FMW rpm dependency

The Oracle® Fusion Middleware System Requirements and Specifications for Oracle Identity and Access Management 11g Release 2 (11.1.2.1) documentation lists a set of Linux packages, included at the end of this post, as dependencies in installing Fusion Middleware products on RHEL 6.4.
On a 64-bit operating system, do I require the 32-bit or the 64-bit version of the package where the platform is not explicitly specified (e.g. libaio)?
Thanks a bunch!
Ingo
binutils-2.20.51.0.2-5.28.el6
compat-libcap1-1.10-1
compat-libstdc++-33-3.2.3-69.el6 for x86_64
compat-libstdc++-33-3.2.3-69.el6 for i686
gcc-4.4.4-13.el6
gcc-c++-4.4.4-13.el6
glibc-2.12-1.7.el6 for x86_64
glibc-2.12-1.7.el6 for i686
glibc-devel-2.12-1.7.el6 for i686
libaio-0.3.107-10.el6
libaio-devel-0.3.107-10.el6
libgcc-4.4.4-13.el6
libstdc++-4.4.4-13.el6 for x86_64
libstdc++-4.4.4-13.el6 for i686
libstdc++-devel-4.4.4-13.el6
libXext for i686
libXtst for i686
openmotif-2.2.3 for x86_64
openmotif22-2.2.3 for x86_64
redhat-lsb-core-4.0-7.el6 for x86_64
sysstat-9.0.4-11.el6
uln-internal-setup-1.0.1-1.el6.noarch.rpm

The rpm utility does not resolve any software dependencies and is not the recommended tool to install software since RHEL 5. You can use the yum utility instead, which automatically resolves software dependencies.
If you do not specify the platform architecture, yum will select the appropriate package for the current platform. Since software libraries are usually backward compatible, you should not specify a particular version, unless it is absolutely necessary.
In your case:
yum install binutils compat-libcap1
yum install compat-libstdc++-33 compat-libstdc++-33.i686
yum install gcc gcc-c++ glibc glibc.i686
yum install libio libaio-devel libstdc++ libstdc++.i686
etc.
For example:
[root@vm21 ~]# yum install glibc.i686
Loaded plugins: security
Setting up Install Process
Resolving Dependencies
--> Running transaction check
---> Package glibc.i686 0:2.12-1.107.el6_4.5 will be installed
--> Processing Dependency: glibc-common = 2.12-1.107.el6_4.5 for package: glibc-2.12-1.107.el6_4.5.i686
--> Processing Dependency: libfreebl3.so for package: glibc-2.12-1.107.el6_4.5.i686
--> Processing Dependency: libfreebl3.so(NSSRAWHASH_3.12.3) for package: glibc-2.12-1.107.el6_4.5.i686
--> Running transaction check
---> Package glibc-common.x86_64 0:2.12-1.107.el6_4.4 will be updated
--> Processing Dependency: glibc-common = 2.12-1.107.el6_4.4 for package: glibc-2.12-1.107.el6_4.4.x86_64
---> Package glibc-common.x86_64 0:2.12-1.107.el6_4.5 will be an update
---> Package nss-softokn-freebl.x86_64 0:3.12.9-11.el6 will be updated
---> Package nss-softokn-freebl.i686 0:3.14.3-3.el6_4 will be installed
etc.

