EASY VPN hardware client not working.
Hello,
I'm experiencing an issue. I have the following topology:
192.168.12.0 /24 --- inside192.168.12.1(ASA5502)192.168.1.71 dhcp ---192.168.1.254 ISP GATEWAY ===201.144.194.226 PEER --Inside 192.168.0.0
I have VPNCLIENT configured correctly but can't seem to pass traffic or get the tunnel up. I'm attaching debug crypto isakmp 10, debug crypto ipsec 10, logging debug messages. Also find the config attached.
I'm trying to reach from 192.168.12.10 to a server 192.168.1.200 on remote.
Running version 8.2(5)
Any idea of what i have configured wrong?
Thanks
Tony
Couple of quick comments:
1. I do not see 192.168.0.0 part of that inside_outbound_nat0_acl ACL.
2. I see a crypto map instance 40 with "incomplete" crypto map, which is actually missing a match address.
crypto map outside_map 40 ipsec-isakmp
crypto map outside_map 40 set peer 216.27.161.109
crypto map outside_map 40 set transform-set ESP-DES-MD5
! Incomplete
Not sure if this is the current configuration from the pix. If there is a crypto map instance with a incomplete match address, all traffic will be encrypted.
Regards,
Arul
Similar Messages
-
I have just upgraded to Lion and now my VPN connection does not work properly. It was working fine when I was using Leopard. The VPN is My Private Network and we use it to link to BBC iPlayer when abroad. It will actually connect to the VPN site and shows a UK IP address, but then when we try to load an iPlayer programme we get the message from the BBC that we are not in the country and, therefore, cannot access the site. Any suggestions?
Have a look at System Preferences, Accessibility, VoiceOver.
(Command - F5).
charlie -
How can apple send out an os update that renders an important function of the software/hardware to not work? They knowingly have sent out this new os update for iPad which makes airplay nonfunctining! I need this for my business! I could understand if they didn't know, but it is all over the Internet! When I went in to have it revert back to os6 (which worked fine!) I was actually asked if I had done any research before I installed the upgrade! As if this is the consumer's fault for being dumb enough to fall for the upgrade!
That is not what I have discovered, nor what others have discovered, nor what I was told when I went the Genius Bar. I cannot remotely mirror to my MacBook Pro and it only started the day after I installed the upgrade. We tested it with an iPad that had not been upgraded, no problem.
-
I have a very strange problem.
I need to connect to my work via the cisco vpn client (version 5.0.00.0340).
My previous laptop (T43 , windows XP) worked well through both wired / wireless connections. My desktop machine (vista) works via wired connection (it has no wireless connection).
On my new T400, the VPN client works via a wired connection but not via the wireless adapter.
On the wireless apapter, the vpn seems to connect OK, but when I try to access resources via the VPN there is little response.
I get this in the vpn log...
405 08:56:57.073 04/16/09 Sev=Warning/2 IPSEC/0xE3700003
Function CniInjectSend() failed with an error code of 0xa4510009 (IPSecDrvCB:846)
I've tried disabling the firewall (in both the T400 and the router), removed access connections, and disabling tcp v6. I've rebooted everything too.
But, nothing seems to work. I suspect the problem is on the t400 somewhere, because the old laptop used to work OK via wireless.
I've seen some google links on cisco vpn not working via wireless but nothing seems to apply to my exact situation yet.
Anyone else had this problem or know of a fix? Thanks in advance.
Solved!
Go to Solution.all good now, got it working.
The Deterministic network thing was not installed on the wireless adapter for some reason.
So, I installed the latest wireless driver, reinstalled the vpn and all is good now. -
Zone Base Forewall for VPN connections does not work after IOS upgrade
Hi all,
We use cisco router 2911 as corporate gateway - there is Zone Based Firewall implemented - I upgraded IOS to last version (15.2(2)T1) - originaly version 15.1(4)M1 - to solve issue with Anyconnect connections (bug CSCtx38806) but I found that after upgrade the VPN users are not able to communicate with sources in other zones.
