FIFO Problem
Hi Guys,
I am currently trying to acquire voltage and current measurement data
from an Analog Input Module 9201. The intention is to sample at 20kHz. I
am using a Compact RIO 9022 with a 9113 chassis. I know I need to
create a FIFO as a buffer between the FPGA and real time controller. The
FIFO created in the project is a Target to Host -DMA (im assuming this
is correct) with 12000 elements and a data type of FXP, signed 16 bits.
In my FPGA VI, I set the loop to execute every 50us each time gathering
1000 samples from each of the 6 channels.
For testing purposes, I am currently using a signal generator to generate a pure sine wave of 50Hz with an amplitude of 5.
On my Real Time VI, im not sure if I configured the FIFO correctly. I
used an Invoke Method to configure a FIFO with a depth of 40000. The VI
loops at 100ms, each time acquiring 6000 samples ( 6*1000) of data.
When I view the graph FIFO tester, the results were erratic, with
moments of it showing a badly sampled stepped sine wave.
Also, I am intending to phase shift the signal using the Fourier
based phase shifter shown in my VI. Instead of only phase shifting it,
the signal is offset as well. I am not sure what is the problem with
this part. I tried using a Hilbert Transform phase shifter ending up
with the same problem as well.
Would really appreciate if I could get some help regarding this matter.
Thanks
Attachments:
Analog Input (FPGA).vi 36 KB
Analog Input (Host).vi 568 KB
Ok, maybe we are dealing with a problem due to the size of the elements, but before we investigate that:
I have seen this exact sort of behaviour when not closing the reference to an FPGA target correctly. The following part of the example VIs is very important, as it closes down the reference to and release the resources related to the FPGA target.
To close down a reference that has been left open, instead of restarting your PC and cRIO, you can usually run a VI which contains just this piece of code directed toward your FPGA target.
Because it's so important to close down the FPGA reference then we must always stop running out code using stop buttons and data flow, coming naturally to the end of our code. The red button in LabVIEW, the "abort button" , should only ever be used to escape the very worst hangs or crashes as a last resort.
Let me know if this helps. Thanks
Rhys
Applications Engineer
National Instruments
Similar Messages
-
FIFO based pricing issue on sales orders!
This is the situations :
All setups in the comany are for FIFO. Item Level, Item Group Level, and Company Level.
1. We purchased 1 item1 for 125 dollars. PO invoice completed. First one in FIFO layer.
2. purchased 1 more of same item1 for 150 dollars. PO Invoice completed. Second in FIFO layer.
3. We want to sell above items to Customer1. Customer1 has price list set to - Last Evaluated Price.
4. Ran Inventory Audit Report to update the price list LastEvaluatedPrice.
5. Start order for Customer1 and add 1 item1 to order -
Price = 125 <== OK.
Make the above quantity 2 or add another line for item1.
Error : Price=125 <=== NOT OK, should be 125 for first item and 125 for second item (same item).
6. Run Audit Report again and repeat step 5.
Error : No change. Same as step results. That is price=125 instead of 150.
NOTE: Customer could end up in loss based on above pricing.
7. Yes there are workarounds :
7.1 Run Inventory Valuation Report for the item with MovingAverage as the price. Then the evaluated price is right.
7.2 Right click or run a query and get the price in layers and then calculate your own.
Note: No workarounds are good for customer. They and their staff do no want to open additional windows or run queries etc.
QUESTION: Why is FIFO pricing not working for Sales Order?
Note: Why would anyone use FIFO? It could give them big loss or big profits all unintended?
Please help? Is this FIFO problem, or my setup problem or something I do not understand?
Thanks and Cheers!Hi Syed,
Open sales order select that item and right click in unit price column and select "last prices" option. Then Last prices form will open just deselect BP Code check box and select vendor. you can see there prices in detail level just double click on row which price you want.
Thanks
Sachin -
How to enforce a static stream to be implemented using LUTRAM
Hi,
My design has a lot of internal static stream variables and most of them are with depth 4 to 16. However, I found that in the HDL generated by HLS, all the FIFOs are forced to be implemented with block ram. I tried to use
#pragma HLS RESOURCE variable=fs2fgFixMsg core=RAM_2P_LUTRAM
and
#pragma HLS RESOURCE variable=fs2fgFixMsg core=FIFO_LUTRAM
but that doesn't make any difference. Is there any way to force it or hopefully set a threshold value so that any depth less than that will be implemented with LUTRAM? Any help will be highly appreciated.
Best Regards,
Jimmyjust realized I am putting the pragma to the wrong fifos, problem solved. Sorry for that.
-
Fifo communication problem shifted data
Hello,
Currently,
there is a communication between a laptop, equiped with a NI cardbus 8310,
and a FPGA module controlling an industrial device.
However, we have to transfer this program to a more efficient computer.
The data transfered to the FPGA is sent thanks to a FIFO protocol.
Unfortunately, we met several communication problems while using the main program and the FPGA program :
- We have several error messages such as :
-52007
(The most recurrent) : "Called another software component" which
happens when we would like to run the FPGA program and when we stop the
main program.
61046 : a clock error which occurs at close FPGA VI reference.
We tried to solve these problems by creating a small program (without
the FIFO protocol) aiming to test the communication between the
powerfull computer and the FPGA. It worked.
- Then, we created
a program (on the computer) including the FIFO communication to test with the FPGA program. It
roughly worked but the data were shifted. (This program runs on the
laptop but not on the computer)
- Then, we created a
new project just to test the communication. It's a simple program in the
FPGA : when we click on OK button, it increments variables and
transmits them to the host. In the host.vi, when we valid a button, we
say to the FPGA "OK button = true" thus enabling reading of the data
from the FPGA. This program has the same FIFO method as the main program
but it doesn't work. Actually, in debug mode, we can see variables
incrementation but in real time mode, the program blocks in FIFO
reading.
- We would like to mention that we have two versions of Labview : labview v8.6 on the laptop and labview 2009 on the computer.
Hoping that you will be able to help us,
PS : in all test programs, we used the same way to implement the FIFO such as the first program which works on the laptop with labview v8.6.hello,
Thank you for your answer,
I understand your answer but the problem we have refers to the fifo. In fact, the program runs well on a laptop
but when we run it on another computer, the data from fifo are shifted. We don't understand why?
Morevover, we did another program with fifo communication and the program blocked during the fifo reading
and we just stop it with the abort program button. Do you know why?
We tested the FPGA program with the simulation and it worked normally.
Best regrads
Mathieu -
(solved)screen problem "reopen fifo blabla: no such file or directory"
i cant start screen. it just says "reopen fifo /tmp/screens/S-ramoneur/<random number>.pts-1.arch: no such file or directory"
ive searched google but cant find anything.
ive looked and the folder is there, the permissions is right, and yes i have free space on my /tmp.
i remember having a similiar problem to this before, and solved it just by doing screen -wipe. that doesnt work now.
it seems screen just cant create the file "/tmp/screens/S-ramoneur/<random number>.pts-1.arch" which is weird.
screen has worked perfectly before and i have a fully functioning config which ive used a long time.
anyone know whats wrong?
Last edited by ramoneur (2007-10-05 11:08:36)ah i figured it out now, i was looking for a script that would show my current ram usage in my hardstatus line, which i totally forgot i put in my .screenrc some hours ago. guess i havent started a new screen session since then
well the script obviously fucked everything up xD
does anyone know a simple script that will show my total available ram, and free ram in my hardstatus line?
it doesnt hurt asking one more question i hope...
i want my harddrives info (available gb and free gb) displayed in my hardstatus line aswell
Last edited by ramoneur (2007-10-05 00:33:17) -
Hold time problems with Dual Clock FIFO
Undoubtedly the main use-case for Dual Clock FIFOs is the transport of data across clock domains.
In this simple example, a serial datastream is deserialized and written to a dual clock FIFO, which in turn is read in a different (slightly faster) clock domain by a simple loopback unit, which takes the data and sends it back through another dual clock FIFO, where it is read and serialized out again.
The clock rates used are relatively slow (10Mhz and 12MHz) compared to the FPGA capabilities (both fabric and FIFO), so I would expect this to be straight forward and without any issues. Nevertheless, Vivado constantly creates a number of hold time violations on the input of the output FIFO (usually a few hundred picoseconds) where the routing delay seems to be in the range of 5ns, which I consider odd, given that both clocks have a period which is a magnitude higher.
The loopback should be synchronous with one clock cycle delay, so I wouldn't expect any problems from there.
As usual, I'm probably missing the obvious here and I'm looking forward to a great explanation what I did wrong :)
Thanks in advance,
HerbertHere is the Timing Report.
The issue might be caused by the Quick directive given for place and route.
place_design -directive Quick
route_design -directive Quick
At least the hold time violations in this example go away when I remove the directive.
Thanks for looking into it, appreciated!
Best,
Herbert -
Hello all, I've run into a bit of a problem using DMA FIFO to pass data to my RT host and I'm hoping someone might be able to see where I'm going wrong. I'm using a cRIO-9002/9102 chassis with NI 9217 RTD modules. I've attached my FPGA VI for reference. I've set up 2 target-host DMA FIFOs, one for grabbing my module calibration values and one for passing the actual RTD values. The first is set (right now) for 15 elements (only need 8 at the moment), and the second for 7 (only need 4 at the moment). FIFO 1 is running on DMA channel 0 and FIFO 2 is running on DMA channel 1. As far as I can tell, I've set everything up correctly, but I have two problems. First, everything seems to run just fine when I'm only passing 8 values to my 15 element FIFO, or 4 to my 7 element FIFO, but eventually I'm going to want to do a bit more dynamic data transfers and make use of the FIFO Full flag, which doesn't appear to work at the moment. I've padded my first data array with 8 zeros, so I'm trying to pass 16 elements to a 15 element FIFO, and the FIFO Full never trips to True, and my VI hangs right there...any idea what I've done wrong here? The second question is that in my host VI, when I read the 8 elements from the FIFO (normal operation, just 8 elements and no padded zeros) I use an unbundle to break out all the individual values. The problem is that the unbundle is sizing itself to 9 elements instead of 8 and I'm not sure why...is this something to do with the 0 based indexing of the FIFO? I'd thought that the 'Number of Elements' on the FIFO Read block was the total number but maybe its the index to read up to? Any help would be greatly appreciated.
Thanks,
-Greg
Attachments:
RTDAcq-FPGA.vi 103 KBHi Greg-
I'm glad the info helped. As far as using index array and decimate array, there are cases where each makes sense. If you only need a single sample of data such as when you are reading your Cal Data FIFO, the index array makes the most sense. The index array lets you index out more than one point at a time, so you shouldn't need a loop. Just grow it to pull out the data you need - in your case, it looks like you are writing 8 elements of Cal data (or 16 if you keep the padding with zeros at the end), so you could just grow your index array to look like the following
Note it is not necessary to have inputs on the left-hand side. By default it starts at index 0 and continues in order (1, 2, 3, etc.).
If you are looking more for a buffer of data, decimate array can be very useful. It takes the one large array and divides it back out to several small arrays. So you could read 1000 points from your RTD Data FIFO (250 samples per channel) and decimate it out to 4 arrays, 1 for each channel. Again, it is a growable structure so just make it match the number of channels you are pushing in on the FPGA side:
-Dustin
Message Edited by Dustin W on 11-15-2007 09:34 AM
Attachments:
Decimate Array.JPG 3 KB
Index Array.JPG 3 KB -
Problem in automatically clear open items on FIFO basis
Hi all
My requirement is like that I want to automatically clear open items on FIFO basis with only one condition on Customer Code should be match.
Is there is standard program or BAPI for that except sapf124(f.13). Or I have to write a new program . Because my configuration does not allow me to do so by SAPF124(f.13).
Thanks in advance.Hi,
look here:
1)there's a documentation in se38
2) http://help.sap.com/saphelp_45b/helpdata/en/e9/cb8a85eb0011d184650000e8a6bfbe/content.htm
Andreas -
Vivado 2015_1 FIFO simulation problem
i generated distributed fifo.
in sim folder i have this file
the place this module - fifo_generator_v12_0
i cant find this module for simulation. i have a folder with that name but without a sumulation file.
in the simulation folder (of fifo generator v_12) i have only "fifo_genrator_vlog_beh" file.
how i can run this fifo simulation
Hi,
Check the below article http://www.xilinx.com/support/answers/61035.html
You can use the below command to report all IP files necessary for simulation
get_files -compile_order sources -used_in simulation -of_objects [get_files <IP_Name>.xci]
Thanks,
Deepika. -
Probleme mit dem Lesen von DMA FIFOs vom FPGA!
Attachments:
burstgen_digital_input_2emitter.zip 2288 KBHi, please do not post code without any comment!
Please provide some kind of description. thx
M. Brauner NIG -
Analog out DMA performance problems
I'm working on an open-source driver for m-series and e-series boards (http://www.comedi.org). I've discoved some performance problems doing dma to analog outputs that I can't resolve. In summary, dma transfers to the analog output of a PXI-6281 in a pxi crate being controlled through a mxi-4 connection (pxi-pci8336) are VERY slow. I'm talking 250k samples/sec slow. That's the maximum speed the dma controller can fill the board's analog output fifo from host memory. I've also got an older PXI-6713 in the same crate, and dma transfers to it are about 15 times faster (about 3.5M samples/sec). I did notice that clearing the dma burst enable bit in the mite chips channel control register caused the 6713 to slow way down to something comparable to the 6281 (about 500k samples/sec). Setting or clearing the burst enable bit had no effect on the speed of the 6289. Is there some special mojo that needs to be done to enable burst transfers on the 6289? Also, even the relatively speedy 6713 does dma transfers much slower than it should, since the pxi-pci8336 advertises 80MB/sec sustained transfer rates over mxi4. Can you provide any insight into this matter? I've already looked through the ddk, and a register level document describing the mite chip, and example code which had chipobjects for the mite and an analog input example.
By the way, dma transfers for analog input on the 6281 weren't as bad, I didn't measure the transfer time, but I was at least able to do input at 500k samples/sec without fifo overruns.
I'll post more detailed performance measurements in a subsequent post, and include measurements for a couple other similar pci boards (a pci-6289 and pci-6711). In case you're wondering, neither of the pci boards get anywhere close to the bandwidth provided by the pci bus, but they're not as spectacularly bad as the pxi-6281.Here are my measurements:
PCI-6711, tested on 1.4GHz Pentium 4:
5.2 to 5.3 milliseconds to load fifo to half-full using dma. 0.9 to 1.0 microseconds to write to a 16-bit register. 1.9 to 2.1 microseconds to read from a 16-bit register. The mite's burst enable bit has no effect.
PXI-6713, tested on 3.2GHz Pentium D:
2.2 to 2.4 milliseconds to load fifo to half-full using dma. 0.5 to 0.7 microseconds to write to a 16-bit register. 5 to 7 microseconds to read from a 16-bit register. Turning off the mite's burst enable bit causes the dma fifo load time to increase to 16 to 17 milliseconds.
PCI-6289, tested on 3GHz Pentium 4:
2.0 to 2.2 milliseconds to load fifo to half-full using dma. 0.4 to 0.6 microseconds to write to a 16-bit register. About 1.2 microseconds to read from a 16-bit register. The mite's burst enable bit has no effect. I could do streaming analog output on 1 channel with an update rate of about 2.1MHz before the board's fifo started to underrun.
PXI-6281, tested on 3.2GHz Pentium D:
18 to 19 milliseconds to load fifo to half-full using dma. 0.3 to 0.4 microseconds to write to a 16-bit register. 4 to 6 microseconds to read from a 16-bit register. The mite's burst enable bit has no effect. I could do streaming analog output on 1 channel with an update rate of about 250kHz before the board's fifo started to underrun.
Notes: the 671x boards have a 16k sample ao fifo, the 628x boards have 8k.
The 4 to 7 microseconds times to read a register on the PXI boards seems large too, is that normal overhead for going over the mxi-4 connection?
I wasn't doing anything else intensive on the pci bus during these tests. For what it's worth, according to pci specs the two pci boards should be able to dma their analog output fifos to half full in less than 150 microseconds. -
System freezes due to hard disk problems only on Linux (not windows)
Intro/context:
Recently i've bought (about 2 months) a new laptop, a Lenovo G50-70, which came with Windows 8.1. As i had no interest on that OS, i formatted the disk and installed only Arch Linux. During that time i experienced system freezes which i had no idea why they were happening. As time went by, i found disk errors on system logs related to hard drive. I searched those errors and almost everything i found was that my hard drive had problems, so i decided to use my warranty. But first, i installed the original OS back again. And after using it a couple of weeks, i didn't experiencie any problem with my hard drive (on Linux it was really frequent). Now i've installed Arch Linux back, along with original Windows 8.1, having dual boot. There is no disk problem when using Windows, but when on Arch, i have the same errors and problems i used to have. So i assume it may be related to kernel or some confniguration issue.
I also haven't noticed any relation between system freezes and system use. I mean, it can happen either under light or heavy use.
tl dr: system freezes randomly for some minutes when using linux due to hard drive problems. The problem doesn't happen on windows.
What i've done so far:
The first period i was on Arch, i run smart (long and short), fsck, and hdparm tests. And nothing (no errors). Searched for bad blocks, and nothing. When back on windows, i also run tests on hdd and found no problems, except some sector reallocation not-that-nice indicators. These problems occured at the end of the first arch installation period. But still i currently experience no problem on windows.
I've also tried setting libata: noncq, 3.0G, noacpi, noapic kernel parameters, and had no result.
Changed BIOS setting from AHCI to Legacy, and no result. Also updated BIOS and no result.
I found no firmware update for this hard drive.
So i don't know what other thing i can try. I want to emphasize that there is no problem, no freezing, when running Windows, so i don't think it's a hard drive issue.
Info:
Hard drive is a Toshiba 2.5" HDD MQ01ABD100 5400 rpm.