Similar Messages

Kernel-devel-2.6.18-238.el5.x86_64.rpm dependency for dkms

Hi,
I am trying to install VirtualBox-4.1-4.1.8_75467_rhel5-1.x86_64.rpm on Red Hat Enterprise Linux Server release 5.6.
During installation it fails with following error:
=================================
sh-3.2# rpm -i VirtualBox-4.1-4.1.8_75467_rhel5-1.x86_64.rpm
warning: VirtualBox-4.1-4.1.8_75467_rhel5-1.x86_64.rpm: Header V4 DSA signature: NOKEY, key ID 98ab5139
Creating group 'vboxusers'. VM users must be member of that group!
No precompiled module for this kernel found -- trying to build one. Messages
emitted during module compilation will be logged to /var/log/vbox-install.log.
Stopping VirtualBox kernel modules [ OK ]
Uninstalling old VirtualBox DKMS kernel modules [ OK ]
Trying to register the VirtualBox kernel modules using DKMS [FAILED]
(Failed, trying without DKMS)
Recompiling VirtualBox kernel modules [FAILED]
(Look at /var/log/vbox-install.log to find out what went wrong)
===========================
So I tried installing dkms and it failed with following error.
=========================================================
sh-3.2# rpm -i dkms-2.1.1.2-1.el5.rf.noarch.rpm
warning: dkms-2.1.1.2-1.el5.rf.noarch.rpm: Header V3 DSA signature: NOKEY, key ID 6b8d79e6
error: Failed dependencies:
kernel-devel is needed by dkms-2.1.1.2-1.el5.rf.noarch
=======================================================
Now I am not able to find rpm for kernel-devel (kernel-devel-2.6.18-238.el5.x86_64.rpm ).
Any idea?

houst0n wrote:
There is no 'kernel-devel' package on redhat, if you need the kernel source then you need to pull down a srpm.Of course there's a kernel-devel package. I use it all the time.
However, the Red Hat (and associated downstream compilations like CentOS and Oracle Linux) don't use DKMS. What you want is to install kernel-devel so it builds the full kernel modules, not the DKMS module. We provide the kernel-devel package for Oracle Linux on the install media, on ULN and via our public yum repository at http://public-yum.oracle.com

Using a 9205 to measure RPM

I have not used labview in over 10 years but now have an application that requires but I am more then rusty. I am trying to measure RPM using a 9205 module and I am sure there is a way to do it. I have a pulsed voltage output from my measurement circuit and so far I am capturing the voltage. Can someone suggest a way to convert these voltage pulses to an RPM value. I am sure some type of leading edge counter would work.
Thanks

Not the cheapest route but there is a SCXI card that measures frquency.
http://sine.ni.com/nips/cds/view/p/lang/en/nid/1661
There may be some other frequency cards this is one I have used in the past. With this card you can create a virtual channel and ask it what frequency the analog signal is going into it. From here there is a conversion from frequency to RPM depending on the type of resolver or hall signal you are using to generate that signal.
This method is the easiest but the cheapest would be to get a cheap AI DAQ device that can measure several times faster than the generated signal (nyquist theorem) then analyze the series of AI reads to determine the frequency. Then convert frequency to RPM. Depending on the signal a USB DAQ device might work, if not a PCI or PXI + MXI card would still probably be cheaper than the SCXI route.
Unofficial Forum Rules and Guidelines - Hooovahh - LabVIEW Overlord
If 10 out of 10 experts in any field say something is bad, you should probably take their opinion seriously.

CPU Fan is always at 5000+ RPM!!!

So I did an upgrade today. I now have a P4 3.0E (prescott) processor, an MSI 865PE Neo2-PFS (Platinum Edition), 1GB of DDR400 RAM, and a new pci-firewire card
The minute I hooked this sucker up everything worked, but the cpu fan is always at 5000+ RPM (as reported in the bios pc health monitor). I thought the motherboard lowered the cpu rpm depending on the temperature, but apparently it's CoreCenter. I use linux and obviously cannot install CoreCenter. Is there any other way I can get my fan to lower it's speed? maybe an equivalent linux software that does the job?

