Getting Error Logs Every Minit's From 5k

Hi,
Am getting every minit's this below logs.........
Can i know why it's happening....
Please advice me....
Logs:
=====
2012 Sep 3 17:17:42 5k %ETHPORT-5-IF_UP: Interface Ethernet106/1/3 is up in mode access
2012 Sep 3 17:17:55 5k %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet106/1/2 is down (Link failure)
2012 Sep 3 17:17:56 5k %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet106/1/3 is down (Link failure)
2012 Sep 3 17:17:58 5k %ETHPORT-5-SPEED: Interface Ethernet106/1/2, operational speed changed to 1 Gbps
2012 Sep 3 17:17:58 5k %ETHPORT-5-IF_DUPLEX: Interface Ethernet106/1/2, operational duplex mode changed to Full
2012 Sep 3 17:17:58 5k %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet106/1/2, operational Receive Flow Contr
ol state changed to off
2012 Sep 3 17:17:58 5k %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet106/1/2, operational Transmit Flow Cont
rol state changed to on
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_UP: Interface Ethernet106/1/2 is up in mode access
2012 Sep 3 17:17:59 5k %ETHPORT-5-SPEED: Interface Ethernet106/1/3, operational speed changed to 1 Gbps
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_DUPLEX: Interface Ethernet106/1/3, operational duplex mode changed to Full
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet106/1/3, operational Receive Flow Contr
ol state changed to off
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet106/1/3, operational Transmit Flow Cont
rol state changed to on
2012 Sep 3 17:17:59 5k %ETHPORT-5-IF_UP: Interface Ethernet106/1/3 is up in mode access
NX5K005#
=====================================================
NX5K005# sh running-config | b Ethernet106/1/2
interface Ethernet106/1/2
interface Ethernet106/1/3
interface Ethernet106/1/4
description MSSQL01
switchport access vlan 3838
spanning-tree port type edge
interface Ethernet106/1/5
description BCKUP01
switchport access vlan 3200
spanning-tree port type edge
=======================================================
show vpc brief
vPC Peer-link status
id   Port   Status Active vlans
1    Po130 up     1,700-701,798,920-923,1100-1103,1105-1108,1110-111
                   3,1115-1118,1120-1123,1125-1128,1130-1133,1135-113
                   8,1140,1145,1150,1155,1160,1165,1300-1303,1305-130
                   8,1310-1313,1315-1318,1320-1323,1325-1328,1330-133
                   3,1335-1338,1340,1345,1350,1355,1360,1365,1500-150   ....
vPC status
id     Port        Status Consistency Reason                     Active vlans
13     Po13        up     success     success                    1,700-701,7
                                                                 98,920-923,
                                                                 1100-1103,1
                                                                 105-1108,11
                                                                 10-1113....
105    Po105       up     success     success                    -
106    Po106       up     success     success                    -
106496 Eth105/1/1 up     success     success                    3830
106497 Eth105/1/2 up     success     success                    1
106498 Eth105/1/3 up     success     success                    1
106499 Eth105/1/4 up     success     success                    3838
107520 Eth106/1/1 up     success     success                    3830
107521 Eth106/1/2 up     success     success                    1
107522 Eth106/1/3 up     success     success                    1
107523 Eth106/1/4 up     success     success                    3838

Thanks i will check and let you know....
The one more switch also am getting Error Logs please check and let me know this link fluctuating when i see the "Shoe VPC" some time showing link down please see below logs.
advice me ASAP.
Error Logs:
===========
2012 Sep 4 10:22:42 NX5K %ETHPORT-5-IF_UP: Interface Ethernet107/1/2 is up in mode access
2012 Sep 4 10:23:52 NX5K %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet107/1/2 is down (Link failure)
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-SPEED: Interface Ethernet107/1/2, operational speed changed to 1 Gbps
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_DUPLEX: Interface Ethernet107/1/2, operational duplex mode changed to Full
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Receive Flow Contro
l state changed to off
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Transmit Flow Contr
ol state changed to on
2012 Sep 4 10:23:55 NX5K %ETHPORT-5-IF_UP: Interface Ethernet107/1/2 is up in mode access
2012 Sep 4 10:24:09 NX5K %ETHPORT-5-IF_DOWN_LINK_FAILURE: Interface Ethernet107/1/2 is down (Link failure)
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-SPEED: Interface Ethernet107/1/2, operational speed changed to 1 Gbps
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-IF_DUPLEX: Interface Ethernet107/1/2, operational duplex mode changed to Full
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-IF_RX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Receive Flow Contro
l state changed to off
2012 Sep 4 10:24:12 NX5K %ETHPORT-5-IF_TX_FLOW_CONTROL: Interface Ethernet107/1/2, operational Transmit Flow Contr
ol state changed to on
2012 Sep 4 10:24:13 NX5K %ETHPORT-5-IF_UP: Interface Ethernet107/1/2 is up in m
Show VPC:
===========
108544 Eth107/1/1 up     success     success                    3830
108545 Eth107/1/2 down* failed      Consistency Check Not      -
                                      Performed
108546 Eth107/1/3 up     success     success                    1
108547 Eth107/1/4 up     success     success                    3838
Within One Minit same link fluctuating:
=======================================
Show VPC:
========
108544 Eth107/1/1 up     success     success                    3830
108545 Eth107/1/2 up     success     success                    1
108546 Eth107/1/3 up     success     success                    1
108547 Eth107/1/4 up     success     success                    3838
Regards,
Senthil

