Error 229771 DAQmx create task internal MIG error

Receiving error 229771 @ DAQmx create task.vi: 2, internal error in MIG software. not start task. - for a simple ThermoDAQ read application
reinstalled drivers, attempted to start NI configuration mgr and Device loader but they are immediately stopped- disabled anti virus, etc. help?

Hi eremark,
There are a few things we can try to troubleshoot error 229771. This error can occur if NI services are not running and occurs when LabVIEW tries to communicate to these non-running services. It can also occur if you have a corrupt MAX database. There are a few things we can try
1. Can you please try verifying if NI services are running?
2. Can you check if you are administrator of your PC?
3. Do you know if DAQmx was installed under an administrator account?
4. Have you tried disabling your firewall?
5. Try removing all DAQ devices, restarting your computer with them removed, shutting down the computer again and connecting them back up.
6. Did you repair your daqmx drivers or reinstall them? It is important to make sure you do a true reinstall (http://digital.ni.com/public.nsf/allkb/ADD22E807D5A12AD862579EC00760F79?OpenDocument) instead of repair which will force overwrite anything from previous installations
7. Try repairing a corrupted MAX database - http://digital.ni.com/public.nsf/allkb/86256F0E001DA9FF86256FFD005B827C?OpenDocument http://digital.ni.com/public.nsf/allkb/7FF79722720AEE488625759B0074A2CA?OpenDocument
Please let me know if you have any questions or need any clarification with any of these troubleshooting steps. Thanks
Doug W
Applications Engineer
National Instruments

Similar Messages

Does multiple instances of DAQmx start task result in error?

I am trying to read voltages from pressure transducers and LVDTs in two separate While Loops. But when running the program there is an error regarding DAQmx Start Task.vi. So I was wondering if multiple instances of DAQmx Start task results in error. I have attached the vi.
Thanks
Attachments:
IsoConsolidationDAQMAX02.vi ‏140 KB

Thank you for the reply. New to Labview so I didn't know that we had to search using the error code, I tried searching using text though. Will do that from the next time, thanks.
I do not have the problem with the write tasks but only with the read tasks. Right now I have one start task for all the input from the pressure transducers and LVDTs and three start tasks for the three analogue outputs and the program seems to run fine.

SOAP Receiver- Error While Sending Message: 500 Internal Server Error

Hello,
Our scenario: IDoc to SOAP
I have added a third party system in the SLD and have used the same in my ID configuration.
An idoc will be triggered from R/3, which will received in PI, PI will transform the IDoc into SOAP message for the third party system.
I have tested the scenario in ID from Interface Determination and its successful.
But when i try to try to test it from RWB, using Test Message in Adapter Engine, I get an error,
"Error while sending message:500 Internal server error"
If we test it using a testing software like SOAP UI, it works fine but from PI we get the error mentioned above.
Regards,
Abhishek

Hello,
Since the IDOC adapter resides on the ABAP stack, you can use this URL instead (it will be sent to the integration engine as Venkata suggested)
http://host:port/sap/xi/engine?type=entry
Also check your firewall settings from PI to the third-party system.
Hope this helps,
Mark
Edited by: Mark Dihiansan on Feb 7, 2012 11:48 AM

Imp: Error while sending message: 500 Internal Server Error

Hi all
while testing my scenarios- by sending the message through component monitoring in RWB I get the following error in Integration Server
<b>"Error while sending message: 500 Internal Server Error "</b>
It seems that integration server is not picking up the messages.
Can anyone help me on this?
thanks
Abhishek

Hi Abhishek,
Check whether the integration url is pointing to correct one something like http://host url:http port/sap/xi/engine?type=entry.
Please do refer the below blog:
/people/krishna.moorthyp/blog/2006/07/23/http-errors-in-xi
Regards,
Prasanthi.

Error when sending message: 500 Internal Server Error

Hi
IE is not accepting any messages,
when I try to send the messgae to the IE ( using RWB) i am getting the below error " Error when sending message: 500 Internal Server Error".
following things what i have noticed.
1. Pipleline URL is fine, both in the BS of XI and in the RFC destnation which i am maintaing on the IE admin) URL is "http://<host>:8000/sap/xi/engine?type=entry"
2. SICF all the XI serivess are up and running, i am able to test these service.
3. The http port is active ( SMICM )
Pls note the error is 500 Internal Server Error
regards
Nisar

I think in a simple term 500 can be said as "the request cannot be processed curretnly", these options mentieoned by you are not applicable in my case.
This generally occurs due to load problem or if you are on an SP less than 12 or even if there is an administration problem---I am on PI7.0 , what are the administration problem you are talking about?
1 Check Table Space is enough. ---i had installed server recently & very few interface running.
2 Server licence Date or Time. In this case change system date and restart server.---i have recently installed server.
3 Check the service pack levels on your XI. If it is obsolete upgrade it with latest versio----Can u explain more on this?
Try restart the java stack(XI Server) and follwing services.
com.sapii.af.app ---I am not passing trough Adater framework, so i dont think this service will matters....
com.sapii.cpa.af.app.---CPA cahe is done sucessfully, as i said i am not passsing through adapter framework.
basically for a simple HTTP post what might cause 500 error if all necessary services are up and running?
regards
Nisar

Missing DAQmx Create Task.vi among others

Hi all,
I'm trying to run a .vi made in Labview 8.5 using Labview 2012. I have the most recent version of DAQmx (9.5) installed, but it's unable to find the file DAQmx Create Task.vi, and if I chose to ignore it about 6 other files pop up that it is also unable to find. I have uninstalled and installed DAQmx on both my computer and two other computers running Labview 2009 to try and get this to work, but nothing seems to be solving the problem. Any ideas what might be going wrong here?
Thanks!