I Agree With Mr. Moleman, as with all of the Heat related Issues that have been Plaguing the Prescott, I would NOT Be Supprised if it is Written into the Latest Precott Microcode in the BIOS, to Run the Stock INTEL Thermal Solution at 100% Speed.................Sean REILLY875

How to install 9ias on Linux quick guide

I have installed the linux version of application server a couple of times now. I have noted all the steps I took to complete the installation. Everything works except for reports. Anyway here are the steps I took to get it working. Hope it helps. Note: This is for RedHat Advanced Server 2.1, I have created a user called oracle9 to own the software. Please feel free to add comments etc.
1. Install RedHat Linux Advanced Server 2.1 - install all the packages.
2. Edit files in the following directory to allow connectivity, must be as ROOT user.
/etc/xinetd.d
3. Edit the directory permissions for /usr/local and /usr/local/src as ROOT user.
This is we can install files and utilities in these directories. Also create an oracle directory to
store the software. I created /usr/local/oracle/orahome1.
chmod 777 /usr/local
chmod 777 /usr/local/src
chmod 777 /usr/local/oracle
chmod 777 /usr/local/oracle/orahome1
4. Add /usr/sbin to the PATH environment variable so that most commands are accessible.
To do this edit the /etc/profile file.
Add the following line
PATH="/usr/bin:$PATH:/usr/X11R6/bin:/usr/sbin:/sbin"
5. Check kernel and glibc versions by running uname. ie
Kernel check is uname -r
OR
use rpm -q kernel
rpm -q glibc
The versions shoule be as follows
kernel = 2.4.9-e.3
glibc = 2.2.4-26
6. System Wide Ulimit and Swap File Settings.
Should be as follows.
time unlimited
file unlimited
data 1048576
stack 131072
memory unlimited
coredump 4194303
nofiles 2048
There are several files to enable these settings.
First we edit the /etc/security/limits.conf file to set the required limits.
File should look like this.
# /etc/security/limits.conf
#Each line describes a limit for a user in the form:
#<domain> <type> <item> <value>
#Where:
#<domain> can be:
# - an user name
# - a group name, with @group syntax
# - the wildcard *, for default entry
#<type> can have the two values:
# - "soft" for enforcing the soft limits
# - "hard" for enforcing hard limits
#<item> can be one of the following:
# - core - limits the core file size (KB)
# - data - max data size (KB)
# - fsize - maximum filesize (KB)
# - memlock - max locked-in-memory address space (KB)
# - nofile - max number of open files
# - rss - max resident set size (KB)
# - stack - max stack size (KB)
# - cpu - max CPU time (MIN)
# - nproc - max number of processes
# - as - address space limit
# - maxlogins - max number of logins for this user
# - priority - the priority to run user process with
# - locks - max number of file locks the user can hold
#<domain> <type> <item> <value>
#* soft core 0
#* hard rss 10000
#@student hard nproc 20
#@faculty soft nproc 20
#@faculty hard nproc 50
#ftp hard nproc 0
#@student - maxlogins 4
oracle9 - nofile 65536
* - nofile 65536
* - nproc 65536
* - cpu unlimited
* - fsize unlimited
* - data 1048576
* - stack 131072
* - memlock unlimited
* - core 4194303
# End of file
We now need to edit the /etc/sysctl.conf file to set the system wide ranges as ROOT user.
File should look like this.
# Disables packet forwarding
net.ipv4.ip_forward = 0
# Enables source route verification
net.ipv4.conf.default.rp_filter = 1
# Disables the magic-sysrq key
kernel.sysrq = 0
net.ipv4.ip_local_port_range = 1024 65000
fs.file-max = 65536
kernel.sem = 100 32000 100 100
kernel.shmmax = 2147483648
kernel.shmmni = 4096
kernel.shmall = 2097152
Now we need to edit the /etc/profile file to enable the settings when a user logs in.
The file contents should be modified as follows.
# No core files by default
ulimit -S -c 1000000 > /dev/null 2>&1
#Set the file handels
#echo 65536 > /proc/sys/fs/file-max
ulimit -n 65536 > /dev/null 2>&1
#Set the socket range
#echo 1024 65000 > /proc/sys/net/ipv4/ip_local_port_range
# Set the number of processes for per user
ulimit -u 16384 > /dev/null 2>&1
Kernel Parameters
Change to following directory /proc/sys/kernel and type following
echo 250 32000 32 128 > sem
echo 2147483648 > /proc/sys/kernel/shmmax
