First DSLR for filming

Hey everyone,
I am looking for a DSLR for filming purposes. I have been recently watching reviews and video footages to see which is the best for me. Obviously a 5d mark II or III would be the best choice but unfrtunately I cannot afford it.
I have also checked the 60D which looks amazing because of the lcd screen which is adjustable but it has lower image quality, the 6D which also has a full frame sensor as the 5D. But the 60D is cheaper.
Which one do you suggest?
Solved!
Go to Solution.

I've used the 5D Mark II, 5D Mark III, and T3i for professional productions. I've not used the 60D or 7D. But, to start out, you can't go wrong with the T3i or T5i. The video is more than acceptable, and most viewers can't really tell the difference between the 5D Mark II and the T5i, not to mention the 60D. Now, the 5D Mark III is in another category altogether! The 5D Mark III is by far the best for DSLR video, but it's a little pricey for your first camera.
I would acquire the T5i (don't remember the non-US model number) and some good lenses. You can spend the difference between the T5i and 60D or 7D on some good non-S lenses that you can use as you upgrade bodies in the future. Spend your money on lenses first, then bodies. Your lenses will serve you much longer than your bodies!
Once you know that a DSLR meets your shooting requirements (they're still-frame cameras first, and video cameras second), you can either sell your T5i or use it as a backup/second camera when you buy a 5D Mark III or other Canon DSLR. Keep in mind that there are major limitations with all DSLRs when it comes to video, and make sure you can live with those limitations.
The major benefit for video of the T5i is the fold-out LCD screen. You will be shooting from different angles (high or low), and you can adjust the screen to compose your shot. Otherwise, you'll need an external monitor, rig, or other relatively expensive gear to adequately compose your shots.
A previous poster mentioned the Panasonic GH3, and that is a great camera for video, but the product line is not as broad or deep as Canon's. I think your decision to say with the Canon product line is good. Good luck in your shooting!

Similar Messages

Question for Film composer ( re bar )

Dears,
sometimes when you are working on a cue for film happen that your song start
(for ex.) at measure 250, because working on entire reel . My question is :
( I know other software are capable of..) Is possible to RE_BAR ?
In a few words is possible to transform ( example) measure Number 250 in measure Number 1 ?
Appreciate any suggestion. Thanks in advance
Antongiulio

ok if you have been given reels, you should have BITC (burnt in timecode - ie TC which shows up in your video) and you should make logics TC match. so if the first reel starts at 01:00:00:00 then you should make sure that as logic plays back the video its TC matchs.
if you try to cut time that would mean the smpte position of the first tempo (@ bar 1) would be a minus number, then logic will shift the tempo positions so that the first tempo is 0:00:00:00, meaning you will be out of sync with the video. if you started your project with 01:00:00:00 as your start of the first frame of the film, then you have a whole hour to play around with as your run up to the beginning of the film (of course you would never need as much as that but there you go).
i am assuming you are using digitized video and the movie as float. if you have used a capture device to digitize the video and the beginning of your QT movie is something like 00:59:52:12 for arguments sake, then you need to make your movie start line up with 01:00:00:00 at bar 1 in logic (which should also be set to have the first tempo at 01:00:00:00).
DO NOT use smpte offset, esp if you are not familiar with it. it will just create a lot of confusion. instead adjust the movie start on the QT movie you are using in logic to make the BITC match logics time code. once you have that set, you will never need to touch it again. you will be able to cut time, insert time and do whatever and the picture BITC and logics TC will always match.

Resolution for Still Photos for film

Greetings,
I have a full length Digital Video film and want to add still photos to it. I have been using Photo to Movie software to add a Ken Burns effect to the photo, then exporting it under the movie format- DV(NTSC) 720x480, then importing that to the final cut time line. My question is what is the best resolution in the first place for the still photo before I do this process or is it okay to use the final render size from the Photo to Movie export? Or do you have a better idea.

I would suggest you to check your export preferences but it is my understanding that if you render the movie file, and then export, it you should be able to set the QT option for NTSC DV.

Creating view to get first row for each table !!

