Frequency domain in dsp module with speedy-33 target

Hi,
I am using the speedy-33 to generate a sine wave, square wave, sawtooth wave, and a ramp wave. I am doing an FFT analysis on them to display the signals in the frequency domain. However the x-axis displays the sample number for both the time domain and frequency domain. Is there a way to moake it so the x-axis is displaying either the time in the time domain or frequency in the frequency domain.
Thanks for your help.

Hi Rcarr,
I'm a little confused as to what time data you expect to see? The signal you are generating is just and array of numerics, but there is sampling information used to create that signal. Do you want to have the signal start at 0 and display the time that has elapsed?
In short, you can't do this within a VI running on the Speedy-33. However if you pass data to a host VI then you can manipulate the graph. You can do this by calculating a multiplier for the x-scale of your graph based on the dx of you sampling. There is a property node for the graph where you can set this multiplier but you can only use it on a host VI not running on the Speedy-33.
If you use the Simulate Signal Express VI you will have to create a constant that is the same value as the property you specify within the properties. You might consider using the EMB sine wave.VI that has an input for sampling rate and number of samples. You can then take the reciprocal of the sampling frequency and run that to the multiplier input by passing it to your host VI.
Let me know if I can help any further or if you have any questions.
Sappster

Similar Messages

Dsp module with sound and vibration

Is possible to be employed with Sound and Vibration at the DSP module??
Thank you

Sorry,
it's not possible to use Sound and Vibration functions with DSP. But here you can find a list of all the function you can use in DSP enviroment:
http://www.ni.com/pdf/products/us/2005_5416_821_101_D.pdf
Clara
AE Manager
NI Italy

Labview dsp module with tidsk 6713

Hi,
I'm working with TI DSK6713 board on Labview 8.6.1 version with the Labview dsp module 8.6.
The idea is to delegate computationally heavy FFT operation to DSP processor computing it many times in a loop.
As FFT is tailored for DSP and, in fact, Labview DSP tool has build-in FFT module, it should operate much
faster on DSP rather PC. So I expect to have acceleration here, and I don’t see that so far.
Does anyone observe performance accelaration with labview dsp compared to labview only performance ? What are the tools for measuring timing statistics on labview dsp ?
Thanks.

Hey Salander,
I am an applications engineer here at National Instruments and would like to get a little more information from you to see if I can help you with your issue. I am not particularly familiar with the TI DSK6713 as it is a third party product. It seems to me like you think that since the TI DSK6713 has a DSP processor it should hypothetically run LabVIEW DSP faster than your PC. I am wondering if the TI DSK6713 is fundamentally different than any other board.
Here is a link to the manual for LabVIEW DSP that might have some helpful information for you that could shed some light on your issue:
http://digital.ni.com/manuals.nsf/websearch/AB1AC84DD6DD3CEF86257456006B1FF0
Good Luck,
Doug B
Applications Engineer
National Instruments
Applications Engineer
National Instruments

Numerisation of Acquired Data and Transforming into Frequency domain to process it with some mathematical expressions

Hi everyone,
I've been trying to manage some signal processing stuff, I use mathscript node for it; due to the node, i have to transform the data set into numerical values. Due to my research, i should do my processing in frequency domain.
I did a VI, but i dont think it will work properly when i will use it with acquired data. The VI in the attachment has four dummy-signal sources, sines, consider these as analog input channels. The main question is actually how to process acquired data with numerical operations. And how to properly transform the time domain series into "numerical" frequency domain array.
Take a look at the example in the attachment. The other one is mathematical expression of the process.
Thanks,
OZGUR
Attachments:
sample.vi ‏204 KB
mathematical.png ‏103 KB

