DV camera loses output connection

I recently upgraded to FCE 401, and since than when editing the image on my TV the screen picture keeps going off to black, and has to be brought back using the 'reset devices command'. I have a panasonic NS250B which is a few years old but worked perfectly with FCE 2. This is an annoying habit, that is holding me back, as I edit off the screen. Any idea why this has happened or how to resolve it? settings?
Thanks.

So, to be clear, you are monitoring the image on a TV through your camera? Make sure +View > Video Out > Apple Firewire+ is selected.

Similar Messages

USB audio device loses output connection

I use a MobilePRE USB interface and had no problems until recently. My iMac is set to never sleep but if I do not use the computer for a few hours the output from the MobilePre is gone.If I change to the driver to the internal headphone output on the Mac all is fine but in order to use the MobilePre as output I must restart, then it is fine until the next day or a few hour later.
The same time that this problem developed, about a month ago, I also noticed a low level snap or popping sound. This happens through my external speakers and is triggered by any sound activity approximately 30 seconds later. It even happens with the volume turned all the way down and sounds like a connection is being made. Like I said these two problems started about a month ago around the time Apple was sending a lot of updates. I have read a long thread on the OSX forum and know this is a pervasive problem with no solution yet. I mention it here as a curiosity as it started around the same time as the USB audio device problem. My hunch is that it has something to do with a recent update.
I don't think this is a GarageBand problem because it is the same no matter what software is outputting. I ask on this forum because there some knowledgeable audio heads here.

Check the archlinux news item which calls for an entry in kernel commandline .................

MacBook loses wireless connection when iPod touch connects to network

hi
ever since upgrading to 10.5.5. on my MacBook i've had the "intermittent network connection" problems that have been described and discussed (without any real solution from what i can see) in another thread.
PROBLEM: every couple of minutes my MacBook loses connectivity to the network - the AirPort icon still says that i'm connected, albeit with one less bar than before, but i can't connect to anywhere, not even to the wireless router - and to re-establish a connection i need to switch off AirPort, switch it back on, it will then reconnect, and after two minutes or so i have to do it all over again because the network connection drops again.
NOVEL OBSERVATION 1: reinstalling the 10.5.5. combo system updater helped somewhat. i used to get an error in system.log about there being too many state transitions on the wireless network and about network traffic reduction measures being taken to overcome this problem, but after reinstalling the 10.5.5. combo system updater this message never appears in the logs and I get kicked off only sometimes (see what i say in point 2 below)
NOVEL OBSERVATION 2: now my MacBook will only lose its connection to the net if i switch on my iPod Touch and switch its wireless interface on. in fact, the only way to avoid the MacBook getting constantly disconnected is to make sure that the wireless interface on the Touch is switched off in the Touch's system preferences; if I just sleep the Touch (top button) without switching off its wireless network interface first in its System Preferences, then the MacBook will keep disconnecting even while the Touch is in sleep mode (presumably the Touch keeps polling the network or something, even while it's in sleep mode).
DIAGNOSTIC NOTE 1: I have another wireless device (my Nokia E51, which has wifi capabilities) and if I connect it to the wireless interface then the MacBook's connection isn't dropped - i.e. the MacBook only loses its wireless connection when my iPod Touch connects to the wireless network.
DIAGNOSTIC NOTE 2: I have upgraded my wireless router (before I had a Linksys WRT-54GC, now I have a Netgear WGR614v9) but that has made no difference.
DIAGNOSTIC NOTE 3: I have also tried altering the router's settings (i have played around a_lot with this, trying every combination I could think of - e.g. staple down particular devices to particular ip addresses, use only 802.11g versus automatic b/g, etc) but that has made no difference either.
RANT:
The only thing that prevents these disconnections from occurring is to keep the iPod Touch's wireless switched off, which ***** because if I'm in the kitchen I can't have it switched on to monitor my email (yes, I've no life, i hang around waiting for emails), or if I go have a lie down and want to check out stuff on the net, or to browse the iTunes music store or whatever, then I know that my connecting my iPod Touch the computer will be disconnected.
This obviously *****, right? And a lot of people are having wireless problems with their MacBooks, right? And these problems seem to have been around for over a year, right?
So why hasn't Apple solved this problem yet? Or am I just being melodramatic?
Your thoughts on any or all of the above, or flames if that's your preferred method of communicating, are invited. =)
Cheers
dr.colekat

Having the same problem here. As a first time mac user, Apple has certainly made a bad first impression.
For me, the issue seems to occur when transferring files between computers that are connected to the same access point (when transferring files from wired computers on the network there is no issue). My vista laptop and every laptop I have tried has worked perfectly fine with this access point so I am 100% convinced it is the mac. Basically when I copy the files, after about 100mb, I am unable to access anything on the local network or internet until I restart Airport. The weird thing is that even though I am unable to access anything, the airport utility says it is connected. I might also note that the wireless signal strength is full.
If I can't get this figured out in a few days, this computer is going back to the store where it came from and I will officially label myself anti-mac. This type of issue is just unacceptable for something so main stream.

