute list on a DMVPN spoke and not sure if that DL needs to be applied at the tunnel interface or the physical interface where the tunnel is sourced. Please let me know if you have any thoughts.
    This is how the configuration looks at other branches that do not have DMVPN configured:
    access-list 1 deny   0.0.0.0
    access-list 1 permit any
    access-list 2 permit 0.0.0.0
    access-list 2 deny   any
    router eigrp 1
    distribute-list 2 in FastEthernet0/0
    distribute-list 1 out FastEthernet0/0
    Thanks,

    If you want to control your routing between the spoke and the hub, you have to apply it for the tunnel-interface. Or more general: With the interface that is enabled for the routing-protocol.
    And you should look at the prefix-lists instead of distribute-lists. They are much more flexible once you get used to them.
    http://www.cisco.com/en/US/partner/tech/tk365/technologies_q_and_a_item09186a008012dac4.shtml#fourteen
    Don't stop after you've improved your network! Improve the world by lending money to the working poor:
    http://www.kiva.org/invitedby/karsteni

  • VPN server on 871 already functioning as DMVPN spoke?

    Last week I was sitting in an hotel far away from my family. I wanted to use Skype or MSNMessenger to contact them with Webcam. It didn't work, because there was some huge firewall, blocking several ports. So I decided to setup a VPN server @home, so I could access to everything I wanted, and not be blocked by the firewall of an islamic state... :-)
    My 871w @home is functioning as a DMVPN spoke which works well.
    Is it possible to contact my router from far away, and then be able to access the internet and my home-lan?
    If someone can point me to a (simple :-) config, I will be very thankful...

    Try these links:
    http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a008014bcd7.shtml
    http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a00801eafcb.shtml
    http://www.cisco.com/en/US/products/ps6660/products_white_paper0900aecd803e7ee9.shtml

  • Coherence::net::messaging::ConnectionException: could not establish a connection to one of the following addresses: {10.242.152.242/10.242.152.242:8088}; make sure the "remote-addresses" configuration element contains an address and port of a running TcpA

    Hi
    I have installed coheI have installed coherence server "fmw_12.1.3.0.0_coherence_Disk1_1of1.zip" along with Examples on windows machine and C++ client coherence-cpp-12.1.3.0.0b51709-windows-x86-vs2012.zip on the same machine.
    I have built the "contacts" C++ Example successfully and while I execute this "contacts" using run I am facing TcpAcceptor error.
    On my coherence server the TcpAcceptor is listening on port 8088, so I have modified the extend-cache-config.xml file with values "ip address of my windows machine" and port as "8088".
    All the time I am getting below error,
    coherence::net::messaging::ConnectionException: could not establish a connection to one of the following addresses: {10.242.152.242/10.242.152.242:8088}; make sure the "remote-addresses" configuration element contains an address and port of a running TcpAcceptor
        at class coherence::lang::TypedHandle<class coherence::component::net::extend::PofConnection> __thiscall coherence::component::util::TcpInitiator::openConne
    ction(void)(TcpInitiator.cpp:307)
        at coherence::component::util::TcpInitiator::openConnection
        at coherence::component::util::Initiator::ensureConnection
        at coherence::component::net::extend::RemoteCacheService::openChannel
        at coherence::component::net::extend::RemoteService::doStart
        at coherence::component::net::extend::RemoteService::start
        at coherence::component::util::SafeService::startService
        at coherence::component::util::SafeService::restartService
        at coherence::component::util::SafeService::ensureRunningServiceInternal
        at coherence::component::util::SafeService::start
        at coherence::net::DefaultConfigurableCacheFactory::configureService
        at coherence::net::DefaultConfigurableCacheFactory::ensureService
        at coherence::net::DefaultConfigurableCacheFactory::ensureRemoteCache
        at coherence::net::DefaultConfigurableCacheFactory::configureCache
        at coherence::net::DefaultConfigurableCacheFactory::ensureCache
        at coherence::net::CacheFactory::getCache
        at unsigned __int64 coherence::lang::class_spec<class coherence::lang::Managed<class ContactId>,class coherence::lang::extends<class coherence::lang::Object,class coherence::lang::Void<class coherence::lang::Object> >,class coherence::lang::implements<void,void,void,void,void,void,void,void,void,void,void,void,void,void,void,void> >::sizeOf(bool)
        at _onexit
        at class coherence::util::Hashtable * coherence::lang::factory<class coherence::util::Hashtable>::create(void)
        at class coherence::util::Hashtable * coherence::lang::factory<class coherence::util::Hashtable>::create(void)
        at BaseThreadInitThunk
        at RtlInitializeExceptionChain
        at RtlInitializeExceptionChain
        on thread "main"
    Caused by: coherence::net::messaging::ConnectionException: coherence::component::util::TcpInitiator::TcpConnection@029EAD78{Id=NULL, Open=1, LocalAddress=NULL,
    RemoteAddress=10.242.152.242/10.242.152.242:8088}: socket disconnect
        at class coherence::lang::TypedHandle<class coherence::net::messaging::Response> __thiscall coherence::component::net::extend::AbstractPofRequest::Status::g
    etResponse(void)(AbstractPofRequest.cpp:203)
        at coherence::component::net::extend::AbstractPofRequest::Status::getResponse
        at coherence::component::net::extend::AbstractPofRequest::Status::waitForResponse
        at coherence::component::util::Initiator::openConnection
        at coherence::component::net::extend::PofConnection::open
        at coherence::component::util::TcpInitiator::openConnection
        at coherence::component::util::Initiator::ensureConnection
        at coherence::component::net::extend::RemoteCacheService::openChannel
        at coherence::component::net::extend::RemoteService::doStart
        at coherence::component::net::extend::RemoteService::start
        at coherence::component::util::SafeService::startService
        at coherence::component::util::SafeService::restartService
        at coherence::component::util::SafeService::ensureRunningServiceInternal
        at coherence::component::util::SafeService::start
        at coherence::net::DefaultConfigurableCacheFactory::configureService
        at coherence::net::DefaultConfigurableCacheFactory::ensureService
        at coherence::net::DefaultConfigurableCacheFactory::ensureRemoteCache
        at coherence::net::DefaultConfigurableCacheFactory::configureCache
        at coherence::net::DefaultConfigurableCacheFactory::ensureCache
        at coherence::net::CacheFactory::getCache
        at unsigned __int64 coherence::lang::class_spec<class coherence::lang::Managed<class ContactId>,class coherence::lang::extends<class coherence::lang::Object
    ,class coherence::lang::Void<class coherence::lang::Object> >,class coherence::lang::implements<void,void,void,void,void,void,void,void,void,void,void,void,void
    ,void,void,void> >::sizeOf(bool)
        at _onexit
        at class coherence::util::Hashtable * coherence::lang::factory<class coherence::util::Hashtable>::create(void)
        at class coherence::util::Hashtable * coherence::lang::factory<class coherence::util::Hashtable>::create(void)
        at BaseThreadInitThunk
        at RtlInitializeExceptionChain
        at RtlInitializeExceptionChain
        on thread "main"
    Caused by: coherence::io::IOException: socket disconnect
        at unsigned int __thiscall coherence::net::Socket::readInternal(unsigned char *,unsigned int)(Socket.cpp:333)
        at coherence::net::Socket::readInternal
        at coherence::net::Socket::SocketInput::read
        at coherence::io::BufferedInputStream::fillBuffer
        at coherence::io::BufferedInputStream::read
        at coherence::component::util::TcpInitiator::readMessageLength
        at coherence::component::util::TcpInitiator::TcpConnection::TcpReader::onNotify
        at coherence::component::util::Daemon::run
        at coherence::lang::Thread::run
        on thread "ExtendTcpCacheService:coherence::component::util::TcpInitiator:coherence::component::util::TcpInitiator::TcpConnection::TcpReader"