I am having tables(more than 10) which are related using foreign key and primary key relationship.
Example:
Table1:
T1Prim T1Col1 T1Col2
Table2
T2For T2Prim T2Col1 T2Col2 T2Col3
(here T2For will have value same as T1Prim and in my design it has same column name i.e. T1Prim)
Table3
T3For T3Prim T3Col1 T3Col2 T3Col3
(here T3For will have value same as T2Prim)
and so on.
The data in the tables is like For table1 there will be one record, for table2 there will be one record and for table 3 there are more than one records.
Can i view either the first record for each of them or all records from each of them by writing the following view.
I have written a view like this:
Create or replace view test (T1Prim,T1Col1, T1Col2,T2Prim,T2Col1 T2Col2, T2Col3, T3Prim,T3Col1, T3Col2, T3Col3)
As
Select
Table1.T1Prim,
Table1.T1Col1,
Table1.T1Col2,
Table2.T2Prim,
Table2.T2Col1,
Table2.T2Col2,
Table2.T2Col3,
Table3.T3Prim,
Table3.T3Col1,
Table3.T3Col2,
Table3.T3Col3
From
Table1,
Table2,
Table3
where
Table1.Prim = Table2.For
and Table2.Prim = Table3.For
When i ran the select statement on the view I am not getting any data. Whereas there is data when select is ran on individual table.
Can someone please tell me where i am goofing.
Thanks in the anticipation that i will get some hint to solve this.
Eagerly waiting for reply.
Thanks !!

