Error -2147418113 while initialize CI 4500Ls AC Power Source

I've been trying to get LabVIEW to work with CI 4500Ls. I installed the driver, and tried to run it. I got error -2147418113 "Catastrophic failure" while initializing. Does anyone have any idea what's going on?
I've googled, and got different answers for different situations, so I'm really confused. I'm relatively new to LabVIEW.

What is CI?
MAX is Measurement and Automation Explorer. It is on your desktop and it is a utility program installed with NI hardware drivers such as NI-VISA. If the serial converter is correctly installed, you will see a com port listed under Hardware.
Putty not working is a bad sign, assuming you sent the correct command. If you did, check the status of the serial port driver in Windows device manager. At this point, it does not sound like a problem with any NI hardware or software.

Similar Messages

  • 407 proxy error occured while checking certificate revocation

    Hello,
    A 407 proxy auth error occured while checking the server certificate revocation.
    source code:
      var loader:URLLoader = new URLLoader();
      loader.load(new URLRequest("https://www.example.com/"));
    It works fine on Windows XP you know, but does not work on Vista and Win7
    under proxy authentication environment such as my office.
    Vista and Win7 were sending and receiving the following packets:
      1) client to squid: CONNECT www.example.com:443 HTTP/1.0
      2) squid to client: HTTP/1.0 200
      3) client to squid: Client Hello
      4) squid to client: Server Hello, Change Cipher Spec, Encrypted Handshake Message
      5) client to squid: Change Cipher Spec, Encrypted Handshake Message
      6) client to squid: GET http://ocsp.verisign.com/0123456789abcdef...
      7) squid to client: HTTP/1.0 407 Proxy Authentication Required
      8) client to squid: GET http://crl.verisign.com/foo.crl HTTP/1.1
      9) squid to client: HTTP/1.0 407 Proxy Authentication Required
    at 7), HTTP 407 error occured, but it is a correct response
    because the HTTP request at 6) does not have a Proxy-Authorization header.
    It seems that the request of 6) was sent by CryptoAPI.
    The only way to avoid this problem is that turn off the checkbox
    "Check for server certificate revocation*" in Internet Option of Internet Explorer.
    This problem occured in both AIR 1.5.3 and 2.0b.
    Does anyone have a similar problem ?

    What you have discovered is the reason to *not* use LDAP URLs for CDP and AIA extensions in your PKI. To access those URLs, the account must access to the URLs. In your output, it is quite clear that the local account does not have necessary permissions
    (you also use FILE URLs for publication, which again is not recommended).
    The best practice is to use a single URL for the CDP extension. It should be an HTTP URL that is hosted on a highly available (internally and externally accessible) Web cluster.
    For the AIA extension, it should contain two URLs: one for the CA certificate - again to an internally and externally accessible, highly available Web cluster and one for the OCSP service - also
    an internally and externally accessible, highly available Web cluster.
    the other issue is that the root CA is *not* trusted when run by a non-domain account. How are you adding the trusted root CA. It is recommended to do this by running
    certutil -dspublish -f RootCA.crt.
    This will ensure that the computer account trusts the root CA. In your output, the root CA certificate is not trusted.
    Brian

  • RC-00110: Fatal: Error occurred while relinking of ApplyDBTechStack

    Hi Experts,
    I am performing Cloning for Oracle Application R12 with rapid clone and adcfgclone dbTier is failing with the below error.
    RC-00110: Fatal: Error occurred while relinking of ApplyDBTechStack
    Both my source and target system are on the same server. I am using dbTier option because I have cold backup available from the source system.
    DB Version: 11.2.0.3
    EBS version: 12.1.3
    OS Version: RHEL6, 64 bit
    cat /data/db_top/db/tech_st/11.2.0/appsutil/log/TEST_oracleupk/ApplyDBTier_07050816.log
    Log file contents:-
      AutoConfig could not successfully execute the following scripts:
        Directory: /data/db_top/db/tech_st/11.2.0/perl/bin/perl -I /data/db_top/db/tech_st/11.2.0/perl/lib/5.8.3 -I /data/db_top/db/tech_st/11.2.0/perl/lib/site_perl/5.8.3 -I /data/db_top/db/tech_st/11.2.0/appsutil/perl /data/db_top/db/tech_st/11.2.0/appsutil/clone
          ouicli.pl               INSTE8_APPLY       255
    AutoConfig is exiting with status 1
    RC-50013: Fatal: Instantiate driver did not complete successfully.
    /data/db_top/db/tech_st/11.2.0/appsutil/driver/regclone.drv
    cat $[target_oracle_home]/ appsutil/ log/$CONTEXT_NAME/make_[timeStamp].log
    Error found while relinking
      return code = .58
    I have already checked these MOS Notes
    OUICLI.PL Fails While Running Adcfgclone On Oracle EBS R12 If Global Inventory Does Not Exist [ID 458653.1]
    RC-00110 Error While Running adlnkoh.sh [ID 330469.1]
    But none has worked in my case. Please let me know what I'm missing here.
    Thanks,
    Ankur