    We are facing same issue.    Could you please provide us any working .Net sample code for the version 12.1.2.0.
    <ssl>
                  <protocol>Tls</protocol>
                  <local-certificates>
                    <certificate>
                      <url>c:\Cert\</url>
                      <password>password</password>
                      <flags>DefaultKeySet</flags>
                    </certificate>
                  </local-certificates>
                </ssl>
    thanks
    Bala

  • TF215097: An error occurred while initializing a build for build definition : Could not establish trust relationship for the SSL/TLS secure channel

    Hello,
    We are facing an issue when triggering a new build using TFS 2013 Update 4, VS2013 Update 4 using TFVCTemplate.12.XAML template. All our other older build definitions just work fine but not the TFVCTemplate.12.XAML.  It seems to me that some certificate
    might be invalidated. Can anyone please point me in the right direction? 
    Thanks, 
    Mitul
    TF215097: An error occurred while initializing a build for build definition :
    Exception Message: One or more errors occurred. (type AggregateException)
    Exception Stack Trace: at System.Threading.Tasks.Task`1.GetResultCore(Boolean waitCompletionNotification)
    at Microsoft.TeamFoundation.Build.Client.FileContainerHelper.GetFile(TfsTeamProjectCollection projectCollection, String itemPath, Stream outputStream)
    at Microsoft.TeamFoundation.Build.Client.FileContainerHelper.GetFileAsString(TfsTeamProjectCollection projectCollection, String itemPath)
    at Microsoft.TeamFoundation.Build.Client.ProcessTemplate.Download(String sourceGetVersion)
    at Microsoft.TeamFoundation.Build.Hosting.BuildControllerWorkflowManager.PrepareRequestForBuild(WorkflowManagerActivity activity, IBuildDetail build, WorkflowRequest request, IDictionary`2 dataContext)
    at Microsoft.TeamFoundation.Build.Hosting.BuildWorkflowManager.TryStartWorkflow(WorkflowRequest request, WorkflowManagerActivity activity, BuildWorkflowInstance& workflowInstance, Exception& error, Boolean& syncLockTaken)
    Inner Exception Details:
    Exception Message: An error occurred while sending the request. (type HttpRequestException)
    Exception Stack Trace: at Microsoft.VisualStudio.Services.WebApi.VssHttpRetryMessageHandler.<SendAsync>d__1.MoveNext()
    --- End of stack trace from previous location where exception was thrown ---
    at System.Runtime.CompilerServices.TaskAwaiter.ThrowForNonSuccess(Task task)
    at System.Runtime.CompilerServices.TaskAwaiter.HandleNonSuccessAndDebuggerNotification(Task task)
    at System.Runtime.CompilerServices.ConfiguredTaskAwaitable`1.ConfiguredTaskAwaiter.GetResult()
    at Microsoft.VisualStudio.Services.WebApi.HttpClientExtensions.<DownloadFileFromTfsAsync>d__2.MoveNext()
    Inner Exception Details:
    Exception Message: The underlying connection was closed: Could not establish trust relationship for the SSL/TLS secure channel. (type WebException)Exception Stack Trace: at System.Net.HttpWebRequest.EndGetResponse(IAsyncResult asyncResult)
    at System.Net.Http.HttpClientHandler.GetResponseCallback(IAsyncResult ar)
    Inner Exception Details:
    Exception Message: The remote certificate is invalid according to the validation procedure. (type AuthenticationException)
    Exception Stack Trace: at System.Net.TlsStream.EndWrite(IAsyncResult asyncResult)
    at System.Net.ConnectStream.WriteHeadersCallback(IAsyncResult ar)

