Error 54 in udp write when sending to ip 127.0.0.1 !

hello friends !
i have installed labview 2012 and my projects (which i wrote in labview 2010) have some incompatibility issues.
one of them is error 54 (the network address is ill-formed etc...) when trying to send data to myself - to IP 127.0.0.1
in labview 2010 it was OK. now it is an error.
can someone help ?
Solved!
Go to Solution.

Could be rather a network card driver problem than a LabVIEW one. If you wire an IP address to the Open function you tell the socket to route all traffic through that network. Technically 127.0.0.1 is the loopback device which is a virtual network card in itself so depending how the network socket stack is configured to route the traffic, the order to route the traffic through a specific physical network device may prevent it to ever reach the local loopback device.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Similar Messages

Fatal Internal error: "oleautomgr.cpp", line 2832 when sending data by means of ActiveX methode

I have experienced error "Fatal Internal error: "oleautomgr.cpp", line 2832" during sending data to CAN card IXXAT iPCI-I XC16/PCI. LabVIEW communicates with that card by means of ActiveX methodes via "VCI Wrapper" which is COM object interface. Mass compiling of the project does not help. Card is initialized and configured propely. The driver card is working propely.
LabVIEW version is 8.5
The efect of that error is that labview completly shot down.
I appraciate any suggetions
thanks a lot

Hello,
Please try to reinstall the drivers for the CAN card, then make sure you close all references to the ActiveX control (at all levels) using the Automation Close primitive in LabVIEW.
Regards,
Emil

Error message on phone number when sending imessages

my imessages are sending from my email account, when i went to settings>messages> recieve at> I have an error code at my phone number and only able to send as an email

cmp007 wrote:
Is there anyway to keep the stuff on the phone. I really need the stuff in it and cant afford to wipe it clean
The only way to keep your stuff on the phone is if you remember your passcode. Like the other poster mentioned, someone probably tried to get into your phone and tried various combinations. After 10(?) attempts, the iphone will lock and make you restore your phone from itunes.

Error message in report writer when add new selection filed?

Dear All,
I wanna add a new selection field cost element group and cost element to a report in report writer. I key in GR52 and click the general data selection. I select the set variable &1KSTAR to enter into the set ID. But it shows me the following message:
Set cannot be used in Selection:
Message no. GR807
Diagnosis
You are trying to use a set in report maintenance.
The set cannot be entered in the report definition for any of the dimensions for which the set could be used.
The following error message describes why the set cannot be used for all the dimensions for which the set can be used.
System Response
The set will not be entered in report maintenance.
Procedure
Choose an appropriate set.
What does it mean? I have tried other set variables but sitll gave the same message.
Thank you and good day.
Emma.

At the same time, it gave me a green light message saying:
Characteristic Cost Element is already used in a row
Message no. GR465
Diagnosis
The characteristic Cost Element is already being used in a report row block and therefore cannot be used in a different part of the report.
Technical note: The field name for characteristic Cost Element is KSTAR.
Does it mean I have used the cost element in the report and blocked the cost element so that I can't use it in the selection screen? How can I solve this by not changing the report or should I change the report?
Thank you and good day
Emma

Getting error in the adapter engine when sending a message

Hi,
I'm always getting this error in the adapter engine: Message processing failed. Cause: com.sap.aii.messaging.util.URI$MalformedURIException: no scheme
The comm channel ends up in error because of messages having the above error.
Could someone please help?
Thanks.
Mike

Mike.
Please check this links.
Check your adapter and restarted.
com.sap.aii.messaging.util.URI$MalformedURIException: invalid port number
Re: Prerequisites to setup configure mail scenario.
error in communication channel
Error :Receiver File Channel not Initialized

Error 554-5.6.0 Corrupt message content... when sending emails to other users on same exchange server