More specific
WebVPN use this virtual template interface
interface Virtual-Template100
description Template for SSLVPN
ip unnumbered GigabitEthernet0/1.100
zone-member security INSIDE
There are other zones VOICE, LAB, ...
In the policy any connection is allowed (used inspection of icmp, tcp and udp) from INSIDE zone to VOICE or LAB zone
After VPN connection I am able to reach resources in INSIDE zone (which is the most important), but not in other zones. Before upgrade it worked.
Once I changed zone in Virtual-Template interface to VOICE, I was able to reach sources in VOICE zone but not in any other. I searched more and found the stateful firewall is not working for connections from VPN as ping is blocked by policy on returning way - it means by policy VOICE->INSIDE, once I allowed communication from "destination" zone to INSIDE zone - the connections started to work, but of cause it is not something I want to setup.
Does anybody has the same experiance?
Regards
PavelIt seems to me I should add one importatant note - if client is connected directly in INSIDE zone, he can reach resources in other zones without any issue - so the problem is only when the client is connected by VPN - not in ZBF policy setup.
Pavel -
RDP over Easy VPN Server fails, ping works
Dear experts,
What can I do to troubleshout this problem?
This is our router configuration with the Easy VPN Server enabled:
version 15.1
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
no service dhcp
hostname ####
boot-start-marker
boot-end-marker
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 51200
logging console critical
enable secret ###########################
aaa new-model
aaa authentication login local_authen local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authorization exec local_author local
aaa authorization network ciscocp_vpn_group_ml_1 local
aaa session-id common
no ipv6 cef
no ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.29
ip dhcp excluded-address 192.168.1.59
ip dhcp excluded-address 192.168.1.99
ip dhcp excluded-address 192.168.1.182
ip dhcp excluded-address 192.168.1.192
ip dhcp excluded-address 192.168.1.193
ip dhcp excluded-address 192.168.1.198
ip dhcp excluded-address 192.168.1.238
ip dhcp excluded-address 192.168.1.240
ip dhcp excluded-address 192.168.1.243
ip dhcp excluded-address 192.168.1.245
ip dhcp excluded-address 192.168.1.215
ip dhcp excluded-address 192.168.1.122
ip dhcp excluded-address 192.168.1.33
ip dhcp excluded-address 192.168.1.10
ip dhcp excluded-address 192.168.1.11
ip dhcp excluded-address 192.168.1.201
no ip bootp server
ip dhcp-server ##########
multilink bundle-name authenticated
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-############
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-############
revocation-check none
crypto pki certificate chain TP-self-signed-############
certificate self-signed 01
quit
license udi pid CISCO1941/K9 sn ##########
license boot module c1900 technology-package securityk9
license boot module c1900 technology-package datak9
username #### privilege 15 secret ####################.