echo 4096 > /proc/sys/kernel/shmmni
echo 2097152 > /proc/sys/kernel/shmall
7. Install the ksh package if you have not already installed it on your machine.
Oracle Corporation recommends installing one of the following ksh packages:
pdksh-5.2.14-13 or other compatible packages.
RPM file is available from www.redhat.com
as root user type
rpm -i pdksh-5.2.14-16.i386.rpm
8. On Linux, port number 389 is reserved in the /etc/services file.
If you want Oracle9iAS to install using the default port number for Oracle Internet Directory,
delete the entries in the /etc/services file.
Note:
You must remove all lines containing the port number 389 from
the /etc/services file if you want to use that port number.
Attempting to comment out lines containing 389 does not free the port
9. Install JDK 1.3.1 for Linux.
This is available from java.sun.com. Although it is also included with Linux IAS9I R2
Install the JDK to /usr/local/jdk
Add the following to the /etc/profile file, and also add to path
CLASSPATH="/usr/local/jdk/lib"
LD_LIBRARY_PATH="/usr/local/jdk/jre/lib/i386:/usr/local/jdk/jre/lib/i386/classic:
/usr/local/jdk/jre/lib/i386/native_threads"
EXPORT CLASSPATH
EXPORT LD_LIBRARY_PATH
10. Add the following groups as ROOT user
oinstall, dba
groupadd oinstall
groupadd dba
11. Add oracle user to groups oinstall and dba as ROOT user
usermod -g oinstall -G dba,oracle9 oracle9
12. Apply a patch for binutils rpm:
I had to get this from metalink. Not sure where else it is available.
Run following command to get installed version of binutils rpm.
prompt> rpm -qa | grep binutils
binutils-2.11.90.0.8-12
Please note down the binutils rpm version that is shown as the output of the above command.
If the operating system is installed from the RedHat 2.1 Advanced Server CDs,
you will have binutils-2.11.90.0.8-12 version installed.
You might have newer version of binutils rpm depending on your further configuration
after default OS install. If the binutils rpm version is different from 2.11.90.0.8-12,
please download that rpm.
Upgrade to binutils-2.11.90.0.8-13 version using following command (as root user):
prompt> rpm -Uvh --force binutils-2.11.90.0.8-13.i386.rpm
13. Edit Local Hosts file
Edit so that the host is in the following format
# Do not remove the following line, or various programs
# that require network functionality will fail.
127.0.0.1 localhost.localdomain localhost
192.168.3.69 lon-ias01.closepf.local lon-ias01
192.168.3.66 lon-ias02.closepf.local lon-ias02
14. Create Symbolic Link from /sbin/fuser file to /bin/fuser by entering the following command.
cd /bin
ln -s /sbin/fuser
15. Rename Linux Ldap programs
rename the ldapadd, ldapsearch, ldapmodify etc located in /usr/bin
mv ldapadd ldapadd.bak
mv ldapdelete ldapdelete.bak
mv ldapmodify ldapmodify.bak
mv ldapmodrdn ldapmodrdn.bak
mv ldappasswd ldappasswd.bak
mv ldapsearch ldapsearch.bak
16. Unset your oracle home environment variable.
unset ORACLE_HOME
17. Set your TMP, TMPDIR and TEMP environment variables.
These are located in /etc/profile
TMP="/tmp"
TMPDIR="/tmp"
TEMP="/tmp"
export TMP TMPDIR TEMP
18. Make sure you have the following X11 library XFree86-devel-4.1.0-25.i386.rpm,
which can be found of disk2 of the RedHat Advanced Linux CD v2.1. This is needed
by the linking process.
As ROOT user.
mount the cdrom.
cd /mnt/cdrom/RedHat/RPMS
rpm -Uvh XFree86-devel-4.1.0-25.i386.rpm
19. Install the application server as per the offficial install instructions. You should only have
to use mount_point/runInstaller and follow the prompts.
21. If it installs then run the interoperability patch.
22. Should be working?!?
19. To Remove an Install
WARNING : Please note that by following the processes defined
below, ALL Oracle products on the system will be cleaned
up and will not be usable. Please do not follow these steps if you do
not want to remove any Oracle Products
1. Deinstall using installer
2. Stop all running processes from the install.
3. Delete the oracle directory under /var/opt as root user
4. Delete the complete oraInventory directory
5. Delete all directories and files from ORACLE_HOME directory
6. Cleanup files under /tmp and /var/tmp as root user
8. Remove emtab in the /etc directory
9. Remove oracle files in /usr/local/bin
Hope it works.