    Hi Hussein,
    Following the workaround provided in this MOS Note ID has solved my issue.
    Rapid Clone On Dbtier Fails "RC-50013: Fatal: Instantiate Driver Did Not Complete Successfully" [ID 1352116.1]
    But now "adcfgclone.pl appsTier"  is failing with the below error.
    [AutoConfig Error Report]
    The following report lists errors AutoConfig encountered during each
    phase of its execution.  Errors are grouped by directory and phase.
    The report format is:
          <filename>  <phase>  <return code where appropriate>
      [SETUP PHASE]
      AutoConfig could not successfully execute the following scripts:
        Directory: /data/appl_top/inst/apps/TEST_oracleupk/admin/install
          adgendbc.sh             INSTE8_SETUP       1
          afcpnode.sh             INSTE8_SETUP       1
          afgcsreg.sh             INSTE8_SETUP       1
          txkWfClone.sh           INSTALL_SETUP      1
      [PROFILE PHASE]
      AutoConfig could not successfully execute the following scripts:
        Directory: /data/appl_top/apps/tech_st/10.1.3/perl/bin/perl -I /data/appl_top/apps/tech_st/10.1.3/perl/lib/5.8.3 -I /data/appl_top/apps/tech_st/10.1.3/perl/lib/site_perl/5.8.3 -I /data/appl_top/apps/apps_st/appl/au/12.0.0/perl -I /data/appl_top/apps/tech_st/10.1.3/Apache/Apache/mod_perl/lib/site_perl/5.8.3/i686-linux-thread-multi /data/appl_top/inst/apps/TEST_oracleupk/admin/scripts/adexecsql.pl sqlfile=/data/appl_top/inst/apps/TEST_oracleupk/admin/install
          afwebprf.sql            INSTE8_PRF         1
          amscmprf.sql            INSTE8_PRF         1
          amswebprf.sql           INSTE8_PRF         1
          bisadmprf.sql           INSTE8_PRF         1
          bisdblrp.sql            INSTE8_PRF         1
          clnadmprf.sql           INSTE8_PRF         1
          cncmprf.sql             INSTE8_PRF         1
          cseadmprf.sql           INSTE8_PRF         1
          csfadmprf.sql           INSTE8_PRF         1
    csiadmprf.sql     
    INSTE8_PRF   
    1
    eamadmprf.sql     
    INSTE8_PRF   
    1
    fteadmprf.sql     
    INSTE8_PRF   
    1
    icxwebprf.sql     
    INSTE8_PRF   
    1
    oksfrmprf.sql     
    INSTE8_PRF   
    1
    wshadmprf.sql     
    INSTE8_PRF   
    1
    Directory: /data/appl_top/inst/apps/TEST_oracleupk/admin/install
    adadmprf.sh       
    INSTE8_PRF   
    1
    admk80ln.sh       
    INSTALL_PRF  
    1
    afadmprf.sh       
    INSTE8_PRF   
    1
    afcpctx.sh        
    INSTE8_PRF   
    1
    afcpgsm.sh        
    INSTE8_PRF   
    1
    ibywebprf.sh      
    INSTE8_PRF   
    1
    igccmprf.sh       
    INSTE8_PRF   
    1
    jtfictx.sh        
    INSTE8_PRF   
    1
    okladmprf.sh      
    INSTE8_PRF   
    1
    txkJavaMailerCfg.sh
    INSTE8_PRF   
    1
    txkWebServicescfg.sh
    INSTE8_PRF   
    1
      [APPLY PHASE]
      AutoConfig could not successfully execute the following scripts:
    Directory: /data/appl_top/apps/tech_st/10.1.3/perl/bin/perl -I /data/appl_top/apps/tech_st/10.1.3/perl/lib/5.8.3 -I /data/appl_top/apps/tech_st/10.1.3/perl/lib/site_perl/5.8.3 -I /data/appl_top/apps/apps_st/appl/au/12.0.0/perl -I /data/appl_top/apps/tech_st/10.1.3/Apache/Apache/mod_perl/lib/site_perl/5.8.3/i686-linux-thread-multi /data/appl_top/inst/apps/TEST_oracleupk/admin/install
    adadmat.pl        
    INSTE8_APPLY 
    1
    AutoConfig is exiting with status 31
    RC-50014: Fatal: Execution of AutoConfig was failed
    Raised by oracle.apps.ad.clone.ApplyApplTop
    ERROR: AutoConfig completed with errors. Check logfile at /data/appl_top/inst/apps/TEST_oracleupk/admin/log/ApplyAppsTier_07080320.log for details.
    ApplyApplTop Completed Successfully.
    # Checking the status of AutoConfig run of ApplyApplTop
    Warning : AutoConfig has completed with  errors .
    Thanks,
    Ankur