username #### secret ####################
username #### secret ####################
username #### secret ####################
redundancy
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
crypto ctcp port 10000
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group ###########
key ##########
dns 192.168.1.4 192.168.1.6
domain ####.local
pool SDM_POOL_1
acl 102
include-local-lan
crypto isakmp profile ciscocp-ike-profile-1
match identity group ##############
client authentication list ciscocp_vpn_xauth_ml_1
isakmp authorization list ciscocp_vpn_group_ml_1
client configuration address respond
virtual-template 1
crypto ipsec transform-set ########### esp-aes 256 esp-sha-hmac
crypto ipsec profile CiscoCP_Profile1
set transform-set ###########
set isakmp-profile ciscocp-ike-profile-1
interface Null0
no ip unreachables
interface GigabitEthernet0/0
description $ETH-SW-LAUNCH$$INTF-INFO-GE 0/0$$ES_LAN$$ETH-LAN$$FW_INSIDE$
ip address 192.168.1.1 255.255.255.0
ip access-group 101 in
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
no mop enabled
interface GigabitEthernet0/1
description $FW_OUTSIDE$
ip address dhcp
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat outside
ip nat enable
ip virtual-reassembly in
duplex auto
speed auto
no mop enabled
interface Virtual-Template1 type tunnel
ip unnumbered GigabitEthernet0/0
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
ip local pool SDM_POOL_1 192.168.2.1 192.168.2.10
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 23 interface GigabitEthernet0/1 overload
ip route 0.0.0.0 0.0.0.0 ###########
logging esm config
logging trap debugging
access-list 23 permit 192.168.1.0 0.0.0.255
access-list 23 permit 192.168.2.0 0.0.0.255
access-list 101 deny ip any host 184.82.162.163
access-list 101 deny ip any host 184.22.103.202
access-list 101 deny ip any host 76.191.104.39
access-list 101 permit ip any any
access-list 102 permit tcp any any eq 3389
access-list 102 permit ip any any
access-list 102 permit icmp any any
access-list 700 permit 000d.6066.0d02 0000.0000.0000
no cdp run
snmp-server group ICT v3 priv
control-plane
banner exec ^C
Welcome ####^C
banner login ^C
Unauthorized access prohibited
##################################^C
line con 0
login authentication local_authen
transport output telnet
line aux 0
login authentication local_authen
transport output telnet
line vty 0 4
access-class 23 in
password 7 ##################
authorization exec local_author
login authentication local_authen
transport input telnet ssh
line vty 5 15
access-class 23 in
authorization exec local_author
login authentication local_authen
transport input telnet ssh
scheduler allocate 20000 1000
endIn the server debug, I see this:
*Oct 13 09:25:46.662: ISAKMP:(2013): retransmitting phase 2 CONF_XAUTH -2020890165 ...
*Oct 13 09:25:46.662: ISAKMP (2013): incrementing error counter on node, attempt 1 of 5: retransmit phase 2
*Oct 13 09:25:46.662: ISAKMP (2013): incrementing error counter on sa, attempt 1 of 5: retransmit phase 2
*Oct 13 09:25:46.662: ISAKMP:(2013): retransmitting phase 2 -2020890165 CONF_XAUTH
*Oct 13 09:25:46.662: ISAKMP:(2013): sending packet to 109.59.232.39 my_port 500 peer_port 500 (R) CONF_XAUTH
*Oct 13 09:25:46.662: ISAKMP:(2013):Sending an IKE IPv4 Packet.
*Oct 13 09:25:49.850: ISAKMP (2013): received packet from 109.59.232.39 dport 500 sport 500 Global (R) CONF_XAUTH
*Oct 13 09:25:49.850: ISAKMP:(2013):processing transaction payload from 109.59.232.39. message ID = -2020890165
*Oct 13 09:25:49.850: ISAKMP: Config payload REPLY
*Oct 13 09:25:49.850: ISAKMP/xauth: reply attribute XAUTH_USER_NAME_V2
*Oct 13 09:25:49.850: ISAKMP/xauth: reply attribute XAUTH_USER_PASSWORD_V2
*Oct 13 09:25:49.850: ISAKMP/xauth: Expected attribute XAUTH_TYPE_V2 not received
*Oct 13 09:25:49.850: ISAKMP:(2013):peer does not do paranoid keepalives.
Is it something with the above line ?
/Jesper -
RV082 - SRP527W - VPN behind NAT not working
Hello,
I've really strange behaviors with my routers. We managed to get things running but once a week, the VPN link is down.
The connection is not restart, both routers shows "connected" but are not, and we had to click on "disconnect" to get the link back.
That was before an update in our infrastructure. Now, both routers are behind routers, so both NAT.
Now, the connection works for some time, but once a week, the link disconnected but i'm unable to get it back ! NOTHING works.
Last time, i spent 2Hours to configure the link again, setting the same parameters almost 10 time, and suddenly by magic, the 11st time it worked again. I read many people have troubles with RVXXX firmware so i don't know what to think.
Anyway, my BIG concern now, is that the link is down again, and it has been 6hours since we can't got it back. I restarted the routers many times, i've made some changes in the configuration, but if it worked, why should i modify it ?????? Why is it not working anymore ?
