Dynamic interface: dynamic AP management + NAT enabled

Hello,
I would like to ask for I have not found any supporting documents with regard to my concern.
I would like to deploy our 2504 WLC connecting 600 Series OEAPs to it using a dynamic interface with dynamic AP management and NAT enabled disabling the management interface's dynamic AP management and NAT. Apparently, I was not able to connect the OEAPs to the WLC. But if I change the setting in using the management interface instead of my created dynamic interface, with dynamic AP management and NAT enabled, the OEAP successfully joins the controller.
Are there any solutions that I could use a dynamic interface as ap-manager with NAT or is it that the management interface can only be used?
Cheers!

IIRC, you need the OEAP to join to the management address since that is where you will be entering the nat'd address. So using a dynamic interface will not work and really can only work when APs are local mode.
Sent from Cisco Technical Support iPhone App

Similar Messages

GRE over ip nat enable

Hi, guys
recenctly I switch from ip nat inside to ip nat enable, but when I use ip nat enable my microsft vpn dosent work.
interface GigabitEthernet0/1
ip nat enable
interface GigabitEthernet0/0
ip nat enable
ip nat pool pool-vrf-blue 204.x.x.100 204.x.x.100 netmask 255.255.255.0 add-route
ip nat source list NAT-VRF-BLUE pool pool-vrf-blue vrf blue overload
ip nat source static tcp 10.0.0.2 1723 204.x.x.100 1723 vrf blue extendable
Best regard

Ok - This is what I currently have:
interface FastEthernet0/0.22
description NAT INT for VRF TEST to ERT02-BNE
encapsulation dot1Q 22
ip address 203.149.77.38 255.255.255.252
ip nat outside <-- Also tried "ip nat inside"
no snmp trap link-status
ip route 203.149.77.44 255.255.255.252 Null0
ip route vrf TEST10 0.0.0.0 0.0.0.0 FastEthernet0/0.22 203.149.77.37 global
ip nat pool NAT 203.149.77.45 203.149.77.46 netmask 255.255.255.252
ip nat source list 1 pool NAT vrf TEST10 overload
access-list 1 permit 10.0.0.0 log
access-list 1 permit 192.168.1.0 0.0.0.255 log
Attempting to get(trace/ping) to any address not within the vrf TEST10 (From device in vrf TEST10) results in timeout at 203.149.77.38 router.
Trace'ing with a source IP of 203.149.77.38 to an Internet address is successful
#sh ip route vrf TEST10
Routing Table: TEST10
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 203.149.77.37 to network 0.0.0.0
10.0.0.0/8 is variably subnetted, 6 subnets, 2 masks
C 10.0.0.2/32 is directly connected, Virtual-Access7
B 10.0.3.0/24 [200/0] via 203.149.76.248, 3w0d
C 10.0.0.0/24 is directly connected, Loopback10
B 10.0.6.0/24 [200/0] via 203.149.76.250, 1w5d
B 10.0.7.0/24 [200/0] via 203.149.76.247, 1w4d
B 10.0.5.0/24 [200/0] via 203.149.76.249, 3w6d
U 192.168.1.0/24 [1/0] via 10.0.0.2
S* 0.0.0.0/0 [1/0] via 203.149.77.37, FastEthernet0/0.22

