Getting Zen Xtra to work with new compu

I just bought a new Dell 8400 with a Sound Blaster Audigy card. The computer has Creative Media Source version 2.03.29 installed. I plugged my Zen Xtra into the USB port, and I guesss I just expected it to work (but obviously it doesn't). how do I get the new computer to recognize my mp3 player. I can't locate any of the discs that came with the mp3 player. Are there drivers I can download? I looked through the download section, but I really wasn't sure what I was looking for. Any help would be appreciated. Thanks.

For the Zen Xtra right?
I went to and chose MP3 Players > Zen (Hard Disk Dri've/MicroDri've) > Zen Xtra, then Get Files.
The driver was listed there, but you want to download:
Jukebox Driver version .26.02</LI>
Creative MediaSource Software Update version 2.03.29</LI>
NOMAD JukeBox Type 2 Version .0.03 (English) Web Release</LI>
Creative NOMAD Explorer (Version 3.0.0) (if you want to use Nomad Explorer)</LI>
You then want to:
install the driver</LI>
turn the Xtra on and connect to the PC and let the driver install (should be automatic)</LI>
with the Zen still connected to the PC install MediaSource (it needs a Creative product present to validate the install)</LI>
install the Nomad Jukebox Type 2 version (this is required to get MediaSoruce to work with the player)</LI>
If you want, install Nomad Explorer</LI>
That's all you should need to do.

Similar Messages

Nomad Jukebox Zen Xtra stops working with XP following Windows Media Player 11 Beta Installat

Yesterday I was very pleased to find that my Creative Zen Xtra (model DAP-HD00) portable media player is a PlaysForSure capable device. Creative Labs, on November 9, 2005, released the Creative Zen Xtra PlaysForSure Firmware v2.0.03. I installed this firmware (I had to install the Creative ZenJukebox Driver v.30.03 first to get Windows to recognize the device). Once the firmware was upgraded, Windows began recognizing the Zen Xtra as a MTP device and life was good. I was able to synchronize it with both Napster To Go and Windows Media Player 0.
After this, I went ahead and installed Windows Media Player Beta, which I just downloaded yesterday as well.
From a functional standpoint, WMP seems to run just fine. However, when I connected the Creative Zen Xtra (with its PlaysForSure firmware), Windows redetected the hardware. It first showed "Creative Jukebox Zen Xtra" in the tooltip, followed by "MTP Device" in the new hardware tooltip. Finally, Windows announced that there was a problem installing my new hardware and that it may not work properly.
Sure enough, when I went into Device Manager, my Zen Xtra was showing as an MTP Device with an exclamation point on it. More specifically, it specified the status of, "This device cannot start (Code 0)."
Prior to the installation of Windows Media Player, the Creative Zen Xtra showed in device manager with the following characteristics under the heading "Windows Portable Devices":
Name: NOMAD Jukebox Zen XtraDriver Version: 5.2.0.0 dated 8/30/2004Digitally Signed by Microsoft Windows Component Publisher
Driver File Details:C:\Windows\system32\wpdusb.sys - v5.2.3802.3802 built by dnsrv(bld4act)
Windows Media Player changed this to the following (the device now shows up under "Portable Devices"):
Name: MTP DeviceDriver Version: 5.2.5326.4762 dated 2/22/2006Digitally Signed by Microsoft Windows Component Publisher
Driver File Details:C:\Windows\system32\wpdusb.sys - v5.2.5358.4827 (WMP_.060509-2009)C:\Windows\system32\DRIVERS\wudfrd.sys - v6.0.5348.0(winmain(wmbla).0604-339)
The file wudfrd.sys is NOT digitally signed in this case.
As of now, my Zen Xtra is completely unusable on this system, and I need to sync it with my laptop for the time being, which still has WMP 0 installed on it.
Is this a bug with WMP beta? Is it a problem with my firmware? Since this is PlaysForSure compliant firmware, and it worked flawlessly with Napster and WMP 0 (before the MTP driver was updated), it would seem to be a WMP beta issue. I'd like to hear more official confirmation on the subject, however.
Some general details about my system are:
Microsoft Windows XP Professional with Service Pack 2Verified GENUINE Microsoft operating system using Genuine Advantage ValidationIntel Pentium 4 CPU 3.2 GHz, Hyper-Threaded processor2.00 GB RAM
Windows Media Player Version: .0.5358.4827Napster Version: 3.6.0.7 (US)
Any recommendations? Fixes? Some have suggested rolling back the WMP installation, but I would like to consider this option only as an absolute last resort.
Best regards,Matt

Ok, this worked out accidentally - but happily
I first installed the driver - not the media source - but the driver for the device.
After that the windows device manager yellow sign disappeared - apparently the device driver was registered by windows.
Then I Installed Mediasource 5 - the installation went thru fine.
Does anyone have any recommended updates to install, please also advise what benefits.
Thanks.