Hello
I have a very strange problem at a customer from our company.
The problem happens to only one user on the Exchange 2010 organization (SP3, no additional patches installed, Server is 2008 r2).
When this specific user sends an email to one or more users on the same Exchange organization, he gets sometimes (not always) the following error back:
554-5.6.0 Corrupt message content 554 5.6.0 STOREDRV.Deliver.Exception:ConversionFailedException; Failed to process message due to a permanent exception with message Inhaltskonvertierung: Fehlerhafter TNEF-Zusammenfassungsinhalt. ConversionFailedException:
Inhaltskonvertierung: Fehlerhafter TNEF-Zusammenfassungsinhalt. [Stage: CreateReplay]
So - TNEF, corrupt message Content... I googled the error and checked all the recommended Solutions. The Outlook Client is ok, I have doublechecked it and everything is configured like it has to be.
The Problems happens as above described only for one user when he writes emails to users from one specific Domain on the same Exchange organization (example
[email protected]).
He has this specific contacts in a SharePoint contact list which is connected to his Outlook Client.
Thanks for any help or Information!
Regards

Hi,
According to your description, I understand that one user cannot send message with error “554-5.6.0 Corrupt message content 554 5.6.0”.
If I misunderstand your concern, please do not hesitate to let me know.
I want to double confirm whether it works or not when send message to external address, how about the OWA?
It seems that message has corrupt content. Is there any 3rd prevent software or Anti-Virus software in Exchange 2010?
Regarding this issue, firstly I would like to explain that content conversion occurs in two places, that are the Store Driver and the Content Conversion stage of Categorization. Since the issue exists in the delivery mail of internal user, the agent that was
used in the process of handling by Store Driver may cause this issue.
Please try to enable pipeline tracing and content conversion tracing to get more details about this error, for your reference:
Content conversion tracing:
http://technet.microsoft.com/en-us/library/bb397226.aspx
Pipeline tracing:
http://technet.microsoft.com/en-us/library/bb125018.aspx
Best Regards,
Allen Wang

Error when send file by RMI

I take application RMI client, server.
Client will auto print screen by 3 seconds, when send to server.
Server delete picture old and update picture new.
But client only send a first time, next time is throw Exception "java.io.IOException: Write error"
Server_
import java.rmi.Remote;
import java.rmi.RemoteException;
public interface IUpload extends Remote{
     public void close() throws RemoteException;
     public void sendData(byte[] data, int offset, int length) throws RemoteException;
     public void sendFileName(String fileName) throws RemoteException;
import java.io.File;
import java.io.FileOutputStream;
import java.io.IOException;
import java.rmi.RemoteException;
import java.rmi.server.UnicastRemoteObject;
import java.util.Date;
public class UploadServer extends UnicastRemoteObject implements IUpload{
    public UploadServer() throws RemoteException {
          super();
     FileOutputStream fout = null;
     public void close() throws RemoteException {
          if(fout != null) {
               try {
                    fout.close();
               } catch (IOException e) {
                    e.printStackTrace();
     public void sendData(byte[] data, int offset, int length) throws RemoteException {
          if(fout != null) {
               try {
                fout.flush();
                    fout.write(data, offset, length);
                    fout.flush();
               } catch (IOException e) {
                    System.out.println("Error sendData " + e);
            System.out.println("Nhan file " + (new Date()).toString());
     public void sendFileName(String fileName) throws RemoteException {
        File file = new File(fileName);
        if ( file.exists() ){
            System.out.println("File nay da ton tai va da xoa");
            file.delete();
        else {
            System.out.println("File nay chua ton tai");
        if(fout == null) {
               try {
                    fout = new FileOutputStream(fileName);
               } catch (Exception e) {
                    System.out.println("Err sendFileName " + e);
import java.rmi.Naming;
import java.rmi.RemoteException;
public class RunServer {
     public static void main(String[] args) throws RemoteException {
        //java.rmi.registry.LocateRegistry.createRegistry(8585);
        IUpload download = new UploadServer();
        try {
            Naming.rebind("Server", download);
            System.out.println("Khoi dong server thanh cong...");
        catch (Exception exp){
            System.out.println("Err " + exp);
Client_
import java.awt.*;
import java.awt.image.*;
import java.io.*;
import java.rmi.Naming;
import javax.imageio.*;
public class CaptureScreen {
    String outFileName;
    public CaptureScreen(String fileName) {
        outFileName = fileName;
    public void Send() throws Exception
        Toolkit toolkit = Toolkit.getDefaultToolkit();
        Dimension screenSize = toolkit.getScreenSize();
        Rectangle screenRect = new Rectangle(screenSize);
        Robot robot = new Robot();
        BufferedImage image =
                robot.createScreenCapture(screenRect);
        ImageIO.write( image, "jpg", new File(outFileName) );
        try {
            IUpload upload = (IUpload)Naming.lookup("//localhost/Server");
            upload.sendFileName(outFileName);
            FileInputStream fin = new FileInputStream(outFileName);
            byte[] data = new byte[8000];
            int lengthFile = fin.read(data);
            int offset = 0;
            while ( lengthFile != -1 )
                upload.sendData(data, offset, lengthFile);
                lengthFile = fin.read(data);
            upload.close();
            fin.close();
        catch (Exception exp){
            System.out.println( exp.toString() );
public class RunClient {
    public static void main(String[] args) throws Exception
        while (true)
            try {
                System.out.println("Waiting 3 seconds....");
                Thread.sleep(3000);
            catch (Exception exp){
                System.out.println("Err " + exp);
            CaptureScreen screen = new CaptureScreen("screen.jpg");
            screen.Send();
}