Using both Dynamic and Static NAT with two Different Internet facing Subnets

We have two Class C Public Address subnets. We started with Subnet (A) and have many of our Internet accessible devices on it. It is running on a Cisco PIX 515R. We bought a new ASA 5510 8.3(2) and started Migrating the Users and new servers to it so I started with our second Class C Subnet (B). Later on down the road I found out that if the Firewalls Default Gateway is is set to a (B) Interface subnet, then the servers that are statically mapped to a (A) Address will have a (B) address when they communicate out to the internet. So they are receiving packets on their (A) Address, though replying to them with a (B) address.
It was mentioned that I should be able to combine static and dynamic NAT mapping to allow devices behind the firewall to have a fixed external Address when communicating outbound as well as inbound.
So For instance I want the Following: when the Internal Replies I want the reply to come from the mapped IP, not a IP from the Dynamic Pool.
Public IP: 192.168.1.100/24
Internal IP: 10.0.0.100/16
Public IP: 192.168.5.101/24
Internal IP: 10.0.0.101/16
interface Ethernet0/0
description 192.168.1.0/24 Network Outside IP
nameif outside-1
security-level 0
ip address 192.168.1.1 255.255.255.0
interface Ethernet0/1
description 192.168.5.0/24 Network Outside IP
nameif outside-5
security-level 0
ip address 192.168.5.1 255.255.255.0
interface Ethernet0/2
description inside 10.0.0.0/16
nameif inside
security-level 100
ip address 10.0.0.1 255.255.0.0
object network serverA_o
host 192.168.1.100
object network serverA_i
host 10.0.0.100
object network serverB_o
host 192.168.5.101
object network serverB_i
host 10.0.0.101
object network 192-168-1-NAT-POOL
range 192.168.1.50 192.168.1.239
nat (inside,outside-1) source static serverA_i serverA_o
nat (inside,outside-5) source static serverB_i serverB_o
nat (inside,outside-1) source dynamic any 192-168-1-NAT-POOL interface
object network serverA_i
nat (inside,outside-1) static serverA_o
object network serverB_i
nat (inside,outside-5) static serverB_o
route outside-1 0.0.0.0 0.0.0.0 192.168.1.1 1
route outside-5 0.0.0.0 0.0.0.0 192.168.5.1 2
When I set this up my serverB shows a Public IP of something in the 192-168-1-NAT-POOL Not 192.168.5.101
Any Suggestions?
Thanks!

Not sure why I have Multiple Entries. )-: I did think it was Odd. I think it might be because I looking at examples of the new and old styles of NAT.
We have a Single ISP, though have 2 separate non-Contiguous Class C Addresses from them. We host some Servers on one subnet and some on the other.
I'm looking for a way to use both Subnets on the same ASA.
The Connection to the net looks like this:
Internet -> Edge Router Layer3 VLAN Switch
GE0/1.2 - 192.168.1.1 VLAN Tagged --> GE0 - VLAN Tagged
GE0/1.2 - 192.168.5.1 VLAN Tagged -^
Layer3 VLAN Switch Firewall
GE1 192.168.1.0/24 Untagged -> ASA Outside-1
GE2 192.168.5.0/24 Untagged -> ASA Outside-5
Firewall
ASA inside 10.0.0.0/16 -> Switch -> 10.0.0.100
Hope that helps clarify.
I could try to post some sanitized Configs of my PIX and ASA if needed. But the end result I'm trying to do is have the ASA do NAT for multiple Public Subnets.

Using Dynamic Memory Management

Hi All,
http://technet.microsoft.com/en-us/library/ms178145(v=sql.90).aspx
I have red the above article regarding Dynamic Memory Management and now I just want to check whether this option is enabled in my environment or not.
Is this by default enabled in the server or else Please suggest on how to achieve this
Regards,
Kalyan
Grateful to your time and support. Regards, Shiva

Is this by default enabled in the server or else Please suggest on how to achieve this
Regards,
Kalyan
Grateful to your time and support. Regards, Shiva
If you read the first line of the link you posted its clearly written SQL Server memory management is dynamic. You cannot change it . You can just restrict buffer pool usage by puttling limit on MAX Server memory. In that case as well SQL Server might cache
all Buffer pool memory.
Event though you cap max server memory still direct memory allocations for large pages will be done directly by windows API and that will also come under SQL Server memory utilization
In short SQL server memory allocation is always dynamic you cannot change it
Please mark this reply as answer if it solved your issue or vote as helpful if it helped so that other forum members can benefit from it.
My TechNet Wiki Articles

Use of ADVM (ASM Dynamic Volume Manager)

In oracle 11g 2 There is ADVM (ASM Dynamic Volume manager) is there, If i make 50GB of advm from 1TB of Disk Group. I want to know that 50Gb of Dynamic volume will use oracle db files or not.
exactly I want to place my tablespace files on that voulme.
Edited by: shayad on Sep 22, 2011 10:21 PM