Motorbreath,
Here are some examples on how to use LabVIEWs graphcial coding to get things into the Frequency domain:
https://decibel.ni.com/content/docs/DOC-9981
http://zone.ni.com/devzone/cda/tut/p/id/13042
http://zone.ni.com/devzone/cda/tut/p/id/7111
http://zone.ni.com/devzone/cda/epd/p/id/2904
But essentially you are going to want to use the FFT VIs
http://zone.ni.com/devzone/cda/tut/p/id/4278
http://zone.ni.com/devzone/cda/tut/p/id/4541
http://zone.ni.com/devzone/cda/tut/p/id/3342
https://decibel.ni.com/content/docs/DOC-6390
I hope this gets you going
Sam S
Applications Engineer
National Instruments

New to LV DSP Module,ask about the supported functions

Hi all,
I plan to use LV DSP module, but I am not sure if this module supports legacy LV functions. I looked at its manual, it only mentions DSP module supports many DSP specific functions.
Does it support linear algebra functions like eigenvalue/vector calculation in the target DSP device?
Thanks !
Sunny

Hi Sunny,
No, I don't think some origianl LV functions are still available with DSP targets. Because some mathematical functions are calculation-consuming, their algorithm need to be specially optimized when transformed to DSP targets. Please also notice that the LabVIEW DSP module only supports several targets including the
NI SPEEDY-33, Texas Instruments TMS320C6713 DSK and TMS320C6711 DSK.
Zheng

Speedy-33 Echo Example with DSP Module's Variable Delay Block

Hi,
I was trying to implement the echo effect using the DSP Module's Variable Delay Block, it works fine and I could hear the echo nicely, however, it was restrictred to the maximum delay of 4095 (for frame size of 1, and 4094 for FZ of 2, etc....). This means that the maximum delay I could get is 0.5 second with 8k sampling. May I know what is the reason behind? is it due to the HW buffer or what? and how to workaroud this?
Thanks
CL

Remember that Arch Arm is a different distribution, but we try to bend the rules and provide limited support for them. This may or may not be unique to Arch Arm, so you might try asking on their forums as well.

Integrating a DSP and BlackFin Modules with LV 8.5

Hi all,
I am just posting my last trouble when I was using Labview software for an academic work.
So I'll try to summarize the topic.
So, the point was to integrate LB with DSP board specifically model BF537 from BlackFin.
The problem is: Not all version of Labview can support DSP Module (this is an extension that you should install to do the integration possible) and BlackFin Embedded application for BF537 as well.
Just to clarify: you should have the correct version of LV because after that, you should install DSP Module and then, BlackFin Embedded.
The LV 8.6 supports BlackFin Embedded but doesn't supports DSP Module. The LV 2009 and LV 2011 we have the same issue. You can read the respective guide of these versions just to check it out.
The only version of LV that can support DSP Module and Embedded Module for Blackfin Processors is version 8.5.
The problem would be solved if both Modules(DSP and BlackFin) would are easily available on NI site or other website.
I spent many hours searching with no success. For LV 8.5 the correct DSP Module is 2.5 and I could not find this specific Module on any ws. Regarding Module for Blackfin Processors I have no problem to download it.
I tried to contact NI local support of my country but they have slow answers and any engineer can help me although all have been very attentive by phone.
My solutions was contact USA engineer. The local team is very efficient and some minutes later the DSP Module 2.5 was available to download in this link:
ftp://ftp.ni.com/outgoing
(mario_2.5.zip)
If anyone has problem to download the file, please let me know. I will be so glad to help.

Hello.
Could you send us your VI (v8.5) please? Thanks.
Regards.
Romain D.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
NIDays 2010 : Conférence mondiale de l'instrumentation virtuelle
>>Détails et Inscription<<

Add Exchange 2010 Powershell Modules with Domain Controller

Hi
We are looking for a way to run Exchange PS cmdlets from Windows 2008 R2 DC. How can we load teh Exchange PS modules with any other server
Thanks in advance
LMS

You don't need to - you can open a remote PowerShell session from the DC to the Exchange server and run the Exchange commands remotely. Use the following commands:
$PsS = New-PSSession -ConfigurationName Microsoft.Exchange -ConnectionUri <a href="http:///powershell">http://<serverFQDN>/powershell -Authentication Kerberos
Import-PSSession $PsS -ErrorAction SilentlyContinue