Some logs i've recollected all this time:
journalctl -xfa --system
abr 21 13:51:13 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 13:51:24 echoes kernel: ata1.00: failed command: CHECK POWER MODE
abr 21 13:51:24 echoes kernel: ata1.00: cmd e5/00:00:00:00:00/00:00:00:00:00/00 tag 7
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 13:51:24 echoes kernel: ata1.00: status: { DRDY }
abr 21 13:51:24 echoes kernel: ata1: hard resetting link
abr 21 13:51:24 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 13:51:24 echoes kernel: ata1.00: configured for UDMA/100
abr 21 13:51:24 echoes kernel: ata1: EH complete
abr 21 14:01:40 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 14:02:01 echoes kernel: ata1.00: failed command: SMART
abr 21 14:02:01 echoes kernel: ata1.00: cmd b0/d1:01:00:4f:c2/00:00:00:00:00/00 tag 23 pio 512 in
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 14:02:01 echoes kernel: ata1.00: status: { DRDY }
abr 21 14:02:01 echoes kernel: ata1: hard resetting link
abr 21 14:02:01 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 14:02:01 echoes kernel: ata1.00: configured for UDMA/100
abr 21 14:02:01 echoes kernel: ata1: EH complete
abr 21 14:02:01 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 14:02:01 echoes kernel: ata1.00: failed command: SMART
abr 21 14:02:01 echoes kernel: ata1.00: cmd b0/d0:01:00:4f:c2/00:00:00:00:00/00 tag 22 pio 512 in
res 40/00:ff:ff:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 14:02:01 echoes kernel: ata1.00: status: { DRDY }
abr 21 14:02:01 echoes kernel: ata1: hard resetting link
abr 21 14:02:01 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 14:02:01 echoes kernel: ata1.00: configured for UDMA/100
abr 21 14:02:01 echoes kernel: ata1: EH complete
abr 21 14:02:01 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 21 14:02:01 echoes kernel: ata1.00: failed command: SMART
abr 21 14:02:01 echoes kernel: ata1.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 18
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 21 14:02:01 echoes kernel: ata1.00: status: { DRDY }
abr 21 14:02:01 echoes kernel: ata1: hard resetting link
abr 21 14:02:01 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 21 14:02:01 echoes kernel: ata1.00: configured for UDMA/100
abr 21 14:02:01 echoes kernel: ata1: EH complete
abr 21 14:01:51 echoes udisksd[627]: Error performing housekeeping for drive /org/freedesktop/UDisks2/drives/TOSHIBA_MQ01ABD100_Y44MT611T: Error updating SMART data: sk_disk_smart_status: Input/output error (udisks-error-quark, 0)
dmesg
[55661.023028] ata1.00: exception Emask 0x0 SAct 0x8000 SErr 0x0 action 0x6 frozen
[55661.023034] ata1.00: failed command: READ FPDMA QUEUED
[55661.023040] ata1.00: cmd 60/08:78:18:08:c0/00:00:4b:00:00/40 tag 15 ncq 4096 in
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[55661.023042] ata1.00: status: { DRDY }
[55661.023046] ata1: hard resetting link
[55666.358537] ata1: link is slow to respond, please be patient (ready=0)
[55671.053813] ata1: COMRESET failed (errno=-16)
[55671.053819] ata1: hard resetting link
[55676.389438] ata1: link is slow to respond, please be patient (ready=0)
[55678.897149] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[55681.320305] ata1.00: configured for UDMA/100
[55681.320319] ata1.00: device reported invalid CHS sector 0
[55681.320349] ata1: EH complete
[55729.969443] [drm:intel_set_cpu_fifo_underrun_reporting [i915]] *ERROR* uncleared fifo underrun on pipe A
[55729.969588] [drm:intel_cpu_fifo_underrun_irq_handler [i915]] *ERROR* CPU pipe A FIFO underrun
dmesg
[102884.889930] systemd[1]: systemd-journald.service: main process exited, code=dumped, status=6/ABRT
[102884.890305] systemd[1]: Unit systemd-journald.service entered failed state.
[102884.890333] systemd[1]: systemd-journald.service failed.
[102885.560745] systemd-coredump[28916]: Detected coredump of the journal daemon itself, diverted to /var/lib/systemd/coredump/core.systemd-journal.0.5bf9a012fed048ce8975998cf3c3c20e.6705.1427990901000000.
[102885.860957] systemd-journald[28919]: File /var/log/journal/b130c96d1371445d9ddeb40c51c77dd6/system.journal corrupted or uncleanly shut down, renaming and replacing.
[102921.797810] systemd-journald[28919]: File /var/log/journal/b130c96d1371445d9ddeb40c51c77dd6/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[104179.117363] ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
[104179.117369] ata1.00: failed command: READ FPDMA QUEUED
[104179.117375] ata1.00: cmd 60/08:00:48:88:8b/00:00:4d:00:00/40 tag 0 ncq 4096 in
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[104179.117377] ata1.00: status: { DRDY }
[104179.117381] ata1: hard resetting link
[104184.453382] ata1: link is slow to respond, please be patient (ready=0)
[104189.149114] ata1: COMRESET failed (errno=-16)
[104189.149121] ata1: hard resetting link
[104189.469276] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[104189.952982] ata1.00: configured for UDMA/100
[104189.952989] ata1.00: device reported invalid CHS sector 0
[104189.953004] ata1: EH complete
[104508.223792] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[104508.223798] ata1.00: failed command: SMART
[104508.223803] ata1.00: cmd b0/da:00:00:4f:c2/00:00:00:00:00/00 tag 2
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[104508.223806] ata1.00: status: { DRDY }
[104508.223810] ata1: hard resetting link
[104509.984601] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[104510.698126] ata1.00: configured for UDMA/100
[104510.698157] ata1: EH complete
One of the latest and worse
journalctl -xfa --system
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:00:e0:d6:75/00:00:00:00:00/40 tag 0 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:08:08:d8:75/00:00:00:00:00/40 tag 1 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:10:30:d9:75/00:00:00:00:00/40 tag 2 ncq 4096 out
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:18:58:da:75/00:00:00:00:00/40 tag 3 ncq 4096 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:20:e8:e5:75/00:00:00:00:00/40 tag 4 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:28:80:db:75/00:00:00:00:00/40 tag 5 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:30:68:dd:75/00:00:00:00:00/40 tag 6 ncq 4096 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:38:90:de:75/00:00:00:00:00/40 tag 7 ncq 4096 out
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:40:b8:df:75/00:00:00:00:00/40 tag 8 ncq 4096 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:48:90:e1:75/00:00:00:00:00/40 tag 9 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:50:98:e3:75/00:00:00:00:00/40 tag 10 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:58:c0:e4:75/00:00:00:00:00/40 tag 11 ncq 4096 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/c8:78:28:b9:2a/0b:00:4e:00:00/40 tag 15 ncq 1544192 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:80:b0:4b:c0/00:00:4f:00:00/40 tag 16 ncq 4096 out
res 40/00:ff:80:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/10:88:90:4b:80/00:00:50:00:00/40 tag 17 ncq 8192 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:90:98:22:81/00:00:50:00:00/40 tag 18 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:98:00:0e:00/00:00:5f:00:00/40 tag 19 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:a0:00:08:80/00:00:5f:00:00/40 tag 20 ncq 4096 out
res 40/00:ff:ff:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:a8:80:08:80/00:00:5f:00:00/40 tag 21 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/10:b0:08:0b:81/00:00:5f:00:00/40 tag 22 ncq 8192 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:b8:70:c8:75/00:00:00:00:00/40 tag 23 ncq 4096 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:c0:20:c9:75/00:00:00:00:00/40 tag 24 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:c8:88:c9:75/00:00:00:00:00/40 tag 25 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:d0:58:ca:75/00:00:00:00:00/40 tag 26 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:d8:a0:ce:75/00:00:00:00:00/40 tag 27 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:e0:68:d3:75/00:00:00:00:00/40 tag 28 ncq 4096 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:e8:90:d4:75/00:00:00:00:00/40 tag 29 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1.00: failed command: WRITE FPDMA QUEUED
abr 22 12:57:11 echoes kernel: ata1.00: cmd 61/08:f0:b8:d5:75/00:00:00:00:00/40 tag 30 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 22 12:57:11 echoes kernel: ata1.00: configured for UDMA/100
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: ata1.00: device reported invalid CHS sector 0
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x06
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] CDB:
abr 22 12:57:11 echoes kernel: cdb[0]=0x2a: 2a 00 12 88 d7 c0 00 04 d0 00
abr 22 12:57:11 echoes kernel: blk_update_request: I/O error, dev sda, sector 310958016
abr 22 12:57:11 echoes kernel: EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error -5 writing to inode 36311758 (offset 8388608 size 2695168 starting block 38869906)
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995128
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995129
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995130
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995131
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995132
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995133
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995134
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995135
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995136
abr 22 12:57:11 echoes kernel: Buffer I/O error on device sda2, logical block 19995137
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x06
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] CDB:
abr 22 12:57:11 echoes kernel: cdb[0]=0x2a: 2a 00 4b dd 39 88 00 01 78 00
abr 22 12:57:11 echoes kernel: blk_update_request: I/O error, dev sda, sector 1272789384
abr 22 12:57:11 echoes kernel: EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error -5 writing to inode 34999445 (offset 0 size 192512 starting block 159098720)
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x06
abr 22 12:57:11 echoes kernel: sd 0:0:0:0: [sda] CDB:
abr 22 12:57:11 echoes kernel: cdb[0]=0x2a: 2a 00 4e 2a b3 e8 00 05 40 00
abr 22 12:57:11 echoes kernel: blk_update_request: I/O error, dev sda, sector 1311421416
abr 22 12:57:11 echoes kernel: EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error -5 writing to inode 35001016 (offset 0 size 2232320 starting block 163927845)
abr 22 12:57:11 echoes kernel: ata1: EH complete
abr 22 12:57:11 echoes kernel: ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
abr 22 12:57:11 echoes kernel: ata1.00: failed command: CHECK POWER MODE
abr 22 12:57:11 echoes kernel: ata1.00: cmd e5/00:00:00:00:00/00:00:00:00:00/00 tag 25
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
abr 22 12:57:11 echoes kernel: ata1.00: status: { DRDY }
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: COMRESET failed (errno=-16)
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: COMRESET failed (errno=-16)
abr 22 12:57:11 echoes kernel: ata1: hard resetting link
abr 22 12:57:11 echoes kernel: ata1: link is slow to respond, please be patient (ready=0)
abr 22 12:57:11 echoes kernel: ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
abr 22 12:57:11 echoes kernel: ata1.00: configured for UDMA/100
abr 22 12:57:11 echoes kernel: ata1: EH complete
Current smart status:
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-4.0.1-1-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: Y44MT611T
LU WWN Device Id: 5 000039 5e1a80e85
Firmware Version: AX1P5E
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun May 3 16:42:06 2015 ART
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 234) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1671
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 306
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 152
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 699
10 Spin_Retry_Count 0x0033 106 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 300
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 216
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 14
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 14140
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 34 (Min/Max 16/44)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 19
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 099 099 000 Old_age Always - 515
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 190
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Vendor (0x50) Completed without error 00% 611 -
# 2 Short offline Completed without error 00% 611 -
# 3 Short offline Completed without error 00% 597 -
# 4 Vendor (0x50) Completed without error 00% 583 -
# 5 Short offline Completed without error 00% 583 -
# 6 Vendor (0x50) Completed without error 00% 575 -
# 7 Short offline Completed without error 00% 575 -
# 8 Short offline Completed without error 00% 547 -
# 9 Extended offline Completed without error 00% 529 -
#10 Short offline Completed without error 00% 355 -
#11 Short offline Completed without error 00% 355 -
#12 Extended offline Aborted by host 70% 355 -
#13 Short offline Completed without error 00% 319 -
#14 Vendor (0x50) Completed without error 00% 13 -
#15 Short offline Completed without error 00% 13 -
#16 Short offline Completed without error 00% 12 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Kernels used have been from 3.9 to current: Linux echoes 4.0.1-1-ARCH #1 SMP PREEMPT Wed Apr 29 12:00:26 CEST 2015 x86_64 GNU/Linux
Last edited by jesu (2015-05-03 19:42:53)Something i'd noticed both the first time i was on arch and now i've reinstalled it, was that at first i didn't have this problem. I mean, when Arch was just installed. While i was installing and setting up everything.
Now, i'm not 100% sure about this, but i think problems began when using my current user. Disk is partitioned the following way:
$ lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 931,5G 0 disk
├─sda1 8:1 0 1000M 0 part
├─sda2 8:2 0 260M 0 part /boot
├─sda3 8:3 0 207,7G 0 part
├─sda4 8:4 0 25G 0 part
├─sda5 8:5 0 14,8G 0 part
├─sda6 8:6 0 80,5G 0 part /
├─sda8 8:8 0 599G 0 part /home
└─sda9 8:9 0 2G 0 part [SWAP]
So, i believe problems, for some reason, are related (and were related), both before and now, to the /home partition, /dev/sda8 in this ocassion.
Because of this, i booted into systemd rescue mode, like root, rw, and unmounted /home partition. Despite root-only limitations, i used the system for a couple of hours, started lxqt, browsed the web mainly, and experienced no problem at all.
Now i booted normally, with my regular user, and these problems are experienced just like before (and almost instantly, like 3 or 5 minutes after starting system use).
dmesg this time showed a some different log, though it's not the first time i see this. I just didn't saved that kind of log before.
[ 653.821719] ata1.00: exception Emask 0x0 SAct 0x100 SErr 0x0 action 0x6 frozen
[ 653.821726] ata1.00: failed command: READ FPDMA QUEUED
[ 653.821732] ata1.00: cmd 60/08:40:60:25:43/00:00:1b:00:00/40 tag 8 ncq 4096 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 653.821735] ata1.00: status: { DRDY }
[ 653.821739] ata1: hard resetting link
[ 659.156760] ata1: link is slow to respond, please be patient (ready=0)
[ 663.851604] ata1: COMRESET failed (errno=-16)
[ 663.851610] ata1: hard resetting link
[ 669.186591] ata1: link is slow to respond, please be patient (ready=0)
[ 673.881456] ata1: COMRESET failed (errno=-16)
[ 673.881462] ata1: hard resetting link
[ 679.216481] ata1: link is slow to respond, please be patient (ready=0)
[ 702.743982] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 703.012578] ata1.00: configured for UDMA/100
[ 703.012584] ata1.00: device reported invalid CHS sector 0
[ 703.012599] ata1: EH complete
[ 714.097642] systemd[1]: systemd-journald.service watchdog timeout (limit 1min)!
[ 742.443488] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443494] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x2a 2a 00 28 c3 c6 40 00 00 10 00
[ 742.443497] blk_update_request: I/O error, dev sda, sector 683918912
[ 742.443503] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489866)
[ 742.443506] Buffer I/O error on device sda8, logical block 9323208
[ 742.443508] Buffer I/O error on device sda8, logical block 9323209
[ 742.443515] sd 0:0:0:0: [sda] tag#19 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443518] sd 0:0:0:0: [sda] tag#19 CDB: opcode=0x2a 2a 00 28 c3 c6 80 00 00 10 00
[ 742.443520] blk_update_request: I/O error, dev sda, sector 683918976
[ 742.443522] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489874)
[ 742.443524] Buffer I/O error on device sda8, logical block 9323216
[ 742.443526] Buffer I/O error on device sda8, logical block 9323217
[ 742.443531] sd 0:0:0:0: [sda] tag#20 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443534] sd 0:0:0:0: [sda] tag#20 CDB: opcode=0x2a 2a 00 28 c3 c6 d0 00 00 10 00
[ 742.443536] blk_update_request: I/O error, dev sda, sector 683919056
[ 742.443538] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489884)
[ 742.443540] Buffer I/O error on device sda8, logical block 9323226
[ 742.443542] Buffer I/O error on device sda8, logical block 9323227
[ 742.443547] sd 0:0:0:0: [sda] tag#21 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x06
[ 742.443549] sd 0:0:0:0: [sda] tag#21 CDB: opcode=0x2a 2a 00 28 c3 c7 10 00 00 10 00
[ 742.443551] blk_update_request: I/O error, dev sda, sector 683919120
[ 742.443553] EXT4-fs warning (device sda8): ext4_end_bio:317: I/O error -5 writing to inode 20322020 (offset 0 size 0 starting block 85489892)
[ 742.443555] Buffer I/O error on device sda8, logical block 9323234
[ 742.443557] Buffer I/O error on device sda8, logical block 9323235
[ 756.187685] systemd[1]: systemd-journald.service: main process exited, code=dumped, status=6/ABRT
[ 756.187986] systemd[1]: Unit systemd-journald.service entered failed state.
[ 756.188116] systemd[1]: systemd-journald.service failed.
[ 756.188474] systemd[1]: systemd-journald.service has no holdoff time, scheduling restart.
[ 756.189106] systemd[1]: Stopping Flush Journal to Persistent Storage...
[ 756.189143] systemd[1]: Listening on Journal Audit Socket.
[ 756.189801] systemd[1]: Starting Journal Service...
[ 757.525493] systemd-coredump[1038]: Detected coredump of the journal daemon itself, diverted to /var/lib/systemd/coredump/core.systemd-journal.0.b8610e85f9074a418534aaee0adbac56.141.1430763073000000.lz4.
[ 758.133944] systemd-journald[1050]: File /var/log/journal/f646626ba4b647f48501020bf12ca33b/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 758.503041] systemd[1]: Started Journal Service.
[ 759.180771] systemd-journald[1050]: File /var/log/journal/f646626ba4b647f48501020bf12ca33b/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[ 974.867721] ata1.00: exception Emask 0x0 SAct 0x3f80 SErr 0x0 action 0x6 frozen
[ 974.867732] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867742] ata1.00: cmd 61/08:38:68:d3:c5/00:00:1a:00:00/40 tag 7 ncq 4096 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867747] ata1.00: status: { DRDY }
[ 974.867751] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867759] ata1.00: cmd 61/08:40:88:d3:c5/00:00:1a:00:00/40 tag 8 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867763] ata1.00: status: { DRDY }
[ 974.867767] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867774] ata1.00: cmd 61/08:48:a0:d3:c5/00:00:1a:00:00/40 tag 9 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867778] ata1.00: status: { DRDY }
[ 974.867781] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867789] ata1.00: cmd 61/20:50:c0:d3:c5/00:00:1a:00:00/40 tag 10 ncq 16384 out
res 40/00:00:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867793] ata1.00: status: { DRDY }
[ 974.867796] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867803] ata1.00: cmd 61/10:58:f0:d3:c5/00:00:1a:00:00/40 tag 11 ncq 8192 out
res 40/00:01:00:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867807] ata1.00: status: { DRDY }
[ 974.867810] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867817] ata1.00: cmd 61/08:60:10:d4:c5/00:00:1a:00:00/40 tag 12 ncq 4096 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867821] ata1.00: status: { DRDY }
[ 974.867824] ata1.00: failed command: WRITE FPDMA QUEUED
[ 974.867831] ata1.00: cmd 61/18:68:28:d4:c5/00:00:1a:00:00/40 tag 13 ncq 12288 out
res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 974.867835] ata1.00: status: { DRDY }
[ 974.867841] ata1: hard resetting link
[ 980.202774] ata1: link is slow to respond, please be patient (ready=0)
[ 984.900902] ata1: COMRESET failed (errno=-16)
[ 984.900908] ata1: hard resetting link
[ 990.236024] ata1: link is slow to respond, please be patient (ready=0)
[ 994.930829] ata1: COMRESET failed (errno=-16)
[ 994.930836] ata1: hard resetting link
[ 996.798104] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 997.014012] ata1.00: configured for UDMA/100
[ 997.014020] ata1.00: device reported invalid CHS sector 0
[ 997.014023] ata1.00: device reported invalid CHS sector 0
[ 997.014025] ata1.00: device reported invalid CHS sector 0
[ 997.014026] ata1.00: device reported invalid CHS sector 0
[ 997.014028] ata1.00: device reported invalid CHS sector 0
[ 997.014030] ata1.00: device reported invalid CHS sector 0
[ 997.014031] ata1.00: device reported invalid CHS sector 0
[ 997.014065] ata1: EH complete
There are some sda8 (home) related messages. I also found these messages first time Arch was installed (i think also related to home partition).
root and home partitions are both ext4. -
Data has changed after passing through FIFO?
Dear experts,
I am currently working on a digital triangular shaping using the 7966R FPGA + 5734 AI. I am using LabView 2012 SP1.
Some days ago I have encountered a problem with my FIFOs that I have not been able to solve since. I'd be glad if somebody could point out a solution/ my error.
Short description:
I am writing U16 variables between ~32700-32800 to a U16 configured FIFO. The FIFO output does not coincide with the data I have been writing to the FIFO but is rather bit-shifted or something is added. This problem does not occure if I execute the VI on the dev. PC with simulated input.