I mean use a collection :
Collection Methods
A collection method is a built-in function or procedure that operates on collections and is called using dot notation. The methods EXISTS, COUNT, LIMIT, FIRST, LAST, PRIOR, NEXT, EXTEND, TRIM, and DELETE help generalize code, make collections easier to use, and make your applications easier to maintain.
EXISTS, COUNT, LIMIT, FIRST, LAST, PRIOR, and NEXT are functions, which appear as part of an expression. EXTEND, TRIM, and DELETE are procedures, which appear as a statement. EXISTS, PRIOR, NEXT, TRIM, EXTEND, and DELETE take integer parameters. EXISTS, PRIOR, NEXT, and DELETE can also take VARCHAR2 parameters for associative arrays with string keys. EXTEND and TRIM cannot be used with index-by tables.
For more information, see "Using Collection Methods".
Syntax
Text description of the illustration collection_method_call.gif
Keyword and Parameter Description
collection_name
This identifies an index-by table, nested table, or varray previously declared within the current scope.
COUNT
COUNT returns the number of elements that a collection currently contains, which is useful because the current size of a collection is not always known. You can use COUNT wherever an integer expression is allowed.
For varrays, COUNT always equals LAST. For nested tables, normally, COUNT equals LAST. But, if you delete elements from the middle of a nested table, COUNT is smaller than LAST.
DELETE
This procedure has three forms. DELETE removes all elements from a collection. DELETE(n) removes the nth element from an index-by table or nested table. If n is null, DELETE(n) does nothing. DELETE(m,n) removes all elements in the range m..n from an index-by table or nested table. If m is larger than n or if m or n is null, DELETE(m,n) does nothing.
EXISTS
EXISTS(n) returns TRUE if the nth element in a collection exists. Otherwise, EXISTS(n) returns FALSE. Mainly, you use EXISTS with DELETE to maintain sparse nested tables. You can also use EXISTS to avoid raising an exception when you reference a nonexistent element. When passed an out-of-range subscript, EXISTS returns FALSE instead of raising SUBSCRIPT_OUTSIDE_LIMIT.
EXTEND
This procedure has three forms. EXTEND appends one null element to a collection. EXTEND(n) appends n null elements to a collection. EXTEND(n,i) appends n copies of the ith element to a collection. EXTEND operates on the internal size of a collection. So, if EXTEND encounters deleted elements, it includes them in its tally. You cannot use EXTEND with index-by tables.
FIRST, LAST
FIRST and LAST return the first and last (smallest and largest) subscript values in a collection. The subscript values are usually integers, but can also be strings for associative arrays. If the collection is empty, FIRST and LAST return NULL. If the collection contains only one element, FIRST and LAST return the same subscript value.
For varrays, FIRST always returns 1 and LAST always equals COUNT. For nested tables, normally, LAST equals COUNT. But, if you delete elements from the middle of a nested table, LAST is larger than COUNT.
index
This is an expression that must yield (or convert implicitly to) an integer in most cases, or a string for an associative array declared with string keys.
LIMIT
For nested tables, which have no maximum size, LIMIT returns NULL. For varrays, LIMIT returns the maximum number of elements that a varray can contain (which you must specify in its type definition).
NEXT, PRIOR
PRIOR(n) returns the subscript that precedes index n in a collection. NEXT(n) returns the subscript that succeeds index n. If n has no predecessor, PRIOR(n) returns NULL. Likewise, if n has no successor, NEXT(n) returns NULL.
TRIM
This procedure has two forms. TRIM removes one element from the end of a collection. TRIM(n) removes n elements from the end of a collection. If n is greater than COUNT, TRIM(n) raises SUBSCRIPT_BEYOND_COUNT. You cannot use TRIM with index-by tables.
TRIM operates on the internal size of a collection. So, if TRIM encounters deleted elements, it includes them in its tally.
Usage Notes
You cannot use collection methods in a SQL statement. If you try, you get a compilation error.
Only EXISTS can be applied to atomically null collections. If you apply another method to such collections, PL/SQL raises COLLECTION_IS_NULL.
You can use PRIOR or NEXT to traverse collections indexed by any series of subscripts. For example, you can use PRIOR or NEXT to traverse a nested table from which some elements have been deleted.
EXTEND operates on the internal size of a collection, which includes deleted elements. You cannot use EXTEND to initialize an atomically null collection. Also, if you impose the NOT NULL constraint on a TABLE or VARRAY type, you cannot apply the first two forms of EXTEND to collections of that type.
If an element to be deleted does not exist, DELETE simply skips it; no exception is raised. Varrays are dense, so you cannot delete their individual elements.
PL/SQL keeps placeholders for deleted elements. So, you can replace a deleted element simply by assigning it a new value. However, PL/SQL does not keep placeholders for trimmed elements.
The amount of memory allocated to a nested table can increase or decrease dynamically. As you delete elements, memory is freed page by page. If you delete the entire table, all the memory is freed.
In general, do not depend on the interaction between TRIM and DELETE. It is better to treat nested tables like fixed-size arrays and use only DELETE, or to treat them like stacks and use only TRIM and EXTEND.
Within a subprogram, a collection parameter assumes the properties of the argument bound to it. So, you can apply methods FIRST, LAST, COUNT, and so on to such parameters. For varray parameters, the value of LIMIT is always derived from the parameter type definition, regardless of the parameter mode.
Examples
In the following example, you use NEXT to traverse a nested table from which some elements have been deleted:
i := courses.FIRST; -- get subscript of first element
WHILE i IS NOT NULL LOOP
-- do something with courses(i)
i := courses.NEXT(i); -- get subscript of next element
END LOOP;
In the following example, PL/SQL executes the assignment statement only if element i exists:
IF courses.EXISTS(i) THEN
courses(i) := new_course;
END IF;
The next example shows that you can use FIRST and LAST to specify the lower and upper bounds of a loop range provided each element in that range exists:
FOR i IN courses.FIRST..courses.LAST LOOP ...
In the following example, you delete elements 2 through 5 from a nested table:
courses.DELETE(2, 5);
In the final example, you use LIMIT to determine if you can add 20 more elements to varray projects:
IF (projects.COUNT + 20) < projects.LIMIT THEN
-- add 20 more elements
Related Topics
Collections, Functions, Procedures
http://download-west.oracle.com/docs/cd/B10501_01/appdev.920/a96624/13_elems7.htm#33054
Joel P�rez

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

I have 2 itunes accounts. I can no longer use my first one for purchases so I had to start a new one and it will not sync from my new one without deleting everything on my same ipod from my previous account. How do I sync between both accounts?

I have 2 itunes accounts. I can no longer use my first one for purchases so I had to start a new one and it will not sync from my new one without deleting everything on my same ipod from my previous account. How do I sync between both accounts?

Wayland wrote:
The CS.com service account has long been closed. I cannot get it to respond to my years ago password for that account. So I ask them to send me a new password and of course it goes to my years ago email number.
Don't have it send email.
Answer the security questions.

How can I save the first dept. for an employee in a transport table?