Have a look at Oracle® Database Storage Administrator's Guide.
Scroll down to the diagram that depicts where ADVM resides in the s/w stack.
Why ADVM?
ASM does not only support storage for Oracle databases - but also for any other 3rd party application. The latter is done via ACFS - a cluster file system. This is similar to OCFS and Red Hat's GFS and so on.
A volume manager is used to manage such file system volumes. Linux has a default volume manager called LVM.
ADVM is a volume manager specifically for dealing and integrating with the underlying ASM storage system.
You would usually not use ADVM for ASM diskgroups used by Oracle databases (Oracle databases interface directly with ASM diskgroups and do not need a file system interface).
You can for example use ADVM to manage a cluster file system for a mySQL database - and use custom failover to fail that database over to another node should the current one fail (as the cluster file volume containing the database files will also be available on the other cluster nodes).

Cannot convert disk to dynamic because security is enabled...

I am setting up a new computer with two Crucial m500 960GB SSD drives. I have Windows 8.1 Pro installed on the first drive. I am trying to mirror it to the second drive (using Windows Disk Management), but I get the error below. I can't find
anything online regarding this error. Bitlocker is not enabled on the drive. I tried turning off UEFI Secure Boot, but that didn't help either. There is the System Reserved drive created during the Windows install, but I wouldn't expect that
to cause this problem. Any ideas?
Virtual Disk Manager
The disk could not be converted to dynamic because security is enabled on one or more partitions.
OK

Hi,
According to your description, I suggest we try safe mode to check the result.
Meanwhile,I would to know if you installed other security software on your PC.
Regards,
Kelvin hsu
TechNet Community Support

DYnamic link manager error

i have
an error which pops up everytime i open ae cs5. its part of production premium student windows 64-bit. it has worked fi ne but i started to get errors, ive attached a pic
all of the other programs still work

This can occur if After Effects is failing to communicate with the Dynamic Link manager because the communication is blocked---usually by overly aggressive firewall settings.
See this document:
http://kb2.adobe.com/cps/857/cpsid_85711.html

HT3258 dynamic memory manager

Does Apple fix the problems with the dynamic memory manager in Mountain Lion?

After more tests I can say that this memory consumption
disappear with a release version of the swf executed directly by
the browser.

How do I close Adobe Dynamic Link Manager & Adobe Media Core to install After Effects?

when i try and install the after effects cc it tells me to close the following programmes: after effects, adobe dynamic link manager and adobe media core.
How do i close the last 2??

You can also restart your computer to make sure that everything has been quite that needs to be. Restarting before and after installing major software is a good idea in general, anyway.

Premiere Pro CC and Dynamic Link Manager Issues

I have a previously purchased copy of Adobe Production Premium CS5 installed on my computer as well as a subscription to CC with a few apps installed.
I had a project opened in Premiere Pro CC, off of an external hard drive, and as I was working on it, trying to open it in Speedgrade. I decided to install Audition. However, it prompted me to close the dynamic link manager. Once I did, my project began messing up. As I tried to open the program, my sequences and merged clips disappeared and I don't know what to do. My semester project is due tomorrow. Premiere won't let me open the file (neither cs5 and CC) and the ones that do open have all the clips but no sequence nor merged clips that I previously had. I did notice that the dynamic link is no longer opened in task manager after restarting and restoring the system(with the ejected hard drive). How do I reopen it? And, will it solve the problem?

Thank You, Jim -
Unfortunately that specifically did not work.
Based on another comment sent to me, here is what did.
In PProCC
File > Adobe Dynamic Link > New After Effects Composition
In AECC
From that composition created from PPro, I imported the project (aep) initially created in AECC from another team member. Saved the file.
Back in PProCC
File > Adobe Dynamic Link > Import After Effects Composition
Magic.