ummm...
chmod 777 /usr/local
chmod 777 /usr/local/src
chmod 777 /usr/local/oracle
chmod 777 /usr/local/oracle/orahome1
Why on earth would you do that??? There is NO need for >that, not to mention it being a HUGE security issue. I >have an offical doc on installing and configuring 9iAS >on Linux (includes information on as 2.1 install). I >will post this evening.Your quite correct, this section could probably be trimmed from the guide. At the time it was written it was used on a development box, on a production box this would not be done. Also to get this install working when Oracle first released it we were trying anything and everything to get it working, it took around 3-4 weeks of installing, reinstalling, serveral thounsand tar's and wasted weekends. I am pretty confident the instructions will work on rhas 2.1, it probably needs to be looked at again to trim away steps that aren't needed now.
Looking forward to seeing your guide :-)

How can I control a dc motor speed using an optical switch?

I am trying to use LabVIEW to create a VI that controls the speed of a DC motor. The system needs to have an user set rpm and the DC motor needs to adjust the duty cycle to obtain the correct rpm dependant on the load. A disk with holes and an optical switch is being used to measure rpm.
The current problem is that I cannot get the rpm based on the optical switch.
Thanks for your help!
Attachments:
Speed reg.vi ‏183 KB

The error for the samples to write does not appear after redoing the vi. Thanks. The controller seems to be working mostly.
However, the issue with the Tone Measurement reading inaccurately at low frequencies still exist. Any ideas?
I have attached the latest vi.
Thanks again!
Attachments:
speed_reg_v2013-05-07.vi ‏183 KB

Installation of forms 11g release 2 on windows 7 64 bit client

Hi,
I am trying to install forms and reports 11g release 2 on my windows 7 64 bit client.
When I tried to install it, I got a message Weblogic should be installed first.
In the Oracle site there are many versions of Weblogic. Which should I install?
Thanks
Rani

Rani,
Oracle has rebranded the Oracle Developer Suite (ODS) as Fusion Middleware (FMw). Part of the evolution of the suite has been the replacement of the OC4J Container used by ODS to use WebLogic Server. Unfortunately, in order to install the FMw Forms and Reports builders you must also install the WebLogic Server (WLS) on your development workstation. Each version of FMw is dependent on a specific version of the WLS. Here is the basic break down:
WLS 10.3.2 with FMw R1 (11.1.1.2)
WLS 10.3.3 with FMw R1 (11.1.1.3)
WLS 10.3.4 with FMw F1 (11.1.1.4)
WLS 10.3.5 with FMw R2 (11.1.2)
As you can see, you will need to download and install the WLS 10.3.5 before you can install FMw R2. Make sure you do not run the WLS configuration step at the end of the instllation. When you install FMw r2, it will perform the necessary configuration the WLS and Forms and Reports Services.
Hope this helps,
Craig B-)
If someone's response is helpful or correct, please mark it accordingly.

My macbook pro is hot?

I just bought a macbook pro 13'' non retina display. (I am using it now) so far it has been very good. It is smooth and quick but I am worried about the heat. I have it in a very airated area and it is sitting on a desk. I downloaded istat as a widget and found these things. The exhaust fan is travelling at 2000rpm, it says it is 32 degrees celcius, the ambient is 33 degrees celcius, everything else is about 30 degrees and my mem module A1 is 40 degrees. Anyway I am worried because it is very airated, I am not doing much on it, and not much is in activity log yet it is very hot at the bottoM. Were the tempratures I stated quite normal, and if they are not do I have a deffective laptop?