Hi All,
I have created a table to store the transports to an employee from department to another department.
the first department number to every employee is stored at the parent table called employees.
when I insert a new record to the transports table (which is the child for the parent employees) for an employee and the manager agrees for this transport the original value of department number in employees table will be changed to the new one. I done this process through a db trigger on the transport table.
Now the problem is that the original value of the first department number will be lost cause of the db trigger that changes this value after manager agreement!
I looked to solve the problem by adding a new column in employees table to save the first dept. no. for each employee only if Count of records = 1 for that employee like this:
-- Before Update DB Trigger on Transports Table:
DECLARE
pragma autonomous_transaction;
N NUMBER;
BEGIN
SELECT count(EMP_SID) -- emp-sid is the FK referenced from employeess.emp_sid
INTO N
FROM TRANSPORT_TRANS
where emp_sid=:NEW.EMP_SID
GROUP BY EMP_SID;
     IF :NEW.AGREE_FLG = 1 AND N = 1 THEN -- If the manager agrees and this record is the first one for that employee
     UPDATE EMPLOYEESS E
     SET E.FST_AD=E.ADMINISTRATION_SID, -- E.ADMINISTRATION_SID has the oroginal value for admin no. and FST_AD is the new column to save the first value
            E.FST_HE=E.HEADQUARTERS_SID,
            E.ADMINISTRATION_SID = :OLD.ADMIN_SID, -- changing the value with then new one added on the table
            E.HEADQUARTERS_SID = :OLD.HEAD_SID
           WHERE E.EMP_SID = :OLD.EMP_SID;
     ELSIF :NEW.AGREE_FLG = 1 AND N != 1 THEN -- if the manager agrees but the record is not the first record for that employee
     UPDATE EMPLOYEESS E
        SET   E.ADMINISTRATION_SID = :OLD.ADMIN_SID, -- only change the original values
                 E.HEADQUARTERS_SID = :OLD.HEAD_SID
                 WHERE E.EMP_SID = :OLD.EMP_SID;
     END IF;
END;But the form gives me this error if I deleted (pragma autonomous_transaction;) st. :
ORA-04091: table transports is mutating, trigger/function may not see it
But when I keep it, the form gives me this error:
ORA-06519: active autonomous transaction detected and rolled back
Edited by: Dev. Musbah on Aug 18, 2009 2:09 AM

Dev. Musbah,
First make sure that the insert statement executes. And check whether other error messages are getting. Currently you are checking only NO_DATA_FOUND. so change the exception part with
EXCEPTION
     WHEN NO_DATA_FOUND THEN NULL;
     WHEN OTHERS THEN MESSAGE('Some Error Occured');Regards,
Manu.
If this answer is helpful or correct, please mark it. Thanks.

Getting the first row for each group

Hi Everyone,
I have a query which returns a number of rows, all of which are valid. What I need to do is to get the first row for each group and work with those records.
For example ...
client flight startairport destairport stops
A fl123 LGW BKK 2
A fl124 LHR BKK 5
B fl432 LGW XYZ 7
B fl432 MAN ABC 8
.... etc.
I would need to return one row for Client A and one row for Client B (etc.) but find that I can't use the MIN function because it would return the MIN value for each column (i.e. mix up the rows). I also can use the rownum=1 because this would only return one row rather than one row per group (i.e. per client).
I have been investigating and most postings seem to say that it needs a second query to look up the first row for each grouping. This is a solution which would not really be practical because my query is already quite complex and incorporating duplicate subqueries would just make the whole thing much to cumbersome.
So what I really new is a "MIN by group" or a "TOP by group" or a "ROWNUM=1 by group" function.
Can anyone help me with this? I'm sure that there must be a command to handle this.
Regards and any thanks,
Alan Searle
Cologne, Germany

Something like this:
select *
from (
   select table1.*
   row_number() over (partition by col1, col2 order by col3, col4) rn
   from table1
where rn = 1In the "partition by" clause you place what you normally would "group by".
In the "order by" clause you define which will have row_number = 1.
Edit:
PS. The [url http://download.oracle.com/docs/cd/E11882_01/server.112/e17118/functions004.htm#i81407]docs have more examples on using analytical functions ;-)
Edited by: Kim Berg Hansen on Sep 16, 2011 10:46 AM

First row for each entry

hi
i have sorted the internal table by field f1 and i need to insert the first row for each f1 entry.
I tried AT NEW f1. But that doesnt seem to work.
Kindlly help.
Thanks.

