Does the Modulation Toolkit support digitizers NI-PXI-5124 and NI-PCMCIA-5102?
I am using a demonstration NI-PXI unit to determine if it will support the application I am trying to develop. I need to demodulate a signal and determine the Quasi-peak value of the demodulated signal. The Modulation Toolkit states that it works with the 100MHz class of digitizers. Does it also support the 20 MHz and the 200 Mhz class of digitizers (NI-PXI-5124 and NI-PCMCIA-5102)?
Kent,
The Modulation Toolkit is fairly robust. I believe that it will work fine with the 20 and 200 MS/s boards. However, these obviously have to stay towards the lower frequency end of the spectrum. The Modulation Toolkit is most powerful with NI's RF products and is designed to do so. However, as I said, I believe that since the MT stays mostly on the software side and does not care too much about hardware it will not care about where the signals are coming from and will work for you.
Similar Messages
-
Need help with the Modulation Toolkit to configure a QPSK Modulation
Hi! I'm
trying to build a CDMA system with the Modulation Toolkit to use it later with
a PXI-RF Product as a part of my thesis (I don't remember the exact model
number because it's in my university and I'm home right now, sorry). But my problem right now is, I assume, a very simple one.
I'm having
some trouble understanding the MT Modulate PSK.vi and the MT
Demodulate PSK.vi since I have them both connected and the output bit stream is
not the same as the input bit stream. I'm guessing it's a problem with the sync
parameters in the MT Generate Synchronization Parameter.vi because maybe I
don't really understand how the sync bits work. I tried using a simple
sync header but the output bit stream is always shorter than the input and shows
only a little portion of the input bit stream and some of the 1's I used to
create the sync header, and it gets worse when I increase the number of input
bits.
I'm
attaching the simple vi I created to try to understand the mod-demod vi's, so
if someone knows what I'm doing wrong it would be great if you let me know
since I'm stuck in my thesis and understanding this issue will let me continue
with the project.
Thanks a
lot in advance!
Daniel
Attachments:
QPSK Test V-1.0.vi 31 KBPor favor mire en enlace abajo:
Cordiales Saludos
http://forums.ni.com/ni/board/message?board.id=6170&message.id=11549&jump=true
Luciano Borges
National Instruments Brazil
Luciano Borges
R&D Engineer
Pirelli Brazil -
Does the iPhone 5 support Sprint's 4G Wimaxx?
this is the answer i got from an Apple Support representative before he disappeared without saying anything:
Now Chatting with Kaeleb
Hi, welcome to the US Apple Online Store. How are you?
does the iphone 5 work on sprints 4g wimaxx and 4g lte?
Yes it sure does, the iPhone is designed to run Sprints network wherever you have it available.
i was told by a sprint representative that the iphone 5 is only capable of supporting their 3G or 4G LTE and doesn't supoort their 4G wimaxx
Then that information is correct
Our iPhone is designed to run whatever network the carrier allows for, if they have features not offered specifically they would be the ones with that information. The network information comes from the carrier.
yes but is the phone capable of it? it either has the antenna to connect to it or not
All iPhones have antennas to connect to a cellular network, the type of network it connects to is determined by the service provider, in your case Sprint.
I haven't heard from you for a few moments. Would you like to continue chatting?
your not giving me useful answers
I am giving you accurate information
Wether its useful or not, the information your looking for comes from Sprint.
there are specific antennas and frequencies that must be used depending on what you're trying to connect to
And since you have already discussed this with them, I have no idea why you are here asking us about something Sprint has already clarified for you.
your the company that designs and manufactures thephone
Your not getting it. As you said, we make the phone.
With an Antenna
The type of network* is determined by the service provider.
because prior to ever speaking with sprint one of your apple representatives gave me information contradicting that
4G, 4GLTE etc, all made up by the carriers to determine their networks.
what im asking is: is the iphone 5 made to be compatible with 4g wimaxx
whether or not sprint allows it to be
I get what your asking but your not quite understanding the answer. The iPhone is made compatible to connect to cellular network. Apple does not have information regarding which network types it will connect to, its designed to work on a GSM or CDMA network, the network strength which is 4G etc, is determined by the carrier. Here at Apple we have nothing to do with that.
We don't make iPhones designed specifically for 4G, 4G LTE, 4g wimaxx or any other network. Its made to run on a GSM or CDMA type network.
you manufacture 3 different iPhone that have specific antennas radio frquencies based on which carrier its going to be activated on
From the your carrier determines the compatibility.
Thats not true
We manufacture 2 types as I told you
GSM and CDMA
Sprint and Verizon are both CDMA
a verizon iphone cant be used on sprints network and vice versa because the use different frequencies
both cdma but different
like the differnence between wimaxx and lte
Not true, its because the phones are locked to the carriers services. It has nothing to do with Antennas, I am not sure where you are getting your information but if you can show me on our website where it says anything about 3 different Antennas then I would understand where you are coming from.