The log for the RV082 is almost empty about the link. Here's a snippet :
Feb 10 19:01:52 2014
VPN Log
(g2gips0) #8: initiating Main Mode
Feb 10 19:01:52 2014
VPN Log
(g2gips0) #8: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
Feb 10 19:01:52 2014
VPN Log
(g2gips0) #8: [Tunnel Negotiation Info] >>> Initiator Send Main Mode 1st packet
Feb 10 19:01:52 2014
System Log
gateway_to_gateway.htm is changed.
Feb 10 19:09:08 2014
VPN Log
(g2gips0): deleting connection
Feb 10 19:09:08 2014
VPN Log
(g2gips0) #8: deleting state (STATE_MAIN_I1)
Feb 10 19:09:08 2014
VPN Log
added connection description (g2gips0)
Feb 10 19:09:08 2014
VPN Log
listening for IKE messages
Feb 10 19:09:08 2014
VPN Log
forgetting secrets
Feb 10 19:09:08 2014
VPN Log
loading secrets from '/etc/ipsec.d/ipsec.secrets'
Feb 10 19:09:09 2014
System Log
gateway_to_gateway.htm is changed.
The log for the SRP527W is full of this :
Dump pluto log message in syslog : cat /var/log/messages |grep plutoJan 1 02:29:39 TLSR0254 authpriv.warn pluto[1156]: "G2" #187: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1Jan 1 02:29:39 TLSR0254 authpriv.warn pluto[1156]: "G2" #187: STATE_MAIN_R1: sent MR1, expecting MI2Jan 1 02:30:09 TLSR0254 authpriv.warn pluto[1156]: "G2" #186: max number of retransmissions (2) reached STATE_MAIN_R1Jan 1 02:30:19 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [RFC 3947] method set to=109 Jan 1 02:30:19 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 109Jan 1 02:30:19 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 109Jan 1 02:30:19 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]Jan 1 02:30:19 TLSR0254 authpriv.warn pluto[1156]: "G2" #188: responding to Main ModeJan 1 02:30:19 TLSR0254 authpriv.warn pluto[1156]: "G2" #188: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1Jan 1 02:30:19 TLSR0254 authpriv.warn pluto[1156]: "G2" #188: STATE_MAIN_R1: sent MR1, expecting MI2Jan 1 02:30:25 TLSR0254 authpriv.warn pluto[1156]: pending Quick Mode with 37.1.XXX.XXX "G2" took too long -- replacing phase 1Jan 1 02:30:25 TLSR0254 authpriv.warn pluto[1156]: "G2" #189: initiating Main Mode to replace #185Jan 1 02:30:49 TLSR0254 authpriv.warn pluto[1156]: "G2" #187: max number of retransmissions (2) reached STATE_MAIN_R1Jan 1 02:30:59 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [RFC 3947] method set to=109 Jan 1 02:30:59 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 109Jan 1 02:30:59 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 109Jan 1 02:30:59 TLSR0254 authpriv.warn pluto[1156]: packet from 37.1.XXX.XXX:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]Jan 1 02:30:59 TLSR0254 authpriv.warn pluto[1156]: "G2" #190: responding to Main Mode
Please help me to get things sorted. I just don't understand why nothing is written in the log about the SRP trying to make a connection. I also don't understand why suddenly the link is broken, and without changing anything, it can't get it back normally !!
Best RegardsHi again,
Samir, i rebooted all the routers dozens of time when that happened, and it doesn't changed anything. Anyway, i called the Cisco Hotline. They could connect by VPN to RV082, but not the SRP, they didn't know why. Hardware or software failure.
Anyway, i bought another router.
Now i would like to use the SRP527W as a WIFI hotspot only. It doesn't work.
My settings are :
- Router defined as BRIDGE only (using Port lan 4 as Ethernet WAN)
- WAN Interface is assigned 192.168.0.246 / 24
- Gateway for the WAN interface is 192.168.0.254
- Ethernet cable is plugged from LAN4/WAN to my new Modem/Router on LAN3.
