FTP server with NVG589

Hello, I'm attempting to get an FTP server up and running and I cannot get it to work. I have gone to the NAT/Gaming section and added the FTP rule to my home computer. However when I try to launch the server (I'm using BabyFTP) it says it cannot listen on Port 21. I double checked in NAT/Gaming, and it says it is forwarding port range 20-21.... Did I miss a step somewhere?

If the software says that it cannot listen on port 21, that probably means that something else has already claimed port 21 on the system it is running on, e.g. the Windows FTP service perhaps. This would have nothing to do with the NVG589.
Open a Command windows your your PC, type NETSTAT and press ENTER. Look for something with a Local Address ending in ":21".
Once you have the FTP successfully running, be sure to set the NVG589 to port forward FTP (normally ports 21 and 22 have to be forwarded) to your system hosing the FTP service.

Similar Messages

FTP Server with WEB FTP function

Hi,
which is the best solution for a FTP Server with WEB FTP Service?
kind regards
Piero

No, I am not running this solution at a corporate level; I'm just using this one for home use by maybe a dozen people. At any rate, I looked around for several and this one seemed to work best for me. Here's some others I checked into. I did use PFPFileNavigator before I found AjaXplorer. I went with AjaXplorer because I liked the interface better and it has LDAP support.
PHPfileNavigator
http://pfn.sourceforge.net/
Relay
http://ecosmear.com/relay/
Mollify --- Probably the most "Mac looking" one
http://www.mollify.org/
QuiXplorer
http://quixplorer.sourceforge.net/
eXtplorer
http://extplorer.sourceforge.net/
Rumpus
http://www.maxum.com/Rumpus/HomePage.html
BarracudaDrive Web Server
http://barracudaserver.com/products/BarracudaDrive/
I hope this gives you some ideas. I spent about a week Googling, installing, and testing before settling on AjaXplorer. I tried PHPFileNavigator (but didn't have LDAP support, other than that I liked it), Rumpus (didn't like this as it is commercial, and, uses it's own built-in web server), Relay (not enough features), and Mollify (again, no LDAP support).
Best regards,

Can not connect to Cerberus FTP Server with PASV

I setup a FTP Server and i can connect from the inside fine but from the outside i can not connect in passive mode. I can in regular ftp or ssh.
Here is the log from filezilla
Status:          Resolving address of domain.com
Status:          Connecting to ExternalIP:990...
Status:          Connection established, initializing TLS...
Status:          Verifying certificate...
Status:          TLS/SSL connection established, waiting for welcome message...
Response:          220-220-Welcome to Cerberus FTP Server
Response:          220 220 Created by Cerberus, LLC
Command:          USER test
Response:          331 User test, password please
Command:          PASS ***********
Response:          230 Password Ok, User logged in
Command:          CLNT FileZilla
Response:          200 Command okay
Command:          OPTS UTF8 ON
Response:          220 UTF8 support on
Command:          PBSZ 0
Response:          200 PBSZ=0
Command:          PROT P
Response:          200 PROT P OK, data channel will be secured
Status:          Connected
Status:          Retrieving directory listing...
Command:          PWD
Response:          257 "/" is the current directory
Command:          TYPE I
Response:          200 Type Binary
Command:          PASV
Response:          227 Entering Passive Mode (external IP,195,83)
Command:          MLSD
Error:          Connection timed out
Error:          Failed to retrieve directory listing
Result of the command: "show running-config"
: Saved
ASA Version 8.0(4)
interface Vlan1
nameif inside
security-level 100
ip address 192.168.10.10 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group att
ip address pppoe setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
object-group service RDP tcp
description RDP
port-object eq 3389
object-group service FTP_PASV_Ports tcp
description Passive Ports
port-object range 35000 35999
object-group service FTPS tcp
description FTPS
port-object eq 990
access-list outside_access_in extended permit tcp any any object-group RDP
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit tcp any any eq ftp
access-list outside_access_in extended permit tcp any any eq telnet
access-list outside_access_in extended permit tcp any any eq smtp
access-list outside_access_in extended permit tcp any any eq www
access-list outside_access_in extended permit tcp any any eq pop3
access-list outside_access_in extended permit tcp any any eq https
access-list outside_access_in remark passive FTP port range
access-list outside_access_in extended permit tcp any host server object-group FTP_PASV_Ports
access-list outside_access_in extended permit tcp any any eq ssh
access-list outside_access_in extended permit tcp any any object-group FTPS
access-list outside_access_in extended permit tcp any any eq ftp-data
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1492
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface www server www netmask 255.255.255.255
static (inside,outside) tcp interface https server https netmask 255.255.255.255
static (inside,outside) tcp interface smtp server smtp netmask 255.255.255.255
static (inside,outside) tcp interface 3389 server 3389 netmask 255.255.255.255
static (inside,outside) tcp interface pop3 server pop3 netmask 255.255.255.255
static (inside,outside) tcp interface ftp server ftp netmask 255.255.255.255
static (inside,outside) tcp interface ssh server ssh netmask 255.255.255.255
static (inside,outside) tcp interface 990 server 990 netmask 255.255.255.255
static (inside,outside) tcp interface ftp-data server ftp-data netmask 255.255.255.255
access-group outside_access_in in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.10.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh 192.168.10.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
vpdn group att request dialout pppoe
vpdn group att localname @static.sbcglobal.net
vpdn group att ppp authentication pap
vpdn username @static.sbcglobal.net password *********
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
username admin password rcuFiQnIXLd encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:ecb5356a2f5e680b
: end
I am programing the router with ASDM so if you could tell me what i need to do from the GUI to fix this.