Dynamic Link Manager repeatedly crashes when trying to launch CC applications

Whenever I try to launch most CC applications, the application locks up and becomes unusable for a few minutes. When it locks up varies slightly between applications (Premiere Pro and After Effects locks up when launching, Photoshop locks up shortly after presenting the main window, ect.). I checked the console after noticing this was happening repeatedly, and saw the following message repeated once a second (with an iterating instance number):
10/27/13 3:56:13.725 PM com.apple.launchd.peruser.501[258]: ([0x0-0x5b05b].com.adobe.dynamiclinkmanager.application[537]) Job appears to have crashed: Abort trap: 6
10/27/13 3:56:13.773 PM ReportCrash[514]: Saved crash report for dynamiclinkmanager[537] version 7.0.0 (7.0.0.0) to ~/Library/Logs/DiagnosticReports/dynamiclinkmanager_2013-10-27-155613_lrflew.crash
I uploaded the log file mentioned in the console here: http://pastebin.com/iWBiykSP
I am using a Macbook Pro Retina, 15-Inch, Late 2013 running Mac OS X Mavericks (10.9).
Is anybody else having similar issues? Is there an update I don't know about for the Dynamic Link Manager that fixes this issue? Should I submit a bug report for this?

I came across this post while searching for a sollution to my problem. I came a cross a lot of posts like this and they all seem to have a common theme with Adobe CC paid beta. Granted I wrote a prolific rant I cannot seem to spell check, go to the last paragraph [the short version] and it will explain how to solve this. grrrr....
I noticed that CC keeps forgeting who I am, asking me to log in, updating, changing prefernce, not remembering my cloud settings, it has been awfull. I like the new features, but I feel like Adobe is restting all my macros and pressets every other month.
That is what led me to my conclusion of what is going wrong. Every time I wanted to put After Effects dynamic link Premiere would hang. I had to force close it via Windows 8. I first suspecting Windows 8 to be the problem, I turned off my UAC, I turned off my start screen, ran as admin, even tested it with the admin account. That worked. I tested it with another account., that worked. So everything worked but the account I needed to work. DARN YOU MICROSOFT!!! **fist shaking**
I then thought, "crap, what if they deleted this feature?" "No, they couldn't, this feature is the primary reason why I bought the softwear instead of trying to rip it off (poor college student first job card) Still I found the money to buy the software for this feature, now it is gone???!!!
That is when it occured to me, this was exactly like the crack versions I used of 5???
Hmmm ..
I turned off all my adobe services, rebooted, cleared cache, everything, what the hell.
Then it came to me, what if it thinks i am not who I say I am. After ...
[Short Version] Log out of Creative Cloud then back in.] If you have any issues that seem random make this your first step. Adobe as botch this granted, I believe in them, I think they should extend the $19.99 discount fo another year because of it and the fact we would still be willing to pay that. seriously Adobe, get the poop together or start compinsating your customers.

How to turn the elements auto analyzer and dynamic link manager off?

While I was installign the trial version of photoshop cc, a question popped up asking me to turn elements auto analyzer and dynamic link manager off, but I couldn't find them. Please help me

Terminate the processes in Task Manager/ Activity Monitor.
Mylenium

My CS6 Production premium upgrade - Dynamic Link Manager.

My CS6 Production premium upgrade hangs up on install. Asks me to close Dynamic Link Manager. A search on mys system for dynamic link manager comes up empty.

I found this thread eventually. Thank you MinorMakesWork.
solution worked perfectly for me.
2. MinorMakesWork,
Jun 18, 2013 10:33 AM in reply to LumLan
Report
I believe you need to go into your utilities folder and open "Activity Monitor"...look for Dynamic Link Manager in there. then quit the process. I had to do that to install my cs6.

Trouble with dynamic link manager in starting a cs6 product

i just re-installed cs6 on a new hard drive. Now, I get an error message when I try to load Photoshop 64-bit. Dynamic Link Manager has stopped working.
I applied the DLM update, applied all the updated to all the programs in cs6, and still getting the DLM error message.
HELP!
Michele Johnson
423-619-9886

Tech support was finally able to correct the problem. He went into the appdata folder and renamed the dynamic link manager file. Then he restarted Photoshop, which then automatically recreated the file. Such a simple solution.

Dynamic link manager has stopped working

I downloaded and installed photshop CS6, supposedly succesfully, but when I try to run the application I get repeated msgs that dynamic link manager has stopped working. There was also a msg that the application has failed to start because MSVCP100.dll was not found. Both photoshop and bridge appear to work to the extent that I can browse and open files. However I am repeatedly interrupted with msg telling me the dynamic link manager has stopped working. Suggestions?

http://forums.adobe.com/message/4471627

Dynamic interface: dynamic AP management + NAT enabled

Similar Messages

Maybe you are looking for