DPM 2010 - Consistency checks stops after 23 hours

When running a consistency check on a very large amount of files, the checks repeatedly stops after 23-24 hours.
How do I solve this, so that I get a full consistency check and a good replica?
Please visit http://www.bleumer.eu

Hi,
OK - I'm not aware of any known DPMRA crash issues for DPM 2010 UR7 - so this will need to be investigated by getting the crash stack and possibly a process dump. Please open a support ticket for investigation.
In the meantime - run a chkdsk /f against the DPM replica volume to be sure we're not crashing due to a file system problem.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT]
This posting is provided "AS IS" with no warranties, and confers no rights.

Similar Messages

Secondary DPM (2012 R2) Issues: synchronising too much data from Primary DPM, persistant consistancy checks, and no dedup support!

I have a Primary DPM server that is protecting various File servers and a Exchange DAG. Everything is working as it should on this server, but I am experiencing constant issues on the secondary DPM protecting these same data sources.
On the primary, two Protection Groups in particular are set up to protect two different volumes on the same file server. Volume D:\ is 46TB in size, with a deduplicated file size of 22TB (actual 39TB) whilst Volume E:\ is 25 TB in size, with a deduplicated
file size of 2.5TB (actual 5.5TB).
Issue 1:
As expected Volume D: was initially replicated to the secondary DPM server at its undeduplicated size ( 39TB), as was Volume E:\ with initial replication to the secondary of 5.5 TB. So when is Microsoft going to support dedup on a secondary DPM ? It
seems daft to support dedup on the Primary DPM which is always more likely to be close to the original datasources on the LAN and not on the secondary DPM which is most likely to be placed offsite on a WAN !
Issue 2:
I have a big issue with the subsequent Synchronizations on the secondary server for E: which seems to transfer almost the full 5.5 TB every day ( I have it set to sync every 24hrs) - although the data is fairly static (i.e.unchanging) on that volume. On
one occasion a Sync continued for over 48 hours for this volume and had transferred over 20GB (according to the DPM console) , until I manually cancelled the job - how is that possible on a volume with only 5.5 TB (UN-deduplicated) ?? What is going on here
- has anyone any ideas?
Issue 3:
Another File server I am protecting on both the Primary & Secondary DPM server - always fails over to a consistency check on the secondary server - usually due to the fact it cannot access a particular file which results in an inconsistent replica .
However the Sync (and subsequent restore point) on the primary DPM server from the original datasource is always completes without any issues. Again, has anyone any clues ?
I do get the impression that the whole Secondary DPM thing is not quite robust enough. I can only assume that as the Primary seems to protect the original datasources ok, that the issue is with the secondary reading the information on the primary DPM.

I tried changing the time of the synchronization, but that didn't help.
Meanwhile, I was working on another unrelated case with Microsoft and so I didn't want to have a second case open at the same time. So I waited for some weeks with no change on this problem. Then, about a day or two before I was finally going to call Microsoft
to open a case (months after the problem had started), the problem suddenly resolved itself, with no input from me! So I don't really know if it was time that fixed it eventually or what. Sorry I can't be of more help.
Rob

Obiee 11g RPD consistency check error after upgrade

Hi,
got below error in RPD consistency check after upgrading from obiee 10g to obiee 11.1.1.6.
*ERRORS:
Business Model Core:
[38028] Logical column Dim - Contact.Age Range does not have a valid data type.*
logical column Age=
CASE WHEN "Core"."Dim - Contact"."Age" < 18 THEN 'A: <18' WHEN "Core"."Dim - Contact"."Age" < 25 THEN 'B: 18-25' WHEN "Core"."Dim - Contact"."Age" < 35 THEN 'C: 25-35' WHEN "Core"."Dim - Contact"."Age" < 45 THEN 'D: 35-45' WHEN "Core"."Dim - Contact"."Age" < 55 THEN 'E: 45-55' WHEN "Core"."Dim - Contact"."Age" < 65 THEN 'F: 55-65' WHEN "Core"."Dim - Contact"."Age" IS NULL THEN 'Unspecified' ELSE 'G: >65' END
above is formula for logical column "Age" and data type for that is varchar in physical
few more erros similar to above.
how can I fix the issue? appreciate for your help.
Thanks
Jay.