Dan,
Looking at the output,
Status:          Resolving address of domain.com
Status:          Connecting to ExternalIP:990...
Status:          Connection established, initializing TLS...
Status:          Verifying certificate...
Status:          TLS/SSL connection established, waiting for welcome message...
This looks like FTPS which is not supported on the ASA. You can workaround it by trying to connect using Active mode from the outside instead of PSV.
You can find more info here:
https://supportforums.cisco.com/docs/DOC-23206
Mike

Picking files from FTP server with dynamic Filename.

Hello Experts,
I want to pick some files from a FTP server in a File to Idoc scenario. The files in the Ftp Server are created with the filenames as timestamp of the file when it was created. How do I pick up these files?
Thanks,
Merrilly

Hi,
The above masking concept (*.txt, . etc) will be applicable for the files with NFS only,
See the below link to apply it
/people/mickael.huchet/blog/2006/09/18/xipi-how-to-exclude-files-in-a-sender-file-adapter
The below link will help you to build up the adapter module to read the dynamic file name
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/da5675d1-0301-0010-9584-f6cb18c04805
This could be applicable for FTP ...
Thanks
Swarup

How to connect to FTP server with out hardcoding the Password?

HI experts,
IN my SAP R3 i neeed to send a small file to FTP server from SAP application server using abap program.
I found out many FMS which can connect ot FTP , but password need to be stored in Program.
As per security issues i am not allowed to hardcode or keep the Password as constant , as my clinet will change the password weekly.
Please suggest me a solution. How can we give the Password dynamically to the system.

hi sivaram,
You can keep the id password in a Batchfile and create a external command which doesnot need anyput just call external command from program and transfer file.

How do I automatically upload files to an FTP server with Compressor 4?

So I've been using Compressor 4 in order to compress some videos into a manageable size for streaming. However, I've been trying to figure out how to set up an automatic FTP upload to the program Transmit through Compressor 4, but have been running into roadblocks. When choosing a destination by using the plus icon in the destinations tab, the choice of local or remote no longer appears. Also, when going to the actions tab in the Inspector box, the option to "Execute Applescript" is also gone.
Has anyone found a way around this yet? I have no experience with Automator, so I am hesitatnt in spending the time to learn a new program just to make the process of compressing and uploading more efficient.

Hi Nick.
I'm afraid it went missing in the 4.0.3 update for whatever reason. Unless you have a way of rolling C back one version, you'll either have to write a work-around or see whether it re-appears in a future version.
Also, http://www.apple.com/feedback/compressor.html
Russ

Setup automated Powershell to upload files to a remote ftp server with ssl

Thanks in advance for the advice!
I need to create a script to upload a file to a remote server to transfer some large files, and I've been reviewing some methods needed, and have a few questions.
Is there a best practice for sending large files?
Is the webrequest or put commands better to use?
This will be the first time we use Powershell on this server. Should I change the executive policy on the server or should I change it in the script when running for security purposes? This is a data warehouse therefore our strategic
data is else where but want to make sure everything is secure as possible.
I am able to run something similar on my laptop which works but when I try it on the server it is blocked. I'm assuming I'll have to open up port 22 for this application to work. How can I confirm that this is the port Powershell
needs open for these transfers.
Any references to learning links appreciated since I'm new to Powershell.
Thanks!