The data that you initially reported shows that your MBP is operating normally and as expected. The fan speed will range from a low of 2000 rpm to about 6200 rpm dependent upon the heat being generated in the MBP.
Heat within the MBP will range from the high 30's° c to about 105° c when thermal shutdown will occur. When performing lightweight activity such as word processing and Internet browsing, one may expect temperatures in the 40* - 50* c range. If one is engaged in games, using Skype or other heavy weight applications, temperatures in the 90* c range are common. Fan speeds naturally will increase in those conditions.
This is an image of my MBP iStat pro as I write this response:
Ciao.

Late 2008, Macbook Fan issues?

Hello,
I am curious to know if anyone has experienced problems with their fan?
I had a power failure at my house, before the failure, the Macbook was running fine as usual, after restarting, Fan continues to run?
Through iStat I can see that the temp is 35 degrees and the dual cpu usage is at little to none? Is this normal, will the fan return to its quiet mode?
Thank you

I'm not sure I understand. The fan always runs continuously. It should idle around 2000 RPM and will increase to 6000 RPM depending upon CPU and GPU activity.
If your fan is running at high speed continuously, then open Activity Monitor in the Utilities folder. Select All Processes from the Processes drop down menu. Click twice on the CPU column to display in descending order. Look for a process consuming a large amount of CPU time. If you find one then select it and click on the Quit icon in the toolbar, then click on the Force Quit button. See if that fixes the problem. Otherwise you may have some file corruption that may have been caused by the power outage. You should try the following in this case:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer. Now restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.

What is a safe temperature for the CPU?

My new MBP's CPU is running at around 55-65 degrees idle, and upper 70's to low/mid 80's when doing anything intensive. (According to iStat widget)
I was wondering if this is normal or safe, as according to
http://www.hardwaresecrets.com/article/366/2
The max temperature should be 60.1 degrees Celsius
Message was edited by: CCDwyer

My pleasure. Thanks for the star!
By the way, the temps you report are normal. Above ~65 C the fans speed to to provide more cooling (they idle at ~1000 rpm or ~2000 rpm depending on model, and have a max speed of 6000 rpm.

How to validate array fields in struts

hi
iam working on struts. i have array fields in my jsp page. i wanna do validations for those fields. iam specifying name of the field in the validation.xml. but iam not getting correct validations. how can i have proceed in the case of array fields.
plzz help me
vamsi

hi thank you for your help
iam using the same syntax only. but iam not getting iam sending my jsp and xml files
<body>
<logic:messagesPresent>

<html:messages id="error">
<li><%=error %></li>
</html:messages>

</logic:messagesPresent>
<html:form action="/wofinal" onsubmit="return validateWofinalForm(this)">
<% System.out.println("true"); %>

Work Order Release
 
<table border="1" width="70%" align=center>
 <tr>
 <td width="50%">
 Select Work Order Number 
 </td>
<td width="50%" align=left>
<%
 String worder_no=(String)session.getAttribute("worder_no");
 String selected=(String)session.getAttribute("selected");
%>
 <%= worder_no %>
 <html:hidden property="worder_no" value="<%= worder_no %>" ></html:hidden>
</td>
</tr>
<tr>
 <td width="50%">
 Number
 of Candidates Got Selected 
 </td>
 <td width="50%">
 <%= selected %>
 <html:hidden property="selected" value="1"></html:hidden>
</tr>
<tr>
 <td width="50%" align="right">Remarks </td>
 <td width="50%"><html:text maxlength="300" property="remarks" size="50"></html:text>
</tr>
</table>
 