What I have done so far:
I am reading all 4 channels of the 5734 inside a SCTL. The data is stored in 4 feedback nodes I am applying a triangular shaping to channel 0 and 1 by using 4 FIFOs that have been prefilled with a predefined number of zeros to serve as buffers. So it's something like (FB = Feedback node):
A I/O 1 --> FB --> FIFO 1 --> FB --> FIFO 2 --> FB --> Do something
A I/O 2 --> FB --> FIFO 3 --> FB --> FIFO 4 --> FB --> Do something
This code shows NO weird behaviour and works as expected.
The Problem:
To reduce the amount of FIFOs needed I then decided to interleave the data and to use only 2 FIFOs instead of 4. You can see the code in the attachment. As you can see I have not really changed anything to the code structure in general.
The input to the FIFO is a U16. All FIFOs are configured to store U16 data.
The data that I am writing to the FIFO can be seen in channel 0 of the output attachment.
The output after passing through the two FIFOs can be seen in channel 2 of the same picture.
The output after passing through the first FIFO (times 2) can be seen in channel 3 of the picture.
It looks like the output is bit-shifted and truncated as it enters Buffer 1. Yet the difference between the input and output is not exactly a factor of 2. I also considered the possibility that the FIFO adds both write operations (CH0 + CH1) but that also does not account for the value of the output.
The FIFOs are all operating normally, i.e. none throws a timeout. I also tried several different orders of reading/writing to the FIFOs and different ways of ensuring this order (i.e. case strucutres, flat and stacked sequence). The FIFOs are also large enough to store the amount of data buffered no matter if I write or read first.
Thank you very much,
Bjorn
Attachments:
FPGA-code.png 61 KB
FPGA-output.png 45 KBDuring the last couple of days I tried the following:
1. Running the FPGA code on the development PC with simulated I/O. The behavior was normal, i.e. like I've intended the code to perform.
2. I tested the code on the development PC with the square and sine wave generation VI as 'simulated' I/O. The code performed normal.
3. I replaced the FIFOs with queues and ran my logic on the dev. PC. The logic performed totally normal.
4. Right now the code is compiling with constants as inputs like you suggested...
I am currently trying to get LabView 2013 on the development machine. It seems like my last real hope is that the issue is a bug in the XILINX 13.4 compiler tools and that the 14.4 tools will just make it disappear...
Nevertheless I am still open for suggestions. Some additional info about my FIFOs of concerne:
Buffer 1 and 2:
- Type: Target Scoped
- Elements Requested: 1023
- Implementation: Block Memory
- Control Logic: Target Optimal
- Data Type: U16
- Arbitrate for Read: Never Arbitrate
- No. Elements Per Read: 1
- Arbitrate for Write: Never Arbitrate
- No. Elements Per Write: 1
The inputs from the NI 5734 are U16 so I am wirering the right data type to the FIFOs. I also don't have any coercion dots within my FPGA VI. And so far it has only occured after the VI has been compiled onto the FPGA. Could some of the FIFOs/block memory be corrupted because we have written stuff onto the FPGA too often? -
Hello, I'm not sure whether I'm posting in the correct section of the forums but anyway, here's the problem, after upgrading the system xfce started crashing randomly (It definitely crashes when I try to suspend first time, then it does it correctly). I took a look in Xorg and fglrx log files, they didn't contain any errors. However, dmesg listed a segfault of xfce4-session in libglib, is there any solution for that problem or I just have to wait until the upgrade. Also, I have and AMD E-450 APU, and a proprietary catalyst driver from catalyst-stable. Here is the output from dmesg (the segfault message is in the end):
[ 0.000000] PM: Registered nosave memory: 00000000afb64000 - 00000000afb6c000
[ 0.000000] PM: Registered nosave memory: 00000000afb6c000 - 00000000afb91000
[ 0.000000] PM: Registered nosave memory: 00000000afb91000 - 00000000afbd4000
[ 0.000000] PM: Registered nosave memory: 00000000afd47000 - 00000000afef7000
[ 0.000000] PM: Registered nosave memory: 00000000aff00000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fec10000
[ 0.000000] PM: Registered nosave memory: 00000000fec10000 - 00000000fec11000
[ 0.000000] PM: Registered nosave memory: 00000000fec11000 - 00000000fed00000
[ 0.000000] PM: Registered nosave memory: 00000000fed00000 - 00000000fed01000
[ 0.000000] PM: Registered nosave memory: 00000000fed01000 - 00000000fed61000
[ 0.000000] PM: Registered nosave memory: 00000000fed61000 - 00000000fed71000
[ 0.000000] PM: Registered nosave memory: 00000000fed71000 - 00000000fed80000
[ 0.000000] PM: Registered nosave memory: 00000000fed80000 - 00000000fed90000
[ 0.000000] PM: Registered nosave memory: 00000000fed90000 - 00000000fef00000
[ 0.000000] PM: Registered nosave memory: 00000000fef00000 - 0000000100000000
[ 0.000000] PM: Registered nosave memory: 0000000100000000 - 0000000100001000
[ 0.000000] e820: [mem 0xaff00000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88013fc00000 s84544 r8192 d21952 u1048576
[ 0.000000] pcpu-alloc: s84544 r8192 d21952 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 966665
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux-lqx root=UUID=ee58701b-54f4-4a5e-a884-636f3ac8cb2f ro nomodeset usbcore.autosuspend=1 quiet usbcore.autosuspend=0 nomodeset nmi_watchdog=0 pcie_aspm=force
[ 0.000000] PCIe ASPM is forcibly enabled
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3782720k/5242880k available (4438k kernel code, 1314812k absent, 145348k reserved, 2809k data, 640k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=2.
[ 0.000000] NR_IRQS:33024 nr_irqs:512 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.001000] tsc: Detected 1646.401 MHz processor
[ 0.000005] Calibrating delay loop (skipped), value calculated using timer frequency.. 3292.80 BogoMIPS (lpj=1646401)
[ 0.000010] pid_max: default: 32768 minimum: 301
[ 0.000063] Security Framework initialized
[ 0.000068] SELinux: Disabled at boot.
[ 0.000071] AppArmor: AppArmor disabled by boot time parameter
[ 0.000073] Yama: becoming mindful.
[ 0.000095] Mount-cache hash table entries: 256
[ 0.000418] tseg: 00aff00000
[ 0.000422] CPU: Physical Processor ID: 0
[ 0.000424] CPU: Processor Core ID: 0
[ 0.000426] mce: CPU supports 6 MCE banks
[ 0.000442] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4
tlb_flushall_shift: 5
[ 0.000558] Freeing SMP alternatives: 16k freed
[ 0.002455] ACPI: Core revision 20121018
[ 0.015032] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.025024] smpboot: CPU0: AMD E-450 APU with Radeon(tm) HD Graphics (fam: 14, model: 02, stepping: 00)
[ 0.126038] Performance Events: AMD PMU driver.
[ 0.126044] ... version: 0
[ 0.126047] ... bit width: 48
[ 0.126048] ... generic registers: 4
[ 0.126050] ... value mask: 0000ffffffffffff
[ 0.126051] ... max period: 00007fffffffffff
[ 0.126053] ... fixed-purpose events: 0
[ 0.126054] ... event mask: 000000000000000f
[ 0.134178] smpboot: Booting Node 0, Processors #1 OK
[ 0.147430] Brought up 2 CPUs
[ 0.147435] smpboot: Total of 2 processors activated (6585.60 BogoMIPS)
[ 0.148250] devtmpfs: initialized
[ 0.148666] PM: Registering ACPI NVS region [mem 0xafaf7000-0xafb3efff] (294912 bytes)
[ 0.148681] PM: Registering ACPI NVS region [mem 0xafb49000-0xafb4bfff] (12288 bytes)
[ 0.148683] PM: Registering ACPI NVS region [mem 0xafb4d000-0xafb4dfff] (4096 bytes)
[ 0.148686] PM: Registering ACPI NVS region [mem 0xafb64000-0xafb6bfff] (32768 bytes)
[ 0.148689] PM: Registering ACPI NVS region [mem 0xafb91000-0xafbd3fff] (274432 bytes)
[ 0.149151] regulator-dummy: no parameters
[ 0.149293] NET: Registered protocol family 16
[ 0.150271] ACPI: bus type pci registered
[ 0.150593] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.150599] PCI: not using MMCONFIG
[ 0.150601] PCI: Using configuration type 1 for base access
[ 0.150602] PCI: Using configuration type 1 for extended access
[ 0.155916] bio: create slab <bio-0> at 0
[ 0.156315] ACPI: Added _OSI(Module Device)
[ 0.156319] ACPI: Added _OSI(Processor Device)
[ 0.156321] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.156323] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.158103] ACPI: EC: Look up EC in DSDT
[ 0.160056] ACPI: Executed 3 blocks of module-level executable AML code
[ 0.172510] ACPI: Interpreter enabled
[ 0.172527] ACPI: (supports S0 S3 S4 S5)
[ 0.172576] ACPI: Using IOAPIC for interrupt routing
[ 0.172886] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.172961] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.213033] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.213391] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 0.245487] ACPI: EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62
[ 0.245850] ACPI: No dock devices found.
[ 0.245858] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.246163] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.246166] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.246887] PCI host bridge to bus 0000:00
[ 0.246895] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.246899] pci_bus 0000:00: root bus resource [io 0x0000-0x03af]
[ 0.246906] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7]
[ 0.246910] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df]
[ 0.246913] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.246916] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.246919] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[ 0.246923] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff]
[ 0.246938] pci 0000:00:00.0: [1022:1510] type 00 class 0x060000
[ 0.246999] pci 0000:00:01.0: [1002:9806] type 00 class 0x030000
[ 0.247013] pci 0000:00:01.0: reg 10: [mem 0xc0000000-0xcfffffff pref]
[ 0.247023] pci 0000:00:01.0: reg 14: [io 0xf000-0xf0ff]
[ 0.247032] pci 0000:00:01.0: reg 18: [mem 0xfeb00000-0xfeb3ffff]
[ 0.247093] pci 0000:00:01.0: supports D1 D2
[ 0.247118] pci 0000:00:01.1: [1002:1314] type 00 class 0x040300
[ 0.247130] pci 0000:00:01.1: reg 10: [mem 0xfeb44000-0xfeb47fff]
[ 0.247202] pci 0000:00:01.1: supports D1 D2
[ 0.247388] pci 0000:00:04.0: [1022:1512] type 01 class 0x060400
[ 0.247482] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.247576] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601
[ 0.247602] pci 0000:00:11.0: reg 10: [io 0xf140-0xf147]
[ 0.247615] pci 0000:00:11.0: reg 14: [io 0xf130-0xf133]
[ 0.247629] pci 0000:00:11.0: reg 18: [io 0xf120-0xf127]
[ 0.247642] pci 0000:00:11.0: reg 1c: [io 0xf110-0xf113]
[ 0.247655] pci 0000:00:11.0: reg 20: [io 0xf100-0xf10f]
[ 0.247669] pci 0000:00:11.0: reg 24: [mem 0xfeb4d000-0xfeb4d3ff]
[ 0.247749] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310
[ 0.247767] pci 0000:00:12.0: reg 10: [mem 0xfeb4c000-0xfeb4cfff]
[ 0.247863] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320
[ 0.247889] pci 0000:00:12.2: reg 10: [mem 0xfeb4b000-0xfeb4b0ff]
[ 0.247997] pci 0000:00:12.2: supports D1 D2
[ 0.248000] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.248033] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310
[ 0.248052] pci 0000:00:13.0: reg 10: [mem 0xfeb4a000-0xfeb4afff]
[ 0.248150] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320
[ 0.248175] pci 0000:00:13.2: reg 10: [mem 0xfeb49000-0xfeb490ff]
[ 0.248289] pci 0000:00:13.2: supports D1 D2
[ 0.248292] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.248325] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
[ 0.248433] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
[ 0.248461] pci 0000:00:14.2: reg 10: [mem 0xfeb40000-0xfeb43fff 64bit]
[ 0.248548] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.248571] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100
[ 0.248673] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
[ 0.248732] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310
[ 0.248750] pci 0000:00:14.5: reg 10: [mem 0xfeb48000-0xfeb48fff]
[ 0.248848] pci 0000:00:15.0: [1002:43a0] type 01 class 0x060400
[ 0.248953] pci 0000:00:15.0: supports D1 D2
[ 0.248991] pci 0000:00:15.1: [1002:43a1] type 01 class 0x060400
[ 0.249095] pci 0000:00:15.1: supports D1 D2
[ 0.249133] pci 0000:00:15.2: [1002:43a2] type 01 class 0x060400
[ 0.249237] pci 0000:00:15.2: supports D1 D2
[ 0.249282] pci 0000:00:15.3: [1002:43a3] type 01 class 0x060400
[ 0.249387] pci 0000:00:15.3: supports D1 D2
[ 0.249426] pci 0000:00:18.0: [1022:1700] type 00 class 0x060000
[ 0.249474] pci 0000:00:18.1: [1022:1701] type 00 class 0x060000
[ 0.249518] pci 0000:00:18.2: [1022:1702] type 00 class 0x060000
[ 0.249564] pci 0000:00:18.3: [1022:1703] type 00 class 0x060000
[ 0.249621] pci 0000:00:18.4: [1022:1704] type 00 class 0x060000
[ 0.249665] pci 0000:00:18.5: [1022:1718] type 00 class 0x060000
[ 0.249711] pci 0000:00:18.6: [1022:1716] type 00 class 0x060000
[ 0.249755] pci 0000:00:18.7: [1022:1719] type 00 class 0x060000
[ 0.249928] pci 0000:00:04.0: PCI bridge to [bus 01]
[ 0.250055] pci 0000:00:14.4: PCI bridge to [bus 02] (subtractive decode)
[ 0.250067] pci 0000:00:14.4: bridge window [io 0x0000-0x03af] (subtractive decode)
[ 0.250070] pci 0000:00:14.4: bridge window [io 0x03e0-0x0cf7] (subtractive decode)
[ 0.250074] pci 0000:00:14.4: bridge window [io 0x03b0-0x03df] (subtractive decode)
[ 0.250077] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.250080] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.250083] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.250086] pci 0000:00:14.4: bridge window [mem 0xc0000000-0xffffffff] (subtractive decode)
[ 0.250216] pci 0000:03:00.0: [14e4:4727] type 00 class 0x028000
[ 0.250259] pci 0000:03:00.0: reg 10: [mem 0xfea00000-0xfea03fff 64bit]
[ 0.250422] pci 0000:03:00.0: supports D1 D2
[ 0.250425] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.252383] pci 0000:00:15.0: PCI bridge to [bus 03]
[ 0.252400] pci 0000:00:15.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.252481] pci 0000:00:15.1: PCI bridge to [bus 04]
[ 0.252587] pci 0000:05:00.0: [10ec:8168] type 00 class 0x020000
[ 0.252610] pci 0000:05:00.0: reg 10: [io 0xe000-0xe0ff]
[ 0.252649] pci 0000:05:00.0: reg 18: [mem 0xd0004000-0xd0004fff 64bit pref]
[ 0.252674] pci 0000:05:00.0: reg 20: [mem 0xd0000000-0xd0003fff 64bit pref]
[ 0.252777] pci 0000:05:00.0: supports D1 D2
[ 0.252780] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.254339] pci 0000:00:15.2: PCI bridge to [bus 05]
[ 0.254353] pci 0000:00:15.2: bridge window [io 0xe000-0xefff]
[ 0.254369] pci 0000:00:15.2: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.254451] pci 0000:00:15.3: PCI bridge to [bus 06]
[ 0.254501] pci_bus 0000:00: on NUMA node 0
[ 0.254602] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE20._PRT]
[ 0.254674] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE21._PRT]
[ 0.254726] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE22._PRT]
[ 0.254777] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE23._PRT]
[ 0.254856] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
[ 0.254913] pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 0.254916] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 0.259554] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 11 14 15) *0
[ 0.259704] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 10 11 14 15) *0
[ 0.259814] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 11 14 15) *0
[ 0.259920] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 10 11 14 15) *0
[ 0.260007] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 14 15) *0
[ 0.260075] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 14 15) *0
[ 0.260142] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7 10 11 14 15) *0
[ 0.260210] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 14 15) *0
[ 0.260719] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.260732] vgaarb: loaded
[ 0.260733] vgaarb: bridge control possible 0000:00:01.0
[ 0.261239] ACPI: bus type usb registered
[ 0.261372] usbcore: registered new interface driver usbfs
[ 0.261438] usbcore: registered new interface driver hub
[ 0.261565] usbcore: registered new device driver usb
[ 0.262092] PCI: Using ACPI for IRQ routing
[ 0.273018] PCI: pci_cache_line_size set to 64 bytes
[ 0.273142] e820: reserve RAM buffer [mem 0x0009ec00-0x0009ffff]
[ 0.273146] e820: reserve RAM buffer [mem 0xafaf7000-0xafffffff]
[ 0.273149] e820: reserve RAM buffer [mem 0xafb54000-0xafffffff]
[ 0.273151] e820: reserve RAM buffer [mem 0xafd47000-0xafffffff]
[ 0.273154] e820: reserve RAM buffer [mem 0xaff00000-0xafffffff]
[ 0.273543] NetLabel: Initializing
[ 0.273546] NetLabel: domain hash size = 128
[ 0.273547] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.273565] NetLabel: unlabeled traffic allowed by default
[ 0.273680] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.273687] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.275723] Switching to clocksource hpet
[ 0.281493] pnp: PnP ACPI init
[ 0.281511] ACPI: bus type pnp registered
[ 0.281854] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.281861] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.282965] system 00:01: [io 0x040b] has been reserved
[ 0.282969] system 00:01: [io 0x04d6] has been reserved
[ 0.282972] system 00:01: [io 0x0c00-0x0c01] has been reserved
[ 0.282979] system 00:01: [io 0x0c14] has been reserved
[ 0.282984] system 00:01: [io 0x0c50-0x0c51] has been reserved
[ 0.282987] system 00:01: [io 0x0c52] has been reserved
[ 0.282990] system 00:01: [io 0x0c6c] has been reserved
[ 0.282994] system 00:01: [io 0x0c6f] has been reserved
[ 0.282997] system 00:01: [io 0x0cd0-0x0cd1] has been reserved
[ 0.283000] system 00:01: [io 0x0cd2-0x0cd3] has been reserved
[ 0.283004] system 00:01: [io 0x0cd4-0x0cd5] has been reserved
[ 0.283007] system 00:01: [io 0x0cd6-0x0cd7] has been reserved
[ 0.283010] system 00:01: [io 0x0cd8-0x0cdf] has been reserved
[ 0.283014] system 00:01: [io 0x0800-0x089f] has been reserved
[ 0.283017] system 00:01: [io 0x0b20-0x0b3f] has been reserved
[ 0.283020] system 00:01: [io 0x0900-0x090f] has been reserved
[ 0.283024] system 00:01: [io 0x0910-0x091f] has been reserved
[ 0.283027] system 00:01: [io 0xfe00-0xfefe] has been reserved
[ 0.283033] system 00:01: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.283037] system 00:01: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.283041] system 00:01: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 0.283045] system 00:01: [mem 0xfed61000-0xfed70fff] has been reserved
[ 0.283049] system 00:01: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.283054] system 00:01: [mem 0xfed00000-0xfed00fff] has been reserved
[ 0.283057] system 00:01: [mem 0xffe00000-0xffffffff] has been reserved
[ 0.283062] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.283085] pnp 00:02: [dma 4]