throw Exception "java.io.IOException: Write error"Who threw it, the client or the server? At what line of code?
You'd be better off declaring those remote methods to also throw IOException and let it be thrown back to the client if it happens, rather than catching it silently inside the server. That way the client knows the server is failing and can made a decision about whether to continue.The client should also show the complete stack trace, not just the message.

I have recently bought a macbook and am using outlook 2011 as email. i am getting an error message 4.7.0 not allowed when sending emails how do I fix?

i have a macbook and am using outlook 2011 as email. receiving okay. sending okay sometimes. am now getting error message 4.7.0 not allowed when sending. what is the cause? how do I fix please?

I have discovered that the emails have in fact been sent but much later, maybe it's a network problem with the people i am sending it to. so i checked my sent items and they are there, but at the time the email doesn't go straight into the sent box or drafts so i'm assuming it's disappeared and type it again. i'll keep going with it, until someone can give me a possible solution or explanation as to what is happening.

Error message when sending photos as attachments in mail

When sending photos from i photo in mail I get an error message "Can't get paragraph 8 of content of outgoing message id 142504208. Invalid Index" I can send one photo at a time but no more than one. I have recently upgraded to leopard from panther. I tried rebooting but no success. Any suggestions greatly appreciated.

Bump. I have the same problem. Anyone shed some light on this?

Could not initialize the browser's security component Error message when sending a link

Using Ubuntu 9.10 64 bit. Firefox version is 3.6.3 and Thunderbird version is 2.0.0.24
When sending a link with Firefox I get an error message "Could not initialize the browser's security component...". Tried deleting the cert8.db and secmod.db. Noticed if Thunderbird is already open I don't get the error message. But if Thunderbird is closed then opens to send the link I get that error message. Seems the security certificates aren't being passed to Thunderbird when it is opening up.
== This happened ==
Not sure how often
== 2 days ago.

Try to remove or rename the secmod.db (secmod.db.old) file in the Firefox Profile Folder.
If that didn't help then remove or rename cert8.db (cert8.db.old) as well.
You can use this button to go to the Firefox profile folder:
*Help > Troubleshooting Information > Profile Directory: Show Folder
*http://kb.mozillazine.org/Profile_folder_-_Firefox
* C:\Users\<user>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\
The "Application Data" folder in XP/Win2K and the "AppData" folder in Vista/Windows 7 are hidden folders.
*http://kb.mozillazine.org/Show_hidden_files_and_folders

Since installing the latest update my mother-in-law gets Error Code VM502 when sending to only 6 recipients

Since installing the latest update my mother-in-law gets Error Code VM502 when sending to only 6 recipients. This didn't happen before the update.

The error came from your providers server. You need to ask them why they are setting limits.
Thunderbird does not have any limits.