    Hi Mitul,
    Thanks for your reply.
    It’s strange, if your old build definitions can work using the same TFS Build Server, that indicate your TFS Server configuration is correct and can works. But only new build definition with default TfvcTemplate.12.xaml template cannot build successful.
    Please share your TFS Server detailed environment information here. And share your
    Build Service Properties dialog screenshot here.
    Try to clean the Cache for TFS 2013 manually(delete the content of the folder only, not the cache folder itself):
    Clean the Cache folder on Server machine. The folder path is:
    C:\Program Files\Microsoft Team Foundation Server 12.0\Application Tier\Web Services\_tfs_data.  
    After cleaned, on Server machine, click Start and select
    Run… to open the dialog box, then input iisreset.exe and click OK, wait it run completely.
    Additionally, you can run the TFS 2013 Power Tools BPA to scan the installation of your TFS Server.
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • Clean Access Server could not establish a secure connection

    I have a OOB Real IP GW setup on v4.1.2
    I seem to have a problem with the CAS connecting to the CAM although I have added the CAS to the CAM and can manage the CAS from the CAM.
    I noticed while troubleshooting client authentication that the client was not being redirected to the logon web page and it had full access to the trusted network from the untrusted authentication vlan. I eventually figured out that if I change the CAS Filter Fallback method from Allow to ignore then it tries to authenticate the client. However the fact that the fallback is activated tells you that something is not right.
    I have 2 problems:
    A) The clients web page is redirected for authentication but it only lists the domain name in the URL and not the hostname or host IP. In the lab I do not have a DNS server and it would not help as it does not include the hostname in the URL anyway. How do I fix this or perhaps it's related to the 2nd problem.
    B) When I manually change the URL by replacing the domain name with the IP of the CAS (untrusted OOB Real IP GW) then I get the following error message when logging on:
    Network Error:
    Clean Access Server could not establish a secure connection to Clean Access Manager at mydomain.com.
    This could be due to one or more of the following reasons: 1) Clean Access Manager certificate has expired 2) Clean Access Manager certificate cannot be trusted or 3) Clean Access Manager cannot be reached.
    Please report this to your network administrator.
    I would guess the culprit is No 2 but surely the system can run on self signed certificates? I have an NTP server so time is in sync. I have even tried regenerating the cetificates on the CAM
    & CAS.
    Any ideas?

    To overcome problem B, I regenerated the SSL Certificates using the host IP address instead of the name for all the CAM & CAS appliances. This seems to have resolved this problem.
    I also SSH'd from each of the CAS's to each of the CAM's from the CLI and it then prompts to permanently store the certificates. I'm not sure it this was necessary though.

  • WSUS Sync is not working Sync failed: UssCommunicationError: WebException: The underlying connection was closed: Could not establish trust relationship for the SSL/TLS secure channel. --- System.Security.Authentication.AuthenticationException: The remote

    I know there are loads of posts with same issue and most of them were related to proxy and connectivity .
    This was case for me as well (few months back). Now the same error is back. But I've confirmed that FW ports and proxy are fine this time around.
    server is configured on http port 80 
    ERROR
    Sync failed: UssCommunicationError: WebException: The underlying connection was closed: Could not establish trust relationship for the SSL/TLS secure channel. ---> System.Security.Authentication.AuthenticationException: The remote certificate is invalid
    according to the validation procedure.~~at System.Web.Services.Protocols.WebClientProtocol.GetWebResponse(WebRequest request). Source: Microsoft.SystemsManagementServer.SoftwareUpdatesManagement.WSyncAction.WSyncAction.SyncWSUS
    I've checked proxy server connectivity. I'm able browse following site from WSUS server
    http://catalog.update.microsoft.com/v7/site/Home.aspx?sku=wsus&version=3.2.7600.226&protocol=1.8
    I did telnet proxy server on the particular port (8080) and that is also fine.
    I've doubt on certificates, any idea which are the certificates which we need to look? And if certificate is expired then (my guess) we won't be able open the above mentioned windows update catalog site?
    Any tips appreciated !
    Anoop C Nair (My Blog www.AnoopCNair.com)
    - Twitter @anoopmannur -
    FaceBook Forum For SCCM

    Hi Lawrence ! - Many thanks for looking into this thread and replying. Appreciate your help.
    Your reply  ("SSL is enabled/configured, and the certificate being used is invalid
    (or the cert does not exist or cannot be obtained), or the SSL connection could not be established.") is very helpful.
    I've already tested CONTENT DOWNLOAD and it's working fine. WSUS Sync was also working fine for years with proxy server configured on port (8080) and WSUS server on port 80.
    My Guess (this is my best guess ;)) is this something to do with Firewall or Proxy side configuration rather than WSUS. However, I'm not finding a way to prove this to proxy/firewall team. From their perspective all the required port communication open and
    proxy server is also reachable. More over we're able to access internet (Microsoft Update Catalog site) over same port (8080).
    Any other hints where I can prove them it's a sure shot problem from their side.
    Thanks again !!
    Anoop C Nair (My Blog www.AnoopCNair.com)
    - Twitter @anoopmannur -
    FaceBook Forum For SCCM