[ 0.283236] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.283356] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.283484] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.283686] system 00:05: [io 0x04d0-0x04d1] has been reserved
[ 0.283691] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.283937] pnp 00:06: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.284106] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.284264] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.284487] pnp 00:09: Plug and Play ACPI device, IDs ETD0b00 SYN0002 PNP0f13 (active)
[ 0.285108] system 00:0a: [mem 0xb0000000-0xbfffffff] has been reserved
[ 0.285113] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.297800] pnp 00:0b: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.297811] pnp: PnP ACPI: found 12 devices
[ 0.297813] ACPI: ACPI bus type pnp unregistered
[ 0.303106] pci 0000:00:04.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 0.303114] pci 0000:00:04.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 0.303119] pci 0000:00:04.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[ 0.303173] pci 0000:00:15.0: bridge window [io 0x1000-0x0fff] to [bus 03] add_size 1000
[ 0.303178] pci 0000:00:15.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000
[ 0.303192] pci 0000:00:15.1: bridge window [io 0x1000-0x0fff] to [bus 04] add_size 1000
[ 0.303196] pci 0000:00:15.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000
[ 0.303200] pci 0000:00:15.1: bridge window [mem 0x00100000-0x000fffff] to [bus 04] add_size 200000
[ 0.303213] pci 0000:00:15.2: bridge window [mem 0x00100000-0x000fffff] to [bus 05] add_size 400000
[ 0.303226] pci 0000:00:15.3: bridge window [io 0x1000-0x0fff] to [bus 06] add_size 1000
[ 0.303230] pci 0000:00:15.3: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 06] add_size 200000
[ 0.303234] pci 0000:00:15.3: bridge window [mem 0x00100000-0x000fffff] to [bus 06] add_size 200000
[ 0.303253] pci 0000:00:04.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.303257] pci 0000:00:04.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.303261] pci 0000:00:15.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.303264] pci 0000:00:15.1: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.303268] pci 0000:00:15.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.303271] pci 0000:00:15.2: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 400000
[ 0.303275] pci 0000:00:15.3: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.303278] pci 0000:00:15.3: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.303281] pci 0000:00:04.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.303285] pci 0000:00:15.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.303288] pci 0000:00:15.1: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.303291] pci 0000:00:15.3: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.303300] pci 0000:00:04.0: BAR 14: assigned [mem 0xd0100000-0xd02fffff]
[ 0.303305] pci 0000:00:04.0: BAR 15: assigned [mem 0xd0300000-0xd04fffff 64bit pref]
[ 0.303310] pci 0000:00:15.0: BAR 15: assigned [mem 0xd0500000-0xd06fffff 64bit pref]
[ 0.303315] pci 0000:00:15.1: BAR 14: assigned [mem 0xd0700000-0xd08fffff]
[ 0.303320] pci 0000:00:15.1: BAR 15: assigned [mem 0xd0900000-0xd0afffff 64bit pref]
[ 0.303324] pci 0000:00:15.2: BAR 14: assigned [mem 0xd0b00000-0xd0efffff]
[ 0.303328] pci 0000:00:15.3: BAR 14: assigned [mem 0xd0f00000-0xd10fffff]
[ 0.303332] pci 0000:00:15.3: BAR 15: assigned [mem 0xd1100000-0xd12fffff 64bit pref]
[ 0.303339] pci 0000:00:04.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.303345] pci 0000:00:15.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.303349] pci 0000:00:15.1: BAR 13: assigned [io 0x3000-0x3fff]
[ 0.303354] pci 0000:00:15.3: BAR 13: assigned [io 0x4000-0x4fff]
[ 0.303361] pci 0000:00:04.0: PCI bridge to [bus 01]
[ 0.303367] pci 0000:00:04.0: bridge window [io 0x1000-0x1fff]
[ 0.303373] pci 0000:00:04.0: bridge window [mem 0xd0100000-0xd02fffff]
[ 0.303378] pci 0000:00:04.0: bridge window [mem 0xd0300000-0xd04fffff 64bit pref]
[ 0.303385] pci 0000:00:14.4: PCI bridge to [bus 02]
[ 0.303470] pci 0000:00:15.0: PCI bridge to [bus 03]
[ 0.303474] pci 0000:00:15.0: bridge window [io 0x2000-0x2fff]
[ 0.303481] pci 0000:00:15.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.303487] pci 0000:00:15.0: bridge window [mem 0xd0500000-0xd06fffff 64bit pref]
[ 0.303495] pci 0000:00:15.1: PCI bridge to [bus 04]
[ 0.303499] pci 0000:00:15.1: bridge window [io 0x3000-0x3fff]
[ 0.303506] pci 0000:00:15.1: bridge window [mem 0xd0700000-0xd08fffff]
[ 0.303512] pci 0000:00:15.1: bridge window [mem 0xd0900000-0xd0afffff 64bit pref]
[ 0.303521] pci 0000:00:15.2: PCI bridge to [bus 05]
[ 0.303525] pci 0000:00:15.2: bridge window [io 0xe000-0xefff]
[ 0.303532] pci 0000:00:15.2: bridge window [mem 0xd0b00000-0xd0efffff]
[ 0.303537] pci 0000:00:15.2: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.303545] pci 0000:00:15.3: PCI bridge to [bus 06]
[ 0.303549] pci 0000:00:15.3: bridge window [io 0x4000-0x4fff]
[ 0.303557] pci 0000:00:15.3: bridge window [mem 0xd0f00000-0xd10fffff]
[ 0.303562] pci 0000:00:15.3: bridge window [mem 0xd1100000-0xd12fffff 64bit pref]
[ 0.303627] pci_bus 0000:00: resource 4 [io 0x0000-0x03af]
[ 0.303631] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7]
[ 0.303634] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df]
[ 0.303637] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff]
[ 0.303640] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
[ 0.303643] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff]
[ 0.303647] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xffffffff]
[ 0.303650] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
[ 0.303653] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd02fffff]
[ 0.303656] pci_bus 0000:01: resource 2 [mem 0xd0300000-0xd04fffff 64bit pref]
[ 0.303660] pci_bus 0000:02: resource 4 [io 0x0000-0x03af]
[ 0.303663] pci_bus 0000:02: resource 5 [io 0x03e0-0x0cf7]
[ 0.303666] pci_bus 0000:02: resource 6 [io 0x03b0-0x03df]
[ 0.303669] pci_bus 0000:02: resource 7 [io 0x0d00-0xffff]
[ 0.303672] pci_bus 0000:02: resource 8 [mem 0x000a0000-0x000bffff]
[ 0.303675] pci_bus 0000:02: resource 9 [mem 0x000c0000-0x000dffff]
[ 0.303678] pci_bus 0000:02: resource 10 [mem 0xc0000000-0xffffffff]
[ 0.303681] pci_bus 0000:03: resource 0 [io 0x2000-0x2fff]
[ 0.303684] pci_bus 0000:03: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.303687] pci_bus 0000:03: resource 2 [mem 0xd0500000-0xd06fffff 64bit pref]
[ 0.303691] pci_bus 0000:04: resource 0 [io 0x3000-0x3fff]
[ 0.303693] pci_bus 0000:04: resource 1 [mem 0xd0700000-0xd08fffff]
[ 0.303752] pci_bus 0000:04: resource 2 [mem 0xd0900000-0xd0afffff 64bit pref]
[ 0.303755] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.303758] pci_bus 0000:05: resource 1 [mem 0xd0b00000-0xd0efffff]
[ 0.303761] pci_bus 0000:05: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.303765] pci_bus 0000:06: resource 0 [io 0x4000-0x4fff]
[ 0.303768] pci_bus 0000:06: resource 1 [mem 0xd0f00000-0xd10fffff]
[ 0.303771] pci_bus 0000:06: resource 2 [mem 0xd1100000-0xd12fffff 64bit pref]
[ 0.303836] NET: Registered protocol family 2
[ 0.304049] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.304316] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.304574] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.304683] TCP: reno registered
[ 0.304693] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.304845] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.305013] NET: Registered protocol family 1
[ 0.305042] pci 0000:00:01.0: Boot video device
[ 0.305384] PCI: CLS 64 bytes, default 64
[ 0.305471] Unpacking initramfs...
[ 0.400016] Freeing initrd memory: 2664k freed
[ 0.401721] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.401733] software IO TLB [mem 0xabaf7000-0xafaf7000] (64MB) mapped at [ffff8800abaf7000-ffff8800afaf6fff]
[ 0.401984] LVT offset 0 assigned for vector 0x400
[ 0.402067] perf: AMD IBS detected (0x000000ff)
[ 0.402950] audit: initializing netlink socket (disabled)
[ 0.402971] type=2000 audit(1367137456.294:1): initialized
[ 0.403912] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.410965] VFS: Disk quotas dquot_6.5.2
[ 0.411207] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.411535] msgmni has been set to 7393
[ 0.412281] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.412285] io scheduler noop registered
[ 0.412287] io scheduler deadline registered
[ 0.412295] io scheduler cfq registered
[ 0.412435] io scheduler bfq registered (default)
[ 0.413822] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.415487] Linux agpgart interface v0.103
[ 0.415820] vesafb: mode is 1024x768x32, linelength=4096, pages=0
[ 0.415822] vesafb: scrolling: redraw
[ 0.415826] vesafb: Truecolor: size=0:8:8:8, shift=0:16:8:0
[ 0.416298] vesafb: framebuffer at 0xc0000000, mapped to 0xffffc90010100000, using 3072k, total 3072k
[ 0.477778] Console: switching to colour frame buffer device 128x48
[ 0.530645] fb0: VESA VGA frame buffer device
[ 0.530917] ACPI: acpi_idle registered with cpuidle
[ 0.557297] GHES: HEST is not enabled!
[ 0.557305] XENFS: not registering filesystem on non-xen platform
[ 0.557737] libphy: Fixed MDIO Bus: probed
[ 0.557999] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PSM1] at 0x60,0x64 irq 1,12
[ 0.561580] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.561601] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.562037] mousedev: PS/2 mouse device common for all mice
[ 0.562175] cpuidle: using governor ladder
[ 0.562284] cpuidle: using governor menu
[ 0.562288] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.562699] TCP: vegas registered
[ 0.562701] TCP: yeah registered
[ 0.562786] Key type dns_resolver registered
[ 0.563728] registered taskstats version 1
[ 0.564483] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 0.564936] powernow-k8: this CPU is not supported anymore, using acpi-cpufreq instead.
[ 0.566831] acpi-cpufreq: overriding BIOS provided _PSD data
[ 0.567786] Freeing unused kernel memory: 640k freed
[ 0.568164] CFS CPU scheduler.
[ 0.584465] systemd-udevd[507]: starting version 202
[ 0.653357] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.655531] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.655963] ehci-pci: EHCI PCI platform driver
[ 0.656097] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 0.656109] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 1
[ 0.656128] QUIRK: Enable AMD PLL fix
[ 0.656224] ohci_hcd 0000:00:12.0: irq 18, io mem 0xfeb4c000
[ 0.657747] SCSI subsystem initialized
[ 0.661333] ACPI: bus type scsi registered
[ 0.665103] libata version 3.00 loaded.
[ 0.711249] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.711257] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.711260] usb usb1: Product: OHCI Host Controller
[ 0.711263] usb usb1: Manufacturer: Linux 3.8.8-1-lqx ohci_hcd
[ 0.711266] usb usb1: SerialNumber: 0000:00:12.0
[ 0.711963] hub 1-0:1.0: USB hub found
[ 0.711978] hub 1-0:1.0: 5 ports detected
[ 0.712324] ehci-pci 0000:00:12.2: EHCI Host Controller
[ 0.712335] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 2
[ 0.712343] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 0.712361] ehci-pci 0000:00:12.2: debug port 1
[ 0.712428] ehci-pci 0000:00:12.2: irq 17, io mem 0xfeb4b000
[ 0.718188] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 0.718242] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.718249] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.718255] usb usb2: Product: EHCI Host Controller
[ 0.718260] usb usb2: Manufacturer: Linux 3.8.8-1-lqx ehci_hcd
[ 0.718264] usb usb2: SerialNumber: 0000:00:12.2
[ 0.718762] hub 2-0:1.0: USB hub found
[ 0.718770] hub 2-0:1.0: 5 ports detected
[ 0.719034] ehci-pci 0000:00:13.2: EHCI Host Controller
[ 0.719043] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3
[ 0.719061] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 0.719099] ehci-pci 0000:00:13.2: debug port 1
[ 0.719142] ehci-pci 0000:00:13.2: irq 17, io mem 0xfeb49000
[ 0.725166] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 0.725211] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.725218] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.725224] usb usb3: Product: EHCI Host Controller
[ 0.725230] usb usb3: Manufacturer: Linux 3.8.8-1-lqx ehci_hcd
[ 0.725235] usb usb3: SerialNumber: 0000:00:13.2
[ 0.725648] hub 3-0:1.0: USB hub found
[ 0.725656] hub 3-0:1.0: 5 ports detected
[ 0.725886] ahci 0000:00:11.0: version 3.0
[ 0.726156] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 0.726162] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 0.730354] scsi0 : ahci
[ 0.730816] scsi1 : ahci
[ 0.731197] scsi2 : ahci
[ 0.731481] scsi3 : ahci
[ 0.731816] scsi4 : ahci
[ 0.732139] scsi5 : ahci
[ 0.732460] ata1: SATA max UDMA/133 abar m1024@0xfeb4d000 port 0xfeb4d100 irq 19
[ 0.732464] ata2: SATA max UDMA/133 abar m1024@0xfeb4d000 port 0xfeb4d180 irq 19
[ 0.732468] ata3: SATA max UDMA/133 abar m1024@0xfeb4d000 port 0xfeb4d200 irq 19
[ 0.732471] ata4: SATA max UDMA/133 abar m1024@0xfeb4d000 port 0xfeb4d280 irq 19
[ 0.732475] ata5: SATA max UDMA/133 abar m1024@0xfeb4d000 port 0xfeb4d300 irq 19
[ 0.732478] ata6: SATA max UDMA/133 abar m1024@0xfeb4d000 port 0xfeb4d380 irq 19
[ 0.732661] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 0.732683] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 4
[ 0.732720] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfeb4a000
[ 0.787137] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.787142] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.787145] usb usb4: Product: OHCI Host Controller
[ 0.787148] usb usb4: Manufacturer: Linux 3.8.8-1-lqx ohci_hcd
[ 0.787151] usb usb4: SerialNumber: 0000:00:13.0
[ 0.787659] hub 4-0:1.0: USB hub found
[ 0.787670] hub 4-0:1.0: 5 ports detected
[ 0.787909] ohci_hcd 0000:00:14.5: OHCI Host Controller
[ 0.787918] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 5
[ 0.787944] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfeb48000
[ 0.842042] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.842046] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.842049] usb usb5: Product: OHCI Host Controller
[ 0.842052] usb usb5: Manufacturer: Linux 3.8.8-1-lqx ohci_hcd
[ 0.842054] usb usb5: SerialNumber: 0000:00:14.5
[ 0.842401] hub 5-0:1.0: USB hub found
[ 0.842410] hub 5-0:1.0: 2 ports detected
[ 1.036735] ata2: SATA link down (SStatus 0 SControl 300)
[ 1.036809] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.037712] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.037754] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.037797] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.121601] usb 2-5: new high-speed USB device number 3 using ehci-pci
[ 1.191503] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.197711] ata1.00: ATA-8: ST500LM012 HN-M500MBB, 2AR10002, max UDMA/133
[ 1.197719] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.203906] ata1.00: configured for UDMA/133
[ 1.204335] scsi 0:0:0:0: Direct-Access ATA ST500LM012 HN-M5 2AR1 PQ: 0 ANSI: 5
[ 1.212034] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 1.212041] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.212125] sd 0:0:0:0: [sda] Write Protect is off
[ 1.212130] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.212166] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.239240] usb 2-5: New USB device found, idVendor=12d1, idProduct=1506
[ 1.239251] usb 2-5: New USB device strings: Mfr=4, Product=3, SerialNumber=0
[ 1.239257] usb 2-5: Product: HUAWEI Mobile
[ 1.239263] usb 2-5: Manufacturer: Huawei Technologies
[ 1.239601] sda: sda1 sda2 sda3 sda4
[ 1.241058] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.248373] Initializing USB Mass Storage driver...
[ 1.248653] scsi6 : usb-storage 2-5:1.5
[ 1.249032] scsi7 : usb-storage 2-5:1.6
[ 1.250887] usbcore: registered new interface driver usb-storage
[ 1.250892] USB Mass Storage support registered.
[ 1.346272] usb 3-4: new high-speed USB device number 2 using ehci-pci
[ 1.402164] tsc: Refined TSC clocksource calibration: 1646.493 MHz
[ 1.402180] Switching to clocksource tsc
[ 1.463721] usb 3-4: New USB device found, idVendor=2232, idProduct=1020
[ 1.463730] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.463737] usb 3-4: Product: WebCam SC-0311139N
[ 1.463743] usb 3-4: Manufacturer: Image Processor
[ 1.463748] usb 3-4: SerialNumber: SM3711
[ 1.690741] usb 1-3: new full-speed USB device number 2 using ohci_hcd
[ 1.847612] usb 1-3: New USB device found, idVendor=0a5c, idProduct=219c
[ 1.847624] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.847631] usb 1-3: Product: Broadcom BCM2070 Bluetooth Device
[ 1.847637] usb 1-3: Manufacturer: Broadcom Corp
[ 1.847642] usb 1-3: SerialNumber: 30144A229E4B
[ 2.058659] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 2.250157] scsi 6:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2
[ 2.250876] scsi 7:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2
[ 2.302154] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 2.827197] systemd[1]: systemd 202 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 3.065305] systemd[1]: Inserted module 'autofs4'
[ 3.083044] systemd[1]: Set hostname to <REM>.
[ 3.104478] systemd[1]: /etc/mtab is not a symlink or not pointing to /proc/self/mounts. This is not supported anymore. Please make sure to replace this file by a symlink to avoid incorrect or misleading mount(8) output.
[ 3.673989] systemd[1]: logged here: 'Support for option SysVStartPriority= has been disabled at compile time and is ignored': 0
[ 3.928323] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 3.928445] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 3.928473] systemd[1]: Starting Remote File Systems.
[ 3.928499] systemd[1]: Reached target Remote File Systems.
[ 3.928520] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 3.928571] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 3.928589] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 3.928636] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 3.928654] systemd[1]: Starting Delayed Shutdown Socket.
[ 3.928708] systemd[1]: Listening on Delayed Shutdown Socket.
[ 3.928727] systemd[1]: Starting LVM2 metadata daemon socket.
[ 3.928777] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 3.928798] systemd[1]: Starting Encrypted Volumes.
[ 3.928818] systemd[1]: Reached target Encrypted Volumes.
[ 3.928949] systemd[1]: Starting udev Kernel Socket.
[ 3.928994] systemd[1]: Listening on udev Kernel Socket.
[ 3.929083] systemd[1]: Starting udev Control Socket.
[ 3.929127] systemd[1]: Listening on udev Control Socket.
[ 3.929179] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 3.929401] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 3.929433] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 3.929511] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 3.929537] systemd[1]: Starting Journal Socket.