Error when sending message: 500 Internal Server Error

Hi
IE is not accepting any messages,
when I try to send the messgae to the IE ( using RWB) i am getting the below error " Error when sending message: 500 Internal Server Error".
following things what i have noticed.
1. Pipleline URL is fine, both in the BS of XI and in the RFC destnation which i am maintaing on the IE admin) URL is "http://<host>:8000/sap/xi/engine?type=entry"
2. SICF all the XI serivess are up and running, i am able to test these service.
3. The http port is active ( SMICM )
Pls note the error is 500 Internal Server Error
regards
Nisar

I think in a simple term 500 can be said as "the request cannot be processed curretnly", these options mentieoned by you are not applicable in my case.
This generally occurs due to load problem or if you are on an SP less than 12 or even if there is an administration problem---I am on PI7.0 , what are the administration problem you are talking about?
1 Check Table Space is enough. ---i had installed server recently & very few interface running.
2 Server licence Date or Time. In this case change system date and restart server.---i have recently installed server.
3 Check the service pack levels on your XI. If it is obsolete upgrade it with latest versio----Can u explain more on this?
Try restart the java stack(XI Server) and follwing services.
com.sapii.af.app ---I am not passing trough Adater framework, so i dont think this service will matters....
com.sapii.cpa.af.app.---CPA cahe is done sucessfully, as i said i am not passsing through adapter framework.
basically for a simple HTTP post what might cause 500 error if all necessary services are up and running?
regards
Nisar