Let me get you the number to our technical support team so that we can find a resolution to this issue. 800-APL-CARE(800-275-2273)
one moment and i will
I am a sales chat and here to assist customers with the online store, I am not going to be able to leave this chat open for you to contact technical support.
i already spoke to them
Ok great, do you have any online sales questions I can answer for you?
they weren't able to give me an answer and aid to look online
I find that hard to believe, this team knows for a fact and are the experts they would never direct anyone to go online for that information. You may have spoke with customer service. You need to call technical support from the number I just have you.
well they did
GSM model A1428*: UMTS/HSPA+/DC-HSDPA (850, 900, 1700/2100, 1900, 2100 MHz); GSM/EDGE (850, 900, 1800, 1900 MHz); LTE (Bands 2, 4, 5, 17) CDMA model A1429*: CDMA EV-DO Rev. A and Rev. B (800, 1900, 2100 MHz); UMTS/HSPA+/DC-HSDPA (850, 900, 1900, 2100 MHz); GSM/EDGE (850, 900, 1800, 1900 MHz); LTE (Bands 1, 3, 5, 13, 25) GSM model A1429*: UMTS/HSPA+/DC-HSDPA (850, 900, 1900, 2100 MHz); GSM/EDGE (850, 900, 1800, 1900 MHz); LTE (Bands 1, 3, 5)
This is a final warning to stop this type of response. If this conversation is not kept on a professional level, this chat will end.
thats from your site
you asked me to show you thats what i did
You can call technical support but I need to assist customers with their purchases today.
i have been nothing but professional
i am a customer
i own a macbook air and mac mini
as well as 4th gen ipod touch and an old iphone 3gs
Great, this is a sales chat.
and this is how youre going to treat me?
I have helped you to the best of my ability, your in the wrong department
All I am doing is getting you to the correct team, because obviously you have not been given the information your looking for.
well you helped me as much as your so called technical support that youre trying to refer me to. even though i already stated they werent able to help me
I guarantee you didn't speak with the technical support team. There is no way they would send a customer online to seek that information, they are well aware that the online store chat is for online sales assistance. I am not going to continue to argue with you. This chat is not going anywhere with this back and forth. If you want assistance you will call our technical support team.
800-APL-CARE (800-275-2273)
thats who i spoke to at 10:03
put me on hold several times and said he was unsure and for me to look online
in your chat community
Then I would suggest calling back because for whatever reason the agent you spoke with the last time must not have been an Apple trained technicians, as they get this question plenty and know the answer.
Thank you for choosing the Apple Store. If you have any additional questions, please chat us again.
You are currently not in a chatAll the information you need is right here: http://www.apple.com/iphone/specs.html
Notice there is no mention of WiMax.
It doesn't really matter anyway as Sprint is rolling their WiMax network down for use by MVNOs. Actual Sprint customers will not have access to WiMax at all. It was a failed experiment. -
Does the 6600GT-VTD128 support video capture?
Hi,
I recently purchased an MSI 6600GT-VTD128 video card. The product information seems to suggest that the card has video input capabilities, and there is an adapter that plugs into the card that has a number of connections, one of which is labeled S-Video in. However, I haven't been able to get any video capture to work.
Does the card actually support this functionality? If not, what are the video input connections for? If so, is there some documentation as to how to set it up?
So far, I tried installing the video capture drivers that come with the card. I checked the manual. I checked the MSI web site FAQs. And I searched the forums.
Any help would be greatly appreciated.
Thanks,
DanielThanks Richard. Yes I do have a breakout cable like that. Actually, I described it in my original message. So, I am guessing from your message that you believe that the card should have the capability to capture video.
In my original message, I asked if there was any documentation on setting up the card for video capture. The manual does not describe the procedure, nor does the MSI web site.
There are drivers on the CD that claim to be for video capture, but they had no effect when I installed them. In fact, there appears to be no way to tell whether the drivers were actually installed successfully.
If anyone out there has successfully used this card for video capture, please let me know. -
Does the cannon mx410 support ipad printing of notes from the notepad
Does the cannon mx401 support iPad (Via wi-fi) printing from the notepad area?????
I need help getting mine to operate..
.thnx
. BeaAccording to the link below that printer doesn't support Airprint.
See requirements for AirPrint and printers that support AirPrint here:
http://support.apple.com/kb/ht4356
You may be able to print some content using a printing App from the App Store. See Print n Share, etc. -
Does the macbook pro supports the logitech gamepad 510/710? I't doesn't recognize it
Does the macbook pro supports the logitech gamepad 510/710? I't doesn't recognize it.
Is for playing to the FIFA 2012 for Macjuliafrancine wrote:
I've tried looking for the install cd for it but I can't find it, now I'm starting to wonder if it even had one.
No. 10.7 never came one a disk. Read this:
Restoring iLife applications after Internet Restore of OS X Lion
If you reinstall Lion on a new Mac that shipped with OS X Lion installed, on an erased or replaced hard drive, you can download iPhoto, iMovie, and GarageBand from the Mac App Store.
After installation, start from Lion.
Double-click the App Store icon in the dock.
Enter your Apple ID and password.
Click Purchases.
If you haven't previously accepted your bundled iLife applications within the Mac App Store, you should see your iLife applications appear in the Accept portion of the screen. Click Accept.