AirPort Extreme loses ethernet connection

I am running about 20 or so base stations in my school and every once in a while, a couple of the stations loose their ethernet connection. They are still broadcasting wirelessly, but they disconnect from the network. The stations are running fw5.6 and my clients are running 10.4.2 or WinXP SP2. The only way to fix the problem is to power cycle the base station. I also have the older graphite stations which work fine, which leads me to think that this is not a network issue.
Any suggestions?

I also lose ethernet connection. Sometimes once a day, other times 10 times per day. The other day I was so frustrated about losing my connection that I just walked away from it, without cycling power. When I came back (about 30 minutes later) from my cooling-off period, I found that the connection was back. So, with my AirPort Extreme, cycling power is not the only solution. It's not an acceptable solution though.
I was wondering what you mean by your statement, "They are still broadcasting wirelessly, but they disconnect from the network." I'm relatively new to this stuff and this baffled me, which isn't hard to do.

Itouch loses wifi connection constantly

itouch constantly loses wifi connection, similar itouch has no such problem, updated software to latest version available but issue persists

Additional information, I have D-Link router that came free when I signed up with my cable company so I'm sure it's a basic model. I did update the firmware to the latest and greatest as well.

All devices on network lose internet connection when Dell laptop connected

I have successfully setup my AEBS network and am using two wireless clients--HP printer and Xbox access point (both 802.11 G) and a wired iMac that also is connected via Airport (so I can move it around if i want). I tried connecting my Dell Latitude D830 wirelessly and within a few minutes of connecting the AEBS loses internet connectivity. Unplugging and restarting the AEBS restores the internet but it just drops off again in less than 10 minutes. My question is, what might be causing this and what can I do about it? One peculiar thing to me is that I am using the WEP security option since the Xbox doesn't seem to support WAP2. When connecting the Xbox it reports the network as WEP but the HP printer and Dell Laptop but suggested the network was indeed WAP even though I'm clearing using WEP security. Maybe it's nothing but wanted to add for completeness.
The Dell is running Vista Enterprise edition.
Thanks for any help.

I've noticed a similar issue. Any time my HP/Vista laptop is connected to my AEBS it loses the network connection at inconsistant time intervals(~10-15 min).

I lose the connection when closing the CMD

Hi guys,
I have configured a standalone listener as following:
C:\Program Files (x86)\Java\jre6\bin> java -Dapex.home=D:\list -Dapex.images=C:\images -jar D:\apex.war
Afterward,
If I close the CMD, I will lose the connection, and I have to reconfigure it again.
If I open APEX locally , I mean by using the shortcut "Get Started With Oracle Database 11g Express Edition" , Then I will lose the connection that uses the default port of the listener, that is 8080.
After I configured the listener I got this message on the CMD
-- listing properties --
PropertyCheckInterval=60
ValidateConnection=true
MinLimit=1
MaxLimit=10
InitialLimit=3
AbandonedConnectionTimeout=900
MaxStatementsLimit=10
InactivityTimeout=1800
MaxConnectionReuseCount=1000
APEX Listener version : 1.1.2.131.15.23
APEX Listener server info: Grizzly/1.9.18-o
May 21, 2011 5:14:41 PM com.sun.grizzly.Controller logVersion
INFO: Starting Grizzly Framework 1.9.18-o - Sat May 21 17:14:41 GST 2011
INFO: http://localhost:8080/apex started.
Using JDBC driver: Oracle JDBC driver version: 11.2.0.2.0
Regards,