  • I can not establish more then 1 call at the same time

    Hi,
    I have SPA9000 with four active accounts. I can not establish more then 1 call at the same time. Accounts are all in registered state. The field in SIP tab, Default Group Line:, is by default: 1,2,3,4 which means if line 1 is busy try the next one in the order ( in this case number 2). But this is not happening. It always tries to dial out with the first line (account). There is no problem with the provider and I don't want to specify groups of userID's and to assign them special line for dialing out.( by the way in this way it is possible to establish more parallel calls, but then each user will always have to dial thru specific line only). Please help me to find out if the SPA is faulty or give me some workaround, so that when I try to make a call , if one line is busy to dial out thru the next available.
    P.S. I suspect that SPA9000 does not notice when the line is busy or not. Maybe there is some issue with the Control Timer Values (sec) on Regional tab.
    Thanks,

    no it can only be one person at a time

  • Office Web Apps 2013 + could not establish trust relationship

    We currently have a three tier SharePoint 2013 Farm:
    1. Web Front End Server (Server 2008 R2 Enterprise) - Servername: TEST2SP013.domain.dom
    2. Central Admin Server (Server 2008 R2 Enterprise) - Servername: TEST2SPCA013.domain.dom
    3. SQL Server (Server 2012 Datacenter) - Servername: TESTSQL012.domain.dom
    All Machines are in the same IP/Subnet.
    We are trying to setup a new server (Server 2012 R2 Datacenter) (Servername: TEST022.domain.dom) to run Office Web Apps 2013 in our TEST environment to test the system before rolling in production and have had issues throughout the entire process.
    The technet articles we have used are:
    http://technet.microsoft.com/en-us/library/jj219435.aspx
    http://technet.microsoft.com/en-us/library/ff431687.aspx
    http://technet.microsoft.com/en-us/library/jj219627.aspx
    We finally have what I thought was a correct setup but anytime we try to edit or view a word, excel, powerpoint document within SharePoint 2013, we receive "Sorry, there was a problem and we can't open this document. If this happens again, try opening
    the document in Microsoft Word."
    We found a few How-To Setup Office Web Apps sites where other people provided step-by step instructions:
    blogs.msdn.com/b/sowmyancs/archive/2012/10/29/install-configure-amp-monitor-office-web-apps-2013-for-sp-2013.aspx
    http://www.wictorwilen.se/office-web-apps-2013-securing-your-wac-farm
    http://blogs.technet.com/b/justin_gao/archive/2013/06/30/configuring-office-web-apps-server-communication-using-https.aspx
    We reviewed the ULS logs and found the following error:
    02/14/2014 13:38:40.24  w3wp.exe (0x1C04)                        0x1BB4 Office Web Apps              
     WAC Hosting Interaction        adhsk Unexpected WOPI CheckFile: Catch-All Failure [exception:Microsoft.Office.Web.Common.EnvironmentAdapters.UnexpectedErrorException: HttpRequest failed ---> Microsoft.Office.Web.Apps.Common.HttpRequestAsyncException:
    No Response in WebException ---> System.Net.WebException: The underlying connection was closed: Could not establish trust relationship for the SSL/TLS secure channel. ---> System.Security.Authentication.AuthenticationException: The remote certificate
    is invalid according to the validation procedure.     at System.Net.TlsStream.EndWrite(IAsyncResult asyncResult)     at System.Net.ConnectStream.WriteHeadersCallback(IAsyncResult ar)     --- End of
    inner exception stack trace ---     at System.Net.HttpWebRequest.EndGetResponse(IAsyncResult asyncResult)     at Microsoft.Office.Web.Apps.Common.Ht... 7bed0d51-511d-4541-a059-e2f72942e617
    None of the article provide specific step-by-step instructions with using HTTPS in a test environment specifically when it comes to Self-Signed Certs through Active Directory Certificate Services.
    We tried creating a Self-Signed Cert through IIS on the Office Web Apps Box which did not work.
    We tried creating a Cert through Active Directory Certificate Services which did not work.
    We tried adding the Cert through Central Admin > Security > Manage Trust which did not help.
    We verified "get-spwopizone" is set to internal-https
    We can access the Web Apps https://test022/hosting/discovery site and view the XML with no issue on any machine on our network.
    We added our domain to the list of approved domains that can use Office Web Apps as well as add "Domain Users" as the security group that can "EDIT" Office Documents through Office Web Apps. 
    After each step, we tried performing either a system reboot or IIS Reset on the Office Web Appcs and WFE box.
    My Question is how do we generate a certificate (either self-signed through IIS on the Office Web Apps Box or through AD) that will allow this application to work? I read that the Fully Qualified Domain Name needs to be in the SAN field of the Cert but when
    we request it, I have no way of entering this information. I tried following http://technet.microsoft.com/en-us/library/ff625722 to manually request a certificate with a Custom SAN but that did not work either.
    I am assuming the certificate issue is with the New Office Web Apps box. Is this correct?
    -Chris

    If internal cert then you will have to add certificate from OWA to tursted certificates in each sharepoint server plus add the certificate from central admin in Sharepoint through manage trust. Also you will need to install p7b file (file that contains
    path to root certificate to verify each intermediate certificate) for internal cert to each sharepoint server to not get certificate error.
    sachin

  • Reporting services with R2 on DPM2012 - Could not establish trust relationship for the SSL/TLS secure channel