  • Error 8 while loading the data from the souce system

    Hi Gurus
    Every day we are loading some data from one of our souce systems through process chain
    But today all the loads failed complaining about error 8 while extacting the data
    connection to source system is fine
    we have the problem while loading master data from the same source system
    any solution?
    Thanks in advance

    Hi,
    Check with basis team regarding any patches applied in source system or not ? If yes then replicate all data sources and activate again.
    hope it helps...
    regards,
    Raju

  • "An error occured while working on the Data Model in the workbook" on some workbooks published to Power BI site

    Hello,
    I am using the Power BI for Office 365, and I have published several Excel 2013 workbooks having Power Pivot Data Models.
    I have a problem on some of the workbooks, once a slicer is selected, I get the error: "An error occurred while working on the Data Model in the workbook" and the slicers do not affect the charts.
    Some workbooks work perfectly fine. I am using the same user for all workbooks when creating and publishing. I tried with small workbooks less than < 10 MB size and larger workbooks > 10 MB. There is no rule, some workbooks larger than 10 MB work perfectly
    with the slicers effecting the charts, and some don't. Similarly for smaller size.
    Any ideas of how I can debug the cause of the issue? 
    Appreciate any feedback, 
    Thanks,
    Grace

    Hi Grace,
    I assume that the experience in the Excel client is working fine, right?
    Are you getting a correlation id with the error?
    Please send us a bit more information / samples to reproduce over email to
    this address.
    thanks,
    Guy
    GALROY

  • Error encountered while doing on-demand refresh of Power BI report

    When I try to manually refresh a PowerBI excel that has been uploaded on to SharePoint, I get this error.
    "OnPremise error: Sorry, you don't have permissions to retrieve data for this data connection. Request access from your Power BI admin. An error occurred while processing table 'Reference Data'. The current operation was cancelled because another
    operation in the transaction failed. "
    It has been verified to us that the data management gateway has been approved and we have made sure that the credentials and the database details to connect to the On-Prem instance are the same as specified.
    THe correlation ID is  8eb7c217-f62d-4137-a648-5df57937058e

    the error is talking about the permissions to the data source, in the PBI admin center, per data source you need to specify who (O365 user) can access it, maybe this is the source of your problem?
    GALROY

  • Could not initialize variable. An error occurs while initializing BPEL .

    I have the following error:
    **Could not initialize variable. An error occurs while initializing BPEL variable inputVariable; the schema processor cannot find the element {http://xmlns.oracle.com/MRTApplicationWorkflow/Project1/BPELProcess1}processRequest in the following schemas: oracle.fabric.common.wsdl.SchemaManager@e92e05. The XSD element on which the variable was based was not properly defined in XSD or the WSDL. Ensure that the element named in the error message is valid in the XSD or the WSDL.**
    My process input xsd below:
    <?xml version="1.0" encoding="UTF-8"?>
    <schema attributeFormDefault="unqualified"
         elementFormDefault="qualified"
         targetNamespace="http://xmlns.oracle.com/MRTApplicationWorkflow/Project1/BPELProcess1"
         xmlns="http://www.w3.org/2001/XMLSchema"
    xmlns:q1="http://schemas.datacontract.org/2004/07/WM.Services.MRTPortfolioService.BusinessObjects">
    <import schemaLocation="MRTWorkflowService.svc_xsd_xsd2.xsd"
    namespace="http://schemas.datacontract.org/2004/07/WM.Services.MRTPortfolioService.BusinessObjects"/>
    <element name="processRequest">
              <complexType>
                   <sequence>
                        <element name="institutionid" type="int" />
    <element name="brokerid" type="long"/>
    <element name="accountid" type="string"/>
                   </sequence>
              </complexType>
         </element>
         <element name="processResponse">
              <complexType>
                   <sequence>
                        <element name="result" type="q1:ArrayOfMRTProposedOrder"
    />
                   </sequence>
              </complexType>
         </element>
    </schema>
    Please help me with this isssue.
    I am using BPEL 2.0.