Sorry but we cannot help you with this. We suggest you contact a support tech or consultant to help you set up your system.
Start by learning how PowerShell works and how to set it up. As fro the SSL you will need to postyourscript with any issues and errors.
Start here:
http://technet.microsoft.com/en-us/scriptcenter/dd793612.aspx
¯\_(ツ)_/¯

Java ftp server which can use LDAP, how to integrate with WLS' implementation of LDAP?

Howdy.
I'm setting up a java ftp server
(http://www.mycgiserver.com/~ranab/ftp/index.html) which is capable of using
LDAP for it's user security. I would like to integrate this ftp server with
wls' implementation of LDAP so I only have to admin one user list.
Does wls put it's user list in the LDAP or in it's own proprietary setup? I
tried playing around with it, but the users don't seem to appear in the JNDI
tree. Is this where the LDAP stuff is located? I thought it was in there?
If it's in it's own setup, is there a way to propagate the users to LDAP?
If these look like newbie Q&A, I guess they kind of are, I'm new to LDAP.
Thanks for any input you might have.

Peter,
If you are talking about using the embedded LDAP server in WLS 7.0 for this purpose
I think you are going done the wrong path.
Look at the following URL on how to use an external LDAP server for your custom
application
http://e-docs.bea.com/wls/docs70/secmanage/realm.html#1172008
Chuck Nelson
DRE
BEA Technical Support

Retrieve text file from ftp server every 15 mins

Hi guys,
We are able to connect to an FTP server with 5 text files. Every 15 minutes, we need to retrieve each of the 5 files. Please assist me with the coding logic to retrieve the file into the SAP Directory. Any suggestions would be greatly appreciated.
Regards,
Sid

Sid
Try searching on SCN, there are plenty of materials you can find without even asking a question in the forum.
How to use SCN search
For example, if you search with keywords "FTP ABAP", immediately the first two Wiki entries would give you the details you are looking for.
Rgds
Eng Swee

Getting file from ftp server problem.

Anyone can tell me what's wrong with my code.
I try to get Test.txt from my ftp server with this coding :
public class FTPClient{
public static final void main(String[] args) throws Exception
{ try {
URL url = new URL("ftp://user:password@myhost:21/MyFiles/Test.txt");
URLConnection c = url.openConnection();
BufferedReader r = new BufferedReader(new InputStreamReader(c.getInputStream()));
String l = null;
while ( (l = r.readLine()) != null)
System.out.println(l);
catch (Exception e)
System.out.println("Uh oh, got an IOException error!");
e.printStackTrace();
But i get the following error :
sun.net.ftp.FtpProtocolException: PORT :
at sun.net.ftp.FtpClient.openDataConnection(FtpClient.java:435)
at sun.net.ftp.FtpClient.get(FtpClient.java:550)
at sun.net.www.protocol.ftp.FtpURLConnection.getInputStream(FtpURLConnection.java:382)
at FTPClient.main(FTPClient.java:8)
Can somebody help me,
What's worng with my coding..?
Thanks,

I delete the :21 from my code but the same error occured.
I also try this code
FtpClient ftpClient = new FtpClient();
String host ="10.10.10.237";
String username="username";
String password="password";
try
ftpClient.openServer(host); // connect to FTP server
ftpClient.login(username, password); // login
ftpClient.cd("TestFTP");
ftpClient.binary();
InputStream is = ftpClient.get("Test.txt");
ftpClient.closeServer(); //close connectionand I got the same error
sun.net.ftp.FtpProtocolException: PORT :
at sun.net.ftp.FtpClient.openDataConnection(FtpClient.java:435)
at sun.net.ftp.FtpClient.get(FtpClient.java:550)
at Client.main(Client.java:19)
I dont know what is the problem.. I've try to find information about this error on the net, but cannot find anything that can help me...

I'm new to Solaris 10 and need help to setup ftp server

hello!
I just installed Solaris 10 and I'm trying to setup an ftp server (with ftpd) but I don't know how to do that
my server doesn't need any security or authentication
I'm looking for the default shared files directory
Also wondering what to change in what configuration file...
This OS looks quite similar to some linux I used before but the differencies are big enough to drive me crazy
anyway thanks for your help.
Any advice is welcome :-)

cd /etc/ftpd
vi ftpusers
put a # in front of root and any other users that you wish to be able to ftp
then svcadm restart ftp
If you want to set up an anonymous ftp server, there is a little more involvement