HI,
As I said, Age has valid datatype in physical layer but datatype is showing as "Unknown" in logical layer after upgrade to 11g. many other columns got same issue just for this logical table. I rebuild the logical column mapped to physical sources but it didn't fix the issue.
I hope you understand the issue.
Thanks
Jay.
Edited by: Jay on Jul 23, 2012 11:02 AM

Global Consistency Check Errors after RPD Merge: 38120 and 38015

Dears
Can anyone of you point me to a documentation explains Global Consistency Check error numbers in details ?
After merging 2 RPDs, it gives me the following errors: 38120 and 38015
Thanks

38120: Dimension xyz is not associated with any table(s)
Comments: I checked this Dim table and did find tables associated with it. Don't know how else to check ?
38015: Physical tables "<ABC>"."Fact - abc" and "<ABC>"."Dim - lmn" have multiple joins. Delete new foreign key object if it is a duplicate of existing foreign key.
Comments: I did check the joins between this Fact and Dim table and found only 1 join.

Flash stops after 36 hours from running...

hi friends,
i have a problem since 2 weeks.. i write a as3 program. Program is getting data from xml files (4 files) and display to the screen between 30 seconds spaces. But program is running no error 36 hours. After 36 hours flash say this error code and stops.
Error: Error #1502: A script has executed for longer than the default timeout period of 15 seconds.
at flash.utils::Timer/tick()
Error: Error #1503: A script failed to exit after 30 seconds and was terminated.
at fl.managers::FocusManager/removedHandler()
Error: Error #1502: A script has executed for longer than the default timeout period of 15 seconds.
at KCekmeceBelediyesi_SonrakindenDevam_tweensiz_fla::MainTimeline/akisaGoreGit()
at KCekmeceBelediyesi_SonrakindenDevam_tweensiz_fla::MainTimeline/akisaGoreGit()
at KCekmeceBelediyesi_SonrakindenDevam_tweensiz_fla::MainTimeline/sonrakiAkisaGececekHaber()
at flash.utils::Timer/_timerDispatch()
at flash.utils::Timer/tick()
what can i do ? thanks for relations.

hi, i have a few timers in my program.
and timers are very complicated in my codes.
and i am very carefull for use timers. i dont want every time write a new timer() command. i write every time " timer.delay= " but still error
for this reason i must c/p all code here. your solve is very long time. (there is 713 lines in my code) if you want i can sent fla file to you?

Lion install stopped after 12 hours and 3.15 GB

I bought and set Lion to download from the App Store at around 11am on an 8Mbps connection. It was going slow/fast alternately, presumably because of the heavu traffic pressure on the Apple servers. I just got an error message saying that an error occurred and the OS couldn't be downloaded. This after 12 hours and with .6 GB of completion. I don't know whether to restart it for fear of double billing or not. Anybody else who's had this issue?
Thanks and regards,
Dhruv

1.19 Mbps
So I just got an error message that Lion could not be installed and a window appeared to click "continue" to retry the installation. But when I go to the App Store, it shows Lion as "installed".

Music stops after several hours

We use our iPad to play music in our toddler's room at night to help keep her asleep. The iPad2 is plugged into an A/C source so we don't have to worry about the battery life. I manually screen lock before leaving the room. The playlist is on repeat. Everything seems find for several hours, but it will randomly just stop playing. Any idea what is wrong or what to look at? Thanks.

Welcome to the Apple Community.
Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first.

Transferring 650 gb to a new external hard drive for my time machine. It is going real slow. Says it is going to day days. After an hour or so it stops and I have to start again. When I restart, it starts where it left off. I'm not always here to resta

I have a new external drive for my time machine. My hard drive of 650 gb is full. It is reallyslow backing up to my external drive. I have to stay near by as it stops after an hour or so. If I'm not here to restart it, I lose all that time it could have been backing up. It says it is going to take 581 days. Eventually it will say 12 days. Back up time is all over the place. How can I keep the machine backing up when I sleep at night.
Gerald

I would go into your  in the upper left corner of the mac
Click on system preferences
Click on energy saver
Change the computer sleep and display sleep to never.