<table border="1" width="90%" height="44" align="center">
 <tr>
 <td width="5%" valign="middle" align="center" height="38">
 S.No</td>
 <td width="16%" valign="middle" align="center" height="38">Name</td>
 <td width="16%" valign="middle" align="center" height="38">Qualification</td>
 <td width="12%" valign="middle" align="center" height="38">Date of
 Commencement</td>
 <td width="12%" valign="middle" align="center" height="38">Date of
 Completion</td>
 <td width="10%" valign="middle" align="center" height="38">Rate per MM</td>
 <td width="5%" valign="middle" align="center" height="38">No. of MMs</td>
 </tr>
 [u] Here iam getting problem in the validation of below fields[/u]
 <% int count=Integer.parseInt(selected); %>
 <% for(int i=1;i<=count;i++) {
 String st=""+i;
 %>
 <tr>
 <td width="5%" align="center" height="38"><html:text property="sno" value="<%= st %>" onfocus="this.blur()" maxlength="2" size="2"/></td>
 <td width="17%" valign="middle" align="center" height="38"><html:text property="name" value="" ></html:text></td>
 <td width="10%" valign="middle" align="center" height="38"><html:text property="qual" value="" size="20"></html:text></td>
 <td width="10%" valign="middle" align="center" height="38"><html:text property="comm" value="" maxlength="10" size="15"></html:text></td>
 <td width="10%" valign="middle" align="center" height="38"><html:text property="comple" value="" maxlength="10" size="15"></html:text></td>
 <td width="10%" valign="middle" align="center" height="38"><html:text property="rpm" value="" size="10"></html:text></td>
 <td width="7%" valign="middle" align="center" height="38"><html:text property="mm" value="" maxlength="3" size="5"></html:text></td>
 </tr>
 <% } %>
 </table>
 <html:submit/>
</html:form>
</body>
</html:html>[b]and my struts-config file is
 <form-beans>
 <form-bean name="wofinalForm"
 type="bean.WOfinalForm" >
 </form-bean>
 </form-beans>
 <action-mappings>
 <action path="/wofinal"
 type="bean.WOfinalAction"
 name="wofinalForm"
 scope="request"
 validate="true"
 input="/worder_final.jsp">
 <forward name="SUCCESS" path="/index.jsp" redirect="true"/>
 <forward name="FAILURE" path="/worder_rel.jsp" redirect="true" />
 </action>
 </action-mappings>
and my validation.xml file is
<formset>
 <form name="wofinalForm">
 <field property="name"
 depends="required">
 <arg key="finalform.name" />
 </field>
 <field property="comm"
 depends="required,date">
 <arg key="finalform.comm"/>
 <arg1 key="${var:datePattern}"
 name="datePattern" resource="false" />
 <var>
 <var-name>datePattern</var-name>
 <var-value>dd/mm/yyyy</var-value>
 </var>
 </field>
 <field property="rpm"
 depends="required,integer">
 <arg0 key="finalform.rpm"/>
 <arg0 key="finalform.rpm" />
 </field>
 <field property="mm"
 depends="required,integer">
 <arg0 key="finalform.mm"/>
 <arg1 key="finalform.mm" />
 </field>
 </form>
</formset>in the jsp page iam using loop to display fields
in the validations of those fields iam getting error.
plzz help me.
vamsi

Freeze-up after RAM and Leopard Install

Machine: iMac G4 1.25GHz 20-inch Flat Panel
Problem: Computer “freezes” after going through a normal startup. I believe that this is related to overheating. I have installed a new fan, the fan runs, but it does not appear to be running at a high enough speed to cool the CPU. The air output is very low when using the “feel” test (placing my hand over the vents). All the fan wires appear to be connected correctly. I have applied thermal paste and tightened the bottom housing bolts down securely. I have also reset the PMU and the PRAM. Any other suggestions? Should I toss it from a second story window?

I am not familiar with tearing down an iMac, so I have no idea what the wiring looks like. I would presume you looked for this information via Google or ifixit.com.
As for monitoring software you have lots of choices, but i think the best of the lot would be iStatMenus or iStat Pro - VersionTracker or MacUpdate. The former can put monitors in the menubar while the latter is a Dashboard widget providing the same information but as a widget. Both fully compatible.
Couldn't tell you what the default idle is on an iMac fan but most likely between 1000 and 2000 RPM depending upon model. Mac laptops idle at around 2000 RPM.