[ 3.929627] systemd[1]: Listening on Journal Socket.
[ 3.929668] systemd[1]: Mounting Debug File System...
[ 3.941501] systemd[1]: Starting Setup Virtual Console...
[ 3.948777] systemd[1]: Starting udev Coldplug all Devices...
[ 4.302692] systemd[1]: Started Set Up Additional Binary Formats.
[ 4.302896] systemd[1]: Starting Create static device nodes in /dev...
[ 4.311080] systemd[1]: Mounting Huge Pages File System...
[ 4.333926] systemd[1]: Starting Apply Kernel Variables...
[ 4.344029] systemd[1]: Starting Journal Service...
[ 4.354053] systemd[1]: Started Journal Service.
[ 4.354159] systemd[1]: Mounting POSIX Message Queue File System...
[ 4.398484] systemd[1]: Starting Load Kernel Modules...
[ 4.405897] systemd[1]: Expecting device dev-sda2.device...
[ 4.405958] systemd[1]: Started File System Check on Root Device.
[ 4.405985] systemd[1]: Mounting Temporary Directory...
[ 4.444783] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 5.141813] EXT4-fs (sda3): re-mounted. Opts: data=ordered,commit=15
[ 5.523573] vboxdrv: Found 2 processor cores.
[ 5.523876] vboxdrv: fAsync=0 offMin=0x37b offMax=0x21cc
[ 5.524228] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 5.524230] vboxdrv: Successfully loaded version 4.2.12_OSE (interface 0x001a0004).
[ 5.585084] systemd-udevd[1417]: starting version 202
[ 6.551072] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 6.551149] ACPI: Lid Switch [LID]
[ 6.551279] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[ 6.551286] ACPI: Power Button [PWRB]
[ 6.551432] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[ 6.551436] ACPI: Sleep Button [SLPB]
[ 6.551556] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 6.551560] ACPI: Power Button [PWRF]
[ 6.557442] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 6.570168] ACPI: AC Adapter [ADP1] (on-line)
[ 6.576119] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
[ 6.581379] acpi device:31: registered as cooling_device2
[ 6.581414] ACPI: Video Device [VGA1] (multi-head: yes rom: no post: no)
[ 6.581535] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input5
[ 6.685232] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared
[ 6.685246] ACPI: Battery Slot [BAT1] (battery present)
[ 6.830273] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 6.830383] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 7.576782] [drm] Initialized drm 1.1.0 20060810
[ 7.618495] [drm] VGACON disable radeon kernel modesetting.
[ 7.620005] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 7.620007] [drm] No driver support for vblank timestamp query.
[ 7.620012] [drm] Initialized radeon 1.33.0 20080528 for 0000:00:01.0 on minor 0
[ 7.767784] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 7.767790] Disabling lock debugging due to kernel taint
[ 7.783921] <6>[fglrx] Maximum main memory to use for locked dma buffers: 3540 MBytes.
[ 7.784096] <6>[fglrx] vendor: 1002 device: 9806 count: 1
[ 7.784621] <6>[fglrx] ioport: bar 1, base 0xf000, size: 0x100
[ 7.785024] <6>[fglrx] Kernel PAT support is enabled
[ 7.785057] <6>[fglrx] module loaded - fglrx 9.1.11 [Dec 19 2012] with 1 minors
[ 8.571990] Adding 4194300k swap on /dev/sda2. Priority:-1 extents:1 across:4194300k
[ 10.299762] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 10.935682] psmouse serio1: elantech: assuming hardware version 3 (with firmware version 0x450f00)
[ 10.950057] psmouse serio1: elantech: Synaptics capabilities query result 0x08, 0x16, 0x0a.
[ 11.022649] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio1/input/input7
[ 11.032941] microcode: CPU0: patch_level=0x05000101
[ 14.667774] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0xb00, revision 0
[ 14.684494] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
[ 14.684678] sp5100_tco: PCI Revision ID: 0x42
[ 14.684818] sp5100_tco: Using 0xfed80b00 for watchdog MMIO address
[ 14.684869] sp5100_tco: Last reboot was not triggered by watchdog.
[ 14.685016] sp5100_tco: initialized (0xffffc9000003eb00). heartbeat=60 sec (nowayout=0)
[ 14.913699] systemd-logind[1501]: Watching system buttons on /dev/input/event1 (Lid Switch)
[ 14.914754] systemd-logind[1501]: Watching system buttons on /dev/input/event2 (Power Button)
[ 14.915967] systemd-logind[1501]: Watching system buttons on /dev/input/event3 (Sleep Button)
[ 14.916946] systemd-logind[1501]: Watching system buttons on /dev/input/event4 (Power Button)
[ 14.925385] systemd-logind[1501]: Watching system buttons on /dev/input/event5 (Video Bus)
[ 14.993314] microcode: failed to load file amd-ucode/microcode_amd.bin
[ 14.993343] microcode: CPU1: patch_level=0x05000101
[ 14.994827] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 15.200573] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 15.200964] r8169 0000:05:00.0: irq 40 for MSI/MSI-X
[ 15.204405] r8169 0000:05:00.0 eth0: RTL8168evl/8111evl at 0xffffc90000034000, 50:b7:c3:02:d7:05, XID 0c900800 IRQ 40
[ 15.204413] r8169 0000:05:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 15.290455] systemd-udevd[1420]: renamed network interface eth0 to enp5s0
[ 15.292678] systemd-sysctl[2033]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
[ 15.404438] samsung_laptop: detected SABI interface: SwSmi@
[ 15.404444] samsung_laptop: Backlight controlled by ACPI video driver
[ 15.452716] fglrx_pci 0000:00:01.0: irq 41 for MSI/MSI-X
[ 15.453760] <6>[fglrx] Firegl kernel thread PID: 2044
[ 15.453957] <6>[fglrx] Firegl kernel thread PID: 2045
[ 15.454361] <6>[fglrx] Firegl kernel thread PID: 2046
[ 15.454513] <6>[fglrx] IRQ 41 Enabled
[ 15.459141] <6>[fglrx] Gart USWC size:1156 M.
[ 15.459145] <6>[fglrx] Gart cacheable size:458 M.
[ 15.459152] <6>[fglrx] Reserved FB block: Shared offset:0, size:1000000
[ 15.459154] <6>[fglrx] Reserved FB block: Unshared offset:fc54000, size:3a0000
[ 15.459157] <6>[fglrx] Reserved FB block: Unshared offset:fff4000, size:c000
[ 15.461998] systemd-sysctl[2047]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
[ 15.698292] <6>[fglrx] ATIF platform detected with notification ID: 0x81
[ 16.424442] kvm: Nested Virtualization enabled
[ 16.424448] kvm: Nested Paging enabled
[ 16.499708] cfg80211: Calling CRDA to update world regulatory domain
[ 16.716267] Bluetooth: Core ver 2.16
[ 16.718230] NET: Registered protocol family 31
[ 16.718232] Bluetooth: HCI device and connection manager initialized
[ 16.718245] Bluetooth: HCI socket layer initialized
[ 16.718249] Bluetooth: L2CAP socket layer initialized
[ 16.718259] Bluetooth: SCO socket layer initialized
[ 16.733212] media: Linux media interface: v0.10
[ 16.782160] lib80211: common routines for IEEE802.11 drivers
[ 16.782166] lib80211_crypt: registered algorithm 'NULL'
[ 16.784149] Linux video capture interface: v2.00
[ 16.815091] usbcore: registered new interface driver usbserial
[ 16.816124] usbcore: registered new interface driver usbserial_generic
[ 16.817094] usbserial: USB Serial support registered for generic
[ 16.906678] usbcore: registered new interface driver option
[ 16.909342] usbserial: USB Serial support registered for GSM modem (1-port)
[ 16.909431] option 2-5:1.0: GSM modem (1-port) converter detected
[ 16.912145] usb 2-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 16.912225] option 2-5:1.3: GSM modem (1-port) converter detected
[ 16.915130] usb 2-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 16.915190] option 2-5:1.4: GSM modem (1-port) converter detected
[ 16.921982] usb 2-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 16.986926] systemd-udevd[1427]: error opening ATTR{/sys/devices/pci0000:00/0000:00:12.2/usb2/2-5/2-5:1.5/host6/scsi_host/host6/link_power_management_policy} for writing: No such file or directory
[ 16.988089] uvcvideo: Found UVC 1.00 device WebCam SC-0311139N (2232:1020)
[ 16.993277] systemd-udevd[1428]: error opening ATTR{/sys/devices/pci0000:00/0000:00:12.2/usb2/2-5/2-5:1.6/host7/scsi_host/host7/link_power_management_policy} for writing: No such file or directory
[ 17.002663] input: WebCam SC-0311139N as /devices/pci0000:00/0000:00:13.2/usb3/3-4/3-4:1.0/input/input8
[ 17.011802] usbcore: registered new interface driver uvcvideo
[ 17.011808] USB Video Class driver (1.1.1)
[ 17.036157] snd_hda_intel 0000:00:01.1: irq 42 for MSI/MSI-X
[ 17.055032] usbcore: registered new interface driver cdc_wdm
[ 17.076782] qmi_wwan 2-5:1.1: cdc-wdm0: USB WDM device
[ 17.085492] qmi_wwan 2-5:1.1 wwan0: register 'qmi_wwan' at usb-0000:00:12.2-5, WWAN/QMI device, 02:50:f3:00:00:00
[ 17.088340] usbcore: registered new interface driver qmi_wwan
[ 17.173910] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
[ 17.402599] INFO @wl_cfg80211_attach : Registered CFG80211 phy
[ 17.546699] input: HDA ATI SB Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[ 17.549997] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[ 17.554480] lib80211_crypt: registered algorithm 'TKIP'
[ 17.557087] eth0: Broadcom BCM4727 802.11 Hybrid Wireless Controller 5.100.82.112
[ 17.587070] sr0: scsi-1 drive
[ 17.587077] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 17.590908] sr 6:0:0:0: Attached scsi CD-ROM sr0
[ 17.764781] systemd-udevd[1426]: renamed network interface wwan0 to wwp0s18f2u5i1
[ 17.767245] systemd-sysctl[2747]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
[ 17.772802] systemd-udevd[1427]: renamed network interface eth0 to wlp3s0
[ 17.776265] systemd-sysctl[2756]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
[ 17.780048] systemd-sysctl[2755]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
[ 17.786438] systemd-sysctl[2759]: Duplicate assignment of kernel/sysrq in file '/usr/lib/sysctl.d/50-default.conf', ignoring.
[ 18.086526] usbcore: registered new interface driver btusb
[ 18.769655] ACPI Error: Needed [Integer/String/Buffer], found [Reference] ffff880136590af8 (20121018/exresop-422)
[ 18.769669] ACPI Exception: AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable] (20121018/dswexec-460)
[ 18.769676] ACPI Error: Method parse/execution failed [\_SB_.PCI0.VGA_.AF03] (Node ffff88013b4343e8), AE_AML_OPERAND_TYPE (20121018/psparse-537)
[ 18.769691] ACPI Error: Method parse/execution failed [\_SB_.PCI0.VGA_.ATIF] (Node ffff88013b434168), AE_AML_OPERAND_TYPE (20121018/psparse-537)
[ 20.495319] vboxpci: IOMMU not found (not registered)
[ 22.447778] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.447784] Bluetooth: BNEP filters: protocol multicast
[ 22.447799] Bluetooth: BNEP socket layer initialized
[ 22.595480] Bluetooth: RFCOMM TTY layer initialized
[ 22.595500] Bluetooth: RFCOMM socket layer initialized
[ 22.595502] Bluetooth: RFCOMM ver 1.11
[ 24.407804] r8169 0000:05:00.0 enp5s0: link down
[ 24.815261] NET: Registered protocol family 10
[ 24.815665] IPv6: ADDRCONF(NETDEV_UP): enp5s0: link is not ready
[ 31.811205] EXT4-fs (sda3): re-mounted. Opts: data=ordered,commit=15,commit=0
[ 32.023742] WARNING! power/level is deprecated; use power/control instead
[ 162.594332] fuse init (API version 7.20)
[ 181.712247] xfce4-session[4386]: segfault at ffffffff00000000 ip 00007fe7c8be9537 sp 00007fffd9c3f2e0 error 5 in libglib-2.0.so.0.3600.1[7fe7c8b86000+fc000]
[ 183.784141] <6>[fglrx] ATIF platform detected with notification ID: 0x81
[ 184.997887] ACPI Error: Needed [Integer/String/Buffer], found [Reference] ffff88013aae2948 (20121018/exresop-422)
[ 184.997901] ACPI Exception: AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable] (20121018/dswexec-460)
[ 184.997908] ACPI Error: Method parse/execution failed [\_SB_.PCI0.VGA_.AF03] (Node ffff88013b4343e8), AE_AML_OPERAND_TYPE (20121018/psparse-537)
[ 184.997923] ACPI Error: Method parse/execution failed [\_SB_.PCI0.VGA_.ATIF] (Node ffff88013b434168), AE_AML_OPERAND_TYPE (20121018/psparse-537)
[ 405.815701] NET: Registered protocol family 17
[ 1429.517360] xfce4-session[5257]: segfault at ffffffff00000000 ip 00007f53c2ee6537 sp 00007fff6060c2d0 error 5 in libglib-2.0.so.0.3600.1[7f53c2e83000+fc000]
[ 1430.198201] EXT4-fs (sda3): re-mounted. Opts: data=ordered,commit=15,commit=600
[ 1431.620829] EXT4-fs (sda3): re-mounted. Opts: data=ordered,commit=600,commit=600
[ 1432.769216] <6>[fglrx] ATIF platform detected with notification ID: 0x81
[ 1434.176644] ACPI Error: Needed [Integer/String/Buffer], found [Reference] ffff880136590360 (20121018/exresop-422)
[ 1434.176667] ACPI Exception: AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable] (20121018/dswexec-460)
[ 1434.176680] ACPI Error: Method parse/execution failed [\_SB_.PCI0.VGA_.AF03] (Node ffff88013b4343e8), AE_AML_OPERAND_TYPE (20121018/psparse-537)
[ 1434.176709] ACPI Error: Method parse/execution failed [\_SB_.PCI0.VGA_.ATIF] (Node ffff88013b434168), AE_AML_OPERAND_TYPE (20121018/psparse-537)
[ 1477.326788] usb 1-3: USB disconnect, device number 2
Any help appreciated.
Last edited by NinjaBus (2013-04-28 09:12:19)hadrons123 wrote:does it happen if you use the default arch kernel?
Yes, it keeps happening even with the default kernel when I try to shut down/suspend the computer (Alt-F4 key combination). I've read on some russian forum that it's the problem in recently upgraded glib2 (as they think), however downgrade didn't help. I'll try to check whether xfce4-session is to blame.
EDIT: It's definitely not xfce4-session, I tried previous version. Also, while running downgrade I saw that there is a newer version of glib2 in ARM, which is much more unstable, so I'm using 2.36.1-1.
Last edited by NinjaBus (2013-04-28 15:49:59) -
Problem with Intel/ATI Hybrid Graphics
Hi, I Just got a new laptop with the intel(hd4400)/ati(hd8670m) hybrid graphics. I followed exactly this https://wiki.archlinux.org/index.php/Hy … ons_So_Far, trying to disable my discrete card, but I did not have vgaswitcheroo under /sys/kernel/debug. Then I did a reboot, it stopped booting after FSCK, no login for me. I did add radeon and i915 to MODULES in /etc/mkinitcpio.conf if that's what you are wondering. I had to chroot with Arch installer and add a basic 20-intel.conf file to be able to boot into my DE.
dmesg output below shows that I had radeon loaded, but still no vgaswitcheroo directory.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.11.6-1-ARCH (nobody@var-lib-archbuild-extra-x86_64-thomas) (gcc version 4.8.1 20130725 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Oct 18 23:22:36 CEST 2013
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-linux root=/dev/mapper/vg_tf-lv_root rw quiet radeon.dpm=1
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000006efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000006f000-0x000000000006ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000070000-0x0000000000087fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000088000-0x00000000000bffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x0000000094d5ffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000094d60000-0x0000000095d5ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000095d60000-0x000000009a36efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009a36f000-0x000000009aebefff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000009aebf000-0x000000009afbefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000009afbf000-0x000000009affefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000009afff000-0x000000009affffff] usable
[ 0.000000] BIOS-e820: [mem 0x000000009b000000-0x000000009f9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fe101000-0x00000000fe112fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000feb00000-0x00000000feb0ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000015f5fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.31 by INSYDE Corp.