    Please check your XSD and dependant XSD's whether it contains any special characters.
    I solved the same issue in my BPEL process by commenting the special characters included in <documentation> element of XSD.

  • An error occurred while attempting to initialize the Borland Database Engine (error $2108)

    Hello:
    I have recently started getting this error when trying to Hot Sync my device:
    An error occurred while attempting to initialize the Borland Database Engine (error $2108)
    The device is a Symbol scanner with Palm OS v4.17.   It is connected to my computer with a serial cable.  The only relatively recent changes I can think of to my system are:
    1. Installed a Borland software product (StarTeam) that is newer than my Palm software.
    2. Installed MS Office 2007.
    Please let me know if you need any more information.
    Thanks!
    Post relates to: None

    I would have to recommend you contact your vender where you got the scanner from. If a device got this error that we support we would hard reset the device and rename the backup folder under the username for hotsync. With this device I wouldn't know where to start.

  • T420i - Power Manager - Error occurred while Loading resource DLL

    Hi Team,
    I am facing an issue here, wherein, when I try to start the application : Lenove Power Manager, i get the following error msg:
     "An error occurred while loading resource DLL". I am not sure how to get this working. Can someone please help me out with this.
    Regards,
    Surya

    Welcome to Lenovo Community! Surya
    1. Uninstall existing Power Manager.
    2. Download the new Power Manager from the link below and install:
    http://support.lenovo.com/en_US/downloads/detail.page?DocID=DS014924
    Have a nice day! 
    Peter
    W520 (4284-A99)
    Does someone’s post help you? Give them kudos as a reward, as they will do better to improve | Mark it as solved if the solution works for you, so it could be reference for others in the future
    =====================================
    Sound Enthusiast and Enhancement (Post comments, share mixes, etc.)
    Dolby Home Theater v4 ; IdeaPad Slate Tablet

  • Power Manager Gauge: Error Occurred While Loading Resource Dll

    Just installed windows 10. An dialog window pops up immediately after logon, saying: Power Manager Gauge: "Error occurred while loading resource dll". The power manager driver was up-to-date using System Update and Windows Update. The windows seems working fine after close the dialog. Event log:Faulting application name: rundll32.exe_PWMTR64V.dll, version: 10.0.10240.16384, time stamp: 0x559f39d6Faulting module name: IMM32.dll_unloaded, version: 10.0.10240.16384, time stamp: 0x559f3b64Exception code: 0xc000041dFault offset: 0x0000000000004c70Faulting process id: 0x17bcFaulting application start time: 0x01d0cc1e64ae9c62Faulting application path: C:\WINDOWS\system32\rundll32.exeFaulting module path: IMM32.dllReport Id: dc5d2634-1815-4621-9b48-fdd9d21c8ba8Faulting package full name:Faulting package-relative application ID: 

    Solved. The error comes from the scheduled task by Lenovo Settings Power. By disabling the the task in the Task Scheduler, the error went away. This does not affect the function of Lenovo Settings, just make the power information a bit slow to load.

  • Error -9672 while adding networked printer

    While trying to add a networked HP 3600n color laserjet to the printer list (via Bonjour) on a 10.5.6 G4 Macbook I always ended up with 'an error occurred while trying to add the selected printer' with a -9672 error code. After much deleting of printers, resetting the print system etc. I found that the problem was with the actual printer (another OS X machine turned up the same error). I did a cold reset on the 3600 (hold the tickmark button while the machine starts into its initialization phase after power on, then select COLD RESET from the menus) and re-entered its network settings and the problem on the OS X machines went away.
    Posted here in case anyone else hits this. This same error message and error code appears in other circumstances and these are dealt with in other posts.

    That is a common error, did you download & install the latest hp drivers, generally the ones that come on the CD are out of date!?
    Might try these two after reinstalling the latest driver and repairing Permissions with a reboot afterwards...
    Mac OS X: About the Reset Printing System feature ...
    http://support.apple.com/kb/HT1341?viewlocale=en_US
    Might try Printer Setup Repair 5.1...
    http://www.fixamac.net/software/index.html
    Kappy has further advice here...
    http://discussions.apple.com/thread.jspa?messageID=8266833&#8266833