- Port LAN2 of SRP527W is defined with VLAN IP Address 192.168.15.254.
When connected to the SRP527W on LAN2, from my computer (192.168.15.200), i can't ping 192.168.0.246 neither 0.254 (gateway is set to 15.254)
Still, when connected to the SRP527W and with the Ping Dagnosis interface, pinging "192.168.0.254" shows "timed out".
I tried almost every configuration, none worked.
Please note that when connected from my computer directly to my new modem/router on port LAN3, with IP Address 192.168.0.200, i can access internet and ping everything. When set as DHCP too, i can grab an IP Address from my DHCP Windows Server.
So, why is the SRP527W unable to work in this configuration ? it seems nothing pass through WAN port.
If i'm right, there is only the WAN port that should be plugged to my modem router. With this settings, SSID should go directly to Internet, and for the other SSID, my LAN (through the modem/router). However, it doesn't work.
Could you help me please ? Thank you -
Client not working after upgrade
Hi,
I am upgrading my SAP 8.8 SP:00 Pl 10 to PL 16. with the help of upgrade wizard all the SAP items are upgraded from PL 10 to Pl 16.
When i was login in through SAP client it asked for upgrade i clicked yes after some time the upgrade stop and the SAP client logo on the server disappear. Now i am not able to login since there is no client to login.
I tried to install client from set up file but it gives following error
Error Number: 0x80040702
Description: Failed to load Dll: creator Dll
I have refered SAP Note: 1408662 and also refered other thread but its not working
I tried to uninstall client from add/ remove program but i am not able to do so
Pls provide solution since i am not able to login.Hi,
I have already installed the recommended c++ version as per SAP note, still it is not working. I tried to uninstall the client from
B1SHR folder but it gives me error.
The server is properly upgraded and problem exists on 3 of client machines.
I have to any how remove this client file or make it working to acces SAP else i wil have to format system which i dont want to do. -
Macbook dies after 2008-005 security update: even hardware test not working
My Macbook no longer boots after installing security update 2008-005. Behaves as if HD is dead, AND as if boots from SuperDrive are broken too.
Sequence of events:
1. 10.5.4, Software Update notifies me of update.
2. I permit it. Immediately requires a reboot.
3. Go away for several hours.
4. Upon return, I notice the Leopard outer-space background.
5. Spinning beachball when I move the mouse.
6. Go away for several minutes.
7. Return. No change. Power down computer.
OK ... by now, you may be saying that it might still have been updating and I shouldn't have interrupted it.
But since then, the machine behaves not only like the disk is dead, but I can't even get a hardware test to run from DVD.
So, to continue.
8. Start machine again. Apple boot sound. Nothing on screen.
9. After a while, flashing "folder" icon with question mark.
Since then I've attempted to boot in safe mode, verbose mode, FireWire target disk mode (against a 10.4.x box), boot from original install disk, boot into hardware test mode from original install disk. None of these things worked. I've reset the PRAM.
The only diagnostic activity of all of these that has produced any different feedback is the PRAM reset (which sounded the Apple boot sound a second time). Everything else does not work. If the HD was dead, I could understand that none of the attempts to boot into FireWire target disk mode, or to boot from DVD and then expect to see the HD mount in some way, would work. But since it doesn't even boot the hardware test from the DVD, I'm really baffled. Any ideas? Thanks.Well, my solution was to buy DiskWarrior and copy what I could (which was a lot, thankfully) to a FireWire external disk, then reinstall. DiskWarrior reports S.M.A.R.T. status OK, so I've gone with a fresh partition in Disk Utility and successfully installed 10.4 from the original DVDs.
Have also run Apple Hardware Test and had no problems, so I've decided to trust the drive in the short term.
Unfortunately, now, 10.5 upgrade disks won't finish and guess what ... a partial install of 10.5 breaks the 10.4! So, the machine has a recognizable startup disk but justs sits in a loop rebooting itself, presumably as it hits some inter-10.4/10.5 state and gives up.