Similar Messages

TS1286 getting error 9 every time try to restore iphone 5 crash on me tell me to go to itunes did it on a pc got error -1 so had a go on my mini mac get error 9 all the time

im update firmware for iphone 5 to 6.1.4 getting error 9 every time try to restore iphone 5 crash on me tell me to go to itunes did it on a pc got error -1 so had a go on my mini mac get error 9 all the time

This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if the device is manually disconnected during the restore process. This issue can be resolved by performing USB troubleshooting, using a different USB dock-connector cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.

From where we can get error log of delivering state

Hi Experts,
I have processed large file and itseems the message got picked up successfully from sender side and got stucked in deleivering state. Can anyone suggest from where can we get error log that why the message is in delivering state.
I have checked in channel and MM log but nat able to find.
Thanks,
Swetha

Hi,
You can check in engine status - backlog data in adapter engine in component monitoring.
Please check below link:
[http://help.sap.com/saphelp_nwpi71/helpdata/en/12/5dd23aaad7b3408dde3c1577fda5b3/content.htm]
Regards,
Beena.

HT1386 I keep getting error 4001 every time i try to put music from old ipod to iphone

I keep getting error 4001 every time I try to put music from old ipod to new iphone.....what do I do ?

The iTunes Match servers may be busy; see discussion here: https://discussions.apple.com/message/18525437#18525437%2318525437.

Im getting error 14 every time i try to restore my ipod touch,any fixs?

im getting error 14 every time i try to restore my ipod touch? anyone know how to fix this?
i have itunes 9 and this problem started when i bought the new itouch software. i have alreay tried deleting itunes then re-installing it.

Well, the problem isn't the back up because I already have a backup saved that I can restore from, I honestly don't know how, but I do, and it has all my apps. The problem is restoring it. I keep getting the "There was a problem downloading the software for the iPod "King". A duplicate file name was specified. With my 3G iPod touch, I did not have it named as "King". I had it as another name. I don't know if that helps, but as I said before, Backup-wise I'm okay for now. Restore-wise I'm not.
NOTE: Reinstalling iTunes doesn't help.

Im getting error 14 every time i try to restore my ipod touch?

im getting error 14 every time i try to restore my ipod touch? anyone know how to fix this?
i have itunes 9 and this problem started when i bought the new itouch software. i have alreay tried deleting itunes then re-installing it.

Well, the problem isn't the back up because I already have a backup saved that I can restore from, I honestly don't know how, but I do, and it has all my apps. The problem is restoring it. I keep getting the "There was a problem downloading the software for the iPod "King". A duplicate file name was specified. With my 3G iPod touch, I did not have it named as "King". I had it as another name. I don't know if that helps, but as I said before, Backup-wise I'm okay for now. Restore-wise I'm not.
NOTE: Reinstalling iTunes doesn't help.

I am unable to get my Ipod touch 4g to upgrade to ios 5 I keep getting error messages every attempt?

I am unable to get my Ipod touch 4g to upgrade to ios 5 I keep getting error messages every attempt!
any ideas on how to fix this?

mine iphone4. same. Apple admin, answer to fix it?