  • Error occurred during initialization of VM. Could not reserve enough space

    Dear All,
    I am trying to install SAP NetWeaver 7.0 SR2 SP9 on Oracle 10.2 and platform is Windows 2003 32 bits. While installing, in t he restarting the JAVA Instance step, server0 node is getting shutdown. When I further analyzed dev_server0 log, I could get below useful information:
    Error occurred during initialization of VM
    Could not reserve enough space for object heap
    [Thr 6008] JLaunchIAbortJava: abort hook is called
    [Thr 6008] **********************************************************************
    *** ERROR => The Java VM aborted unexpectedly.
    *** Please see SAP Note 943602 , section 'Java VM crashes'
    *** for additional information and trouble shooting.
    [Thr 6008] JLaunchCloseProgram: good bye (exitcode = -2)
    I referred the note mentioned above and it inturn referred to note# 940893. I followed many other sap notes also. However my above problem did not solve yet. I have checke my JAVA SDK version also. It is j2sdk1.4.2_11 and seems to be fine. My systems memory is 3 GB and I gave 20 GB as Virtual memory. I dont think that it should be a memory problem. However somewhere I am lost and can not get the grip over the problem  to resolve it.
    May I request all of you to kindly help me on above issue? Please let me know if you need any more information.
    Waiting for your kind replies.
    Regards,
    Faisal

    Dears,
    Thank you very much for your replies. The heap size was 1024. I changed it to the below:
    Heap Size=512 (earlier 1024)
    Changed below paramters in configtool:
    -Xmx512m (earlier 1024)
    -Xms256m (earlier 1024)
    Hope this information will be helpful to others as well.
    Once again, I thank both of you to guide me in proper directions.
    Regards,
    Faisal

  • An error occurred while preparing the installation. Try running the application again