Help needed getting Zen Micro to work on new

Hi there, I am having a tough time getting my new PC to interact with my Zen Micro
I have installed all the required software, I have done all the updates (or at least I think I have)
I have upgraded my firmware to ver. ..0 and yet i still have the problem.
The organiser seems to see the files in the player, but it cannot transfer them to the PC (or the PC to the Player). I cannot seem to access the player while it is connected either.
So in short, I cannot transfer any of my music to my PC (4Gb worth).
I have sent support requests, and I got an auto response to upgrade all the software versions, and the firmware, which I did. I have gone through the auto-detection process on the Creative site, and it recognises my player, and its newly updated firmware version, and only gives me recommended update options, nothing essential, or critical.
So I'm pretty much stuck. also, how do i know that firmware ver. ..0 is the most updated for my product, as the support mail seems to talk about ver. 2.xx.xx which I'm nervous to start downloading as my player is now over a year old, and i fear that it may not support the newest technologies.
Any help would be greatyl appreciated
Thanks in advance
Sparky
P.S. I am still running my old family PC (Windows 98, with all the creative software original purchase versions running), and when I connect my Zen to this machine it works fine, so I guess that means that the files are not corrupted thankfully

For the Zen Xtra right?
I went to and chose MP3 Players > Zen (Hard Disk Dri've/MicroDri've) > Zen Xtra, then Get Files.
The driver was listed there, but you want to download:
Jukebox Driver version .26.02</LI>
Creative MediaSource Software Update version 2.03.29</LI>
NOMAD JukeBox Type 2 Version .0.03 (English) Web Release</LI>
Creative NOMAD Explorer (Version 3.0.0) (if you want to use Nomad Explorer)</LI>
You then want to:
install the driver</LI>
turn the Xtra on and connect to the PC and let the driver install (should be automatic)</LI>
with the Zen still connected to the PC install MediaSource (it needs a Creative product present to validate the install)</LI>
install the Nomad Jukebox Type 2 version (this is required to get MediaSoruce to work with the player)</LI>
If you want, install Nomad Explorer</LI>
That's all you should need to do.

Zen Xtra 30G Works with Windows Vista Home Ba

I am writing this to help anyone who has experienced this problem. I don't know if this fix will work for all of you, on other versions of Vista, or if you have other firmware installed will not work for you. Note, since Vista was released Microsoft or Creative could have sent them updated drivers without anyone knowing. I have had Vista Home Basic for year now.
After some tweaking, the Windows XP drivers worked on Vista Home Basic.
I then use Nomad Explorer meant for XP to manage the MP3 files on my Zen Xtra.
Firmware .20.08 30G Zen Xtra
No Playforsure installed
Vista Home Basic
User Account Control OFF
Here were my steps:
Connect your Xtra to the PC running Vista.
When first connected to Vista without drivers installed, Vista attempts to find drivers, if it finds them you'll be golden, but as I know there are no such drivers, if not it should return unsuccessfully.
Download the latest USB drivers and 2004 Nomad Explorer from Creative's website.
Run all as administrator.
Right click properties to set to run these programs in Windows XP Service Pack 2 emulation mode.
Install the driver, it will hang and time out, and some drivers will be installed.
Install Nomad Explorer, if enough drivers were installed it will finish installation.
Unplug the Xtra.
Reboot.
After Vista is booted, plug in the Xtra. It will now cause the driver to load, with a bizarre off sized icon. It will view files but you cannot open or access files. Media Player will try to boot and bomb, it cannot access files nor downloaded them.
Now boot Nomad Explorer. It runs through the Xtra drivers. It will work like XP but look like Vista.

Hi i tried the 3 posible solutions with not good results:
- The driver from nomadworld is the same, so it didn't work either
JB3_PCWDRV_US__26_02.exe
- I tried to disable my antivirus, but I still get the same error at the end of the installation:
"An error occurred while setting up the driver"
- I saw the last reply about the device manager, but there's no Zen on the device manager, i had seen when a device have a error because of the driver, but in this case it doesn't appear anything.
I didn't understand which .inf I need to modify, could yopu explain me more? please.
May be is related to this, because my drivers path is "C:\Archivos de programa\Creative\Jukebox 3 Drivers", probably there's some path hardcoded in the installer.