RFC error when sending logon data

Hi;
We cannot configure the STMS of our development system. When we try to
configure it, system gives an error message: Errors during distribution
of tp configuration; TMS Alert Viewers tells us
RFC_COMMUNICATION_FAILURE: RFC communications error with
system/destination TMSADM-FKT.DOMAIN_FKT RFC error when sending logon
data and READ_PROFILE_FAILED:File
erptest\sapmnt\trans\bin\TPPARAM
could not be opened for reading (No such file or directory).
Is there any advise for solution?
Best regards
Noyan
PS: Please find the profiles below:
START:
#.*       Start profile START_DVEBMGS00_erptest                                                                                *
#.*       Version                 = 000006                                                                                *
#.*       Generated by user = BASIS                                                                                *
#.*       Generated on = 30.12.2010 , 15:40:55                                                                                *
generated by R3SETUP
SAPSYSTEMNAME = FKT
INSTANCE_NAME = DVEBMGS00
SAPSYSTEM = 00
SAPGLOBALHOST = erptest
DIR_PROFILE = D:\usr\sap\FKT\SYS\profile
start database
#_DB = strdbs.cmd
#Start_Program_02 = immediate $(DIR_EXECUTABLE)\$(_DB) FKT
start message server
#_MS = msg_server.exe
Start_Program_03 = local $(DIR_EXECUTABLE)\$(_MS) pf=$(DIR_PROFILE)\FKT_DVEBMGS00_erptest
Start IGS
Start_Program_05 = local $(DIR_EXECUTABLE)$(DIR_SEP)igswd$(FT_EXE) -mode=profile pf=$(DIR_PROFILE)$(DIR_SEP)FKT_DVEBMGS00_erptest
start application server
#_DW = disp+work.exe
#Start_Program_04 = local $(DIR_EXECUTABLE)\$(_DW) pf=$(DIR_PROFILE)\FKT_DVEBMGS
General parameters for starting the system
#parameter created                          by: BASIS        24.12.2007 23:53:27
#SAPSYSTEM = 00
#parameter created                          by: BASIS        24.12.2007 23:53:27
#SAPSYSTEMNAME = FKT
#parameter created                          by: BASIS        24.12.2007 23:53:27
#INSTANCE_NAME = DVEBMGS00
#parameter created                          by: BASIS        24.12.2007 23:53:27
DIR_PROFILE = D:\usr\sap\FKT\SYS\profile
#parameter created                          by: BASIS        24.12.2007 23:53:27
#SAPGLOBALHOST = erptest
Start database
#parameter created                          by: BASIS        24.12.2007 23:53:27
_DB = strdbs.cmd
#parameter created                          by: BASIS        24.12.2007 23:53:27
Start_Program_01 = immediate $(DIR_EXECUTABLE)\$(_DB) $(SAPSYSTEMNAME)
Start message server
#parameter created                          by: BASIS        24.12.2007 23:53:27
MS = msgserver.exe
#parameter created                          by: BASIS        24.12.2007 23:53:27
Start_Program_02 = local $(DIR_EXECUTABLE)\$(_MS) pf=$(DIR_PROFILE)\FKT_DVEBMGS00_erptest
Start applications server
#parameter created                          by: BASIS        24.12.2007 23:53:27
_DW = disp+work.exe
#parameter created                          by: BASIS        24.12.2007 23:53:27
Start_Program_03 = local $(DIR_EXECUTABLE)\$(_DW) pf=$(DIR_PROFILE)\FKT_DVEBMGS00_erptest
DEFAULT:
SAPDBHOST = ERPTEST
dbms/type = mss
dbs/mss/server = ERPTEST
dbs/mss/dbname = FKT
dbs/mss/schema = fkt
SAPSYSTEMNAME = FKT
SAPGLOBALHOST = erptest
SAPFQDN = tr.delta.is
SAPLOCALHOSTFULL = $(SAPLOCALHOST).$(SAPFQDN)
SAPDBHOST = erptest
SAPTRANSHOST = erptest
DIR_TRANS =
$(SAPTRANSHOST)\sapmnt\trans
#DIR_TRANS = D:\usr\sap\trans
DIR_PROFILE = D:\usr\sap\FKT\SYS\profile
SAP Message Server for ABAP
rdisp/mshost = erptest
rdisp/sna_gateway = erptest
rdisp/sna_gw_service = sapgw00
rdisp/vbname = erptest_FKT_00
rdisp/enqname = erptest_FKT_00
rdisp/btcname = erptest_FKT_00
rdisp/msserv = sapmsFKT
rdisp/msserv_internal = 3900
rdisp/bufrefmode = sendoff,exeauto
login/system_client = 200
#GUVENLIK PARAMETRELERI
login/password_expiration_time = 90
login/min_password_lng = 6
#parameter created                          by: BASIS        25.03.2004 08:41:25
rdisp/gui_auto_logout = 10800
#parameter created                          by: BASIS        25.03.2004 08:37:47
#old_value: 3                                 changed: BASIS 25.03.2004 08:42:38
login/fails_to_user_lock = 6
#validasyon geregi, g#venligi artirma ama#i - check active but no check for SRF
#parameter created                          by: BASIS        16.06.2007 17:35:41
#old_value: 2
#changed: BASIS         14.05.2008 15:24:55
auth/rfc_authority_check = 1
#otomatik unlocki iptal eder
#parameter created                          by: BASIS        10.11.2006 17:47:15
login/failed_user_auto_unlock = 0
#AUDIT PARAMETRELER?
#old_value:                                   changed: BASIS 20.04.2005 17:13:37
rsau/max_diskspace/per_day = 1996800000
#old_value: 1000000000                        changed: BASIS 20.04.2005 17:17:01
#old_value: 0                                 changed: BASIS 20.04.2005 17:19:12
rsau/max_diskspace/local = 2048000000
#old_value: 2000000000                        changed: BASIS 28.03.2005 23:17:11
#old_value: 2                                 changed: BASIS 29.03.2005 12:09:14
#old_value: 0                                 changed: BASIS 20.04.2005 17:13:37
rsau/max_diskspace/per_file = 665600000
rsau/enable = 1
rsau/local/file = D:\usr\sap\FKT\DVEBMGS00\log\++++++++######..AUD
rsau/selection_slots = 12
#rec/client = ALL
DIR_AUDIT = D:\usr\sap\FKT\DVEBMGS00\log
FN_AUDIT = ++++++++######..AUD
#DIL PARAMETRELERI
#Turkish codepage settings
abap/import_char_conversion = 0
install/codepage/db/non_transp = 1610
install/codepage/db/transp = 1610
zcsa/installed_languages = DET
#zcsa/system_language = E
zcsa/system_language = T
zcsa/second_language = E
install/codepage/appl_server = 1610
#OS dependent
abap/locale_ctype = Turkish_turkey.28599
#DIR_PUT = D:\usr\sap\FKQ\upg\abap
   *** UPGRADE EXTENSIONS (RELEASE "701") ***
#rdisp/msserv_internal = 3900
#system/type = ABAP
INSTANCE:
SAPSYSTEMNAME = FKT
SAPGLOBALHOST = erptest
SAPSYSTEM = 00
INSTANCE_NAME = DVEBMGS00
DIR_CT_RUN = $(DIR_EXE_ROOT)\$(OS_UNICODE)\NTAMD64
DIR_EXECUTABLE = $(DIR_INSTANCE)\exe