Versions of PHP and libxml2 for Linux Redhat

I installed PHP 5.3.19. I had two choices from http://php.net/downloads.php. Version 5.4 or 5.3. The latest version of libxml2 available for RHEL 5.5 is 2.6.26 release 2.1.15. Should I go with this one or should I download a later version for Fedora, and if so which one, or should I download an earlier version of PHP to go with libxml2 2.6.26 release 2.1.15 and if so which one?
Edited by: 944901 on Dec 11, 2012 11:06 AM

- Oracle Linux 5 is also available from the repo I mentioned.
- There are 8 extensions in the PHP source that require libxml2. I don't know which one(s) you want. I have built some in the past on OL. I expect many other people have built PHP and some or all of the XML-based extensions on RH or OL 5.x. You won't have difficulty testing it yourself since building command line PHP takes only a few steps; just don't pass an with-apxs2 flag to PHP's "configure" command. You can choose which extensions you want, such as with-simplexml (which is default, BTW)
- The PHP RPMs will not install on OHS because the RPMs depend upon, and install into, the httpd RPM
- The OHS web page you mentioned wasn't written by me (and is slightly obsolete regarding header files, though I've often requested the owner update it). The best instructions for installing on OHS are in the newly updated The Underground PHP and Oracle Manual. See page 86.
- Again, I'd recommend using PHP 5.4.

Who do I blame for poor DL performance?

FF 3.6.3 Over the last few months I (and my wife ) have had slow down and others problems with Internet connection. Most common are "server not found" or "unable to connect" messages but if I hit the Try Again button 1, 2, 3, 4 or ... times the web site appears. I can tell when I have succeeded when the message in the tab changes from "problem loading page" to the title of the web site. After that loading can be very fast but lately pretty slow. The green progress bar seems to go to 3/4 immediately and then crawls minutely. The most annoying new occurrence is that sometimes when the site loads there are no graphics! My wife uses IE (on a different computer) and has experienced similar messages and performance so I don't think FF is to blame. Download speed (speakeasy) is reported at 6-7mb. So who do I blame; modem, router, maybe excessive noise on the line, the Comcast servers or some other factor? Thanks for any input.
== Operating system ==
XP

You would be better off using one of the fan control utilities, SMCFanControl or FanControl - VersionTracker or MacUpdate - than that old method.
You might open Activity Monitor and check for any process that's using an inordinate amount of processing time.
Normal operating temperatures range from 45ºC-85ºC depending upon CPU load and ambient room temperature. Somewhat higher idle temperatures may occur for the faster CPUs. The fans idle at 2,000 RPM and max out at 6,000 RPM depending upon how hot the computer gets.

Fan controller question

This is probably a quick and stupid question, I am running some vantec 80mm tornadoes which are a bit loud. Well actually if you can imagine a boeing 737's engines powering up you know how load these fans are. Seriously though they are about 71 Dcb. So I would like to control their rpm depending on my needs. My question is, can the K7N2-ILSR only support two fans directly off the motherboard (the nb fan and cpu). And I have to buy a fan controller right? Or is there another way I am not aware of.
Im sure some people will tell me I shouldnt have bought these fans, but they really do push a lot of air,
Thanks everyone

I have a CoolerMaster Aerogate II control box.
It looks neat, it monitors temperatures of 4 devices and you can run your fans to it and control the speeds with a dial, as longs as the fan supports speed control.
The temps are accurate, while I'm in the bios screen I saw that the Aerogate was reporting the exact same CPU temperature as the bios was, but Aerogate was refreshing faster. (it's a real time). I have the Aerogate's diode run underneath the heatsink, right next to the CPU die.
The Aerogate has a LED screen that's blue, and the devices are selected through "channel switches."
The Aerogate cost 45 dollars (USD).
It's my new favorite toy.

FMW rpm dependency

Similar Messages

Maybe you are looking for