    I Have erased the hard drive of my MBP in order to perform a clean reinstall of OS X Mavericks, according to these instructions.
    When I tried to reinstall, my internet connection stopped (was broadcasting via another MBP and the cable from that one got disconnected), so I restarted the erased MBP to try again. Holding command+R, it booted in internet recovery (as the recovery partition was erased along with the rest of the hard drive), but could not connect over the broadcasted WiFi, so I created a bootable USB flash drive according to these instructions on the other MBP.
    This installation went smooth without any hiccups, but due to an oversight I had to do it again the next day.
    I took the same steps, with the same bootable drive (I did not create a new one the first time) but this time I couldn’t get through the prepare to install phase. At the end, where the “about a second remaining” message stays for about 20 minutes, I get the “An error occurred while preparing the installation. Try running the application again” message. When I quit the installer (only option at that stage) and return to Disk Utility, the internal drive on which I tried to do the installation is not visible anymore.
    I tried this (after a reboot every time) with a new bootable usb drive with the same download of the OS X Mavericks installer and with a new one, each ending with the same error. The installer was downloaded on an MBP on which Mavericks is also installed, with the same Apple ID. The App Store did not allow me to change Apple ID for the Mavericks download. Can this pose a problem? It did work the first time, though.
    Note that this error occurs at a different stage than the one with the same message due to the wrong date (this discussion amongst others). I also checked the date in terminal and this appears to be correct, when I consider the timezone.
    Here are a few lines from the installer log (omitted similar lines and lines that could contain personal information). The most important line is the last one, indicating the error.
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: @(#)PROGRAM:Install  PROJECT:Install-846
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: @(#)PROGRAM:IA  PROJECT:InstallAssistant-476.8
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Hardware: MacBookPro9,2 @ 2.50 GHz (x 4), 4096 MB RAM
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Running OS Build: Mac OS X 10.9.3 (13D65)
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: DYLD_NO_FIX_PREBINDING=1
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: __CF_USER_TEXT_ENCODING=0x0:0:0
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: PATH=/usr/bin:/bin:/usr/sbin:/sbin
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: PWD=/
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: SHLVL=1
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: __OSINSTALL_ENVIRONMENT=1
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: CI_DEFAULT_OPENCL_USAGE=0
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: OS_INSTALL=1
    Jun 22 02:14:01 localhost Install OS X Mavericks[423]: Env: _=/System/Library/CoreServices/Language Chooser.app/Contents/MacOS/Language Chooser
    Jun 22 02:14:38 localhost Install OS X Mavericks[423]: Using distribution archive from /Volumes/Install OS X Mavericks/Install OS X Mavericks.app/Contents/SharedSupport/OSInstall.mpkg
    Jun 22 02:14:38 localhost Install OS X Mavericks[423]: Configuring products from SharedSupport folder
    Jun 22 02:14:38 localhost Install OS X Mavericks[423]: Install is double-dmg. Not adding chunklist to download list.
    Jun 22 02:14:38 localhost Install OS X Mavericks[423]: Using product <OSInstallDVDProduct> based on media at /Volumes/Install OS X Mavericks/Install OS X Mavericks.app/Contents/SharedSupport at distance 5
    Jun 22 02:14:38 localhost Install OS X Mavericks[423]: Using product <OSInstallESDProduct> based on distribution at /Volumes/Install OS X Mavericks/Install OS X Mavericks.app/Contents/SharedSupport/OSInstall.mpkg at distance 5
    Jun 22 02:14:38 localhost Install OS X Mavericks[423]: Checking Software Update catalog URL https://swscan.apple.com/content/catalogs/others/index-10.9-mountainlion-lion-sn owleopard-leopard.merged-1.sucatalog
    Jun 22 02:14:39 localhost Install OS X Mavericks[423]: JS: installCheckScript threw exception TypeError: 'null' is not an object (evaluating 'my.target.systemVersion')
    Jun 22 02:14:39 localhost Install OS X Mavericks[423]: No available package ref for compatibility update. Ignoring.
    Jun 22 02:14:39 localhost Install OS X Mavericks[423]: *** IFDCustomizationController_10_6 does not know the size of distant package at (null)
    Jun 22 02:14:39 localhost Install OS X Mavericks[423]: *** IFDCustomizationController_10_6 does not know the size of distant package at (null)
    Jun 22 02:14:39 localhost Install OS X Mavericks[423]: Can not connect to /var/run/systemkeychaincheck.socket: No such file or directory
    Jun 22 02:14:39 localhost Install OS X Mavericks[423]: Could not load Software Update catalog: Error Domain=NSURLErrorDomain Code=-1009 "The Internet connection appears to be offline." UserInfo=0x7fedd960ccc0 {NSUnderlyingError=0x7feddc866ef0 "The Internet connection appears to be offline.", NSErrorFailingURLStringKey=https://swscan.apple.com/content/catalogs/others/index-10.9-mountainlion-lion-sn owleopard-leopard.merged-1.sucatalog, NSErrorFailingURLKey=https://swscan.apple.com/content/catalogs/others/index-10.9-mountainlion-lion-sn owleopard-leopard.merged-1.sucatalog, NSLocalizedDescription=The Internet connection appears to be offline.}
    Jun 22 02:14:39 localhost Install OS X Mavericks[423]: Could not fetch SWU catalog to create SWU product
    Jun 22 02:14:49 localhost Install OS X Mavericks[423]: LSExceptions [0x7fedd9446e50] unloaded
    Jun 22 02:15:12 localhost Install OS X Mavericks[423]: No available package ref for compatibility update. Ignoring.
    Jun 22 02:15:12 localhost Install OS X Mavericks[423]: *** IFDCustomizationController_10_6 does not know the size of distant package at (null)
    Jun 22 02:15:12 localhost Install OS X Mavericks[423]: *** IFDCustomizationController_10_6 does not know the size of distant package at (null)
    Jun 22 02:20:55 localhost Install OS X Mavericks[423]: Created IATool object:dbe23a50
    Jun 22 02:20:56 localhost Install OS X Mavericks[423]: Could not find package ref in any source for: com.apple.pkg.BaseSystemBinaries