Next up I tried to restore my 10.5 from a wired ethernet connection to my Time Capsule. Having never once been able to browse my backups in Time Machine under 10.5, I was somewhat surprised to find that the 10.5 Installer was happy to let me try a restore from the Time Capsule. It crunched away until it was happy that I had enough space on my new partition, and then did what seemed a pretty instantaneous restore. The Macbook reboots and ... can't see the startup disk.
Maybe my disk really is on the way out. -
I have the Easy System Cleaner. It worked through Internet Explorer. But when it comes to Mozilla Foxfire. It stops.
The message is:
error executing sql. Error 26. File opened that is not a database file "select[sql] from sqlite_master where [type]="table' and lower (name)='mos_cookies' " File is encrypted or is not a database.
What should I do. And where do I look to solve this problem.
I need to use my Easy System Cleaner...I paid for it!
[email protected]How do I fix this error
-
DCNM LAN JAVA Client Not working
Hi ,
Recently i installed the DCNM server , we are using nexus 7k in dc environment . I purchased the DCNM server license and assigned it to switches thourgh web dcnm client . Login in Java DCNM LAN is not working , It says check your username/password . Only with SAN its working Fine , Authetication to the dcnm is configured to check the TACACS server . Can you help on this.
Thanks , Vedagiri GopinathDuplicate posts. :P
Go here: http://supportforums.cisco.com/discussion/12164196/dcnm-lan-java-client-not-working -
Oracle 10g Client not working from Vista Business
Hi,
I have installed Oracle 10g Rel2 DB on my desktop (OS Vista Ultimate X64 bit) and try to connect from my new laptop (OS Vista business) after installing the client software which does not work, whereas I am able to connect to same database from my other laptop using Windows XP. The tnsnames.ora files on both laptops have the same contents. Moreover, the SQL Plus is also not working on the vista laptop, I mean when I try to login the window closes down itself it doesn't stay open even to give any error message. . . Any ideas would be a great help . . .thxDid you install the Vista specific Oracle client?
http://www.oracle.com/technology/software/products/database/oracle10g/htdocs/10204_winx64_vista_win2k8.html -
Hardware buffering not working on Win XP Pro
Card: Audigy 2 Platinum with latest drivers (02.09.006)
Latest DirectX 9.0c (directx_dec2006_redist.exe)
DxDiag DirectSound test passes ok, except that at the end gives:
"Your card does not support hardware buffering. Sounds will only play back from software buffers."
Tested on Win XP Pro SP2, hardware buffering worked ok.
Solution?
Thanks,
Gustavs
Sound Devices
Description: SB Audigy 2 Audio [D880]
Default Sound Playback: Yes
Default Voice Playback: Yes
Hardware ID: PCI\VEN_02&DEV_0004&SUBSYS_00202&REV_04
Manufacturer ID:
Product ID: 00
Type: WDM
Driver Name: ctaud2k.sys
Driver Version: 5.2.000.96 (English)
Driver Attributes: Final Retail
WHQL Logo'd: n/a
Date and Size: 8//2006 5:24:22, 853376 bytes
Other Files:
Driver Provider: Creative
HW Accel Level: Full
Cap Flags: 0xF5F
Min/Max Sample Rate: 00, 200000
Static/Strm HW Mix Bufs: 0, 0
Static/Strm HW 3D Bufs: 0, 0
HW Memory: 0
Voice Management: No
EAX(tm) 2.0 Listen/Src: No, No
I3DL2(tm) Listen/Src: No, No
Sensaura(tm) ZoomFX(tm): No
Registry: OK
Sound Test Result: All tests were successful.Just found that the problem is probably something with RAM configuration (motherboard problem).
I have 4GB RAM, with Memory Hole disabled in bios it works ok, but then only shows ~2.2GB. I only get 2GB in Win XP Pro SP2 with Memory Hole enabled (x64 is ok, 4GB). I think this option is not working properly.