    Hi everyone,
    A somewhat similar question has been asked before by others but none of the answers given has helped me.I am attempting a DPM 2012 installation, which is failing at the "deploying reports" stage.My analysis of logs seems to point me in the direction of an SSL
    error, which does not make sense since the configuration files say SSL is disabled (or at least, should be).
    Here are the symptoms:
    1.I am able to browse http://FQDN/Reports_MSDPM2012 folder from internet explorer
    2.I am also able to browse http://FQDN/ReportServer_MSDPM2012 from internet explorer
    3.The information given in the logs and relevant config files is shown below:
    <<RSREPORTSERVER.CONFIG>>
    <ConnectionType>Default</ConnectionType>
    <LogonUser></LogonUser>
    <LogonDomain></LogonDomain>
    <LogonCred></LogonCred>
    <InstanceId>MSRS10_50.MSDPM2012</InstanceId>
    <InstallationID>{d9b1c335-5842-4a81-9148-79184c38bf09}</InstallationID>
    <Add Key="SecureConnectionLevel" Value="0"/>
    <Add Key="CleanupCycleMinutes" Value="10"/>
    <Add Key="MaxActiveReqForOneUser" Value="20"/>
    <Add Key="DatabaseQueryTimeout" Value="120"/>
    <Add Key="RunningRequestsScavengerCycle" Value="60"/>
    <Add Key="RunningRequestsDbCycle" Value="60"/>
    <Add Key="RunningRequestsAge" Value="30"/>
    <Add Key="MaxScheduleWait" Value="5"/>
    <Add Key="DisplayErrorLink" Value="true"/>
    <Add Key="WebServiceUseFileShareStorage" Value="false"/>
    <!--  <Add Key="ProcessTimeout" Value="150" /> -->
    <!--  <Add Key="ProcessTimeoutGcExtension" Value="30" /> -->
    <!--  <Add Key="WatsonFlags" Value="0x0430" /> full dump-->
    <!--  <Add Key="WatsonFlags" Value="0x0428" /> minidump -->
    <!--  <Add Key="WatsonFlags" Value="0x0002" /> no dump-->
    <Add Key="WatsonFlags" Value="0x0428"/>
    <Add Key="WatsonDumpOnExceptions" 
    4.The DPM log file still appears to be using SSL even though i used reporting services configuration to remove SSL bindings:
    running.Microsoft.Internal.EnterpriseStorage.Dls.Setup.Exceptions.BackEndErrorException: exception ---> Microsoft.Internal.EnterpriseStorage.Dls.Setup.Exceptions.ReportDeploymentException:
    exception ---> System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.Net.WebException: The underlying connection was closed: Could
    not establish trust relationship for the SSL/TLS secure channel. ---> System.Security.Authentication.AuthenticationException:
    The remote certificate is invalid according to the validation procedure.
       at System.Net.Security.SslState.StartSendAuthResetSignal(ProtocolToken message, AsyncProtocolRequest asyncRequest,
    Exception exception)
    5:I do have an SCCM site on the default web site used by SMS clients but on different ports
    I am stumped.Somebody please give some advice
    Thank you

    Hi
    This is an old post but did you come right?

  • The Network Adapter could not establish the connection;