Hi,
I'm not sure I got your question right, but I'll try to find some solution anyway.
If I close the CMD, I will lose the connection, and I have to reconfigure it again.That's what happens when a shell is terminated - all associated processes will stop as well. However, if you have a apex-config.xml in your apex.home you shouldn't need to configure your APEX Listener each time your start it, but it would reuse an existing configuration.
If I open APEX locally , I mean by using the shortcut "Get Started With Oracle Database 11g Express Edition" , Then I will lose the connection that uses the default port of the listener, that is 8080.Now, if you have XE running on the same (local) machine as you have your APEX Listener running in standalone mode, you probably have a port conflict: By default, both APEX Listener in standalone mode and the Embedded PL/SQL Gateway (EPG) use port 8080. The EPG is activated as web server for APEX in XE after a fresh installation, the APEX Listener would be an alternative in that case. You can either stop the EPG, or reconfigure any of the two web servers to use a different port, if you want to run them parallel.
To change the port used by the APEX Listener in standalone mode, you simply add another parameter to the startup: -Dapex.port=8888 and you're done.
To change the port used by the EPG, connect as sys and run the following
EXEC DBMS_XDB.SETHTTPPORT(8888);
COMMIT;If you want to disable the EPG, simply set the port to *0* .
After I configured the listener I got this message on the CMDThat's what it should look like.
No, since your topic is "lose the connection when closing the CMD", I assume you search for an alternative. You could run the APEX Listener as a Windows service, even in standalone mode. To do this, you create a batch file, e.g.
%JAVA_HOME%\java -Dapex.home=D:\oracle\APEX_Listener\_home -Dapex.images=D:\oracle\apex_4_0_2\images -Dapex.port=8888 -jar D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\apex.war >>D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\my_apex_listener.log 2>&1Note that you have to set JAVA_HOME as system property or replace the call with the absolute path to your JDK or make sure the JDK is in your PATH variable.
Of course, you can and should change the other directories as well to fit to your system.
Next, create a Windows service, e.g. using [url https://iain.cx/src/nssm/]NSSM (free) or [url http://support.microsoft.com/kb/137890]SRVANY (MS, non-free), that starts your batch as a windows service.
The command for creating that service using NSSM could look as follows
nssm install APEX_Listener D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\startup.cmdYou can edit the service properties afterwards, e.g. change the start mode from "Automatic" to "On Demand".
I hope this answers your question. If not, please point me into the right direction.
Thanks,
Udo

I lose wireless connectivity when I connect the nano to my PC

I have a DSL modem connected by ethernet cable to a Linksys wireless router. My PC has USB linksys antenna. The wireless connection works fine except when I plug in the Nano, it takes about two seconds and I lose the connection to the router. If we are in itunes downloading it is suspended. If we are on the internet the next click and the Microsoft "you are not connected to the internet" page comes up. To reestablish the internet connection I have to remove the nano and reboot the PC. Needless to say this is very frustrating.
If I reboot with the cable attached I get an error unable to run an ____.exe that I believe is the antenna setup because the linksys monitor stays gray in the startup box.
I have tried to move the antenna to a different USB port on the PC with no luck. Everything else runs fine.
Does anyone out there have any ideas/fixes? - Your assistance is greatly appreciated!

thanks deggie for your answer.
I had my ipod with autosync off ... I set it "manage like disk" .
I try to recover the music with 2 programs: "ephod" and "copy trans" ..
I can see all the songs listed, but can´t backup to disk or recover them......
I see than my ipod hasn´t the folder "ipod_control" , which appears before I had this problem....
Any idea ??? Thanks again.

New 6500 E709n loses wireless connection when it or laptop sleeps... & other problems!

Just got this printer and am hoping we can get it to work because we really like it. I believe we've done everything right - it is connected to PC via USB, and to laptop via wireless network. Both computers are Dells running XP. Our wireless router is a Linksys Wireless-G WRT54G. We installed the disk on both. Immediately after installing on the laptop by plugging in USB and then unplugging, we were able to get it to work. We printed and scanned from both . . . UNTIL the printer went into power save mode.
When it sleeps it loses all the network connections (but will still print from PC). Even the icons disappear from the laptop after it sleeps. The only way to get it to work with the laptop again is to start all over, plug in the laptop, enter the WPA key again, and so on. Then it's finebut for just a short while. Now, when I registered my protection plan, I was on the phone with a techie guy and asked him if it's normal to have to keep entering the key every time you want to print, and he actually said that maybe I shouldn't let the printer sleep - wow! I want to conserve energy, so I may even want to shut it off, okay, and I don't feel I should have to go through this rigamarole every time I want the darn thing to just be available to the network. Furthermore, what's the sense of having to turn "Wireless Radio" on and off all the time???
Anyway, there are other problems and the menus in the internal web browser is about as confusing as it can be. Is the passphrase the same as a WPA key? There's a passphrase in there which I did not enter, and I don't know what it is because it's been disguised with dots. When I enter the WPA key on the front panel of the printer, it doesn't stick. One thing I noticed in the instructions is to keep telephones away from it, so I moved ours (was right next to it) but it's still being ornery.
In addition, the scan function only works from the software, not as a standalone if I use the front panel. When using the button on the front panel, sometimes it sees the laptop, sometimes it doesn't, and then it starts to scan, but a menu pops up on the computer asking to update the buttons, and then nothing happens.
Have we a clunker on our hands that should be returned, or is there a remedy? All suggestions welcome!
Message Edited by geoxena on 10-20-2009 10:56 PM
Message Edited by geoxena on 10-20-2009 11:03 PM