Are you trying to open the VIs using 8.5 or 2012? Are the DAQmx VIs in the palette?
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

How to remove channel from DAQmx create Task.vi

Vikas H. Kumthekar
ASE
Tata Consultancy Services
Pune-1

How are you using the DAQmx Create Task.vi? Are you using it to include a global channel or copy a task that was previously created in Measurement and Automation Explorer (MAX)? If this is the case the only way to remove a channel would be to delete the global channel or modify the physical channels for that task in MAX. If you are creating a new task you can use the DAQmx Create Channel.vi to specify the physical channels that you would like to include or exclude.
Regards,
Andy F.
Applications Engineer
National Instruments
National Instruments

Error 0006:1860:4027 500 internal server error

When I click on Sync for Active sync to run, it seem to sync up the contacts, calendar and the mails but at the end of it , it fails with the following error message:
Error: 0006:1860:4027 500 Internal Server Error Connection: Keep-Alive
Set-Cookie: cadata5E523BEF14254CCA84573DC7AEDE0815="1d5b1d099-017f-
I dont have access to the Exchange Server nor our IT will be able to help me with this. Any help why this is happening will be very much appreciated.
It worked perfectly with my Earlier Centro device. I got it replaced today due to some hardware issue and this wont just wont sync without this error.
Thanks
Post relates to: Centro (Unlocked GSM)

Hello!
Could be due to too much content being indexed for that initial sync and the buffer for the phone is being overtaxed. You could try to change the filter to get the last 1 day of message and subject only but oftently this is solved by moving a good chunk of the emails/contacts/calendar in Outlook/OWA into sub folders and do another sync. If its ok, then start moving the data back into the parent folders little bit at a time between sync to ensure your not going to exceed the buffer on the Centro.
The catch for EAS is that it wants to index EVERYTHING on your exchange server for that inital sync.
Message Edited by thetreoguy on 05-13-2009 04:46 PM

Error -200431, DAQmx Create Channel (AI-Voltage-Custom with Excitation).vi

Where is "DAQmx Create Channel (AI-Voltage-Custom with Excitation).vi" gone?
I tried to use this VI for force measurement with a NI PXI-4472. It responds with Error -200431, ... You Have Requested: More:Voltage:Custom with Excitation, You Can Select: Voltage, Sound Pressure:Microphone, ...
It seems for me to be an internal error of this VI, LabView Version is 8.6.1
Solved!
Go to Solution.

Hi T.Knox,
error -200431 is a measurement type error:
"Error -200431 occurred at an unidentified location. Possible reason(s):
Measurements: Selected physical channel does not support the measurement type required by the virtual channel you are
creating. Create a channel of a measurement type that is supported by the physical channel, or select a physical channel
that supports the measurement type."
The PXI-4472 (8 Inputs, 24-Bit Dynamic Signal Acquisition module for sound and vibration measurement) is the wrong device
for force measurement.
I also searched our website and found some helpful links:
http://zone.ni.com/devzone/cda/tut/p/id/3602#toc2
The PXI-4472 (http://sine.ni.com/nips/cds/view/p/lang/en/nid/5031) isn't listed as supported device for force measurement
there!
I hope this information helps you!
Regards
Suse
Certified LabVIEW Developer (CLD)

Error assigning and creating tasks problem!

I am using Sharepoint Designer 2013 to create task in a workflow and I get the following message when publushing it:
Microsoft.Workflow.Client.ActivityValidationException: Workflow XAML failed validation due to the following errors: Cannot set unknown member 'CompositeTask.RelatedContentLinkListItemIntegerId'. HTTP headers received from the server - ActivityId: e8e6d4fe-2a4e-41df-a046-a88e93e89e27.
NodeId: FS0008. Scope: /SharePoint/default/5985c481-dbed-409b-ada8-2aa2bfc64a47/08f0ee16-a466-4797-9ee0-4cdc56b27fe7. Client ActivityId : 403fe49c-6f29-f019-9b9c-d69dcbbedef6. ---> System.Net.WebException: The remot
For whats is worth my connection with the site is okay, for I am able to publish a workflow changing status, sending e-mails and other simple options.
The solutions I found on the web it's using SharePoint 2013 Management Shell, but didn't seem to work at all. Any suggestions?

Hello Julio,
The current forum is for Office Apps. I'd suggest asking SharePoint specific questions on the
SharePoint 2013 - Development and Programming forum instead.