    Hi
    I am using Oracle 9i JDeveloper Version 9.0.3.5.
    While running tutorial i am facing following error:
    Exception Details.
    oracle.apps.fnd.framework.OAException: Application: FND, Message Name: SYSTEM-ERROR. Tokens: MESSAGE = Io exception: The Network Adapter could not establish the connection; (Could not lookup message because there is no database connection)
         at oracle.apps.fnd.framework.server.OAExceptionUtils.processAOLJErrorStack(OAExceptionUtils.java:988)
         at oracle.apps.fnd.framework.server.OAUtility.getWebAppsContext(OAUtility.java:352)
         at oracle.apps.fnd.framework.CreateIcxSession.getEncryptedSessId(CreateIcxSession.java:144)
         at oracle.apps.fnd.framework.CreateIcxSession.createSession(CreateIcxSession.java:80)
         at test_fwktutorial._jspService(test_fwktutorial.jsp:45)
         at oracle.jsp.runtime.HttpJsp.service(HttpJsp.java:139)
         at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:317)
         at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:465)
         at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:379)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:727)
         at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:306)
         at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:767)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:259)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:106)
         at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:803)
         at java.lang.Thread.run(Thread.java:534)
    ## Detail 0 ##
    oracle.apps.fnd.framework.OAException: Application: FND, Message Name: FND_GENERIC_MESSAGE. Tokens: MESSAGE = java.sql.SQLException: Io exception: The Network Adapter could not establish the connection; (Could not lookup message because there is no database connection)
         at oracle.apps.fnd.framework.OAException.wrapperException(OAException.java:888)
         at oracle.apps.fnd.framework.OAException.wrapperException(OAException.java:862)
         at oracle.apps.fnd.framework.server.OAExceptionUtils.processAOLJErrorStack(OAExceptionUtils.java:980)
         at oracle.apps.fnd.framework.server.OAUtility.getWebAppsContext(OAUtility.java:352)
         at oracle.apps.fnd.framework.CreateIcxSession.getEncryptedSessId(CreateIcxSession.java:144)
         at oracle.apps.fnd.framework.CreateIcxSession.createSession(CreateIcxSession.java:80)
         at test_fwktutorial._jspService(test_fwktutorial.jsp:45)
         at oracle.jsp.runtime.HttpJsp.service(HttpJsp.java:139)
         at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:317)
         at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:465)
         at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:379)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:727)
         at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:306)
         at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:767)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:259)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:106)
         at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:803)
         at java.lang.Thread.run(Thread.java:534)
    ## Detail 0 ##
    java.sql.SQLException: Io exception: The Network Adapter could not establish the connection
         at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:134)
         at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:179)
         at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:334)
         at oracle.jdbc.ttc7.TTC7Protocol.handleIOException(TTC7Protocol.java:3675)
         at oracle.jdbc.ttc7.TTC7Protocol.logon(TTC7Protocol.java:352)
         at oracle.jdbc.driver.OracleConnection.<init>(OracleConnection.java:365)
         at oracle.jdbc.driver.OracleDriver.getConnectionInstance(OracleDriver.java:536)
         at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:328)
         at java.sql.DriverManager.getConnection(DriverManager.java:512)
         at java.sql.DriverManager.getConnection(DriverManager.java:140)
         at oracle.apps.fnd.security.ConnectionManager.dbConnect(ConnectionManager.java:1194)
         at oracle.apps.fnd.security.ConnectionManager.dbConnect(ConnectionManager.java:1121)
         at oracle.apps.fnd.security.AppsConnectionManager.makeGwyuidConn(AppsConnectionManager.java:664)
         at oracle.apps.fnd.security.AppsConnectionManager.getGwyuidConn(AppsConnectionManager.java:736)
         at oracle.apps.fnd.security.AppsConnectionManager.makeGuestConnection(AppsConnectionManager.java:575)
         at oracle.apps.fnd.security.DBConnObj.<init>(DBConnObj.java:240)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
         at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
         at java.lang.reflect.Constructor.newInstance(Constructor.java:274)
         at oracle.apps.fnd.common.Pool.createObject(Pool.java:1187)
         at oracle.apps.fnd.common.Pool.borrowObject(Pool.java:946)
         at oracle.apps.fnd.security.DBConnObjPool.borrowObject(DBConnObjPool.java:703)
         at oracle.apps.fnd.security.AppsConnectionManager.borrowConnection(AppsConnectionManager.java:232)
         at oracle.apps.fnd.common.Context.borrowConnection(Context.java:1773)
         at oracle.apps.fnd.common.AppsContext.getPrivateConnectionFinal(AppsContext.java:2460)
         at oracle.apps.fnd.common.AppsContext.getPrivateConnection(AppsContext.java:2398)
         at oracle.apps.fnd.common.AppsContext.getJDBCConnection(AppsContext.java:2257)
         at oracle.apps.fnd.common.AppsContext.getJDBCConnection(AppsContext.java:2072)
         at oracle.apps.fnd.common.AppsContext.getJDBCConnection(AppsContext.java:1976)
         at oracle.apps.fnd.profiles.Profiles.getConnection(Profiles.java:2494)
         at oracle.apps.fnd.profiles.Profiles.getProfileOption(Profiles.java:1304)
         at oracle.apps.fnd.profiles.Profiles.getProfile(Profiles.java:384)
         at oracle.apps.fnd.profiles.ExtendedProfileStore.getSpecificProfileFromDB(ExtendedProfileStore.java:210)
         at oracle.apps.fnd.profiles.ExtendedProfileStore.getSpecificProfile(ExtendedProfileStore.java:169)
         at oracle.apps.fnd.profiles.ExtendedProfileStore.getProfile(ExtendedProfileStore.java:148)
         at oracle.apps.fnd.common.logging.DebugEventManager.configureUsingDatabaseValues(DebugEventManager.java:1147)
         at oracle.apps.fnd.common.logging.DebugEventManager.configureLogging(DebugEventManager.java:1008)
         at oracle.apps.fnd.common.logging.DebugEventManager.internalReinit(DebugEventManager.java:977)
         at oracle.apps.fnd.common.logging.DebugEventManager.reInitialize(DebugEventManager.java:944)
         at oracle.apps.fnd.common.logging.DebugEventManager.reInitialize(DebugEventManager.java:931)
         at oracle.apps.fnd.common.AppsLog.reInitialize(AppsLog.java:570)
         at oracle.apps.fnd.common.AppsContext.initLog(AppsContext.java:873)
         at oracle.apps.fnd.common.AppsContext.initializeContext(AppsContext.java:858)
         at oracle.apps.fnd.common.AppsContext.initializeContext(AppsContext.java:827)
         at oracle.apps.fnd.common.AppsContext.<init>(AppsContext.java:686)
         at oracle.apps.fnd.common.WebAppsContext.<init>(WebAppsContext.java:846)
         at oracle.apps.fnd.framework.server.OAUtility.getWebAppsContext(OAUtility.java:351)
         at oracle.apps.fnd.framework.CreateIcxSession.getEncryptedSessId(CreateIcxSession.java:144)
         at oracle.apps.fnd.framework.CreateIcxSession.createSession(CreateIcxSession.java:80)
         at test_fwktutorial._jspService(test_fwktutorial.jsp:45)
         at oracle.jsp.runtime.HttpJsp.service(HttpJsp.java:139)