Let me answer the easy stuff first:
Yes, the passphrase is the same as the WPA-PSK key.
No, it's not normal to have to re-enter the wireless security key over and over again. Politely tell our service agent that he is mistaken on this point.
There's no sense in having to turn the radio on and off all the time to get the printer to remain on the network.
When the printer goes into power-save mode, can you still access the printer's internal web page by browsing to it's IP address? When the printer loses wireless connectivity, can you wake the printer by pressing any of the buttons on the front panel?
I have a couple more questions:
What WRT54G HW version do you have (it'll be on the bottom label of the router)?
What version of FW does your router have? You'll have to browse to the router's internal web page to find out.
Finally, change the WPA-PSK group key renewal period to the largest value possible. Tell if this affects the frequency of printer losing Wi-Fi connectivity?
One more question. After you have the printer connected to your wireless network and it's working, if you turn the printer off (via the power button), wait five seconds then unplug it then plug it back in and turn it on, does it connect to your network?
Regards / Jim B / Wireless Enthusiasts
( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
+ Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

Photos won't import images from my Canon camera. When connected, program sees the images, tells me it will import the new ones, then freezes once import starts, not allowing any other operation to happen. MacbookPro 15" 2012, OSX Yosemite 10.10.3.

Photos won't import images from my Canon camera. When connected, program sees the images, tells me it will import the new ones, then freezes once import starts, not allowing any other operation to happen. MacbookPro 15" 2012, OSX Yosemite 10.10.3. Any suggestions?

Solution discovered. Faulty connector cable. Tried a different one and it worked.

When my daughter connects to our home wifi she has to be within 5 feet of the modem, once she moves upstairs she loses wifi connection and then when choosing the network, it can't find our wifi network?

When my daughter tries to connect to our home wifi, she has to be in the basement within 5 feet of our modem. Once she comes upstairs she loses the connection. All of our other devices connect to the wifi on all levels of our house, including her Dad who also got an iphone 4 and her ipod works as well as her brother's ipod and my blackberry. I have tried resetting the network settings to no avail. I have already had our modem rebooted through our internet provider so I know the signal is good (as well as all other devices connect to wifi) I am losing sleep over this and she is quite frustrated so any help would be appreciated. I'm starting to wonder if it's a defect in her phone???

Is her iPhone in a case by any chance? If so, remove the case and try again. How does her iPhone work in free Wi-Fi locations?
Try resetting the iPhone...
Press and hold the Home and On/Off buttons simultaneously until you see the Apple logo, then release. This may take up to 10 seconds. This is the equivalent of a re-boot and you will not lose any data.
If none of the above work take it to an Apple store or AASP for evaluation. She will not be charged folr this and they will suggest a solution if there is a fault.

My ipad 1 loses wifi connections when it goes to sllep. have to go into settings to reconnect. Does this all the time. please help.

my ipad 1 loses wifi connections when it goes to sleep. have to go into settings to reconnect. Does this all the time. please help.

my ipad 1 loses wifi connections when it goes to sleep. have to go into settings to reconnect. Does this all the time. please help.

Windows 7 64 bit USB external hard drives lose its connection and stops working.

This is a very serious error for users of WIN 7 64 bit only.
I have read hundreds of posts about this problem an not a word about it from MS.
We have tested this problem on four different computers and three different external hard drives using Win 7 Ultimate.
Even tried the RTM version.
If you connect "Any brand" external USB hard drive to "Any brand of computer" using Win 7 (64 bit only) and try to copy a large file like a movie from the internal drive to the external USB drive it loses the connection to the USB.
We even reverted back to Vista 64 bit on two computers for testing but Vista 64 works fine.
This occurs on all computers with different USB drives.
We have tried all the suggestions posted and none work.
It seems from all the posts that other USB devices are also having similar problems with the 64 bit.
Below is a more about this problem.
http://windows7tipsonline.com/USB_Problem.htm
If anyone knows how to resolve this please post a reply here.
Thanks