    —a lot of similar messages, but for other packages —
    Jun 22 02:20:56 localhost Install OS X Mavericks[423]: No available package ref for compatibility update. Ignoring.
    Jun 22 02:21:09 localhost Install OS X Mavericks[423]: Preventing machine sleep.
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Using product IA_PKSecureNetEnabledProduct <file:///Volumes/schijf/OS%20X%20Install%20Data/> at distance 5
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Using existing boot files dir at /Volumes/Install OS X Mavericks/.IABootFiles
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Using mutable product path: /Volumes/schijf/OS X Install Data
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Using boot files path: /Volumes/Install OS X Mavericks/.IABootFiles
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Could not find package ref in any source for: com.apple.pkg.BaseSystemBinaries
    —a lot of similar messages, but for other packages —
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Could not find package ref in any source for: com.apple.pkg.OSInstall
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: No available package ref for compatibility update. Ignoring.
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Could not find package ref in any source for: com.apple.pkg.BaseSystemBinaries
    —a lot of similar messages, but for other packages —
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Could not find package ref in any source for: com.apple.pkg.OSInstall
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: No available package ref for compatibility update. Ignoring.
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Retrieving 0 packages (0.000 GB)
    *****This is where the timer starts saying “”About a minute remaining”*****
    Jun 22 02:21:42 localhost Install OS X Mavericks[423]: Verifying InstallMacOSX.pkg/InstallESD.dmg
    Jun 22 02:42:36 localhost Install OS X Mavericks[423]: Finished operation queue
    Jun 22 02:42:36 localhost Install OS X Mavericks[423]: Opening /Volumes/Install OS X Mavericks/Install OS X Mavericks.app/Contents/SharedSupport/InstallESD.dmg
    Jun 22 02:42:38 localhost Install OS X Mavericks[423]: Extracting boot files from /Volumes/OS X Install ESD/BaseSystem.dmg
    Jun 22 02:42:39 localhost Install OS X Mavericks[423]: Extracting Boot Bits from Inner DMG:
    Jun 22 02:42:41 localhost Install OS X Mavericks[423]: Copied kernelcache
    Jun 22 02:42:42 localhost Install OS X Mavericks[423]: Copied Boot.efi
    Jun 22 02:42:42 localhost Install OS X Mavericks[423]: Copied PlatformSupport.plist
    Jun 22 02:42:42 localhost Install OS X Mavericks[423]: Ejecting disk images
    Jun 22 02:42:42 localhost Install OS X Mavericks[423]: Generating the com.apple.Boot.plist file
    Jun 22 02:42:42 localhost Install OS X Mavericks[423]: com.apple.Boot.plist: {
          "Kernel Cache" = "/.IABootFiles/kernelcache";
          "Kernel Flags" = "container-dmg=file:///Install%20OS%20X%20Mavericks.app/Contents/SharedSupport/ InstallESD.dmg root-dmg=file:///BaseSystem.dmg";
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: Done generating the com.apple.Boot.plist file
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: Blessing /Volumes/Install OS X Mavericks -- /Volumes/Install OS X Mavericks/.IABootFiles
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: Blessing Mount Point:/Volumes/Install OS X Mavericks Folder:/Volumes/Install OS X Mavericks/.IABootFiles plist:com.apple.Boot.plist
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: ***************************** Setting Startup Disk *****************************
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: ******           Path: /Volumes/Install OS X Mavericks
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: ******     Boot Plist: /Volumes/Install OS X Mavericks/.IABootFiles/com.apple.Boot.plist
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: /usr/sbin/bless -setBoot -folder /Volumes/Install OS X Mavericks/.IABootFiles -bootefi /Volumes/Install OS X Mavericks/.IABootFiles/boot.efi -options config="\.IABootFiles\com.apple.Boot" -label OS X Installer
    Jun 22 02:42:43 localhost Install OS X Mavericks[423]: Bless on /Volumes/Install OS X Mavericks succeeded
    Jun 22 02:45:55 localhost Install OS X Mavericks[423]: Got error in writing to /Volumes/schijf/OS X Install Data/minstallconfig.xml
    That last line indicates the error that occurred. (The internal drive on which I try to install Mavericks is called “schijf”, it also already has been called Macintosh HD, with no effect. This time I tried another name during the reformat to see if and when the installer renames the disk. Does it do this, or should I call the disk “Macintosh HD” myself?)
    By now I also got past the internet recovery issues, being able to get the progress bar under the spinning globe and the option to install Lion (not Mavericks, but I suppose that’s because the MBP shipped with Lion). When I choose this option, the installer first spends a few hours downloading additional components. This eventually took less time than first indicated, but still about 4-5 hours. After this, the installation of about 24 minutes starts, but this takes much longer than the indicated 24 minutes, each minute taking about 15 minutes. When it was less than a minute, the internet connection got disconnected (but I don’t suppose it still needed an internet connection at this stage, having downloaded all additional components) and now the “Less than a minute” message has been there the whole night (about 9,5 hours), the last 9 hours with a spinning beachball on the screen after I accidentally clicked somewhere on the screen (nowhere in particular, he shouldn’t do something because of the click. After unplugging the power adapter, the battery icon on the screen wasn’t updated, and the WiFi icon simply disappeared, instead of showing no bars like it should when there’s no connection).
    Does Anyone know how I can fix the error, because I would prefer installing with a bootable drive. Is it worth it to continue waiting on the current, apparently stuck Lion installer to finish or should I force a reboot?
    Can I try using the Recovery Disk assistant (OS X Recovery Disk Assistant v1.0) to create a recovery disk with the other MBP? I think not, as this might cause trouble with 2 different MBP's using the same license.
    Thanks in advance!