Can't get airport express to work with new wireless router

I just swapped out a linksys wrt54gl for a linksys E1200 wireless router on my home network. My PCs and iPads, and TV all made the switch to the new network fine, but the airport express isn't working. All I want to use it for is to transfer iPad audio to my home speakers. but my iPad AirPlay shows the old Airport as an option, I can switch to the Airport, no sound comes out the home speakers, then the iPad reverts AirPlay back to iPad. This model Airport just has power, USB, and LANA ports, so it doesn't seem like it would be complicated. A CAT 5 cable goes from the airport WAN port to one of the ports on the back of the new wireless router. What did I overlook?

I thought I'd jump in here with you network experts for some help with a related networking problem.
Equipment: iMac 24-inch, Early 2009 2.93 GHz Intel Core 2 Duo; 2 MBP w/Retina Display; AirPort Express version 7.6.4 (Conncected Using: DHCP; Router Mode: DHCP and NAT); Comcast/Xfinity Gateway 1 Modem w/2.4 GHz WiFi.
#1. Comcast forced me to change modems to their Gateway 1 saying mine was at “End of Life.” Previously, my home network was set up with AP Express and worked fine using my iMac as a server. After installing the Gateway 1, I could not get my network to work after repeated calls to their support, online chats, trial and error, reading community chats and articles, etc. I put the Comcast modem in passive mode using the “Bridge” setting and re-established my network with my AP. I’m using my iMac as a server for file sharing with my two MBP’s. The network isn’t recognized in sleep mode and will not wake from sleep and I can’t find it or Connect to Server when the computer is asleep. I’ve tried all combinations within the Energy Saver/Screen Saver/Security preferences. I’ve reset the SMC and other like resetting to factory defaults. How can I fix this and what are the correct settings for my home network to function again with my AP Express?
#2. TimeMachine stops doing backups when the computer is in sleep mode, understandably because I’m not making any changes on the iMac that need to be backed up. But using my laptops on the network, I am making changes in shared files that are hosted on the iMac that I would like backed up. I cannot get the schedule feature to work to wake up the computer long enough to do a backup nightly because, as a security feature, I log out after 30 minutes of inactivity. I understand the schedule doesn’t work unless you’re logged in. Is there a way for me to make this work?
Thanks!

How do I get usb superdrive to work with new macbook pro. superdrive rejects cd ?

Just purchased new system. (never had an apple before) so I am all at sea. followed the instructions to uodate the system. whenI inserted a cd with program to be installes foe a Mac, it was ejected. inserted a cd with 'jpeg files only on it it too was rejected, with no message. Am I missing anything?

I suggest you return the Apple Superdrive and buy any other brand external DVD drive that connects by USB port.
Any brand will work with your Mac, cost less and work better.

Cannot Get My Powerbook To Work With New Hard Drive

My powerbook (1.67 ghz, 2 gb ram, 80 GB original hdd) was running out of room on the hard drive, so I purchased a WD 250 GB hard drive IDE to replace it. I haven't really done much on my powerbook prior to this, so I wasn't sure exactly if any problems had occured before I did this. But I replaced the drive and tried to boot from a CD and could not do it. I was using a Tiger Retail disc because I can't find my restore discs. I never had any problem reading my discs prior to this, as I have a DVD/RW drive and it has never failed on me. I tried booting from other discs as well and the same problem occured. So after several failed attempts, I connected my powerbook to my ibook through target mode and was able to install the OS on the partition of my powerbook. After completing the install, I was able to access the powerbook partition through the ibook and everything seemed fine. I unplugged the firewire cable and tried to boot my powerbook. The first time I did it, it took me past the white and grey apple screen and stuck on the blue screen, everytime after that, it hung up on the grey and white screen. I tried resetting everything through open firmware and zapping the PRAM, but no change. I tried booting into safe mode and it hung up at the grey and white screen. I was able to boot into single user mode and ran the check utility and everything came up ok. I reconnected the powerbook to the ibook and ran disk utility that way and repaired all permissions. It still has hung up on me. I've been trying to get this to work for almost 8 hours and nothing has worked for me. I'm starting to think its something really serious like a hardware failure. I don't know what version of tiger my powerbook shipped with and I'm not sure if having just 10.4 would cause this issue. I tried removing the added ram and everything as well. I hope someone can give me some things to try and hopefully get it to work. I'm pulling my hair out on this one. Any help would be greatly appreciated.