You may be asked for your Apple ID and password once again. Your iLife applications now move to the Purchased section. These applications are part of the software that came with your Lion based computer. Your account will not be charged for them. Click Install to compete installation of your applications.
http://support.apple.com/kb/HT4718 -
Does the ME3400 switch support MDI/MDI-x autocross
Does the ME3400 switch support MDI/MDI-x autocross? I recently experienced a situation where when the switch was set to a fixed 100 Full duplex and the outboard device selected the wrong pair, they would never link.
Is MDI/MDI-x only supported on auto-negotiation?“Thank you for your question. This community is for Cisco Small Business products and your question is in reference to a Cisco Elite/Classic product. Please post your question in the Cisco NetPro forums located here: http://forums.cisco.com/eforum/servlet/NetProf?page=main This forum has subject matter experts on Cisco Elite/Classic products that may be able to answer your question.”
- Switches ----> Network Infrastructure Forum http://forum.cisco.com/eforum/servlet/NetProf;jsessionid=E0EEC3D9CB4E5165ED16933737822748.SJ3A?page=Network_Infrastructure_discussion -
Does the iPhone 5s support LTE Advanced?
ihave iphone 5s but
Does the iPhone 5s support LTE Advanced?Galadari wrote:
Does the iPhone 5S support LTE Advanced
I assume you mean Voice over LTE (VoLTE)? If so, I do not believe it does. It certainly doesn't with my carrier (Verizon). -
HT6154 Does the iPhone 4s support Blue Tooth?
Does the iPhone 4s support blue tooth?
But not all Bluetooth profiles are supported. What is it you wish to do/connect to via Bluetooth?
-
HT204387 Does the IPhone 4S support NFC technology for Bluetooth pairing?
Does the IPhone 4s support NFC technology for Bluetooth pairing.
NFC and bluetooth are not the same thing.
The iPhone (no currently existing model) does not have the hardware required for NFC. -
Does the mozilla OS support sony xperia tipo(single sim)?
Does the mozilla OS support sony xperia Tipo(single sim) ?
If yes how would i be able to install it in my mobile phone and will it function properly and smoothly ?You can get start from here:
*https://developer.mozilla.org/en-US/docs/Mozilla/Firefox_OS/Porting
*https://developer.mozilla.org/en-US/docs/Mozilla/Firefox_OS/Preparing_for_your_first_B2G_build
*https://wiki.mozilla.org/B2G/Porting
btw, This is support forum, we dont handle this type of question, however you can ask porting related help at b2g mailing list or [https://www.mibbit.com/?server=irc.mozilla.org&channel=%23b2g irc channel].
*[email protected]
*irc://irc.mozilla.org/b2g -
Does the new IPAD3 support the 3G in Egypt?
does the new IPAD3 support the 3G in Egypt?
The New iPad supports 3G world-wide wherever there is a local provider of iPad data plans and iPad micro sim cards. Read the specifications. http://www.apple.com/ipad/specs/
So the question really is, are there 3G providers in Egypt who support the iPad? -
Does the new ATV3 support DTS?
Does the new ATV support DTS?
Hi, sorry for delay in getting back, having checked the info of one of the files it shows the following.
Apple lossless audio file
29.2mb
1253kbps
44.100khz
Stereo
16 bit
Encoded with itunes 11.1.0.126
Doesnt mean much to me but hopefully it does to hou. -
Does the new iwork support arabic language
does the new iwork support arabic language?
mhmayad wrote:
does the new iwork support arabic language?
iWork apps like Pages can usually display Arabic correctly but have various bugs that probably make them unsuitable for this language for most purposes. -
Does the iPod nano support MP4 files?
Does the ipod nano support mp4 files?????
Hi uptight,
Yes, the iPod Nano does support MP4 files.
You can find more information about the files the iPod supports here: http://www.apple.com/ipodnano/specs.html
You can convert many videos right from iTunes. This article: http://support.apple.com/kb/HT1211 will walk you through the process with sample files.
-Jason
Maybe you are looking for
-
"perfboost.exe" error during Office 365 Pro Plus Patch Update (via SCCM)
When deploying a newer version of Office 365 Pro Plus to a client machine a pop-up appears with a error message as shown below: Things I've done to rectify include: Re-downloading Office & Redistributing before retry Re-imaged computer to ensure a fr
-
I have never seen this one before - a print job that magically reappears over and over after being deleted. Does anyone know what this is? Has anyone seen this before? Here are the specifics: Printer is and HP laserjet connected via USB to computer A
-
Have the Adobe Muse CC (2014) licensing issues been resolved?
Have the Adobe Muse CC (2014) licensing issues been resolved? I am patiently waiting for some word on whether I can go ahead a install the new version of Muse CC (2014) software on my systems without running into the quagmire that so many are experie
-
Configuring more than 2 standby database
Hi, iam trying to configure 2 standby databases my primary database name is anupp1 and standby database name is anups1 and anups2 respectively (physical standby databases)when i configured means archiving is received at both databases but when i swit
-
Why won't the latest version of Adobe Flash install on my MacBook Air running Mountain Lion
Anyone else having difficulty installing Flash to their Mac?