*--ENSURE THAT age IS FIRST FIELD IN INTERNAL TABLE it_gir while declaring it.....
SORT it_gir BY age ASCENDING.
LOOP AT it_gir INTO wa_gir.
AT NEW age.
*--if there are fields which are getting populated with **** instead of original values....then use below statement...
read table it_gir index sy-tabix.
MOVE-CORRESPONDING wa_gir TO wa_final1.
APPEND wa_final1 TO it_final1.
clear wa_final1.
ENDAT.
ENDLOOP.
now it should definitely work.....
if not check in debugging mode if data exists or not....!!!
Regards
Vasu

Is anyone else having email problems such as apps exiting in the middle of an email? It may be a wireless issue. I use First Class for work and yahoo email for personal. I will be in the middle of typing a long email and the app just quits, all data lost.

Is anyone else having email problems such as apps exiting in the middle of an email? It may be a wireless issue. I use First Class for work and yahoo email for personal. I will be in the middle of typing a long email and the app just quits, all data lost.

Have you tried restarting or resetting your iPad?
Restart: Press On/Off button until the Slide to Power Off slider appears, select Slide to Power Off and, after the iPad shuts down, then press the On/Off button until the Apple logo appears.
Reset: Press the Home and On/Off buttons at the same time and hold them until the Apple logo appears (about 10 seconds). Ignore the "Slide to power off"

Hi.at first sorry for my bad english language.i have mac book pro with two os(win7 and mac10.9.3)when i want to restore my iPad air in mac os iTunes error 17 but in win7 easily restore!why?

hi.at first sorry for my bad english language.i have mac book pro with two os(win7 and mac10.9.3)when i want to restore my iPad air in mac os iTunes error 17 but in win7 easily restore!why?

Hi there saharalirezaie,
You may find the troubleshooting steps in the article below helpful.
Resolve specific iTunes update and restore errors
http://support.apple.com/kb/ts3694
Resolve communication issues
Related errors: 17, 1004, 1013, 1638, 3014, 3194, 3000, 3002, 3004, 3013, 3014, 3015, 3194, or 3200. These alerts refer to gs.apple.com, say "There was a problem downloading the software," or say the "device isn't eligible for the requested build."
Check the hosts file or TCP/IP filtering, which might cause communication issues between iTunes, ports, and servers.
-Griff W.

I want to know why some box of Iphone5s it's not come full accessories in box simple my iPhone 5s I have bought from Apple store last week it's first time for me use iPhone but so surprise me how the company make the phone have to use a pin to open

I want to know why some box of Iphone5s it's not come full accessories in box simple my iPhone 5s I have bought from Apple store last week it's first time for me use iPhone but so surprise me how the company make the phone have to use a pin to open the sim but didn't give a pin inside the box and I ask staff at store their said they also don't know some box have some of are don't have a pin come together so then they told me I have to find solution or I have to buy a pin by my self I can buy it by myself but I really don't understand how come apple big company but how it's happen like this?thank you.

Where did you purchase this. The US phones do not come with the SIM removal tool anymore. They haven't for some time now. I'm not even sure it comes with any of the devices anymore. You can just straighten out a paper clip and do the same thing.

QM for Film Mfg. Industry

Dear All,
I want to know about Quality Management in Film Mfg. Industry / Paper Industry.
Please tell me, where i can get information for this.
I have a query in QM for Film Mfg. Industry.
The problem is:
Film production is in ROLLs. Base unit of measure is KG.
I want to segregate defective area inside the roll, while usage decision. area is in sq.meters
There is no extra field for this in standard transaction, as per my knowledge.
Please help.
my email id : [email protected]
GNK

I can't help you specifically with your question. But you might want to look at SAP's Mill products solutions. What you describe is very similar to what happens in the mills that produce things like carpet or rolled sheet metal. The carpet and metal are made in rolls measured in sq. ft. but very often managed and stored as EA. Defections are related to certain areas of the roll.
The following is from SAP's documentation on this solution, bolidng is mine.
Purpose
The SAP Mill Products component adds sector-specific functionality to an ERP system to satisfy the complex requirements of mill industries (e.g. metal, wood, paper, textiles, construction materials, and cable sectors).
These industry segments differ from others primarily in that the materials used have a large number of characteristics and variants. The materials in the segments listed above are also predominantly area-based (e.g. paper, textiles, plastic film) or length-based (e.g. cables, piping). Account must be taken of these material characteristics throughout the entire supply chain.
To cater for the particularities of these industry segments, SAP Mill Products features processes and functions that cover the entire supply-chain cycle from product design and configuration, through planning, order processing, capacity planning and production, to final delivery. Additional functions are available in costing and inventory management. SAP Mill Products are also integrated into Quality Management, Financial Accounting, and Controlling.
Here's the link:
http://help.sap.com/saphelp_dimp50/helpdata/EN/4e/1796374b088e5ce10000009b38f8cf/frameset.htm
Craig
Edited by: Craig Snyder on Mar 7, 2008 5:35 PM

Adobe Photoshop Elements 9 will not recognize Epson V600 Photo scanner for film ?