Jrun errors logged every minute in CF8

Hi. We've had errors logged every few minutes for several years and would like to know how to stop them please? The log path and a file name example is:
<drive>\JRun4\lib\wsconfig\1\LogFiles\jrun_iis6_wildcard130603.log
The first few lines of the latest log are below.
2013-06-03 07:59:09 jrISAPI[init:2060] JRun ISAPI Extension DLL Detaching (FreeLibrary)
2013-06-03 08:19:15 jrISAPI[init:3816] JRun 4.0 (Build 108673) JRun ISAPI Extension - Mar 13 2008 19:48:36
2013-06-03 08:19:15 jrISAPI[init:3816] JRun ISAPI Extension DLL Attaching
2013-06-03 08:19:30 jrISAPI[5648:3816] 127.0.0.1:51020 connect failed[740]: 10060 Connection timed out
2013-06-03 08:19:30 jrISAPI[5648:3816] Couldn't initialize from remote server, JRun server(s) probably down.
2013-06-03 08:20:49 jrISAPI[3712:3816] 127.0.0.1:51020 connect failed[644]: 10060 Connection timed out
2013-06-03 08:20:49 jrISAPI[3712:3816] Couldn't initialize from remote server, JRun server(s) probably down.
2013-06-03 08:21:21 jrISAPI[1824:3816] 127.0.0.1:51020 connect failed[804]: 10060 Connection timed out
2013-06-03 08:21:21 jrISAPI[1824:3816] Couldn't initialize from remote server, JRun server(s) probably down.
The last 2 lines are repeated every minute.
We stopped the built-in Jrun web server after installation years ago as it's an uncessary component in production. I don't understand why something is still requesting data from the Jrun server every minute.
Setup: CF 8.01 x64 installed as multi-server instance on Windows 2008 R2 with IIS7.5.
Thanks in advance for any solutions or suggestions.
Gary F

Delete and re-add the web server connector?
Adam

Getting error message on ungrade install from itunes 10 to itunes 11

getting error message on ungrade install from itunes 10 to itunes 11

What does the error message say? (Precise text, please.)

TS3694 Keep getting error 3004, every peice of information on this webstie about the error code is absolutly useless.

Keep getting error 3004, every peice of information on this webstie about the error code is absolutly useless.

Have you tried on another computer connected to a different network?

HT4623 I still can't update, i get error 3252 every time, after over 500mb is downloaded, not happy to waste all the data i could use for other things

I still can't update, i get error 3252 every time, after over 500mb is downloaded, not happy to waste all the data i could use for other things.
is there another way i can download the update? it just never work, tried multiple time

The most common causes are:
Your antivirus, firewall or router security is blocking access to Apple's servers - try temporarily disabling them - if you have Kaspersky this is definitely the problem
At some time in the past you used this computer to jailbreak, unlock or otherwise hack ANY iPhone, iPod Touch or iPad - if this applies to you your hosts file is corrupt and you will have to edit it and remove any lines that contain "gs.apple.com"

Getting error in consuming google webservices from JspDynPage

Hi All,
Getting following error while consuming google webservices from JspDynPage
An exception occurred while processing a request for :
iView : GoogleSer.google
Component Name : GoogleSer.google
Could not find portal application com.company.global.enterprise.portal.wsdl.webservices.service.
Code :
MyGoogle googleService =
(MyGoogle) PortalRuntime.getRuntimeResources().getService("com.company.global.enterprise.portal.wsdl.webservices.service.MyGoogle");
GoogleSearchResult result = googleService.doGoogleSearch("google", "SAP", 0, 10, false, "", false, "", "", "");
ResultElement[] results = result.getResultElements();
if(results != null) {
response.write("<br> Search Result Size " +results.length );
for (int i = 0; i < results.length; i++) {
response.write((i + 1) + ": " + results);
Thanks
Rudra

Hi,
I am still having the same problem, however the scenario in which I am getting varies.
I am getting this exception:
"com.sap.engine.services.webservices.jaxm.soap.accessor.NestedSOAPException: IOError while working with the message."
Some users when trying to login into the portal are getting blank screen and for some the portal launcher page is loading fine and could go to the Home Page.
When I view the logs I am seeing the Nested Soap Exception.
Any Ideas??? Starting the J2EE engine also did'nt help.
Thanks in advance.
Madhavi

What may cause Errors.log to be generated from Essentials configuration wizard?

I customized install.wim to handle specific drivers, and while the OS installs properly... during the Essentials Configuration Wizard, the process nearly immediately stops at 0% and generates this file "Errors.log" with the contents:
FATAL: SetFolderPermission:
Is it just a corrupted install.wim, that just so happens to prevent the wizard from working... or did I accidently change permissions on something that would lead to this type of error?