    Since this thread seems to be gaining more speed than the other one i'm working on, i figured i'd add these images to help you all out detailing the exact problem.
    I'm having the same issue and I wanted to provide some info specific to my mac, and some info in general to help with diganosis.
    First, my specs
    Secondly, I am running an aftermarket 500 GB drive.
    Third, not sure if this is realated, but this screen suggests the proress will take 3 minutes, then it abruptly umps to the restart phase after about 1.5 - 2.5 minutes.
    And finally, here is the seeminly unavoidable error message.
    Also, other things I've tried now are
    installing it from the "show package contents area",
    mounting said DMG and trying to install from there.
    installing a package file called "upgradeos.pkg"
    no luck.

  • Time capsule won't back up - Unable to complete backup. An error occurred while creating the backup folder. Any ideas?

    I have tried all the resets, the firmware is the latest version, the green light is on.
    But I get this message "Unable to complete backup. An error occurred while creating the backup folder."
    Any ideas?

    Do setup again.. but make sure both your wireless and your ethernet have ipv6 turned on to local link.
    Done this OK, but no idea about IPv6 - something new to me and rather Appley I think?
    Unplug the WAN for the moment.. Just LAN port TC to the MBPr ethernet via thunderbolt.. (thunderbird was the kids puppet series.. Thunderbirds are go!!). Done - New real people Thunderbirds movie coming out soon I believe!!!
    Reset the TC again.. sorry.. !! You're welcome ... done.
    Make sure the ethernet now has an IP address.. 10.0.1.2 - Yep - done that - on ethernet anyway ...
    You need to open the network preferences to find out. Yep - that's good ...
    ****** I then reconnect the TC WAN to the router - is this right?
    And then I think I start going round in circles ... boot, reboot, restart, reboot again ...
    The final result is green light on TC, but error message when trying TM is "Backup disk is not available".
    Then open the airport utility and you should be able to setup the TC.
    Do as little setup as possible and then run the TM backup and see how it goes.
    I have managed to get Thunderbird to LAN on TC to create a folder on TC and copy a file onto it.
    So I guess the drive is working - it must be the software, settings or perhaps even the operator that isn't quite so clever ...
    I named network RFG, named device RFGTC.  RFG network shown as IP 192.168.0.72
    Wireless router is BT Homehub 3 with IP of 192.168.0.254 - is this issuing new IP addresses when rebooting TC?
    I have three wireless networks here - the BT Homehub3 wireless, the TC wireless, and also a D-link power socket ethernet thingy for an ethernet connection to the telly - DHP-W310AV which is also wireless link.  All are effectively connected to the BT Homehub - is there a conflict there?
    Have several times achieved in Airport Utility schematic with internet shown as green, RFGTC shown as green, light on TC green, but no TM backup run ... "backup disc not available."
    And there are no tall building around here to hurl myself off ... at least you can go to Sydney Harbour bridge - not too far away ... it was my son in Sydney that persuaded me to scrap Windows and go Apple ... it's all his fault ...

  • Can't save BISM file pointing to excel sheet (data source). ErrMsg: "There were errors found while validating the page: Cannot connect to the server or database."

    Hi,
    Me and a collegue is administrering our new enterprise BI portal in SharePoint 2013 (On Premise) and have a problem with using a specific Excel file including general ledger data as data source through a BISM file.
    This particular BISM file can't be saved without getting the error message "There were errors found while validating the page: Cannot connect to the server or database."
    BISM files against other Excel sheets and sources (for example SSAS tabular databases) works well.
    Can anyone help us pinpointing whats wrong here, this is a really important stakeholder in our organization requesting this reporting?
    Cheers!

    Hi E.SWARD ,
    My self created a Power pivot excel then i want to use this excel to create BI file . Still i am getting the same error . Pls help me to resolve this issue
    Cannot connect to the server or database.
    I am getting the similar error , if i use Tabular analysis server instance .
    Subhash

Maybe you are looking for

  • Greenish Vertical Lines in Intel imac 21.5" 2008

    I have an intel Imac 21.5" 2008 that has some kind of cloudy greenish vertical lines in pairs all over the screen. Here is a photo http://imageshack.us/f/845/img0041wy.jpg/ Any ideas whats causing this? I had the same problem about a year ago and app

  • Qosmio F30 PQF32E- WI-FI card issue

    Dera all, A long time i am using wi-fi connection for connecting internet. Yesterday i tried to connect wi-fi, i got error. When I am activating wi-fi in notebook, it is getting frozen or working very very slow and even wi-fi card disabled. i am enab

  • How to put pictures into folders

    How do I put pics into folders?

  • Difference between Analyzer Java & HTML Client

    Hi,Does anyone know all the differences between Analyzer Java & HTML Client.A couple of diffence I noticed are:1. HTML Client doesn't support Linked Reporting Objects (LRO)2. HTML Client doesn't seem to support Navigate functionality in Java client.A

  • SQLServer 2000 & JDBC

    Hi, I still have problems with the SQL Server 2000 drivers for JDBC. The documentation shows that .beforeFirst(), .absolute() and others methods are available but when i run my app, I have the error : [Microsoft][SQLServer 2000 Driver for JDBC]Unsupp