One way to know if it is a hardware issue (or something you may have done in the DIY upgrade process, sorry) is to try putting back in the old stock 80GB drive and see if everything works well.
If YES, then your PowerBook is fine and it is your new drive that is faulty. Return it or get a replacement under warranty (if relatively new, maybe you don't need to use the warranty).
If NO, then something has happened during the upgrade process.
That's my first diagnosis.

Can't get 4050n printer to work with new Desktop Computer: running XP

I have a new Desktop Computer, dual processor, which is running XP and MS office 2007. I had my 4050N HP Laserwriter hooked up to my old desktop (which failed in the last two weeks, blown capacitor, etc) and it worked fine with XP on that computer.
So I downloaded the drivers I found for HP 4050N running XP, and can't even get a test page. The connectors seem to be ok. I had to buy a parallel port to USB cable and I have that plugged into the USB port at the back of my new desktop.
Any ideas of what else I should try? If I had a computer virus with the old machine, could it have affected my printer somehow?
I'm at a loss.
Thanks!

Since you mention doing an upgrade I would be inclined to reset the printing system and then add the R2880 queue again.
Open System Preferences > Print & Fax
Move your mouse over the Printers list
Hold down the Control button and click the mouse
Click the "Reset printing system ..." popup
Restart your Mac
This will remove your print queues but not your printer drivers. So you will only need to add your printer queues again.

Can't get secure wlan to work with new guest wlan

Dear Support,
I'm having a nightmare! where I can seem to get either one wlan to work or the other but not both together.
I posted previously and reconfigured as per the suggestion, however the problem I get is that the secure wlan client associates, then de-associates after roughly 30 seconds with both a guest (no security) and secure (eap using ms ias as radius server)
my previous post is;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Security%20and%20Network%20Management&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddcfe12
and the log shows the following, obviously the client is set to connect automatically.
*Mar 1 00:04:35.105: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:04:51.391: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 000e.35f8
.5d13 Associated KEY_MGMT[NONE]
*Mar 1 00:04:51.506: %DOT11-4-MAXRETRIES: Packet to client 000e.35f8.5d13 reach
ed max retries, removing the client
*Mar 1 00:04:51.506: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 000e.35f8.5d13 Reason: Previous authentication no longer valid
*Mar 1 00:05:15.176: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:05:32.703: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:05:58.780: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:06:16.141: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:06:40.759: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:06:58.145: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:07:00.560: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:07:18.020: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:07:43.902: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:08:01.254: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:08:16.172: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:08:16.737: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:08:37.397: %DOT11-6-ASSOC: Interface Dot11Radio0, Station AP-CDC#2 00
13.cefd.48ca Associated KEY_MGMT[NONE]
*Mar 1 00:08:54.732: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating
Station 0013.cefd.48ca Reason: Sending station has left the BSS
*Mar 1 00:08:57.193: %DOT11-4-MAXRETRIES: Packet to client 0013.cefd.48ca reach
ed max retries, removing the client
Thanks in advance for your assistance.
Any prompt reply will be greatfully received. I also rate responses.
Thanks again, regards, Adrian

Hi Ben,
Please find attached AP config, I can access the switch at the moment, but the config is fairly basic, trunk port with two vlans and vlan 1 as the native.
here's the ap config.
AP-CDC#2#sh startup-config
Using 2989 out of 32768 bytes
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-CDC#2
enable secret 5 $1$LQ1O$NKYZoYAeiahKw0805kLHg0
clock timezone GMT 0
clock summer-time BST recurring last Sun Mar 1:00 last Sun Oct 1:00
ip subnet-zero
ip domain name wlan.internal
aaa new-model
aaa group server radius rad_eap
server 10.10.10.2 auth-port 1645 acct-port 1646
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 vlan-name dmz vlan 2
dot11 ssid Secure
vlan 1
authentication open eap eap_methods
authentication network-eap eap_methods
dot11 ssid Guest
vlan 2
authentication open
guest-mode
username Cisco password 7 062506324F41
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode wep mandatory
ssid Secure
ssid Guest
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0
54.0
no preamble-short
channel 2412
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 10.10.10.49 255.255.255.0
no ip route-cache
ip default-gateway 10.10.10.253
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host 10.10.10.2 auth-port 1645 acct-port 1646 key 7 xyz
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
AP-CDC#2#
Thanks again, regards, Adrian

Can't get old scanner to work with new iMAC

I have an old scanner, Epson Perfection 4870 Photo that I can't get my new iMAC to install in PSE6 like I've had in my older computers. I've installed all the software (plus I used my old laptop to transfer files/information when I initially started the new iMAC. When I go into PSE6 it is not under the import area that it used to be. Do I need to go manually drag the file in the hard drive to another folder? Thank you.