Gustavs -
Cs4 - hardware rendering not working
The checkbox is LOCKED and set to software render by default!
I have updated to Bridge CS4 and now the slideshow and dinamic zoom are not working smoothly as on CS3.
How can I set the checkbox to Hardware?
Thanks,
Z
Graphic Card = Intel GMA 500 (latest drivers)
Bridge cs3 accepts render by hardware and it works smoothly!Ok, here is some detail info of the issue:
On my netbook: CPU=1.6ghz, RAM=2Gb, VGA=Intel500, SSD@60mb/s
- Bridge cs3 = Hardware Render = impressive response time. [way beyond 30fps]
- Bridge cs3 = Software Render = <10fps
- Bridge cs4 = Hardware Render = not available
- Bridge cs4 = Software Render = 2 or maybe 3fps (!!!) Its a huge diference!
Come on Adobe, a loot of computers are/will be shipping this graphic card!
Just release a patch for us. Or think about it on cs5.
Z -
Driver to email client not working
For my class we are attempting to write our own email client. Our professor gave us the following driver. However when I attempt to compile the driver I get these errors:
MailClient.java:125: cannot find symbol
symbol : variable envelope
location: class MailClient.SendListener
SMTPConnection connection = new SMTPConnection(envelope);
^
MailClient.java:126: cannot find symbol
symbol : variable envelope
location: class MailClient.SendListener
connection.send(envelope);Admittedly it could be something with the SMPTConnection code, as that is what we had to write. However I would have expected it to throw some sort of exception in there and it does not. Any help to figure out why the driver is not working would be appreciatted.
Code:
import java.io.*;
import java.net.*;
import java.awt.*;
import java.awt.event.*;
/* $Id: MailClient.java,v 1.7 1999/07/22 12:07:30 kangasha Exp $ */
* A simple mail client with a GUI for sending mail.
* @author Jussi Kangasharju
public class MailClient extends Frame {
/* The stuff for the GUI. */
private Button btSend = new Button("Send");
private Button btClear = new Button("Clear");
private Button btQuit = new Button("Quit");
private Label serverLabel = new Label("Local mailserver:");
private TextField serverField = new TextField("", 40);
private Label fromLabel = new Label("From:");
private TextField fromField = new TextField("", 40);
private Label toLabel = new Label("To:");
private TextField toField = new TextField("", 40);
private Label subjectLabel = new Label("Subject:");
private TextField subjectField = new TextField("", 40);
private Label messageLabel = new Label("Message:");
private TextArea messageText = new TextArea(10, 40);
* Create a new MailClient window with fields for entering all
* the relevant information (From, To, Subject, and message).
public MailClient() {
super("Java Mailclient");
/* Create panels for holding the fields. To make it look nice,
create an extra panel for holding all the child panels. */
Panel serverPanel = new Panel(new BorderLayout());
Panel fromPanel = new Panel(new BorderLayout());
Panel toPanel = new Panel(new BorderLayout());
Panel subjectPanel = new Panel(new BorderLayout());
Panel messagePanel = new Panel(new BorderLayout());
serverPanel.add(serverLabel, BorderLayout.WEST);
serverPanel.add(serverField, BorderLayout.CENTER);
fromPanel.add(fromLabel, BorderLayout.WEST);
fromPanel.add(fromField, BorderLayout.CENTER);
toPanel.add(toLabel, BorderLayout.WEST);
toPanel.add(toField, BorderLayout.CENTER);
subjectPanel.add(subjectLabel, BorderLayout.WEST);
subjectPanel.add(subjectField, BorderLayout.CENTER);
messagePanel.add(messageLabel, BorderLayout.NORTH);
messagePanel.add(messageText, BorderLayout.CENTER);
Panel fieldPanel = new Panel(new GridLayout(0, 1));
fieldPanel.add(serverPanel);
fieldPanel.add(fromPanel);
fieldPanel.add(toPanel);
fieldPanel.add(subjectPanel);
/* Create a panel for the buttons and add listeners to the
buttons. */
Panel buttonPanel = new Panel(new GridLayout(1, 0));
btSend.addActionListener(new SendListener());