Best practice identifying ERT modules with SAP / IS-Utilities

Hi everybody,
I'm looking for the best practice identifying ERT modules with SAP / IS-Utilities (electricity).
Here's the physical device set up :
The ERT modules are internal to the electricity meter. They're integrated into a multi purpose electronic circuit. So they can't be remove physically as a separate device.
The ERT modules are used to transmit data from the meter to a radio frequency receiver (handheld or drive-by). The main data that is transmitted is the consumption reading. So the receiver stores the ERT module number and the reading value.
They may be one or more ERT modules in a single meter, and each ERT module transmit his own specific consumption reading (energy reading, demand reading, etc...).
Each ERT module has is own manufacturer number.
My issue is :
To find a way to identify in IS-U the ERT module within the meter's register group (or somewhere else???) in order to relate each register to his ERT module number.
The purpose of all this is to create reading orders with the ERT module number following for each register.
This way we can match, using a unique key, each reading order and his corresponding reading value uploaded from the radio frequency receiver (handheld or drive-by).
Thanks for your help and ideas on best practice.

Hi,
1) The system (application) environment of BI (what is integrated in it - e. g. within the portal, there is a storage for unstructured information like documents or virtual rooms for collaboration between departments - and what does it make)
Document management from RSA1 transaction of BI helps to attach any unstructured documents at specific level in BI.
2) How does development in BI works (development environment, coding, debugging, building, deployment and test) and what is used stronger (ABAP or ABAP OO)? Here, I don't mean how to write ABAP or ABAP OO programs, only the infrastructure from development to transport to a target system
BI has got a separate tool and GUI to perform all the Extract, Transform and load related activities. ABAP is part of BI but you don't need much extensive ABAP learning. Basic ABAP is sufficient to write routines and extractors.
3) How is a BI system to configure as default after installation?
May be a BASIS person can help you out here about the configuration but this is not the job of BI person.
4) Good guides (e/books) to learn ABAP and ABAP OO (as far as possible oriented on the practive)
You can search for SAM Series learn ABAP in 24 days book. This book is sufficient to learn the ABAP required for working in BI.
But except ABAP you will have to completly learn the BI system to work efficiently.
Regards,
Durgesh.

Is it possible to make a Frequency Domain Reflectometer using LabView? For waveguide frequency measurement?

Hi everyone
I have a tricky question that I have looking around for the answer but couldn't find it!
I want to know if I can build a Frequency Domain Reflectometer (FDR) to measure frequency return in waveguide. Telecommunication engineers would understand what I mean! It a bit like TDRs but its frequency instead of time.
I would like to build a Frequency Domain Reflectometer using labview application, how can I do that? What sort of code do I need and what equipment do I need to operate with the NI code?
Please give me the chance to thank you all very very much for your help and support and for looking here,
regards
Fezz

Hi Fezz,
I am not familiar with using FDR systems but know there is a good example of producing a TDR in LabVIEW available on the community. This might provide you with a base and a grasp of the architecture you could use to create the functionality.
Time-Domain Reflectometer (TDR) Example
Regarding the equipment you would require to achieve this I strongly recommend contacting your local NI office who will be able to adviser you fully as this will depend upon your desired specification.
Kind Regards,
Aaron. E
Applications Engineer Team Lead
National Instruments
ni.com/support

Using DSP Module to control C6713 DSK

Hi,
I am doing an Automatic Noise Cancellation design, and am using the LabView DSP Module and downloading code to a TI C6713 DSK. I need 1 microphone to measure ambient noise, and a 2nd microphone to measure my desired speech signal.
I would like to use the MIC_IN input for one microphone, and the LINE_IN input for the 2nd microphone. The DSK has a stereo codec, so I would like to have one channel be the audio from 1 mic and the 2nd channel be the audio from the 2nd mic.
First, is it even possible to do this? If so, how do you use LabView to configure the DSK so that each channel represents the audio from 1 mic?
Thanks for any help.