         at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:317)
         at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:465)
         at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:379)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:727)
         at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:306)
         at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:767)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:259)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:106)
         at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:803)
         at java.lang.Thread.run(Thread.java:534)
    oracle.apps.fnd.framework.OAException: Application: FND, Message Name: FND_GENERIC_MESSAGE. Tokens: MESSAGE = java.sql.SQLException: Io exception: The Network Adapter could not establish the connection; (Could not lookup message because there is no database connection)
         at oracle.apps.fnd.framework.OAException.wrapperException(OAException.java:888)
         at oracle.apps.fnd.framework.OAException.wrapperException(OAException.java:862)
         at oracle.apps.fnd.framework.server.OAExceptionUtils.processAOLJErrorStack(OAExceptionUtils.java:980)
         at oracle.apps.fnd.framework.server.OAUtility.getWebAppsContext(OAUtility.java:352)
         at oracle.apps.fnd.framework.CreateIcxSession.getEncryptedSessId(CreateIcxSession.java:144)
         at oracle.apps.fnd.framework.CreateIcxSession.createSession(CreateIcxSession.java:80)
         at test_fwktutorial._jspService(test_fwktutorial.jsp:45)
         at oracle.jsp.runtime.HttpJsp.service(HttpJsp.java:139)
         at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:317)
         at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:465)
         at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:379)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:727)
         at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:306)
         at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:767)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:259)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:106)
         at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:803)
         at java.lang.Thread.run(Thread.java:534)
    ## Detail 0 ##
    java.sql.SQLException: Io exception: The Network Adapter could not establish the connection
         at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:134)
         at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:179)
         at oracle.jdbc.dbaccess.DBError.throwSqlException(DBError.java:334)
         at oracle.jdbc.ttc7.TTC7Protocol.handleIOException(TTC7Protocol.java:3675)
         at oracle.jdbc.ttc7.TTC7Protocol.logon(TTC7Protocol.java:352)
         at oracle.jdbc.driver.OracleConnection.<init>(OracleConnection.java:365)
         at oracle.jdbc.driver.OracleDriver.getConnectionInstance(OracleDriver.java:536)
         at oracle.jdbc.driver.OracleDriver.connect(OracleDriver.java:328)
         at java.sql.DriverManager.getConnection(DriverManager.java:512)
         at java.sql.DriverManager.getConnection(DriverManager.java:140)
         at oracle.apps.fnd.security.ConnectionManager.dbConnect(ConnectionManager.java:1194)
         at oracle.apps.fnd.security.ConnectionManager.dbConnect(ConnectionManager.java:1121)
         at oracle.apps.fnd.security.AppsConnectionManager.makeGwyuidConn(AppsConnectionManager.java:664)
         at oracle.apps.fnd.security.AppsConnectionManager.getGwyuidConn(AppsConnectionManager.java:736)
         at oracle.apps.fnd.security.AppsConnectionManager.makeGuestConnection(AppsConnectionManager.java:575)
         at oracle.apps.fnd.security.DBConnObj.<init>(DBConnObj.java:240)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method)
         at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:39)
         at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:27)
         at java.lang.reflect.Constructor.newInstance(Constructor.java:274)
         at oracle.apps.fnd.common.Pool.createObject(Pool.java:1187)
         at oracle.apps.fnd.common.Pool.borrowObject(Pool.java:946)
         at oracle.apps.fnd.security.DBConnObjPool.borrowObject(DBConnObjPool.java:703)
         at oracle.apps.fnd.security.AppsConnectionManager.borrowConnection(AppsConnectionManager.java:232)
         at oracle.apps.fnd.common.Context.borrowConnection(Context.java:1773)
         at oracle.apps.fnd.common.AppsContext.getPrivateConnectionFinal(AppsContext.java:2460)
         at oracle.apps.fnd.common.AppsContext.getPrivateConnection(AppsContext.java:2398)
         at oracle.apps.fnd.common.AppsContext.getJDBCConnection(AppsContext.java:2257)
         at oracle.apps.fnd.common.AppsContext.getJDBCConnection(AppsContext.java:2072)
         at oracle.apps.fnd.common.AppsContext.getJDBCConnection(AppsContext.java:1976)
         at oracle.apps.fnd.profiles.Profiles.getConnection(Profiles.java:2494)
         at oracle.apps.fnd.profiles.Profiles.getProfileOption(Profiles.java:1304)
         at oracle.apps.fnd.profiles.Profiles.getProfile(Profiles.java:384)
         at oracle.apps.fnd.profiles.ExtendedProfileStore.getSpecificProfileFromDB(ExtendedProfileStore.java:210)
         at oracle.apps.fnd.profiles.ExtendedProfileStore.getSpecificProfile(ExtendedProfileStore.java:169)
         at oracle.apps.fnd.profiles.ExtendedProfileStore.getProfile(ExtendedProfileStore.java:148)
         at oracle.apps.fnd.common.logging.DebugEventManager.configureUsingDatabaseValues(DebugEventManager.java:1147)
         at oracle.apps.fnd.common.logging.DebugEventManager.configureLogging(DebugEventManager.java:1008)
         at oracle.apps.fnd.common.logging.DebugEventManager.internalReinit(DebugEventManager.java:977)
         at oracle.apps.fnd.common.logging.DebugEventManager.reInitialize(DebugEventManager.java:944)
         at oracle.apps.fnd.common.logging.DebugEventManager.reInitialize(DebugEventManager.java:931)
         at oracle.apps.fnd.common.AppsLog.reInitialize(AppsLog.java:570)
         at oracle.apps.fnd.common.AppsContext.initLog(AppsContext.java:873)
         at oracle.apps.fnd.common.AppsContext.initializeContext(AppsContext.java:858)
         at oracle.apps.fnd.common.AppsContext.initializeContext(AppsContext.java:827)
         at oracle.apps.fnd.common.AppsContext.<init>(AppsContext.java:686)
         at oracle.apps.fnd.common.WebAppsContext.<init>(WebAppsContext.java:846)
         at oracle.apps.fnd.framework.server.OAUtility.getWebAppsContext(OAUtility.java:351)
         at oracle.apps.fnd.framework.CreateIcxSession.getEncryptedSessId(CreateIcxSession.java:144)
         at oracle.apps.fnd.framework.CreateIcxSession.createSession(CreateIcxSession.java:80)
         at test_fwktutorial._jspService(test_fwktutorial.jsp:45)
         at oracle.jsp.runtime.HttpJsp.service(HttpJsp.java:139)
         at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:317)
         at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:465)
         at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:379)
         at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
         at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:727)
         at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:306)
         at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:767)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:259)
         at com.evermind.server.http.HttpRequestHandler.run(HttpRequestHandler.java:106)
         at EDU.oswego.cs.dl.util.concurrent.PooledExecutor$Worker.run(PooledExecutor.java:803)
         at java.lang.Thread.run(Thread.java:534)
    I have checked all the setups. Its as per document.
    I will appreciate any help on this.
    Thanks & Regards
    Samir