[ 0.000000] efi: ACPI=0x9affe000 ACPI 2.0=0x9affe014 SMBIOS=0x9aebef98
[ 0.000000] efi: mem00: type=3, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB)
[ 0.000000] efi: mem01: type=7, attr=0xf, range=[0x0000000000001000-0x000000000006f000) (0MB)
[ 0.000000] efi: mem02: type=0, attr=0xf, range=[0x000000000006f000-0x0000000000070000) (0MB)
[ 0.000000] efi: mem03: type=7, attr=0xf, range=[0x0000000000070000-0x0000000000088000) (0MB)
[ 0.000000] efi: mem04: type=6, attr=0x800000000000000f, range=[0x0000000000088000-0x000000000009f000) (0MB)
[ 0.000000] efi: mem05: type=0, attr=0xf, range=[0x000000000009f000-0x00000000000a0000) (0MB)
[ 0.000000] efi: mem06: type=2, attr=0xf, range=[0x0000000000100000-0x0000000001051000) (15MB)
[ 0.000000] efi: mem07: type=7, attr=0xf, range=[0x0000000001051000-0x0000000002000000) (15MB)
[ 0.000000] efi: mem08: type=2, attr=0xf, range=[0x0000000002000000-0x0000000002f51000) (15MB)
[ 0.000000] efi: mem09: type=7, attr=0xf, range=[0x0000000002f51000-0x000000003737a000) (836MB)
[ 0.000000] efi: mem10: type=2, attr=0xf, range=[0x000000003737a000-0x00000000379b5000) (6MB)
[ 0.000000] efi: mem11: type=7, attr=0xf, range=[0x00000000379b5000-0x000000006d8c0000) (863MB)
[ 0.000000] efi: mem12: type=2, attr=0xf, range=[0x000000006d8c0000-0x0000000092d70000) (596MB)
[ 0.000000] efi: mem13: type=4, attr=0xf, range=[0x0000000092d70000-0x0000000092d90000) (0MB)
[ 0.000000] efi: mem14: type=7, attr=0xf, range=[0x0000000092d90000-0x0000000093ee1000) (17MB)
[ 0.000000] efi: mem15: type=4, attr=0xf, range=[0x0000000093ee1000-0x0000000094d60000) (14MB)
[ 0.000000] efi: mem16: type=0, attr=0xf, range=[0x0000000094d60000-0x0000000095d60000) (16MB)
[ 0.000000] efi: mem17: type=7, attr=0xf, range=[0x0000000095d60000-0x0000000095f52000) (1MB)
[ 0.000000] efi: mem18: type=1, attr=0xf, range=[0x0000000095f52000-0x0000000095f6f000) (0MB)
[ 0.000000] efi: mem19: type=7, attr=0xf, range=[0x0000000095f6f000-0x0000000097260000) (18MB)
[ 0.000000] efi: mem20: type=4, attr=0xf, range=[0x0000000097260000-0x0000000097262000) (0MB)
[ 0.000000] efi: mem21: type=7, attr=0xf, range=[0x0000000097262000-0x0000000097272000) (0MB)
[ 0.000000] efi: mem22: type=2, attr=0xf, range=[0x0000000097272000-0x000000009727c000) (0MB)
[ 0.000000] efi: mem23: type=4, attr=0xf, range=[0x000000009727c000-0x0000000097c77000) (9MB)
[ 0.000000] efi: mem24: type=7, attr=0xf, range=[0x0000000097c77000-0x0000000097c7a000) (0MB)
[ 0.000000] efi: mem25: type=4, attr=0xf, range=[0x0000000097c7a000-0x0000000097c81000) (0MB)
[ 0.000000] efi: mem26: type=7, attr=0xf, range=[0x0000000097c81000-0x0000000097c82000) (0MB)
[ 0.000000] efi: mem27: type=4, attr=0xf, range=[0x0000000097c82000-0x0000000097db2000) (1MB)
[ 0.000000] efi: mem28: type=7, attr=0xf, range=[0x0000000097db2000-0x0000000097db3000) (0MB)
[ 0.000000] efi: mem29: type=4, attr=0xf, range=[0x0000000097db3000-0x0000000097e0a000) (0MB)
[ 0.000000] efi: mem30: type=3, attr=0xf, range=[0x0000000097e0a000-0x0000000097e17000) (0MB)
[ 0.000000] efi: mem31: type=4, attr=0xf, range=[0x0000000097e17000-0x0000000097e1f000) (0MB)
[ 0.000000] efi: mem32: type=3, attr=0xf, range=[0x0000000097e1f000-0x0000000097e20000) (0MB)
[ 0.000000] efi: mem33: type=4, attr=0xf, range=[0x0000000097e20000-0x0000000097e2c000) (0MB)
[ 0.000000] efi: mem34: type=3, attr=0xf, range=[0x0000000097e2c000-0x0000000097e34000) (0MB)
[ 0.000000] efi: mem35: type=4, attr=0xf, range=[0x0000000097e34000-0x0000000097e4c000) (0MB)
[ 0.000000] efi: mem36: type=7, attr=0xf, range=[0x0000000097e4c000-0x0000000097e4d000) (0MB)
[ 0.000000] efi: mem37: type=4, attr=0xf, range=[0x0000000097e4d000-0x0000000097e50000) (0MB)
[ 0.000000] efi: mem38: type=3, attr=0xf, range=[0x0000000097e50000-0x0000000097e57000) (0MB)
[ 0.000000] efi: mem39: type=4, attr=0xf, range=[0x0000000097e57000-0x0000000097e6e000) (0MB)
[ 0.000000] efi: mem40: type=3, attr=0xf, range=[0x0000000097e6e000-0x0000000097ee9000) (0MB)
[ 0.000000] efi: mem41: type=4, attr=0xf, range=[0x0000000097ee9000-0x0000000097efc000) (0MB)
[ 0.000000] efi: mem42: type=7, attr=0xf, range=[0x0000000097efc000-0x0000000097efd000) (0MB)
[ 0.000000] efi: mem43: type=4, attr=0xf, range=[0x0000000097efd000-0x0000000097f0b000) (0MB)
[ 0.000000] efi: mem44: type=7, attr=0xf, range=[0x0000000097f0b000-0x0000000097f0d000) (0MB)
[ 0.000000] efi: mem45: type=4, attr=0xf, range=[0x0000000097f0d000-0x000000009810f000) (2MB)
[ 0.000000] efi: mem46: type=3, attr=0xf, range=[0x000000009810f000-0x0000000098111000) (0MB)
[ 0.000000] efi: mem47: type=4, attr=0xf, range=[0x0000000098111000-0x0000000099f6f000) (30MB)
[ 0.000000] efi: mem48: type=3, attr=0xf, range=[0x0000000099f6f000-0x000000009a36f000) (4MB)
[ 0.000000] efi: mem49: type=5, attr=0x800000000000000f, range=[0x000000009a36f000-0x000000009a56f000) (2MB)
[ 0.000000] efi: mem50: type=6, attr=0x800000000000000f, range=[0x000000009a56f000-0x000000009aabf000) (5MB)
[ 0.000000] efi: mem51: type=0, attr=0xf, range=[0x000000009aabf000-0x000000009aebf000) (4MB)
[ 0.000000] efi: mem52: type=10, attr=0xf, range=[0x000000009aebf000-0x000000009afbf000) (1MB)
[ 0.000000] efi: mem53: type=9, attr=0xf, range=[0x000000009afbf000-0x000000009afff000) (0MB)
[ 0.000000] efi: mem54: type=4, attr=0xf, range=[0x000000009afff000-0x000000009b000000) (0MB)
[ 0.000000] efi: mem55: type=7, attr=0xf, range=[0x0000000100000000-0x000000015f600000) (1526MB)
[ 0.000000] efi: mem56: type=0, attr=0x0, range=[0x00000000000a0000-0x00000000000c0000) (0MB)
[ 0.000000] efi: mem57: type=0, attr=0x0, range=[0x000000009b000000-0x000000009fa00000) (74MB)
[ 0.000000] efi: mem58: type=11, attr=0x8000000000000001, range=[0x00000000e0000000-0x00000000f0000000) (256MB)
[ 0.000000] efi: mem59: type=0, attr=0x0, range=[0x00000000fe101000-0x00000000fe113000) (0MB)
[ 0.000000] efi: mem60: type=11, attr=0x8000000000000001, range=[0x00000000feb00000-0x00000000feb10000) (0MB)
[ 0.000000] efi: mem61: type=11, attr=0x8000000000000001, range=[0x00000000fec00000-0x00000000fec01000) (0MB)
[ 0.000000] efi: mem62: type=11, attr=0x8000000000000001, range=[0x00000000fed00000-0x00000000fed1c000) (0MB)
[ 0.000000] efi: mem63: type=11, attr=0x8000000000000000, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
[ 0.000000] efi: mem64: type=11, attr=0x8000000000000001, range=[0x00000000fed20000-0x00000000fee01000) (0MB)
[ 0.000000] efi: mem65: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x0000000100000000) (4MB)
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Dell Inc. Inspiron 3537/028XKX, BIOS A05 08/30/2013
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x15f600 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-E7FFF write-protect
[ 0.000000] E8000-EFFFF write-combining
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7F80000000 write-back
[ 0.000000] 1 base 0080000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 009B000000 mask 7FFF000000 uncachable
[ 0.000000] 3 base 009C000000 mask 7FFC000000 uncachable
[ 0.000000] 4 base 00FFC00000 mask 7FFFC00000 write-protect
[ 0.000000] 5 base 0100000000 mask 7F80000000 write-back
[ 0.000000] 6 base 015F600000 mask 7FFFE00000 uncachable
[ 0.000000] 7 base 015F800000 mask 7FFF800000 uncachable
[ 0.000000] 8 base 0160000000 mask 7FE0000000 uncachable
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0x9b000 max_arch_pfn = 0x400000000
[ 0.000000] Scanning 1 areas for low memory corruption
[ 0.000000] Base memory trampoline at [ffff88000007e000] 7e000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
[ 0.000000] [mem 0x00000000-0x000fffff] page 4k
[ 0.000000] BRK [0x02b2f000, 0x02b2ffff] PGTABLE
[ 0.000000] BRK [0x02b30000, 0x02b30fff] PGTABLE
[ 0.000000] BRK [0x02b31000, 0x02b31fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x15f400000-0x15f5fffff]
[ 0.000000] [mem 0x15f400000-0x15f5fffff] page 2M
[ 0.000000] BRK [0x02b32000, 0x02b32fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x15c000000-0x15f3fffff]
[ 0.000000] [mem 0x15c000000-0x15f3fffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x15bffffff]
[ 0.000000] [mem 0x100000000-0x13fffffff] page 1G
[ 0.000000] [mem 0x140000000-0x15bffffff] page 2M
[ 0.000000] init_memory_mapping: [mem 0x00100000-0x94d5ffff]
[ 0.000000] [mem 0x00100000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x3fffffff] page 2M
[ 0.000000] [mem 0x40000000-0x7fffffff] page 1G
[ 0.000000] [mem 0x80000000-0x94bfffff] page 2M
[ 0.000000] [mem 0x94c00000-0x94d5ffff] page 4k
[ 0.000000] init_memory_mapping: [mem 0x95d60000-0x9a36efff]
[ 0.000000] [mem 0x95d60000-0x95dfffff] page 4k
[ 0.000000] [mem 0x95e00000-0x9a1fffff] page 2M
[ 0.000000] [mem 0x9a200000-0x9a36efff] page 4k
[ 0.000000] BRK [0x02b33000, 0x02b33fff] PGTABLE
[ 0.000000] BRK [0x02b34000, 0x02b34fff] PGTABLE
[ 0.000000] init_memory_mapping: [mem 0x9afff000-0x9affffff]
[ 0.000000] [mem 0x9afff000-0x9affffff] page 4k
[ 0.000000] RAMDISK: [mem 0x3737a000-0x379b4fff]
[ 0.000000] ACPI: RSDP 000000009affe014 00024 (v02 DELL )
[ 0.000000] ACPI: XSDT 000000009affe210 000AC (v01 DELL CL09 00000001 01000013)
[ 0.000000] ACPI: FACP 000000009aff8000 0010C (v05 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI Error: Gpe0Block - 32-bit FADT register is too long (32 bytes, 256 bits) to convert to GAS struct - 255 bits max, truncating (20130517/tbfadt-202)
[ 0.000000] ACPI: DSDT 000000009afe9000 0B8AC (v01 DELL CL09 00000000 ASL 00040000)
[ 0.000000] ACPI: FACS 000000009afb8000 00040
[ 0.000000] ACPI: SLIC 000000009affd000 00176 (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: UEFI 000000009affc000 00236 (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: FPDT 000000009affa000 00044 (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: ASF! 000000009aff9000 000A5 (v32 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: HPET 000000009aff7000 00038 (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: APIC 000000009aff6000 0008C (v03 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: MCFG 000000009aff5000 0003C (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: SSDT 000000009afe8000 006FE (v01 COMPAL CRV ORB 00001000 ACPI 00040000)
[ 0.000000] ACPI: BOOT 000000009afe6000 00028 (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: ASPT 000000009afe4000 00034 (v07 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: DBGP 000000009afe3000 00034 (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: SSDT 000000009afdd000 00539 (v01 COMPAL CRV ORB 00003000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 000000009afdc000 00AD8 (v01 COMPAL CRV ORB 00003000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 000000009afd8000 0343C (v01 COMPAL CRV ORB 00003000 ACPI 00040000)
[ 0.000000] ACPI: SSDT 000000009afd5000 01E3D (v01 COMPAL CRV ORB 00001000 ACPI 00040000)
[ 0.000000] ACPI: BGRT 000000009afd7000 00038 (v01 DELL CL09 00000001 ASL 00040000)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000015f5fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x15f5fffff]
[ 0.000000] NODE_DATA [mem 0x15f5f8000-0x15f5fcfff]
[ 0.000000] [ffffea0000000000-ffffea00057fffff] PMD -> [ffff88015ac00000-ffff88015ebfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00001000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x15f5fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00001000-0x0006efff]
[ 0.000000] node 0: [mem 0x00070000-0x00087fff]
[ 0.000000] node 0: [mem 0x00100000-0x94d5ffff]
[ 0.000000] node 0: [mem 0x95d60000-0x9a36efff]
[ 0.000000] node 0: [mem 0x9afff000-0x9affffff]
[ 0.000000] node 0: [mem 0x100000000-0x15f5fffff]
[ 0.000000] On node 0 totalpages: 1018102
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 22 pages reserved
[ 0.000000] DMA zone: 3974 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 9742 pages used for memmap
[ 0.000000] DMA32 zone: 623472 pages, LIFO batch:31
[ 0.000000] Normal zone: 6104 pages used for memmap
[ 0.000000] Normal zone: 390656 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 56
[ 0.000000] PM: Registered nosave memory: [mem 0x0006f000-0x0006ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x00088000-0x000bffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000c0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x94d60000-0x95d5ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9a36f000-0x9aebefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9aebf000-0x9afbefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9afbf000-0x9affefff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9b000000-0x9f9fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x9fa00000-0xdfffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfe100fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe101000-0xfe112fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfe113000-0xfeafffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb00000-0xfeb0ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfeb10000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xffbfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xffc00000-0xffffffff]
[ 0.000000] e820: [mem 0x9fa00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88015f200000 s86528 r8192 d24064 u262144
[ 0.000000] pcpu-alloc: s86528 r8192 d24064 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1002170
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=/dev/mapper/vg_tf-lv_root rw quiet radeon.dpm=1
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 3856592K/4072408K available (5050K kernel code, 799K rwdata, 1696K rodata, 1140K init, 1288K bss, 215816K reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=8.
[ 0.000000] NR_IRQS:8448 nr_irqs:1016 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 16777216 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.003333] tsc: Detected 2294.570 MHz processor
[ 0.000003] Calibrating delay loop (skipped), value calculated using timer frequency.. 4590.35 BogoMIPS (lpj=7648566)
[ 0.000007] pid_max: default: 32768 minimum: 301
[ 0.000040] init_memory_mapping: [mem 0x9a36f000-0x9a56efff]
[ 0.000042] [mem 0x9a36f000-0x9a56efff] page 4k
[ 0.000064] init_memory_mapping: [mem 0x9a56f000-0x9aabefff]
[ 0.000066] [mem 0x9a56f000-0x9a5fffff] page 4k
[ 0.000067] [mem 0x9a600000-0x9a9fffff] page 2M
[ 0.000069] [mem 0x9aa00000-0x9aabefff] page 4k
[ 0.059748] Security Framework initialized
[ 0.059759] AppArmor: AppArmor disabled by boot time parameter
[ 0.059761] Yama: becoming mindful.
[ 0.060120] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.061320] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.061810] Mount-cache hash table entries: 256
[ 0.062052] Initializing cgroup subsys memory
[ 0.062063] Initializing cgroup subsys devices
[ 0.062065] Initializing cgroup subsys freezer
[ 0.062067] Initializing cgroup subsys net_cls
[ 0.062069] Initializing cgroup subsys blkio
[ 0.062098] CPU: Physical Processor ID: 0
[ 0.062100] CPU: Processor Core ID: 0
[ 0.062105] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.063398] mce: CPU supports 7 MCE banks
[ 0.063415] CPU0: Thermal monitoring enabled (TM1)
[ 0.063429] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0
tlb_flushall_shift: 6
[ 0.063562] Freeing SMP alternatives memory: 20K (ffffffff819e6000 - ffffffff819eb000)
[ 0.064699] ACPI: Core revision 20130517
[ 0.077923] ACPI: All ACPI Tables successfully acquired
[ 0.083767] ftrace: allocating 20100 entries in 79 pages
[ 0.096243] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.129231] smpboot: CPU0: Intel(R) Core(TM) i5-4200U CPU @ 1.60GHz (fam: 06, model: 45, stepping: 01)
[ 0.129240] TSC deadline timer enabled
[ 0.129252] Performance Events: PEBS fmt2+, 16-deep LBR, Haswell events, full-width counters, Intel PMU driver.
[ 0.129261] ... version: 3
[ 0.129262] ... bit width: 48
[ 0.129263] ... generic registers: 4
[ 0.129265] ... value mask: 0000ffffffffffff
[ 0.129267] ... max period: 0000ffffffffffff
[ 0.129268] ... fixed-purpose events: 3
[ 0.129269] ... event mask: 000000070000000f
[ 0.167457] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.152681] smpboot: Booting Node 0, Processors #1 #2 #3
[ 0.209878] Brought up 4 CPUs
[ 0.209882] smpboot: Total of 4 processors activated (18363.41 BogoMIPS)
[ 0.215147] devtmpfs: initialized
[ 0.216459] PM: Registering ACPI NVS region [mem 0x9aebf000-0x9afbefff] (1048576 bytes)
[ 0.217451] RTC time: 2:22:13, date: 11/08/13
[ 0.217501] NET: Registered protocol family 16
[ 0.217661] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.217663] ACPI: bus type PCI registered
[ 0.217666] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.217737] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.217740] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.252752] PCI: Using configuration type 1 for base access
[ 0.252922] dmi type 0xB1 record - unknown flag
[ 0.253726] bio: create slab <bio-0> at 0
[ 0.253868] ACPI: Added _OSI(Module Device)
[ 0.253870] ACPI: Added _OSI(Processor Device)
[ 0.253872] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.253874] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.256659] ACPI: EC: Look up EC in DSDT
[ 0.259524] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.272874] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.274013] ACPI: SSDT 000000009ae7dc18 003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20130117)
[ 0.274706] ACPI: Dynamic OEM Table Load:
[ 0.274709] ACPI: SSDT (null) 003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20130117)
[ 0.282313] ACPI: SSDT 000000009ae7d618 005AA (v01 PmRef ApIst 00003000 INTL 20130117)
[ 0.283108] ACPI: Dynamic OEM Table Load:
[ 0.283111] ACPI: SSDT (null) 005AA (v01 PmRef ApIst 00003000 INTL 20130117)
[ 0.301675] ACPI: SSDT 000000009ae7cd98 00119 (v01 PmRef ApCst 00003000 INTL 20130117)
[ 0.302368] ACPI: Dynamic OEM Table Load:
[ 0.302370] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20130117)
[ 0.431586] ACPI: Interpreter enabled
[ 0.431597] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20130517/hwxface-571)
[ 0.431606] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130517/hwxface-571)
[ 0.431630] ACPI: (supports S0 S3 S4 S5)
[ 0.431632] ACPI: Using IOAPIC for interrupt routing
[ 0.431666] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.431855] ACPI: No dock devices found.