icm/server_port_0 = PROT=HTTP,PORT=80$$
SAP Message Server parameters are set in the DEFAULT.PFL
ms/server_port_0 = PROT=HTTP,PORT=81$$
#rdisp/wp_no_dia = 10
#rdisp/wp_no_btc = 3
#rdisp/wp_no_enq = 1
#rdisp/wp_no_vb = 1
#rdisp/wp_no_vb2 = 1
#disp/wp_no_spo = 1
rdisp/wp_no_dia = 12
rdisp/wp_no_vb = 3
rdisp/wp_no_vb2 = 0
rdisp/wp_no_enq = 1
rdisp/wp_no_btc = 3
rdisp/wp_no_spo = 1
#PERFORMANS PARAMETRELERI
#parameter created                          by: SAP*         08.08.2001 10:30:18
abap/fieldexit = yes
#parameter created                          by: ALPER        13.10.2000 18:24:16
install/collate/active = 1
rdisp/max_wprun_time = 25000
MEMORY_NO_MORE_PAGING dump nedeniyle
#parameter created                          by: BASIS        27.12.2006 17:00:22
rdisp/PG_MAXFS = 262144
abap/heap_area_nondia = 2000000000
rdisp/PG_SHM = 16384
rdisp/ROLL_SHM = 32768
#'STORAGE_PARAMETERS_WRONG_SET' or 'TSV_TNEW_PAGE_ALLOC_FAILED'
#Note 552209 - Maximum memory utilization for processes on NT/Win2000
#parameter created                          by: BASIS        30.10.2007 10:57:24
#abap/heap_area_nondia = 50000
#parameter created                          by: BASIS        30.10.2007 10:58:54
#rdisp/PG_SHM = 0
#parameter created                          by: BASIS        30.10.2007 10:58:27
#rdisp/ROLL_SHM = 625
#EWA report 12.2007
#parameter created                          by: BASIS        03.01.2008 19:49:57
dbs/mss/stats_on = 1
#EWA report 12.2007
#parameter created                          by: BASIS        03.01.2008 19:49:33
dbs/oledb/stats_on = 1
#EWA report 12.2007
#parameter created                          by: BASIS        03.01.2008 19:48:23
dbs/oledb/add_procs = 8
#EWA report 12.2007
#parameter created                          by: BASIS        03.01.2008 19:47:29
rsdb/esm/max_objects = 2000
#EWA report 12.2007
#parameter created                          by: BASIS        03.01.2008 19:47:03
rsdb/otr/buffersize_kb = 4096
#EWA report 12.2007
#parameter created                          by: BASIS        03.01.2008 19:46:21
rsdb/esm/buffersize_kb = 4096
Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:18:14
ztta/parameter_area = 16000
Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:16:43
enque/table_size = 10000
Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:16:20
gw/max_sys = 2000
#Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:16:01
gw/max_overflow_size = 25000000
#Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:15:19
rdisp/max_comm_entries = 2000
Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:14:48
rdisp/tm_max_no = 2000
Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:14:20
gw/max_conn = 2000
Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:13:42
rdisp/max_arq = 2000
#Eyl#l 2006 EWA raporu
#parameter created                          by: BASIS        24.11.2006 13:12:57
ztta/roll_area = 3500000
#parameter created                          by: BASIS        18.05.2005 09:20:25
#old_value: 90                                changed: BASIS 18.05.2005 09:22:25
rdisp/max_hold_time = 300
#parameter created                          by: BASIS        20.08.2003 12:10:20
#old_value: 6144
#changed: BASIS         03.01.2008 19:42:10
rsdb/obj/buffersize = 20000
#parameter created                          by: BASIS        20.08.2003 12:09:48
#old_value: 6000
#changed: BASIS         03.01.2008 19:42:59
rsdb/obj/max_objects = 20000
note 103747
#parameter created                          by: BASIS        08.07.2003 20:42:11
#old_value: 250000
#changed: BASIS         30.10.2007 10:56:17
#abap/buffersize = 100000
#changed: BASIS         03.01.2008 19:40:36
#abap/buffersize = 300000
#by: BASIS 12.06.2008
abap/buffersize = 400000
note 103747
#parameter created                          by: BASIS        08.07.2003 20:41:32
#zcsa/presentation_buffer_area = 20000000
#64 bite gectikten sonra   by: BASIS 10.06.2008
zcsa/presentation_buffer_area = 30000768
note 103747
#parameter created                          by: BASIS        08.07.2003 20:40:55
rsdb/ntab/ftabsize = 30000
note 103747
#parameter created                          by: BASIS        08.07.2003 20:40:12
rtbb/max_tables = 500
note 103747
#parameter created                          by: BASIS        08.07.2003 20:39:15
#old_value: 20000
#changed: BASIS         03.01.2008 19:41:29
#rtbb/buffer_length = 30000
#64 bite gectikten sonra by: BASIS 10.06.2008
rtbb/buffer_length = 50000
note 103747
#parameter created                          by: BASIS        08.07.2003 20:38:26
zcsa/db_max_buftab = 10000
note 103747
#parameter created                          by: BASIS        08.07.2003 20:37:37
#zcsa/table_buffer_area = 50000000
#64 bite gectikten sonra   by: BASIS 10.06.2008
#zcsa/table_buffer_area = 89000000
by: BASIS 12.06.08
zcsa/table_buffer_area = 99000000
note 103747
#parameter created                          by: BASIS        08.07.2003 20:36:54
sap/bufdir_entries = 10000
note 103747
#parameter created                          by: BASIS        08.07.2003 20:36:12
rsdb/cua/buffersize = 8000
#note 103747
#parameter created                          by: BASIS        08.07.2003 20:34:46
#old_value: 5000                              changed: BASIS 08.07.2003 20:35:39
rsdb/ntab/sntabsize = 5500
#parameter created                          by: BASIS        08.07.2003 20:33:56
#note 103747
#old_value: 10607                             changed: BASIS 08.07.2003 20:34:58
#old_value: 10000                             changed: BASIS 08.07.2003 20:35:39
rsdb/ntab/irbdsize = 11000
#note 103747
#parameter created                          by: BASIS        08.07.2003 20:32:18
rsdb/ntab/entrycount = 40000
#old_value: 2076                              changed: BASIS 28.06.2005 19:36:21
#old_value: 5735                              changed: BASIS 28.06.2005 19:40:01
PHYS_MEMSIZE = 4096
#64 bite gectikten sonra   by: BASIS 10.06.2008
abap/heaplimit = 40894464
abap/heap_area_total = 2000683008
ztta/roll_extension = 2000683008
em/blocksize_KB = 4096
   *** UPGRADE EXTENSIONS (RELEASE "701") ***
#rdisp/elem_per_queue = 2000
#auth/auth_number_in_userbuffer = 9000
#snc/enable = 0