    Hi,
    according to the message, the database is not accessible. This can be because the database is down or the database connect information points e.g. to a wrong port
    Frank

  • Network adapter could not establish a connect from external server

    hi,
    I've set up a jdbc thin driver properly using
    the following input:
    "jdbc:oracle:thin:@ipaddress:1521:DBname",
    "username", "password"
    When outside users try to connect externally (outside the network) there is a different ipaddress. Although they are able to ping,
    telnet, run jsp etc... using the external address, they get the following error when they try the thin driver connection:
    i/o exception: network adapter could not establish a connection
    They change the ipaddress in the connection string to match the external ip. We are using oracle 8i, JRun on Linux. I have a feeling it has something to do with the tnsnames.ora file but I can't be sure.
    Any ideas?
    Thanks in advance!

    this is expected behavior ...
    the jdbc thin driver requires the use of an ip address that the calling program has acces to ...
    internally you have one ip address exposed.
    apparently you have another ip address set up for the external customer.
    fyi
    jdbc thin driver don'ts use the tnsnames.ora file -- they use "host:port:sid" because they are required to be platform independent and not access local datafiles or environment variables on the execution platform.
    jdbc oci drivers do use tnsnames.ora which provides the host:port:sid info in their entries.

  • HOW TO RESOLVE(Test failed: The Network Adapter could not establish the connection)

    Hii
    I want to create new databse as sysdba in jdev.I followed the steps as given in
    Oracle JDeveloper 11g Release 2 Tutorials - Designing and Building Database Tables
    In step 7 create database user and database connection, I am not able to do that and getting the error
    (Test failed: The Network Adapter could not establish the connection).
    Please help me.

    Hi,
    Could you please provide all value you pass to the connection properties on the connection creation panel? First of all, you should choose "Generic JDBC" as the connection type in order to use BDB SQL JDBC driver.
    Regards,
    Cindy

  • Status Failure -lo exception:network adapter could not establish connection

    Hi, installed SQL DEVELOPER today and its driving me mad... I am getting this error
    Status Failure -lo exception:network adapter could not establish connection.
    Basic tab I have all the right information, tried test gives same error...
    hostname ajas
    port 1521
    sid altaf
    TNS
    Network alias altaf
    connect identifier altaf(TRIED SINCE NETW ALIAS DIDNT WORK)
    went to TNS tab and from the list selected the right entry for NETWORK ALIAS,tried test still same error... tested with connect identifier still same error...went to Advanced entered this string jdbc:oracle:thin:@ajas:1521:altaf ..... still same error...what the hell is wrong...here is the tnsnames.ora entry ...
    ALTAF =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = AJAS)(PORT = 1521))
    (CONNECT_DATA =
    (SERVER = DEDICATED)
    (SERVICE_NAME = altaf)
    by the way I am able to connect with sql*plus ... lsnrctl gives the lsnr so thats running... tnslsnr is also running...also installed the latest java sdk i.e 1.5... i have set new path to point to this new java.exe i.e 1.5 one... this is really crazy and havent see such probs in any tools i have ever used and that too using it in normal pc ... God knows what will happen if used for remote db's....
    here is listener.ora
    LISTENER =
    (DESCRIPTION_LIST =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = AJAS)(PORT = 1521))
    SID_LIST_LISTENER =
    (SID_LIST =
    (SID_DESC =
    (SID_NAME = PLSExtProc)
    (ORACLE_HOME = C:\oracle\ora92)
    (PROGRAM = extproc)
    (SID_DESC =
    (GLOBAL_DBNAME = altaf)
    (ORACLE_HOME = C:\oracle\ora92)
    (SID_NAME = altaf)
    no one seems to have answer for this... there are all kinds of strange replies for this problem.... anyone has solved this prob plz reply....
    Message was edited by:
    ajashadi

    I've had the same problem when I installed the latest version of SQL developer (1.2.1.32.13) on a machine that still had an older, working version. My problem went away when I changed from an IP name to an IP address. on the connection setup window.

Maybe you are looking for

  • ERROR in COSTING VARIANCE and Picking the Halb Actual Cost in PrOr afterMRP

    Hi Gurus My PS collegue has a issue in Production order linking with his WBS element As it is a Production order related iam in the loop for resolving it Ok the Description of the Problem is "Error in Planned Variance Calculation of Production Order

  • Question/issue regarding querying for uncommited objects in Toplink...

    Hi, was hoping to get some insight into this problem we are encoutering… We have this scenario were we are creating a folder hierarchy (using Toplink) 1. a parent folder is created 2. child elements are created (in the same transaction as step 1), 3.

  • Bluetooth disappearing

    I know there are numerous posts on the solution to this issue. It ranges from resetting your firmware, to resetting your power management to rebooting and removing your battery for a few minutes. My own bluetooth unavailable issue is solved by merely

  • Actual layout of PDF output from printer is very small

    Hi there, I am currently sucessfully migrate Oracle reports from 6i to 10g (10,1,2) and the result looks fine from IE browser. When I try to print the report from printer, the image is occupied upper part of Letter size pager and it is very small whi

  • New imac, lightroom and cs3 can't read NEF files?  What to do

    Adobe support is down so I am here for help from all of you. I don't have a clue what bridge is or whether I need to use both bridge and Lightroom. Anyway, I will be importing nef files from a D300 to an external drive onsite with a windows xp pro la