For some reason the WIA support in PE9 will only recognize the scanner for reflective prints not film, why ?
But, in the PE 6 the Epson V600 scanner is recognized for film scanning,, in professional mode and automatic.
Any clues ?
Message was edited by:Photographer & Dell Technical Service solved this issue to-day 11/02/2015
Message was edited by: Bob Dix

See this Tech doc:
http://helpx.adobe.com/photoshop-elements/kb/twain-installed-photoshop-elements-11.html

How to pull a max value/first value for duplicates in a group in a query?

Hi everybody,
[Oracle 10g]
I'm working with two tables, tblPatient and tblProgressNotes. The fields I'm working with are:
<pre>
<li>tblPatient.PatientID</li>
<li>tblPatient.EpisodeNumber (this tracks the number of hospital visits)</li>
<li>tblPatient.DischargeDate</li>
<li>tblProgressNotes.Height</li>
<li>tblProgressNotes.Weight</li>
<li>tblProgressNotes.Girth</li>
<li>tblProgressNotes.EntryDate</li>
<li>tblProgressNotes.EntryTime</li>
</pre>
From the fields above, I need to pull the most recent episode for each patient and each unique entry date so I can collect the height, weight, girth, and chart the plots on a graph. The problem I'm running into, though, is that there may be multiple entries on a given day. I can get the most recent episode for each patient with a "WHERE tblPatient.DischargeDate Is Null," but I'm not sure how to pull just the unique dates for each patient.
For instance, if I have the following:
<pre>
 PatientID EpisodeNumber EntryDate EntryTime Height Weight Girth
1 1 01.01.13 1:03 PM 66 185 35.5
1 1 01.01.13 7:18 PM 66 184 36
1 1 01.07.13 8:57 AM 66 190 36
1 1 01.07.13 11:32 AM 66 189 35.5
</pre>
For the first two records, I only want to return one record on 01.01.13. What I would really like, if there is more than one entry on a single day, is to take the average of the height, weight, and girth entries for that day and return a single record (I don't need the time entries, but I included them initially for testing). So, this is what my desired output would look like:
<pre>
 PatientID EpisodeNumber EntryDate Height Weight Girth
1 1 01.01.13 66 184.5 35.75
1 1 01.07.13 66 189.5 35.75
</pre>
If it's not possible to write a query like the above, then I would like to take the first entry for each day where there are multiple entries on that day. So, this would be the desired output (I included the EntryTime again so you can compare to the original example):
<pre>
 PatientID EpisodeNumber EntryDate EntryTime Height Weight Girth
1 1 01.01.13 1:03 PM 66 185 35.5
1 1 01.07.13 8:57 AM 66 190 36
</pre>
Thanks for your help.