Well you finally lost me :) Any data partitions are pretty much irrelevant until after Essentials is done installing
Essentials does not get it "installed", Windows gets Installed, and then Essentials "Configures". As I said part of this configure is to decide where the largest data partition is. The team does not do tons of what if's in
the Dev cycle. I have no clue what that code/logic actually is, but I am certain it went no deeper than a normal standard Server install. They did not test different allocation units, smaller than standard "hidden partitions with drive letters.
This said, I was able to complete the Essentials configuration using my unattend.xml with 100, 350, and 328. I used diskpart to assign letters to the 100 and 350, and formatted a 70 gb "data" partition with the 64k and gave it B: But I am
confused as after Essentials config finished the 100 and 350 did not have drive letters? Also when I assign the letters it was not reflected in diskmgmt.msc. Right click still only showed Help. But File Explorer did.
So my ask would be that you edit your winpe to, 100, 350, and 328, and format the system drive with 4k and see if that works for you. Then we/you could change things one at a time to see what breaks it.
All this said, even if we can figure out what breaks it and I file a bug they may acknowledge it is a bug but will mark it as will not fix in this build, and the next build. If we can explain to the Dev team why it should work this way, that this is
the future of Server installs they may look at changing it in V.next.next t be shipped, who knows when. 3 years from now?
Grey

Getting error while opening Excel document from SharePoint site

Hello All,
I am getting following error while opening Excel document from SharePoint site.
This issue appears when we open Excel document from Windows>> Run using below mentioned command:
Excel.exe "{File Name}"
If once I go to Excel back stage and browse for the SharePoint location, then this problem disappears.
I have a work around for this issue but main problem is that i do not have any work around when i need to open Exel document using Excel COM interop in C#.
Thanks,
Amit Bansal
Amit Bansal http://www.oops4you.blogspot.com/

Hi Amit Bansal,
Thanks for posting in MSDN forum.
This forum is for developers discussing developing issues involve Excel application.
According to the description, you got an error when you open the document form SharePoint site.
Based on my understanding, this issue maybe relative to the SharePoint, I would like move it to
SharePoint 2013 - General Discussions and Questions forum.
The reason why we recommend posting appropriately is you will get the most qualified pool of respondents, and other partners who read the forums regularly can either share their knowledge or learn from your interaction with us.
Thanks for your understanding.
Regards & Fei
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Getting error while hitting weblogic server from EBS client instance