You definitely can target the TI TMS320C6713 DSK with LabVIEW. You can create a DSP project in LabVIEW 8.2.1 that will add all available I/O to the project. You can then use this I/O to bring in your signals to do any LabVIEW analysis available for that target. As for how you the I/O actually works, TI may be the best people to contact for that. Here is a few links where I found some of this information.
http://zone.ni.com/devzone/cda/tut/p/id/3564
http://zone.ni.com/devzone/cda/tut/p/id/3501
http://zone.ni.com/devzone/cda/tut/p/id/3594
http://zone.ni.com/devzone/cda/tut/p/id/5239
Daniel Eaton
National Instruments
Systems Engineering
Embedded and Industrial Control

How to check DSP modules installed status

Dear All,
How will I check up the DSP modules installed status in cisco 7206 router.
How can i know whether those DSP modules are installed with
2 Channelized E1/PRI port(s) or in the chasis itself.
Thanks
Shibu

Dear Nick,
Please find the sh voice DSP.
-HQ#sh voice dsp
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS ABORT PACK COUNT
==== === == ======== ======= ===== ======= === == ========= == ===== ============
C549 010 01 g729r8 4.1.41 busy idle 0 0 1/1:15 30 0 6823409/5935
157

Digital Watermarking on image in frequency domain

I am working on a Project which aims at studying the digital watermarking on image, with both spatial domain and frequency domain.
I have finished the spatial domain but is frustrated with the frequency domain right now. I have no idea on how I can possess the frequency domain of a image. Is there a built-in function which can help us to do so?
Thank you for your help.

Also posted and crossposted:
http://forums.sun.com/thread.jspa?threadID=5433169&messageID=10958328#10958328
http://forums.sun.com/thread.jspa?threadID=5433180&messageID=10958329#10958329
http://forums.sun.com/thread.jspa?threadID=5433412&messageID=10959648#10959648
http://forums.sun.com/thread.jspa?threadID=5433693&messageID=10961065#10961065
http://forums.sun.com/thread.jspa?threadID=5433694&messageID=10961066#10961066

Enhanced frequency domain decomposition for modal analysis

Hi eveyone
I can't find enhanced frequency domain decomposition algorithm for ambiant vibration of modal analysis.(Not frequency domain decomposition).
Also ı can't find to operational modal analysis example with labview.(not experimental).
Can you help me?
Best Regards...
Himmet GENCER
Software Development Coordinator at Teknik Destek Grubu
[email protected]

thanks for answer.Yes I using the sound and vibration toolkit.But Exactly I don't find what ı searched.
ama ben tam olarak ne ı aradı bulmuyorum
Himmet GENCER
Software Development Coordinator at Teknik Destek Grubu
[email protected]

Integrating a frequency domain signal

Hi
I am trying to extract the response of a frequency dependent signal :
1. First, I use the SignalFFT vi to get into the frequency domain.
2. Then I plan to integrate the FFT signal around a certain frequency and take a ratio of that wrt to the integral over the entire frequency spectrum to get a measure of how strong the signal is around that frequency.
I am choosing a range of frequencies above because the physical phenomenon producing the time domain signal produces a certain lifetime width. I need a numerical integration VI that can do step 2 above. The numerical integration VI that I found in Labview (using ver. 7.1) integrates the whole signal, and there is no way to define limits between which the numerical integration should be carried out.
Any ideas ?
Thanks.

That a cool question!
This has to do with the sample rate, when you adquire the signal, you get set of samples, that hava a sample rate, and when you do an FFT on those samples, every sample corresponds to frecuency bin (kinda of frecuency samples). Example:
If you get 100 samples at 1kHz, you will get a 100 windows, this is 100 samples to represent 1kHz, however, only the half of the spectrum is valid, because of the Nyquist teorem, so this mean that from 0 to 49, you have a correct representation, from 50 to 99 you have a reflection of the spectrum. So in the first 50 "frequency samples" you have 0-500Hz
Tania Lozoya

Frequency domain in dsp module with speedy-33 target

Similar Messages

Maybe you are looking for