Hi,
987019 wrote:
Here's some sample data:
CREATE TABLE TBLPATIENT
PATID VARCHAR2 (20),
EPISODE_NUMBER DOUBLE,
DATE_OF_DISCHARGE DATE
CREATE TABLE TBLPROGRESSNOTES
PATID VARCHAR2 (20),
EPISODE_NUMBER DOUBLE,
DATA_ENTRY_DATE DATE,
GIRTH VARCHAR2 (5),
HEIGHT DOUBLE,
WEIGHT DOUBLE,
Thanks. I had to make some changes to get it to run:
CREATE TABLE TBLPATIENT
 PATID VARCHAR2 (20),
 EPISODE_NUMBER BINARY_DOUBLE, -- There's no DOUBLE data type in SQL
 DATE_OF_DISCHARGE DATE
DROP TABLE tblprogressnotes;
CREATE TABLE TBLPROGRESSNOTES
 PATID VARCHAR2 (20),
 EPISODE_NUMBER NUMBER, -- Most people use NUMBER for all numeric types
 ENTRY_DATE DATE, -- DATA_entry date is a good name, too, just be consistent
 GIRTH NUMBER, -- Can't average VARCHAR2s
 HEIGHT NUMBER,
 WEIGHT NUMBER -- no comma here
INSERT INTO TBLPATIENT VALUES (1, 1);
INSERT INTO TBLPATIENT VALUES (2, 1);
// For the first 3 records, the height stays the same, but the girth and weight values are variable on the same day
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/01/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 36, 66, 184);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/01/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 35.5, 66, 185);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/01/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 35, 66, 184.5);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/18/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 36, 66, 187);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/31/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 36.5, 66, 190);
// For the last 3 records, the girth and height stay the same, but the weight is variable on the same day.
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/03/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 32, 66, 137.5);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/08/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 32.5, 66, 138);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/19/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 31, 66, 134);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/19/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 31, 66, 133.5);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/19/2013 00:00:00', 'MM/DD/YYYY HH:MM:SS'), 31, 66, 134.5);
INSERT INTO TBLPATIENT VALUES (1, 1, NULL);
-- If the table has 3 columns, ^^^^^^ INSERT 3 values (or say which columns you're INSERTing)
INSERT INTO TBLPATIENT VALUES (2, 1, NULL);
// For the first 3 records, the height stays the same, but the girth and weight values are variable on the same day
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/01/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 36, 66, 184);
-- MM = month ^^ ^^ MI = minutes
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/01/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 35.5, 66, 185);
-- Hour 00 ^^ not valid for HH ^^^^ use HH24 instead
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/01/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 35, 66, 184.5);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/18/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 36, 66, 187);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/31/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 36.5, 66, 190);
// For the last 3 records, the girth and height stay the same, but the weight is variable on the same day.
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/03/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 32, 66, 137.5);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/08/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 32.5, 66, 138);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/19/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 31, 66, 134);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/19/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 31, 66, 133.5);
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/19/2013 00:00:00', 'MM/DD/YYYY HH24:MI:SS'), 31, 66, 134.5);This seems to be different from the sample data you posted earlier. You didn't say what results you want from this data, so I don't know if this gets them or not:
SELECT
 P.PATID,
 P.EPISODE_NUMBER,
 P.DATE_OF_DISCHARGE,
 M.ENTRY_DATE,
-- M.ENTRY_TIME, -- Not needed (not present in simplified sample data, anyway)
 AVG (M.GIRTH) AS avg_girth, -- AVG added
 AVG (M.HEIGHT) AS avg_height,
 AVG (M.WEIGHT) AS avg_weight
FROM
 TBLPATIENT P LEFT OUTER JOIN
 TBLPROGRESSNOTES M ON
 (P.PATID = M.PATID) AND
 (P.EPISODE_NUMBER = M.EPISODE_NUMBER)
WHERE
 P.DATE_OF_DISCHARGE IS NULL AND
 M.ENTRY_DATE BETWEEN (SYSDATE - 60) AND SYSDATE AND
 M.HEIGHT != 0 AND -- This site won't display the other inequlaity operator
 M.WEIGHT != 0
GROUP BY -- GROUP BY clause added
 P.PATID, -- Includes all columns from the SELECT clause that
 P.EPISODE_NUMBER, -- are not aggregated
 P.DATE_OF_DISCHARGE,
 M.ENTRY_DATE
ORDER BY
 P.PATID, -- No column called patIENTid
 M.ENTRY_DATE
-- , M.ENTRY_TIME
;As you can see, it's very close to what you posted, and to what I suggested earlier: use AVG on the columns that you want to average, and GROUP BY the other columns. I marked all the places I changed with in-line comments.
Since the hours, mintues and seconds of entry_date are always 00:00:00, then there's no need to use TRUNC (entry_date). Using it unnecessaily won't change the results, it will only waste a little time.
By the way, if you omit the hours, minutes and seconds in TO_DATE, they default to 00:00:00, so you could make the insert statements a little simpler like this:
INSERT INTO TBLPROGRESSNOTES VALUES (1, 1, TO_DATE('01/01/2013', 'MM/DD/YYYY'), 36, 66, 184);Output fro the query above:
` EPISODE
PATID _NUMBER DATE_OF_DI ENTRY_DATE AVG_GIRTH AVG_HEIGHT AVG_WEIGHT
1 1 01/01/2013 35.5 66 184.5
1 1 01/03/2013 32 66 137.5
1 1 01/08/2013 32.5 66 138
1 1 01/18/2013 36 66 187
1 1 01/19/2013 31 66 134
1 1 01/31/2013 36.5 66 190

First DSLR for filming

Similar Messages

Maybe you are looking for