I can't update my ipad2 to ios5. After 2 hours and what looks like download complete and the start of processing, it stops with message check network settings and connections. Any ideas?

I can't update my ipad2 to ios5. After 2 hours of what looks like a successful download and processing is about to begin, I lose connection and get message network timed out check network settings and connection, but I am still connected via wifi. Any ideas?

If you are using windows...
Try temporarily disabling your firewall and antivirus software and try again...
See here for Connection Issues
http://support.apple.com/kb/TS1379
From Here
http://www.apple.com/support/itunes/troubleshooting/

Yosemite on 2010 MBP hangs after an hour

I'm having a strange issue similar to the one described here: http://apple.stackexchange.com/questions/151658/yosemite-hangs-exactly-every-60- minutes
I had a troublesome upgrade to Yosemite on my 2010 MBP with a custom 128 GB SSD installed. I had to abort installation and then recovered from that by reinstalling OSX via recovery mode. Now everything works fine except for the fact that the system freezes (spinning beach ball, can move windows, cannot access force quit or change focus) consistently one hour after boot. Even after several hours nothing happens and the only option is to hard reset. Booting in safe mode has the same effect.
This is obviously pretty frustrating, especially since there seems to be nothing indicating any problems in the system logs, and after a forced restart, no crash report is generated. I don't know what happened for the user in the linked thread, but our issues seem quite similar - what could this be? Some kind of daemon blocking after one hour? Some random energy saver setting whi

If you're running "Cocktail," or anything else that periodically "purges" memory, remove it according to the developer's instructions. Back up all data before making any changes.
If you're starting up from an aftermarket SSD that you or a previous owner installed (not an original-equipment SSD installed at the factory), check the manufacturer's website for a firmware update, and if there is one, apply it.

Lenovo Flex 10 touchscreen stops working after 1 hour of use.

Just bought a new Lenovo Flex 10 from a retail and it works perfectly except that after an hour of use the touchscreen stops working, the computer still works ok, but only with the mousepad. The notebook came with Windows 8.1, and I haven't installed any program on it. I need an urgent response please, since i've been looking for days in the community and other support pages, and still can't get a satisfactory answer and the period to get the a refund are about to expire.
Thanks in advance.

hi riglesias,
Welcome to the Lenovo Forums.
Once the Touchscreen stops responding, can you check the following:
1. Open System Properties and see if the Touch functionality is still there
- Link to picture (Touchscreen feature is not detected)
- Link to picture (Touchscreen feature is detected)
If the Touchscreen feature is detected, proceed to Step 2.
2. Press the Windows key‌ +R, type devmgmt.msc and press Enter. On the Device Manager, navigate to the Human Interface Devices section and uninstall anything that says HID-compliant device (this is the driver that controls the touchscreen). When finished, reboot the system and observe.
3. If the Touchscreen is still not working, hold the Shift Key and hit the restart button inside Windows and you should be able to see the image below then try to tap on the screen to test and observe. I
If the touch capability is still not functioning, I recommend you contact lenovo for service.
- Link to picture
- Support phone list
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

LabVIEW SignalExpress stops recording after 20 hours

Hi,
I'm recording 8 channel voltage using SignalExpress 2010 with USB 6221 board. I have an 8-channel recording step, a 4-channel ToAscii step and another 4-channel ToAscii step. The ToAscii goes to a USB external hard drive. I've been trying to record for 72 hours straight. I've tried 3 computers with the following results:
Windows XP - 4GB- Core 2 Duo: Computer is unresponsive after 48 hours. Have to force restart
Windows XP - 4GB- Core 2 Duo. Records for 20 hours then SignalExpress stops writing to disk. The traces on SignalExpress stop changing. But the External hard drive is still spinning.
Windows 7 - SI 2009: Same as the 2nd situation except after one hour.
I need it to be stable for 72 hours.