btClear.addActionListener(new ClearListener());
btQuit.addActionListener(new QuitListener());
buttonPanel.add(btSend);
buttonPanel.add(btClear);
buttonPanel.add(btQuit);
/* Add, pack, and show. */
add(fieldPanel, BorderLayout.NORTH);
add(messagePanel, BorderLayout.CENTER);
add(buttonPanel, BorderLayout.SOUTH);
pack();
show();
static public void main(String argv[]) {
new MailClient();
/* Handler for the Send-button. */
class SendListener implements ActionListener {
public void actionPerformed(ActionEvent event) {
System.out.println("Sending mail");
/* Check that we have the local mailserver */
if ((serverField.getText()).equals("")) {
System.out.println("Need name of local mailserver!");
return;
/* Check that we have the sender and recipient. */
if((fromField.getText()).equals("")) {
System.out.println("Need sender!");
return;
if((toField.getText()).equals("")) {
System.out.println("Need recipient!");
return;
/* Create the message */
Message mailMessage = new Message(fromField.getText(),
toField.getText(),
subjectField.getText(),
messageText.getText());
/* Check that the message is valid, i.e., sender and
recipient addresses look ok. */
if(!mailMessage.isValid()) {
return;
/* Create the envelope, open the connection and try to send
the message. */
try {
Envelope envelope = new Envelope(mailMessage, serverField.getText());
catch (UnknownHostException e) {
/* If there is an error, do not go further */
return;
try {
SMTPConnection connection = new SMTPConnection(envelope);
connection.send(envelope);
connection.close();
catch (IOException error) {
System.out.println("Sending failed: " + error);
return;
System.out.println("Mail sent succesfully!");
/* Clear the fields on the GUI. */
class ClearListener implements ActionListener {
public void actionPerformed(ActionEvent e) {
System.out.println("Clearing fields");
fromField.setText("");
toField.setText("");
subjectField.setText("");
messageText.setText("");
/* Quit. */
class QuitListener implements ActionListener {
public void actionPerformed(ActionEvent e) {
System.exit(0);
}This is what I mean:
/* Create the envelope, open the connection and try to send the message. */
Envelope envelope = null;
try {
envelope = new Envelope(mailMessage, serverField.getText());
catch (UnknownHostException e) {
/* If there is an error, do not go further */
return;
try {
SMTPConnection connection = new SMTPConnection(envelope);
connection.send(envelope);
connection.close();
catch (IOException error) {
System.out.println("Sending failed: " + error);
return;
System.out.println("Mail sent succesfully!");
Maybe you are looking for
-
I've been trying to install recent updates for numbers, pages, and keynote, I get a message that says "There was an error in the App store. Please try again later." (20). I tried several times over the last few days and continue to get the same erro
-
What is the ideal size and resolution of a photo for display on the iPad?
I'm finding no info on the size of a photo for the best possible display on the iPad. The screen is obviously much larger than iPod Touch or iPhone; photos sized for them are fuzzy on the iPad. Ideally, a photo should be sized for the exact number
-
Bad sound when connecting iPod to stereo
Can anyone help with this one? I am trying to connect my iPod to my stereo receiver. I have the 5th generation 30gb iPod. I hooked it up to my stereo (Sony str-de825) with a monster cable through the tape & video inputs and it it sounded low and mudd
-
Nokia N-80 (v 4.0707.0.7 -- 28.3.2007)
Has updated N80 up to last insertion (4,07,07,0,7) function USSD has ceased to work!!!! How to roll away an insertion back on the old version? EDIT: Removed non-English content and contact details.Message Edited by mercurius on 04-Jun-2007 04:55 PM
-
Bookmarks> Organize bookmarks> ★ Export HTML > "export bookmarks file" window appears. Save as "Bookmarks.HTML" Desktop> NO FILE IS PRODUCED!