" Error while sending message: 500 Internal Server Error" RNIF Adapter

Hi,
I have configured B2B integration as   Sender : RNIF adapter & Receiver: XI Adapter.
I am able to test the configuration successfully in ESR and ID. But, whille testing with RWB using same test data, i am getting the following error:
Error while sending message: 500 Internal Server Errot.
     Could you anybody help me, what could be the reason? Even i am not getting any error messages in SXMB_MONI.
Thanks
Laxman

Hope this helps..
-Is the 500 internal SErver Error in RWB is only for this issue and the message is successfully processed in SXMB_MONI?
   Could be the PI Service User :PIAFUSER(Adapter framework user) login crendential issue or run out time error.
Try taking the payload from sxmb_moni and enter it in RWB > Adater engine> Test Message Tab > give proper sender interface information , enter payload and try sending message.   check what is behaviour

How to find error details when getting 500 Internal Server Error

Hi Everyone,
I get 500 Internal Server Error on b2b order main page after modified tabstrip.inc.jsp. I want to see the detail error messages, but don't know how to. Any advises?
Thanks, Jin

Hi Jin,
From code.
You please check it again.
You have written below lines in your code.
<%@ page import com.sap.isa.core.xcm.ConfigContainer %>
<%
UserSessionData userData = UserSessionData.getUserSessionData(request.getSession());
ConfigContainer configcontainer = (ConfigContainer)(userData.getCurrentConfigContainer());
String sName = configcontainer.getScenarioName();
I think check your first line of import. It should be
<%@ page import="com.sap.isa.core.xcm.*" %>
I think you forgot to put = and ". See above line. and check your code again.
Regards.
eCommerce Developer

403 error accessing ADF app / 500 Internal Server Error accessing page

Jdeveloper 10.1.3.2
AppServer 10.1.3
I have developed and ADF-BC application. It runs great using the local embedded oc4j server. I setup a deployment profile and used the ear file to deploy to the application server. It deploys without error. When I try and test it by drilling down to the app in the enterprise manager, I get a 403 forbidden error. If I try and access the main jspx page directly (http:/server:port/myapp/faces/app/myapp.jspx), I get a 500 Internal Server Error with the following text:
java.lang.NoSuchMethodError: oracle.adf.share.perf.StateTracker.isActive()Z
at oracle.adf.model.servlet.ADFBindingFilter.doFilter(ADFBindingFilter.java:137)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:627)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:376)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.HttpRequestHandler.doProcessRequest(HttpRequestHandler.java:870)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:451)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.AJPRequestHandler.run(AJPRequestHandler.java:299)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].server.http.AJPRequestHandler.run(AJPRequestHandler.java:187)
at oracle.oc4j.network.ServerSocketReadHandler$SafeRunnable.run(ServerSocketReadHandler.java:260)
at com.evermind[Oracle Containers for J2EE 10g (10.1.3.0.0) ].util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:303)
at java.lang.Thread.run(Thread.java:595)
Thanks in advance for any help.
Message was edited by:
jnewhart

I have updated the ADF library on the application server per this document.
http://www.oracle.com/technology/products/jdev/howtos/10g/adf_runtime_update_howto.html
I used the manual method since jdeveloper is not installed on the AS. If it were I would use the ADF installer. Unfortuantely, it did not seem to help.

Missing SubVI DAQmx Create Task. Error

Hi All,
I have written a program in Labview 2009 and I am using the PCI-6034E DAQ card for measuring data. I created an executable of this program, and I wanted to run the program on another computer, although this computer is running the PCI-6024E DAQ card. However, when I run the program, I get the error message which is attached.
I have downloaded the Runtime Engine for labview 2009 on this computer, So I'm not sure why the program isn't working. I have also checked the measurement instrumentation on the computer with the PCI-6024E and it detects the card and can make measurements and is also using the same channel as I was using with the PCI-6034E card. Could someone please let me know how I can fix the problem?
Thanks.

DAQmx Base is a completely different driver than DAQmx. You cannot install DAQmx Base and use DAQmx functions. When you create the installer, select DAQmx to include as one of the 'Additional Installers'
Actually, I get the feeling that you totally skipped over creating an installer. This is an option when you right click on 'Build Specifications' and is something you should have noticed when you created the exe.

Error in Error -200485 occurred at DAQmx Create Task.vi:2

I keep having this error:
The specified task cannot be loaded, because it is not in Data Neighborhood.
Check Data Neighborhood in MAX. Look for similar characters, such as the capital letter "O" and the number zero.
I would like to know what is the problem with the program. I've attached the VI.
Basically i am trying to control a physical LED connected to the NI Elvis II by comparing the inputs from DIO 0-7 and DIO 8-15.
So if DIO 0 is on, DIO 8 must also be on to turn on the LED.
But at the moment, the program cant run. Need help in spotting the mistake! >< Thanks!
Solved!
Go to Solution.
Attachments:
Untitled 2.vi ‏94 KB

From the code you attached I guess you haven't created a task (This is used to configure which is input and which is output) so you can take a look at the page how to create a task and go ahead.
Good luck
The best solution is the one you find it by yourself

Error 229771 DAQmx create task internal MIG error

Similar Messages

Maybe you are looking for