[ 0.634551] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe])
[ 0.634846] acpi PNP0A08:00: Requesting ACPI _OSC control (0x1d)
[ 0.635302] acpi PNP0A08:00: ACPI _OSC control (0x1d) granted
[ 0.635816] PCI host bridge to bus 0000:00
[ 0.635820] pci_bus 0000:00: root bus resource [bus 00-fe]
[ 0.635823] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.635825] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.635828] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.635830] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
[ 0.635832] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
[ 0.635834] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
[ 0.635836] pci_bus 0000:00: root bus resource [mem 0x000cc000-0x000cffff]
[ 0.635838] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff]
[ 0.635840] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
[ 0.635842] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
[ 0.635844] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
[ 0.635846] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
[ 0.635848] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
[ 0.635850] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
[ 0.635852] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
[ 0.635854] pci_bus 0000:00: root bus resource [mem 0x000f0000-0x000fffff]
[ 0.635856] pci_bus 0000:00: root bus resource [mem 0x9fa00000-0xfeafffff]
[ 0.635867] pci 0000:00:00.0: [8086:0a04] type 00 class 0x060000
[ 0.636037] pci 0000:00:02.0: [8086:0a16] type 00 class 0x030000
[ 0.636053] pci 0000:00:02.0: reg 0x10: [mem 0xc0000000-0xc03fffff 64bit]
[ 0.636062] pci 0000:00:02.0: reg 0x18: [mem 0xb0000000-0xbfffffff 64bit pref]
[ 0.636069] pci 0000:00:02.0: reg 0x20: [io 0x5000-0x503f]
[ 0.636232] pci 0000:00:03.0: [8086:0a0c] type 00 class 0x040300
[ 0.636243] pci 0000:00:03.0: reg 0x10: [mem 0xc0810000-0xc0813fff 64bit]
[ 0.636435] pci 0000:00:14.0: [8086:9c31] type 00 class 0x0c0330
[ 0.636456] pci 0000:00:14.0: reg 0x10: [mem 0xc0800000-0xc080ffff 64bit]
[ 0.636523] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.636647] pci 0000:00:14.0: System wakeup disabled by ACPI
[ 0.636693] pci 0000:00:16.0: [8086:9c3a] type 00 class 0x078000
[ 0.636717] pci 0000:00:16.0: reg 0x10: [mem 0xc0818000-0xc081801f 64bit]
[ 0.636795] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.636949] pci 0000:00:1b.0: [8086:9c20] type 00 class 0x040300
[ 0.636965] pci 0000:00:1b.0: reg 0x10: [mem 0xc0814000-0xc0817fff 64bit]
[ 0.637037] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.637182] pci 0000:00:1c.0: [8086:9c14] type 01 class 0x060400
[ 0.637255] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.637400] pci 0000:00:1c.0: System wakeup disabled by ACPI
[ 0.637446] pci 0000:00:1c.3: [8086:9c16] type 01 class 0x060400
[ 0.637518] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.637662] pci 0000:00:1c.4: [8086:9c18] type 01 class 0x060400
[ 0.637734] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.637885] pci 0000:00:1d.0: [8086:9c26] type 00 class 0x0c0320
[ 0.638879] pci 0000:00:1d.0: reg 0x10: [mem 0xc081c000-0xc081c3ff]
[ 0.644729] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.644857] pci 0000:00:1d.0: System wakeup disabled by ACPI
[ 0.644903] pci 0000:00:1f.0: [8086:9c43] type 00 class 0x060100
[ 0.645161] pci 0000:00:1f.2: [8086:9c03] type 00 class 0x010601
[ 0.645179] pci 0000:00:1f.2: reg 0x10: [io 0x5088-0x508f]
[ 0.645188] pci 0000:00:1f.2: reg 0x14: [io 0x5094-0x5097]
[ 0.645196] pci 0000:00:1f.2: reg 0x18: [io 0x5080-0x5087]
[ 0.645205] pci 0000:00:1f.2: reg 0x1c: [io 0x5090-0x5093]
[ 0.645213] pci 0000:00:1f.2: reg 0x20: [io 0x5060-0x507f]
[ 0.645222] pci 0000:00:1f.2: reg 0x24: [mem 0xc081b000-0xc081b7ff]
[ 0.645264] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.645401] pci 0000:00:1f.3: [8086:9c22] type 00 class 0x0c0500
[ 0.645417] pci 0000:00:1f.3: reg 0x10: [mem 0xc0819000-0xc08190ff 64bit]
[ 0.645440] pci 0000:00:1f.3: reg 0x20: [io 0x5040-0x505f]
[ 0.645679] pci 0000:01:00.0: [10ec:8136] type 00 class 0x020000
[ 0.645710] pci 0000:01:00.0: reg 0x10: [io 0x4000-0x40ff]
[ 0.645750] pci 0000:01:00.0: reg 0x18: [mem 0xc0700000-0xc0700fff 64bit]
[ 0.645779] pci 0000:01:00.0: reg 0x20: [mem 0xc0400000-0xc0403fff 64bit pref]
[ 0.645873] pci 0000:01:00.0: supports D1 D2
[ 0.645875] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.652308] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.652312] pci 0000:00:1c.0: bridge window [io 0x4000-0x4fff]
[ 0.652316] pci 0000:00:1c.0: bridge window [mem 0xc0700000-0xc07fffff]
[ 0.652322] pci 0000:00:1c.0: bridge window [mem 0xc0400000-0xc04fffff 64bit pref]
[ 0.652414] pci 0000:02:00.0: [168c:0036] type 00 class 0x028000
[ 0.652447] pci 0000:02:00.0: reg 0x10: [mem 0xc0600000-0xc067ffff 64bit]
[ 0.652527] pci 0000:02:00.0: reg 0x30: [mem 0xffff0000-0xffffffff pref]
[ 0.652608] pci 0000:02:00.0: supports D1 D2
[ 0.652610] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.658964] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 0.658970] pci 0000:00:1c.3: bridge window [mem 0xc0600000-0xc06fffff]
[ 0.659066] pci 0000:03:00.0: [1002:6660] type 00 class 0x038000
[ 0.659093] pci 0000:03:00.0: reg 0x10: [mem 0xa0000000-0xafffffff 64bit pref]
[ 0.659113] pci 0000:03:00.0: reg 0x18: [mem 0xc0500000-0xc053ffff 64bit]
[ 0.659127] pci 0000:03:00.0: reg 0x20: [io 0x3000-0x30ff]
[ 0.659154] pci 0000:03:00.0: reg 0x30: [mem 0xfffe0000-0xffffffff pref]
[ 0.659233] pci 0000:03:00.0: supports D1 D2
[ 0.659235] pci 0000:03:00.0: PME# supported from D1 D2 D3hot
[ 0.665628] pci 0000:00:1c.4: PCI bridge to [bus 03]
[ 0.665632] pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
[ 0.665636] pci 0000:00:1c.4: bridge window [mem 0xc0500000-0xc05fffff]
[ 0.665642] pci 0000:00:1c.4: bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[ 0.665658] acpi PNP0A08:00: Disabling ASPM (FADT indicates it is unsupported)
[ 0.726347] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.726411] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.726470] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.726529] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.726588] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.726646] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.726705] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.726765] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.727383] ACPI: Enabled 5 GPEs in block 00 to 7F
[ 0.727392] ACPI: \_SB_.PCI0: notify handler is installed
[ 0.727488] Found 1 acpi root devices
[ 0.727533] ACPI: EC: GPE = 0xa, I/O: command/status = 0x66, data = 0x62
[ 0.727642] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.727647] vgaarb: loaded
[ 0.727648] vgaarb: bridge control possible 0000:00:02.0
[ 0.727700] PCI: Using ACPI for IRQ routing
[ 0.734096] PCI: pci_cache_line_size set to 64 bytes
[ 0.734149] e820: reserve RAM buffer [mem 0x0006f000-0x0006ffff]
[ 0.734151] e820: reserve RAM buffer [mem 0x00088000-0x0008ffff]
[ 0.734152] e820: reserve RAM buffer [mem 0x94d60000-0x97ffffff]
[ 0.734154] e820: reserve RAM buffer [mem 0x9a36f000-0x9bffffff]
[ 0.734157] e820: reserve RAM buffer [mem 0x9b000000-0x9bffffff]
[ 0.734158] e820: reserve RAM buffer [mem 0x15f600000-0x15fffffff]
[ 0.734265] NetLabel: Initializing
[ 0.734267] NetLabel: domain hash size = 128
[ 0.734268] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.734282] NetLabel: unlabeled traffic allowed by default
[ 0.734302] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.734309] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.736336] Switched to clocksource hpet
[ 0.741791] pnp: PnP ACPI init
[ 0.741808] ACPI: bus type PNP registered
[ 0.741844] pnp 00:00: [dma 4]
[ 0.741872] pnp 00:00: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.741898] pnp 00:01: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.742037] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.742091] system 00:03: [io 0x0680-0x069f] has been reserved
[ 0.742094] system 00:03: [io 0xfd60-0xfd63] has been reserved
[ 0.742096] system 00:03: [io 0xffff] has been reserved
[ 0.742099] system 00:03: [io 0xffff] has been reserved
[ 0.742101] system 00:03: [io 0xffff] has been reserved
[ 0.742103] system 00:03: [io 0x1800-0x18fe] could not be reserved
[ 0.742106] system 00:03: [io 0x164e-0x164f] has been reserved
[ 0.742109] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.742169] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.742223] system 00:05: [io 0x1854-0x1857] has been reserved
[ 0.742227] system 00:05: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.742290] pnp 00:06: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.742323] pnp 00:07: Plug and Play ACPI device, IDs DLL05eb PNP0f13 (active)
[ 0.799825] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.799828] system 00:08: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.799831] system 00:08: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.799833] system 00:08: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.799836] system 00:08: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.799838] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.799840] system 00:08: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.799843] system 00:08: [mem 0xff000000-0xff000fff] has been reserved
[ 0.799845] system 00:08: [mem 0xff010000-0xffffffff] could not be reserved
[ 0.799848] system 00:08: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.799850] system 00:08: [mem 0x9fa22000-0x9fa22fff] has been reserved
[ 0.799853] system 00:08: [mem 0x9fa10000-0x9fa1ffff] has been reserved
[ 0.799856] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.800510] pnp: PnP ACPI: found 9 devices
[ 0.800512] ACPI: bus type PNP unregistered
[ 0.807188] pci 0000:02:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[ 0.807192] pci 0000:03:00.0: no compatible bridge window for [mem 0xfffe0000-0xffffffff pref]
[ 0.807227] pci 0000:00:1c.3: BAR 15: assigned [mem 0x9fb00000-0x9fbfffff pref]
[ 0.807230] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.807234] pci 0000:00:1c.0: bridge window [io 0x4000-0x4fff]
[ 0.807240] pci 0000:00:1c.0: bridge window [mem 0xc0700000-0xc07fffff]
[ 0.807244] pci 0000:00:1c.0: bridge window [mem 0xc0400000-0xc04fffff 64bit pref]
[ 0.807251] pci 0000:02:00.0: BAR 6: assigned [mem 0x9fb00000-0x9fb0ffff pref]
[ 0.807254] pci 0000:00:1c.3: PCI bridge to [bus 02]
[ 0.807259] pci 0000:00:1c.3: bridge window [mem 0xc0600000-0xc06fffff]
[ 0.807263] pci 0000:00:1c.3: bridge window [mem 0x9fb00000-0x9fbfffff pref]
[ 0.807270] pci 0000:03:00.0: BAR 6: assigned [mem 0xc0540000-0xc055ffff pref]
[ 0.807272] pci 0000:00:1c.4: PCI bridge to [bus 03]
[ 0.807275] pci 0000:00:1c.4: bridge window [io 0x3000-0x3fff]
[ 0.807280] pci 0000:00:1c.4: bridge window [mem 0xc0500000-0xc05fffff]
[ 0.807285] pci 0000:00:1c.4: bridge window [mem 0xa0000000-0xafffffff 64bit pref]
[ 0.807584] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.807586] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.807589] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.807591] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
[ 0.807593] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
[ 0.807595] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
[ 0.807597] pci_bus 0000:00: resource 10 [mem 0x000cc000-0x000cffff]
[ 0.807599] pci_bus 0000:00: resource 11 [mem 0x000d0000-0x000d3fff]
[ 0.807601] pci_bus 0000:00: resource 12 [mem 0x000d4000-0x000d7fff]
[ 0.807603] pci_bus 0000:00: resource 13 [mem 0x000d8000-0x000dbfff]
[ 0.807605] pci_bus 0000:00: resource 14 [mem 0x000dc000-0x000dffff]
[ 0.807607] pci_bus 0000:00: resource 15 [mem 0x000e0000-0x000e3fff]
[ 0.807609] pci_bus 0000:00: resource 16 [mem 0x000e4000-0x000e7fff]
[ 0.807611] pci_bus 0000:00: resource 17 [mem 0x000e8000-0x000ebfff]
[ 0.807613] pci_bus 0000:00: resource 18 [mem 0x000ec000-0x000effff]
[ 0.807615] pci_bus 0000:00: resource 19 [mem 0x000f0000-0x000fffff]
[ 0.807617] pci_bus 0000:00: resource 20 [mem 0x9fa00000-0xfeafffff]
[ 0.807619] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff]
[ 0.807622] pci_bus 0000:01: resource 1 [mem 0xc0700000-0xc07fffff]
[ 0.807624] pci_bus 0000:01: resource 2 [mem 0xc0400000-0xc04fffff 64bit pref]
[ 0.807626] pci_bus 0000:02: resource 1 [mem 0xc0600000-0xc06fffff]
[ 0.807628] pci_bus 0000:02: resource 2 [mem 0x9fb00000-0x9fbfffff pref]
[ 0.807630] pci_bus 0000:03: resource 0 [io 0x3000-0x3fff]
[ 0.807632] pci_bus 0000:03: resource 1 [mem 0xc0500000-0xc05fffff]
[ 0.807635] pci_bus 0000:03: resource 2 [mem 0xa0000000-0xafffffff 64bit pref]
[ 0.807677] NET: Registered protocol family 2
[ 0.807890] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.808027] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.808127] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.808150] TCP: reno registered
[ 0.808162] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.808181] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.808261] NET: Registered protocol family 1
[ 0.808274] pci 0000:00:02.0: Boot video device
[ 0.823082] PCI: CLS 64 bytes, default 64
[ 0.823122] Unpacking initramfs...
[ 0.982411] Freeing initrd memory: 6380K (ffff88003737a000 - ffff8800379b5000)
[ 0.982417] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.982420] software IO TLB [mem 0x8ed70000-0x92d70000] (64MB) mapped at [ffff88008ed70000-ffff880092d6ffff]
[ 0.982447] Simple Boot Flag at 0x44 set to 0x1
[ 0.982626] Scanning for low memory corruption every 60 seconds
[ 0.982970] audit: initializing netlink socket (disabled)
[ 0.982981] type=2000 audit(1383877333.966:1): initialized
[ 1.000018] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.001570] zbud: loaded
[ 1.001748] VFS: Disk quotas dquot_6.5.2
[ 1.001801] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.001998] msgmni has been set to 7672
[ 1.002265] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.002308] io scheduler noop registered
[ 1.002311] io scheduler deadline registered
[ 1.002344] io scheduler cfq registered (default)
[ 1.002441] pcieport 0000:00:1c.0: irq 56 for MSI/MSI-X
[ 1.002526] pcieport 0000:00:1c.3: irq 57 for MSI/MSI-X
[ 1.002598] pcieport 0000:00:1c.4: irq 58 for MSI/MSI-X
[ 1.002681] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 1.002684] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt
[ 1.002688] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 1.002706] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
[ 1.002708] pci 0000:02:00.0: Signaling PME through PCIe PME interrupt
[ 1.002712] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
[ 1.002728] pcieport 0000:00:1c.4: Signaling PME through PCIe PME interrupt
[ 1.002730] pci 0000:03:00.0: Signaling PME through PCIe PME interrupt
[ 1.002734] pcie_pme 0000:00:1c.4:pcie01: service driver pcie_pme loaded
[ 1.002751] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.002769] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.002888] efifb: probing for efifb
[ 1.003509] efifb: framebuffer at 0xb0000000, mapped to 0xffffc90020e00000, using 4160k, total 4160k
[ 1.003511] efifb: mode is 1366x768x32, linelength=5504, pages=1
[ 1.003513] efifb: scrolling: redraw
[ 1.003515] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 1.007477] Console: switching to colour frame buffer device 170x48
[ 1.011265] fb0: EFI VGA frame buffer device
[ 1.011272] intel_idle: MWAIT substates: 0x11142120
[ 1.011274] intel_idle: v0.4 model 0x45
[ 1.011275] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.011336] GHES: HEST is not enabled!
[ 1.011398] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.011946] Linux agpgart interface v0.103
[ 1.012027] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.032274] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.032308] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.032411] mousedev: PS/2 mouse device common for all mice
[ 1.032672] rtc_cmos 00:04: RTC can wake from S4
[ 1.032819] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 1.032857] rtc_cmos 00:04: alarms up to one month, 242 bytes nvram, hpet irqs
[ 1.032871] Intel P-state driver initializing.
[ 1.032884] Intel pstate controlling: cpu 0
[ 1.032911] Intel pstate controlling: cpu 1
[ 1.032923] Intel pstate controlling: cpu 2
[ 1.032935] Intel pstate controlling: cpu 3
[ 1.033105] cpuidle: using governor ladder
[ 1.033295] cpuidle: using governor menu
[ 1.033356] drop_monitor: Initializing network drop monitor service
[ 1.033431] TCP: cubic registered
[ 1.033524] NET: Registered protocol family 10
[ 1.033688] NET: Registered protocol family 17
[ 1.033697] Key type dns_resolver registered
[ 1.033905] PM: Hibernation image not present or could not be loaded.
[ 1.033915] registered taskstats version 1
[ 1.034407] Magic number: 5:662:358
[ 1.034483] rtc_cmos 00:04: setting system clock to 2013-11-08 02:22:14 UTC (1383877334)
[ 1.035212] Freeing unused kernel memory: 1140K (ffffffff818c9000 - ffffffff819e6000)
[ 1.035213] Write protecting the kernel read-only data: 8192k
[ 1.037442] Freeing unused kernel memory: 1084K (ffff8800024f1000 - ffff880002600000)
[ 1.038163] Freeing unused kernel memory: 352K (ffff8800027a8000 - ffff880002800000)
[ 1.045866] systemd-udevd[57]: starting version 208
[ 1.050291] [drm] Initialized drm 1.1.0 20060810
[ 1.053926] [drm] radeon kernel modesetting enabled.
[ 1.053955] checking generic (b0000000 410000) vs hw (a0000000 10000000)
[ 1.053962] radeon 0000:03:00.0: enabling device (0000 -> 0003)
[ 1.054153] [drm] initializing kernel modesetting (HAINAN 0x1002:0x6660 0x1028:0x05EA).
[ 1.054190] [drm] register mmio base: 0xC0500000
[ 1.054191] [drm] register mmio size: 262144
[ 1.055856] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[ 1.982382] tsc: Refined TSC clocksource calibration: 2294.688 MHz
[ 2.566653] ATOM BIOS: Dell
[ 2.566668] [drm] GPU not posted. posting now...
[ 2.570040] radeon 0000:03:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 2.570042] radeon 0000:03:00.0: GTT: 512M 0x0000000040000000 - 0x000000005FFFFFFF
[ 2.570044] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 2.570045] [drm] RAM width 64bits DDR
[ 2.570094] [TTM] Zone kernel: Available graphics memory: 1965320 kiB
[ 2.570095] [TTM] Initializing pool allocator
[ 2.570099] [TTM] Initializing DMA pool allocator
[ 2.570117] [drm] radeon: 1024M of VRAM memory ready
[ 2.570118] [drm] radeon: 512M of GTT memory ready.
[ 2.570129] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 2.570456] [drm] probing gen 2 caps for device 8086:9c18 = 5323c42/0
[ 2.570460] [drm] PCIE gen 2 link speeds already enabled
[ 2.570620] [drm] Loading HAINAN Microcode
[ 2.981834] Switched to clocksource tsc
[ 2.993997] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[ 2.994098] radeon 0000:03:00.0: WB enabled
[ 2.994100] radeon 0000:03:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xffff880156e63c00
[ 2.994102] radeon 0000:03:00.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0xffff880156e63c04
[ 2.994103] radeon 0000:03:00.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0xffff880156e63c08
[ 2.994104] radeon 0000:03:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xffff880156e63c0c
[ 2.994106] radeon 0000:03:00.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0xffff880156e63c10
[ 2.994107] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 2.994108] [drm] Driver supports precise vblank timestamp query.
[ 2.994126] radeon 0000:03:00.0: irq 59 for MSI/MSI-X
[ 2.994137] radeon 0000:03:00.0: radeon: using MSI.
[ 2.994157] [drm] radeon: irq initialized.