How to read a ftp file with a specified file name in Proxy-XI-File scenario

Dear all,
I have the following requirement:
The end user send a request via the proxy to XI, within the request parameters there is a file name, and the XI need to retrieve the file content from a ftp server with this specified file name, how can I achieve this?
According to my understanding, the file receiver adapter can only write the files to the server.
Thanks and regards,
Bean

Dear Bean,
This can be achieved using a BPM...
you will have to use Two parallel receive steps within a fork...
1. 1st receive step :This will bring the data from the proxy
2. 2nd receive step :according to pipeline step before this step would be executed interface determination would be called withini that you can put a mapping wherin the source and target message type would be as follows
a. source message type ; the file structure that is going to be picked from ftp structure
b.target message type : same structure as source except at top you will add "filename" field
(you cna find on forum how we can get a fielname in the mapping ..in case you dont knw )
3. now you can define correlation on the field "fielname" in both the receive steps provide the hirearchy and structure of data coming from both file and procy are same...
4.. after corelation you can put any steps like transformation ( as you want)
Hope this helps

How to output FTP file with Code Page 8400?

Hi gurus,
       As we know we can use GUI_DOWNLOAD to download fiel with specific Code Page,
CALL METHOD cl_gui_frontend_services=>gui_download
    EXPORTING
     filename          = 'E:\TEXT.TXT'
*      confirm_overwrite = 'X'
      codepage          = '8400' "Chinese
    CHANGING
      data_tab          = i_file
    EXCEPTIONS
     file_write_error = 1
      OTHERS            = 24.
IF sy-subrc EQ 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
               WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
But my question is how to output file into FTP server with specific code page 8400?
call function 'FTP_R3_TO_SERVER'
    exporting
      handle         = p_handle
      fname          = p_filename
      character_mode = 'X'
    tables
      text           = i_file
    exceptions
      tcpip_error    = 1
      command_error = 2
      data_error     = 3
      others         = 4.

Thanks but it is not my anwser
I want to output file to FTP Server with specific code page like
GUI_DOWNLOAD

FTP Server in SAP XI

Hi Friends,
1. i have a question in XI. i want intergrate Mainframe systems and Siebel system through XI by using File to File Scenario.
here XI will pick the file from Sender FTP server with File adapter, processing the file and send to Receiver FTP server with File adapter.
Here my doubt is, FTP servers are different systems or both are same? And these servers are not part of the XI server right?
here i am confusing so much, i am thinking both sender & receiver maintaining their own FTP servers.
2. what is soap end point.
3. how many elements are there in a sender data type for JDBC to File Scenario.
please respond regarding the above quickly.
i am very thankful to you all in advance.
Regards,
Nagarjuna.

Hi,
1. i have a question in XI. i want intergrate Mainframe systems and Siebel system through XI by using File to File Scenario.
here XI will pick the file from Sender FTP server with File adapter, processing the file and send to Receiver FTP server with File adapter.
Here my doubt is, FTP servers are different systems or both are same? And these servers are not part of the XI server right?
here i am confusing so much, i am thinking both sender & receiver maintaining their own FTP servers.
FTP protocol is generally used for communication with external servers, it is not part of XI, it is operating sytem level protocol. We need to active FTP server at operating system level
2. what is soap end point.
For SOAP interface we need to create web service, it is part of XI, through WSDL we can create web service
3. how many elements are there in a sender data type for JDBC to File Scenario.
If sender is JDBC we need to create SQL query in XML format, after that message type, interface type and Mesage Mapping & interface mapping need to configure. Meanwhile receiver structure*
please respond regarding the above quickly.
i am very thankful to you all in advance.

FTP Issue with Host name

Hi All,
When i tried to send the file to other FTP server with host name i am getting below error.
Error when getting an FTP connection from connection pool: com.sap.aii.af.lib.util.concurrent.ResourcePoolException: Unable to create new pooled
resource: UnknownHostException: ftp.kms.telnet.vector.com.
But i am able to send the file successfully using IP address.
Can anyone pls suggest if any additional settings needs to be done in file adapter.
Or any other setting needs to be taken care.
Please advise.
Thannks,
Swetha

Hi,
Basis people are not aware of adding in host file, for that reason i am asking input here.
My XI ssytem runs on OS level i.e on AS400.
Basis team tried to reach host file by mapping into server, but they are unable to find host file. Do i need to ask OS level expert to add entry in host file.
For my knowledge, can you pleae give me the path of host file at OS level if you have any idea.
Please advise
Thanks,
Swetha

FTP server with NVG589

Similar Messages

Maybe you are looking for