The link only refers to USB problems with nVidia chips, so it's not a universal problem. I have Win 7 x64 RTM installed and I just transfered 2 4GB DVD files and 1 18GB backup file from my internal SATA drive to my external USB drive
with no problems - no time-out!
<text>Since nVidia chipsets seem to be the culprit, nVidia and the motherboard manufacturers need to be told about the problem so that nVidia can correct the problem and not
Microsoft. If it's a nVidia chipset driver/software problem,
Microsoft is not going to fix anything since it's not a universal problem.</text>
I think this answer is a smoke screen, here's why. The issue of a USB HDD losing its connection AND not being recognized on a booting Win 7 x64 in any of its incarnations is a Microsoft issue, not nVidia. I have three PCs (actually 4 but one is in storage so
doesn't count) to see firsthand what happens with this issue. One, is a maxed out Toshiba with Windows Pro x64. Every now and then, it asks to format any number of my USB drives. I have Seagates, Iomegas, Western Digitals, and an OLD Maxtor. The Toshiba OS
will from time to time claim the Iomega and WD drives need formatting or have a wrong parameter etc. It doesn't do this with the Seagates or Maxtor. does the Tosh have nVidia chipsets? Yes. OK, now I attach these dives to my Dell Inspiron run by Windows Vista
Home Basic and intel Graphic Chip. The HDDs fire up right away. OK, I stick them into the ASUS G75VW-RS72, a DTR notebook on Windows 7 Ultimate x64. The machine has nVidia chipsets. Sometimes the HDDs fire up right away (Maxtor is never a problem), sometimes
they don't. What do I do? Unplug, replug-sometimes works sometimes not. Turn off the computer, turn it back on-sometimes works sometimes not. Unplug and put into another USB port-sometimes works sometimes not. Unplug and leave unplugged for anywhere
from 10 seconds to half an hour-sometimes works sometimes not. Switched to different external enlosure or the same or different brand-sometimes works sometimes not. Remove the HDD and put into a NetStar portable dock with its own power supply(http://www.vantecusa.com/en/product/view_detail/295).
Result? The computers NEVER, not EVER, even ONCE demonstrated an issue with the drive. Other times, I remove the HDD and employ a converter (http://www.sabrent.com/category/hard-drive-enclosures/USB-DSC5/). Result? The computers NEVER, not EVER, even ONCE
demonstrated an issue with the drive. So I think the evidence suggests Windows is finicky and Microsoft is passing the buck on this.

HT4101 I can't use my lightning to USB camera adapter to connect my new Sony Cybershot DSC-W730 to my new ipad Air. It says the connected device needs too much power. Any ideas what to do?

Has anyone a solution to my newly purchased lightning to USB camera adapter not connecting my Sony Cybershot DSC-W730 to my new ipad Air? It says the connected device requires too much power.

Use the camera's SD card.
 Cheers, Tom

Disconnected camera appears as connected device - can't get rid of it!

I recently connected a Samsung Galaxy Tab (SCH-I905) to my Mac, and because it had a photo on it, iPhoto started up and wanted to import the photo. I did that, and ejected the device and all seemed well.
But now whenever I start up iPhoto, the SCH-I905 appears as a connected device even though it is not connected. An empty dotted line rectangle appears in the main pane showing there is allegedly 1 photo on it, but there is no thumbnail image for it, and if you try to import it you get an error "The following file could not be imported. The file is an unrecognised format" (even though the original file was jpg).
Further, this problem seems to be stopping iPhoto recognising my digital camera when I connect it - it doesn't appear. The Image Capture app is similarly affected - it thinks the SCH-I905 is connected and refuses to recognise my digital camera.
I have tried trashing iPhoto preferences - no difference.
According to System Profiler and USB Prober, the SCH-I905 is not connected, but my digital camera is. So the USB is working but iPhoto is ignoring it.
I can control-click the SCH-I905 icon in the left pane of iPhoto to "Unmount" it and the icon goes away, but my digital camera is still not recognised even if I unplug it and plug it back in again, and if I quit iPhoto and restart, the dreaded SCH-I905 comes back.
HELP! How do I permanently unmount "SCH-I905" and restore sanity?
iPhoto '09 (version 8.9.2)

Try trash the following file
com.apple.ImageCaptureNotifications.DeviceDiscoveryDatabase.501
from HD/Library/ Caches
and restart your mac.

DV camera loses output connection

Similar Messages

Maybe you are looking for