Hi Srikishan;
You are right. The problem was releated with secstore. I found a SAP note ( Note 1532825 - Deleting SECSTORE entries during system export/system copy). I created the program which ise mentioned in the note and than run it. After that everything seems ok now.
Thanks for your help and interest
Best regards
Noyan

Text/html processing error with Acrobat Reader when sending to database

Hi everyone,
I have a problem that occurs in certain versions of the Acrobat Reader, with Acrobat Professional the error message does not pop up.
In Acrobat Reader however, when sending the form to a php file to fill a database an error pops up
"Content type text/html couldn´t be processed"
Nevertheless it works fine, except the fact that the confirmation "successfully sent" that should pop up (and does in Acrobat Professional) does not appear due to this processing error. What can I do?
Thanks for supporting!

Hi,
I'll only attempt the first part:
See this discussion where event.target.path.toString().substring(0, 4); was used to get the first four letters of the path. If that equalled "http", then the form was opened in a browser.
http://forums.adobe.com/message/2840942#2840942
I can't contribute on the other issues.
Niall

I bought mountain lion en app stores and start download, but stops and mentioned is incomplete. and when start installation mentioned error because download is incomplete and send me to download again but the button is in "downloaded" what can i do?

I bought mountain lion en app stores and start download, but stops and mentioned is incomplete. and when start installation mentioned error because download is incomplete and send me to download again but the button is in "downloaded" what can i do?

Welcome to the support forums.
Please ask this question in the Mac App Store forum where they can better assist you.

Error 54 in udp write when sending to ip 127.0.0.1 !

Similar Messages

Maybe you are looking for