Hi,
We are trying to hit weblogic server from EBS client instance.
Steps Done from our side :-
1. Created a self signed key store and certificate (.cer file) with server host name and used it for SSL enabling on weblogic server.
2. Created a self signed key store and certificate (.cer file) with client host name and used it for SSL enabling on oracle EBS client.
3. Imported client certificate .cer file in Server Side Trust Store.
4. Used Server keystore for client side verification.
We are getting these logs from Client Side (Oracle EBS AS) :-
<Nov 9, 2012 10:40:33 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=Entrust Root Certification Authority - G2,OU=(c) 2009 Entrust\, Inc. - for authorized use only,OU=See www.entrust.net/legal-terms,O=Entrust\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:33 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=thawte Primary Root CA - G3,OU=(c) 2008 thawte\, Inc. - For authorized use only,OU=Certification Services Division,O=thawte\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:33 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:33 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:33 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GlobalSign,O=GlobalSign,OU=GlobalSign Root CA - R3". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:33 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "OU=Security Communication RootCA2,O=SECOM Trust Systems CO.\,LTD.,C=JP". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:33 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=VeriSign Universal Root Certification Authority,OU=(c) 2008 VeriSign\, Inc. - For authorized use only,OU=VeriSign Trust Network,O=VeriSign\, Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:34 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:34 AM AST> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=GeoTrust Primary Certification Authority - G3,OU=(c) 2008 GeoTrust Inc. - For authorized use only,O=GeoTrust Inc.,C=US". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
<Nov 9, 2012 10:40:34 AM AST> <Warning> <Security> <BEA-090542> <Certificate chain received from whjed-ebspay.nmc.com - 192.168.100.169 was not trusted causing SSL handshake failure. Check the certificate chain to determine if it should be trusted or not. If it should be trusted, then update the client trusted CA configuration to trust the CA certificate that signed the peer certificate chain. If you are connecting to a WLS server that is using demo certificates (the default WLS server behavior), and you want this client to trust demo certificates, then specify -Dweblogic.security.TrustKeyStore=DemoTrust on the command line for this client.>
<Nov 9, 2012 10:40:34 AM AST> <Warning> <Security> <BEA-090542> <Certificate chain received from whjed-ebspay.nmc.com - 192.168.100.169 was not trusted causing SSL handshake failure. Check the certificate chain to determine if it should be trusted or not. If it should be trusted, then update the client trusted CA configuration to trust the CA certificate that signed the peer certificate chain. If you are connecting to a WLS server that is using demo certificates (the default WLS server behavior), and you want this client to trust demo certificates, then specify -Dweblogic.security.TrustKeyStore=DemoTrust on the command line for this client.>
<Nov 9, 2012 10:40:34 AM AST> <Warning> <Security> <BEA-090542> <Certificate chain received from whjed-ebspay.nmc.com - 192.168.100.169 was not trusted causing SSL handshake failure. Check the certificate chain to determine if it should be trusted or not. If it should be trusted, then update the client trusted CA configuration to trust the CA certificate that signed the peer certificate chain. If you are connecting to a WLS server that is using demo certificates (the default WLS server behavior), and you want this client to trust demo certificates, then specify -Dweblogic.security.TrustKeyStore=DemoTrust on the command line for this client.>
javax.net.ssl.SSLKeyException: [Security:090542]Certificate chain received from whjed-ebspay.nmc.com - 192.168.100.169 was not trusted causing SSL handshake failure. Check the certificate chain to determine if it should be trusted or not. If it should be trusted, then update the client trusted CA configuration to trust the CA certificate that signed the peer certificate chain. If you are connecting to a WLS server that is using demo certificates (the default WLS server behavior), and you want this client to trust demo certificates, then specify -Dweblogic.security.TrustKeyStore=DemoTrust on the command line for this client.
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.fireException(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.fireAlertSent(Unknown Source)
at com.certicom.tls.record.handshake.HandshakeHandler.fireAlert(Unknown Source)
at com.certicom.tls.record.handshake.HandshakeHandler.fireAlert(Unknown Source)
at com.certicom.tls.record.handshake.ClientStateReceivedServerHello.handle(Unknown Source)
at com.certicom.tls.record.handshake.HandshakeHandler.handleHandshakeMessage(Unknown Source)
at com.certicom.tls.record.handshake.HandshakeHandler.handleHandshakeMessages(Unknown Source)
at com.certicom.tls.record.MessageInterpreter.interpretContent(Unknown Source)
at com.certicom.tls.record.MessageInterpreter.decryptMessage(Unknown Source)
at com.certicom.tls.record.ReadHandler.processRecord(Unknown Source)
at com.certicom.tls.record.ReadHandler.readRecord(Unknown Source)
at com.certicom.tls.record.ReadHandler.readUntilHandshakeComplete(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.completeHandshake(Unknown Source)
at com.certicom.tls.record.WriteHandler.write(Unknown Source)
at com.certicom.io.OutputSSLIOStreamWrapper.write(Unknown Source)
at java.io.BufferedOutputStream.flushBuffer(BufferedOutputStream.java:65)
at java.io.BufferedOutputStream.flush(BufferedOutputStream.java:123)
at java.io.FilterOutputStream.flush(FilterOutputStream.java:123)
at weblogic.net.http.HttpURLConnection.writeRequests(HttpURLConnection.java:158)
at weblogic.net.http.HttpURLConnection.getInputStream(HttpURLConnection.java:363)
at oracle.apps.nmc.filetransmission.DigitalSigner.sendSignedFileToBank(DigitalSigner.java:532)
at oracle.apps.nmc.filetransmission.DigitalSigner.signXmlFile(DigitalSigner.java:330)
at oracle.apps.nmc.filetransmission.DigitalSigner.invokerInit(DigitalSigner.java:437)
at oracle.apps.nmc.filetransmission.DigitalSigner.runProgram(DigitalSigner.java:390)
at oracle.apps.fnd.cp.request.Run.main(Run.java:157)
We are getting these logs from Server Side (Weblogic server) :-
<Nov 9, 2012 10:34:51 AM AST> <Warning> <Security> <BEA-090482> <BAD_CERTIFICATE alert was received from whjed-apstest3.nmc.com - 192.168.100.246. Check the peer to determine why it rejected the certificate chain (trusted CA configuration, hostname verification). SSL debug tracing may be required to determine the exact reason the certificate was rejected.>
Kindly suggest on this.
Regards
Deepak Gupta

Hi;
Please make a search BEA-090482 Check the peer to determine why it rejected at metalink. There are 8 docs avaliable, please review them
Regard
Helios

Getting Error Logs Every Minit's From 5k

Similar Messages

Maybe you are looking for