[ 3.013688] [drm] ring test on 0 succeeded in 1 usecs
[ 3.013694] [drm] ring test on 1 succeeded in 1 usecs
[ 3.013698] [drm] ring test on 2 succeeded in 1 usecs
[ 3.013761] [drm] ring test on 3 succeeded in 2 usecs
[ 3.013770] [drm] ring test on 4 succeeded in 1 usecs
[ 3.015377] [drm] ib test on ring 0 succeeded in 0 usecs
[ 3.015424] [drm] ib test on ring 1 succeeded in 0 usecs
[ 3.015476] [drm] ib test on ring 2 succeeded in 0 usecs
[ 3.015496] [drm] ib test on ring 3 succeeded in 0 usecs
[ 3.015517] [drm] ib test on ring 4 succeeded in 1 usecs
[ 3.015656] [drm] Radeon Display Connectors
[ 3.015663] [drm] Internal thermal controller without fan control
[ 3.015712] [drm] probing gen 2 caps for device 8086:9c18 = 5323c42/0
[ 3.015739] == power state 0 ==
[ 3.015740] ui class: none
[ 3.015742] internal class: boot
[ 3.015744] caps:
[ 3.015746] uvd vclk: 0 dclk: 0
[ 3.015748] power level 0 sclk: 30000 mclk: 29900 vddc: 900 vddci: 0 pcie gen: 2
[ 3.015749] status: c r b
[ 3.015752] == power state 1 ==
[ 3.015753] ui class: performance
[ 3.015754] internal class: none
[ 3.015756] caps:
[ 3.015758] uvd vclk: 0 dclk: 0
[ 3.015760] power level 0 sclk: 30000 mclk: 30000 vddc: 800 vddci: 0 pcie gen: 2
[ 3.015761] power level 1 sclk: 40000 mclk: 90000 vddc: 875 vddci: 0 pcie gen: 2
[ 3.015763] power level 2 sclk: 75000 mclk: 90000 vddc: 950 vddci: 0 pcie gen: 2
[ 3.015765] power level 3 sclk: 90000 mclk: 90000 vddc: 1025 vddci: 0 pcie gen: 2
[ 3.015767] power level 4 sclk: 97500 mclk: 90000 vddc: 1075 vddci: 0 pcie gen: 2
[ 3.015768] status:
[ 3.015769] == power state 2 ==
[ 3.015771] ui class: battery
[ 3.015772] internal class: none
[ 3.015773] caps:
[ 3.015775] uvd vclk: 0 dclk: 0
[ 3.015777] power level 0 sclk: 30000 mclk: 30000 vddc: 800 vddci: 0 pcie gen: 2
[ 3.015778] power level 1 sclk: 40000 mclk: 60000 vddc: 850 vddci: 0 pcie gen: 2
[ 3.015780] power level 2 sclk: 40000 mclk: 60000 vddc: 850 vddci: 0 pcie gen: 2
[ 3.015781] status:
[ 3.023133] switching from power state:
[ 3.023135] ui class: none
[ 3.023136] internal class: boot
[ 3.023138] caps:
[ 3.023139] uvd vclk: 0 dclk: 0
[ 3.023141] power level 0 sclk: 30000 mclk: 29900 vddc: 900 vddci: 0 pcie gen: 2
[ 3.023142] status: c b
[ 3.023143] switching to power state:
[ 3.023144] ui class: performance
[ 3.023145] internal class: none
[ 3.023147] caps:
[ 3.023148] uvd vclk: 0 dclk: 0
[ 3.023149] power level 0 sclk: 30000 mclk: 30000 vddc: 800 vddci: 0 pcie gen: 2
[ 3.023151] power level 1 sclk: 40000 mclk: 90000 vddc: 875 vddci: 0 pcie gen: 2
[ 3.023152] power level 2 sclk: 75000 mclk: 90000 vddc: 950 vddci: 0 pcie gen: 2
[ 3.023154] power level 3 sclk: 90000 mclk: 90000 vddc: 1025 vddci: 0 pcie gen: 2
[ 3.023155] power level 4 sclk: 97500 mclk: 90000 vddc: 1075 vddci: 0 pcie gen: 2
[ 3.023156] status: r
[ 3.024470] [drm] radeon: dpm initialized
[ 3.024475] radeon 0000:03:00.0: No connectors reported connected with modes
[ 3.024477] [drm] Cannot find any crtc or sizes - going 1024x768
[ 3.026968] [drm] fb mappable at 0xA1150000
[ 3.026970] [drm] vram apper at 0xA0000000
[ 3.026971] [drm] size 3145728
[ 3.026972] [drm] fb depth is 24
[ 3.026973] [drm] pitch is 4096
[ 3.026976] checking generic (b0000000 410000) vs hw (a0000000 10000000)
[ 3.027040] radeon 0000:03:00.0: fb1: radeondrmfb frame buffer device
[ 3.027042] radeon 0000:03:00.0: registered panic notifier
[ 3.027053] [drm] Initialized radeon 2.34.0 20080528 for 0000:03:00.0 on minor 0
[ 3.027978] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0D:00/input/input1
[ 3.028026] ACPI: Lid Switch [LID0]
[ 3.028063] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/PNP0C0C:00/input/input2
[ 3.028066] ACPI: Power Button [PWRB]
[ 3.028114] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 3.028116] ACPI: Power Button [PWRF]
[ 3.031882] [drm] Memory usable by graphics device = 2048M
[ 3.031886] checking generic (b0000000 410000) vs hw (b0000000 10000000)
[ 3.031888] fb: conflicting fb hw usage inteldrmfb vs EFI VGA - removing generic driver
[ 3.031900] Console: switching to colour dummy device 80x25
[ 3.031959] i915 0000:00:02.0: setting latency timer to 64
[ 3.056716] i915 0000:00:02.0: irq 60 for MSI/MSI-X
[ 3.056723] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 3.056724] [drm] Driver supports precise vblank timestamp query.
[ 3.056784] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 3.101180] fbcon: inteldrmfb (fb0) is primary device
[ 4.361087] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 4.707482] Console: switching to colour frame buffer device 170x48
[ 4.712160] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 4.712553] [Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
[ 4.713578] ACPI Error: [\_SB_.PCI0.GFX0.DD02._BCL] Namespace lookup failure, AE_NOT_FOUND (20130517/psargs-359)
[ 4.713584] ACPI Error: Method parse/execution failed [\_SB_.PCI0.RP05.PEGP.DD02._BCL] (Node ffff880159325d98), AE_NOT_FOUND (20130517/psparse-536)
[ 4.713871] ACPI: Video Device [PEGP] (multi-head: yes rom: no post: no)
[ 4.713930] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:2f/LNXVIDEO:00/input/input4
[ 4.715381] acpi device:55: registered as cooling_device0
[ 4.715415] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.715455] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input5
[ 4.715487] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 1
[ 4.738967] ACPI: bus type USB registered
[ 4.738999] usbcore: registered new interface driver usbfs
[ 4.739016] usbcore: registered new interface driver hub
[ 4.739050] usbcore: registered new device driver usb
[ 4.739638] xhci_hcd 0000:00:14.0: setting latency timer to 64
[ 4.739642] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 4.739649] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[ 4.739721] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 4.739741] xhci_hcd 0000:00:14.0: irq 61 for MSI/MSI-X
[ 4.740145] xHCI xhci_add_endpoint called for root hub
[ 4.740148] xHCI xhci_check_bandwidth called for root hub
[ 4.740208] hub 1-0:1.0: USB hub found
[ 4.740218] hub 1-0:1.0: 9 ports detected
[ 4.741007] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.741164] ehci-pci: EHCI PCI platform driver
[ 4.742756] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 4.742760] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[ 4.743091] xHCI xhci_add_endpoint called for root hub
[ 4.743093] xHCI xhci_check_bandwidth called for root hub
[ 4.743135] hub 2-0:1.0: USB hub found
[ 4.743141] hub 2-0:1.0: 4 ports detected
[ 4.743425] SCSI subsystem initialized
[ 4.745035] ACPI: bus type ATA registered
[ 4.745122] libata version 3.00 loaded.
[ 4.747867] ehci-pci 0000:00:1d.0: setting latency timer to 64
[ 4.747875] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 4.747880] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 3
[ 4.747891] ehci-pci 0000:00:1d.0: debug port 2
[ 4.751784] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 4.751800] ehci-pci 0000:00:1d.0: irq 23, io mem 0xc081c000
[ 4.760774] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 4.760925] hub 3-0:1.0: USB hub found
[ 4.760930] hub 3-0:1.0: 2 ports detected
[ 4.761082] ahci 0000:00:1f.2: version 3.0
[ 4.761230] ahci 0000:00:1f.2: irq 62 for MSI/MSI-X
[ 4.774140] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x3 impl SATA mode
[ 4.774146] ahci 0000:00:1f.2: flags: 64bit ncq led clo only pio slum part deso sadm sds apst
[ 4.774151] ahci 0000:00:1f.2: setting latency timer to 64
[ 4.774614] scsi0 : ahci
[ 4.774722] scsi1 : ahci
[ 4.774798] scsi2 : ahci
[ 4.774868] ata1: SATA max UDMA/133 abar m2048@0xc081b000 port 0xc081b100 irq 62
[ 4.774871] ata2: SATA max UDMA/133 abar m2048@0xc081b000 port 0xc081b180 irq 62
[ 4.774873] ata3: DUMMY
[ 5.067345] usb 3-1: new high-speed USB device number 2 using ehci-pci
[ 5.094002] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.094032] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 5.099568] ata2.00: ATAPI: PLDS DVD+/-RW DU-8A5HH, SD12, max UDMA/100
[ 5.100914] ata2.00: configured for UDMA/100
[ 5.129572] ata1.00: ATA-8: ST500LT012-1DG142, 0001SDM1, max UDMA/133
[ 5.129577] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 5.191169] hub 3-1:1.0: USB hub found
[ 5.191237] hub 3-1:1.0: 8 ports detected
[ 5.255854] ata1.00: configured for UDMA/133
[ 5.256061] scsi 0:0:0:0: Direct-Access ATA ST500LT012-1DG14 0001 PQ: 0 ANSI: 5
[ 5.261341] scsi 1:0:0:0: CD-ROM PLDS DVD+-RW DU-8A5HH SD12 PQ: 0 ANSI: 5
[ 5.263686] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 5.263691] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 5.263724] sd 0:0:0:0: [sda] Write Protect is off
[ 5.263727] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.263737] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.269320] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.269323] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 5.269521] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 5.332482] sda: sda1 sda2
[ 5.333235] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.457253] usb 3-1.7: new high-speed USB device number 3 using ehci-pci
[ 5.549500] device-mapper: uevent: version 1.0.3
[ 5.549652] device-mapper: ioctl: 4.25.0-ioctl (2013-06-26) initialised: [email protected]
[ 5.554331] bio: create slab <bio-1> at 1
[ 5.607167] usb 3-1.8: new high-speed USB device number 4 using ehci-pci
[ 6.510287] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[ 7.581705] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
[ 7.582431] systemd[1]: Set hostname to <archins3537>.
[ 8.087615] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
[ 8.087670] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 8.087682] systemd[1]: Starting Login Prompts.
[ 8.087692] systemd[1]: Reached target Login Prompts.
[ 8.087700] systemd[1]: Starting Remote File Systems.
[ 8.087707] systemd[1]: Reached target Remote File Systems.
[ 8.087715] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
[ 8.087736] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ 8.087743] systemd[1]: Starting LVM2 metadata daemon socket.
[ 8.087762] systemd[1]: Listening on LVM2 metadata daemon socket.
[ 8.087769] systemd[1]: Starting Device-mapper event daemon FIFOs.
[ 8.087789] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[ 8.087796] systemd[1]: Starting Delayed Shutdown Socket.
[ 8.087813] systemd[1]: Listening on Delayed Shutdown Socket.
[ 8.087822] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
[ 8.087851] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 8.087858] systemd[1]: Starting Paths.
[ 8.087865] systemd[1]: Reached target Paths.
[ 8.087878] systemd[1]: Starting udev Kernel Socket.
[ 8.087895] systemd[1]: Listening on udev Kernel Socket.
[ 8.087904] systemd[1]: Starting udev Control Socket.
[ 8.087920] systemd[1]: Listening on udev Control Socket.
[ 8.087944] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
[ 8.088034] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 8.088043] systemd[1]: Starting Encrypted Volumes.
[ 8.088051] systemd[1]: Reached target Encrypted Volumes.
[ 8.088059] systemd[1]: Starting Journal Socket.
[ 8.088098] systemd[1]: Listening on Journal Socket.
[ 8.094096] systemd[1]: Started Set Up Additional Binary Formats.
[ 8.146808] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 8.147345] systemd[1]: Starting udev Coldplug all Devices...
[ 8.147641] systemd[1]: Starting Setup Virtual Console...
[ 8.156662] systemd[1]: Started Load Kernel Modules.
[ 8.156702] systemd[1]: Mounted FUSE Control File System.
[ 8.156719] systemd[1]: Mounting Debug File System...
[ 8.160118] systemd[1]: Starting Apply Kernel Variables...
[ 8.160456] systemd[1]: Mounting POSIX Message Queue File System...
[ 8.160770] systemd[1]: Mounting Configuration File System...
[ 8.161235] systemd[1]: Starting Journal Service...
[ 8.161549] systemd[1]: Started Journal Service.
[ 8.407759] systemd-journald[153]: Vacuuming done, freed 0 bytes
[ 8.622532] EXT4-fs (dm-1): re-mounted. Opts: data=ordered
[ 8.834003] systemd-udevd[177]: starting version 208
[ 9.449711] ACPI: Requesting acpi_cpufreq
[ 9.652388] snd_hda_intel 0000:00:03.0: irq 63 for MSI/MSI-X
[ 9.652512] snd_hda_intel 0000:00:1b.0: irq 64 for MSI/MSI-X
[ 9.703295] ACPI: AC Adapter [ACAD] (off-line)
[ 9.734702] wmi: Mapper loaded
[ 9.767167] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 9.900528] microcode: CPU0 sig=0x40651, pf=0x40, revision=0x15
[ 9.914682] ACPI: Battery Slot [BAT1] (battery present)
[ 9.946497] hda_codec: invalid CONNECT_LIST verb 5[1]:0
[ 9.946555] hda_codec: invalid CONNECT_LIST verb 6[1]:0
[ 9.946621] hda_codec: invalid CONNECT_LIST verb 7[1]:0
[ 9.948456] input: HDA Intel MID HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input7
[ 9.948585] input: HDA Intel MID HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input8
[ 9.948656] input: HDA Intel MID HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input9
[ 9.953096] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input10
[ 9.953371] ACPI Warning: 0x0000000000001828-0x000000000000182f SystemIO conflicts with Region \PMIO 1 (20130517/utaddress-251)
[ 9.953378] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 9.953384] ACPI Warning: 0x0000000000000830-0x000000000000083f SystemIO conflicts with Region \GPRL 1 (20130517/utaddress-251)
[ 9.953388] ACPI Warning: 0x0000000000000830-0x000000000000083f SystemIO conflicts with Region \GPR_ 2 (20130517/utaddress-251)
[ 9.953392] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 9.953394] ACPI Warning: 0x0000000000000800-0x000000000000082f SystemIO conflicts with Region \GPRL 1 (20130517/utaddress-251)
[ 9.953398] ACPI Warning: 0x0000000000000800-0x000000000000082f SystemIO conflicts with Region \GPR_ 2 (20130517/utaddress-251)
[ 9.953402] ACPI Warning: 0x0000000000000800-0x000000000000082f SystemIO conflicts with Region \IO_D 3 (20130517/utaddress-251)
[ 9.953406] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 9.953407] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 9.953792] mei_me 0000:00:16.0: setting latency timer to 64
[ 9.953838] mei_me 0000:00:16.0: irq 65 for MSI/MSI-X
[ 9.956390] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 9.956608] ACPI Warning: 0x0000000000005040-0x000000000000505f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130517/utaddress-251)
[ 9.956615] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 10.231648] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 10.250684] cfg80211: Calling CRDA to update world regulatory domain
[ 10.307646] input: Dell WMI hotkeys as /devices/virtual/input/input11
[ 10.310649] microcode: CPU1 sig=0x40651, pf=0x40, revision=0x15
[ 10.313166] microcode: CPU2 sig=0x40651, pf=0x40, revision=0x15
[ 10.313536] microcode: CPU3 sig=0x40651, pf=0x40, revision=0x15
[ 10.313923] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
[ 10.347294] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 10.347309] r8169 0000:01:00.0: can't disable ASPM; OS doesn't have ASPM control
[ 10.347544] r8169 0000:01:00.0: irq 66 for MSI/MSI-X
[ 10.347727] r8169 0000:01:00.0 eth0: RTL8106e at 0xffffc90022cee000, 74:86:7a:50:ce:f4, XID 04900000 IRQ 66
[ 10.381911] iTCO_vendor_support: vendor-support=0
[ 10.393283] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 10.393324] iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
[ 10.393578] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.400848] systemd-udevd[183]: renamed network interface eth0 to enp1s0
[ 10.416483] ath: EEPROM regdomain: 0x60
[ 10.416486] ath: EEPROM indicates we should expect a direct regpair map
[ 10.416489] ath: Country alpha2 being used: 00
[ 10.416490] ath: Regpair used: 0x60
[ 10.614808] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 10.615079] ieee80211 phy0: Atheros AR9565 Rev:1 mem=0xffffc90035180000, irq=19
[ 10.643067] rts5139: module is from the staging directory, the quality is unknown, you have been warned.
[ 10.643619] systemd-udevd[189]: renamed network interface wlan0 to wlp2s0
[ 10.646589] scsi3 : SCSI emulation for RTS5139 USB card reader
[ 10.646742]Cdh wrote:
You didn't give much information so...
Blacklisting is now done via /etc/modprobe.d/*.conf files
For example:
/etc/modprobe.d/disable-radeon.conf would contain
install radeon /bin/false
You can also write "blacklist radeon" instead but that only prevents loading it automatically on itself while booting. You can still modprobe it and if it is a dependency of an automatically loaded module it will still get loaded. With the install ... /bin/false there is no way to load it.
Also you need to make sure that it is not in the modules array in /etc/mkinitcpio.conf (or that your disable-radeon.conf is in the files array) because the initramfs is its own mini-system that doesn't know about the module configuration otherwise.
but thats the problem ! i need radeon module to start because vgaswitcheroo needs it ! and then trun it off because 'I' dont need it ! anyway i ll give 'bin/false' method a try !
Maybe you are looking for
-
How to convert BLOB into a String
Hi, I got a blob column from the database. It contains one XML File. How to convert it into String. I need the code for how to convert the blob into String Thanks in Advance.
-
I am wondering if there is a way to use some sort of code to put the total of what someone puts in there shopping cart at the top of my web page. here is the link to my site and you can see the shopping cart in the top left corner. Website. Thanks
-
HTML in Attribute used in message
Hello: I have created an attribute of type text in my flow. I what to paste some html txt into it and use it in a message(html body). I do this and it appears the mailer is encoding this data and replacing with no-html characters, i.e. "<" is changed
-
is it really best yet to get a new ipod ,because I lost my old one?
-
Printing from both a Mac and PC
I own Photoshop CS6 and am thinking of upgrading to CC. My large format printer is connected to a PC and my regular working station is a Mac connected to a 17" printer. Can I run both systems with one subscription to CC?