Hello
There,
It
seems like you are encountering a bandwidth limitation and maybe over-utilizing
the USB bus network. A good way to relieve some of the bandwidth usage is
to reduce the amount of communication/transfers on the USB network. With
that said, can you use an internal hard drive instead of a USB external drive?
Try to specify the ASCII/LVM file in a local disk instead of an external
disk. Regarding acquisition, what are the sampling rates for the analog
input channels? Sampling at a considerably fast rate will cause your
system to crash if the USB bus cannot handle offloading the information in time.
You can reduce bandwidth by reducing the sampling rate of your
acquisition. Note that the maximum transfer rate for USB 2.0 is about 480
MB/s and can fluctuate depending on various factors. I would reference
the following link below to further troubleshoot:
USB DAQ
Bandwidth Considerations and Troubleshooting
http://zone.ni.com/devzone/cda/tut/p/id/9732
USB
Specification
http://www.usb.org/developers/docs/
I hope this helps.
Regards,
Roman Sandoval | National Instruments | RF Systems Engineer

DPM 2012 Cannot modify or create protection groups after upgrading from DPM 2010

Hi,
We have recently upgraded from DPM 2010 to 2012. Since the upgrade we have been unable to create new protection groups or add new datasources to an existing group. Existing backups are running without errors.
We have tried checking the DPM sql user account permissions as described in
this article but with no luck. More searching has not provided any other relavent fixes. We are now stuck on how to troubleshoot this any further.
In the DPM console we get the following error adding a VM to an existing protection group:
Modify protection group: Virtual Machines failed:
Error 207: An unexpected error occurred on DPM server machine during a VSS operation.
Error details: VssError:Shadow copying the specified volume is not supported.
(0x8004230C)
Recommended action: Retry the operation.
Allocate Replica For \Backup Using Saved State\Cacti failed:
Error 207: An unexpected error occurred on DPM server machine during a VSS operation.
Error details: VssError:Shadow copying the specified volume is not supported.
(0x8004230C)
Recommended action: Retry the operation.
In the event log we see:
The description for Event ID 955 from source MSDPM cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
The consistency check resulted in the following changes to SQL Server Agent schedules: Schedules added: 1 Schedules removed: 1 Schedules updated: 0.
Problem Details:
<ConsistencyCheck><__System><ID>26</ID><Seq>1534</Seq><TimeCreated>23/04/2012 09:33:29</TimeCreated><Source>SchedulerImpl.cs</Source><Line>719</Line><HasError>True</HasError></__System><Tags><JobSchedule
/></Tags></ConsistencyCheck>
the message resource is present but the message is not found in the string/message table
Thanks in advance for any advice.

Hi,
The error 0x8004230C VSS_E_VOLUME_NOT_SUPPORTED: Shadow copying the specified volume is not supported, can only come when trying to enable shadow copies on new volumes created when trying to add new datasources to protection. Generally speaking
Only NTFS volumes greater that 1GB with a minimum of 300MB free space can be shadow copied, so something is going wrong with the volume creation / format process. Please investigate that, see if two new volumes get created when protecting a new data
source, and the sizes are greated that 1GB and also verify it's formatted NTFS.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. Regards, Mike J. [MSFT]
This posting is provided "AS IS" with no warranties, and confers no rights.

Why did my iMac fan come on very noisy after 1 hour of use ? I had to turn it off to stop it

Why did my iMac fan come on very noisy after 1 hour of use ? I had to turn it off to stop it

Just updated details - os x 10.8.5 .....
found an answer that could have been problem with CPU and a runaway application (possibly Bin Weevils) which my son was running at the time. I shall check the activity monitor next time to see what percentage cpu is being used..
http://support.apple.com/kb/TS1473
thanks for response

Very slow consistency check after upgrading from 2012 RU3 to 2012 SP1 RU5

this morning we upgraded the dpm server 2012 RU3 in steps to sp1 / ru3 / hotfix and then ru5
Everything went fine but problems started with the consistency checks on the large disks. They take forever(50mb per minute).
We never saw this behaviour before. Is there anything i can do to speed up the checks?
! UPDATE ! Still expirience the same problems. Doing a consistency check on a 600Gb disk and it is running for more then 8 hours now.

No sorry. Still no real solution. It looks like Windows Server 2003 is responding slower then 2008. But a real solution not found yet.

DPM 2010 - Consistency checks stops after 23 hours

Similar Messages

Maybe you are looking for