Most likely the problem is with the driver. I have the same scanner at work and this is what I had to do to get it to work. Because you are running PSE6 which is a Universal Application on an Intel Mac, in order for the plugin to load within PSE it must also be a Universal plugin which it's not. Epson claims these drivers that were released in 2006 are Intel and 10.5 compatible. What you have to do to get it to work is Open up Epson Scan Utility in order to scan because the Scan Utility will run as a PPC Application. You can call Epson to confirm but if they try and tell you how to run PSE in Rosetta that is not a good solution.
George

Can't get Epson NX510 to work with new iMac

I am new to Mac, and I apologize if this is the wrong forum to this question, but...
Apple threw in an NX510 scanner/printer/copy/fax when I bought my new iMac a couple of months ago. Printer/copy functions works great. But I cannot get the scanner function to work.
Can anyone help me figure this out? Thanks in advance.

Try this from the Epson FAQs
http://www.epson.com/cgi-bin/Store/support/supAdvice.jsp?BV_UseBVCookie=yes&type =highlights&noteoid=142167#can%27t%20scan
For Drivers
http://www.epson.com/cgi-bin/Store/support/SupportSnowLeopard.jsp?BV_UseBVCookie =yes
Message was edited by: WZZZ

Can't get my printer to work with new OSX 10,6?

I upgraded to snow leopard 10.6.3 so I could use the new Touch 4th generation. Everything was great until I tried to use my epson R2880! I keep getting
errors. It also says the printer is not registered. I have downloaded software updates, font updates, etc. no luck? Any ideas? thanks

Since you mention doing an upgrade I would be inclined to reset the printing system and then add the R2880 queue again.
Open System Preferences > Print & Fax
Move your mouse over the Printers list
Hold down the Control button and click the mouse
Click the "Reset printing system ..." popup
Restart your Mac
This will remove your print queues but not your printer drivers. So you will only need to add your printer queues again.

Old Apple ID disabled been hacked. Can't get iCloud email to work with new ID

old Apple ID disabled
please help

Hey there Tamsin,
If I understand correctly your Apple ID has been compromised. I recommend you reach out to our Account Security team immediately for additional assistance. Please note that you will be asked to verify your account information.
Apple ID: Contacting Apple for help with Apple ID account security
Thank you for using Apple Support Communities.
Cheers,
Sterling

Zen Micro Photo not working with new XP SP2 install

Okay so my Zen Micro Photo stopped being recognised on my computer about ten months ago when I upgraded to WMP (for BBC iPlayer - it's compulsory to have it). Anyway I li'ved with this and have now got thoroughly sick of the same songs and nothing new so I have done a fresh install (on a brand new hard dri've) of Windows XP SP2 WMP9 with the sole intention of using this install/hard dri've?for the player. I used the original installation disk and it prompted me to upgrade to WMP0 as I installed everything. There were no errors during the install and I rebooted when prompted to.
When I attach the player it is recognised by the machine (task bar icon and correctly labelled in System > Hardware > Device Manager which reports it to be?working okay) but the Creative media software says "player not attached" when it is. It is not visible on My Computer as a dri've so I STILL have no access to the player. Player screen reports "docked" with a logo and is flashes a charging icon. Driver v5.2.0.0. The player plays fine but hasn't had new music on in almost a year
There is nothing else on the XP install (IE6 and everything - argh!) I did the registry permission tweak thing mentioned?here:?http://support.creative.com/kb/showa....aspx?sid=9287?but it didn't do anything.
Any help greatfully received!

Re: Zen Micro Photo not working with new XP SP2 install. Have you installed this plug-in?
Creative PlaysForSure Devices Plugin 5.00.36 for Creative MediaSource 5 Player/Organizer
Filesize : 27.9 MBDownload

Zen sleek not working with vi

I have a Zen sleek, and I have just got myself a new computer with windows vista. How do I get my Zen Sleek to work with vista? This is very frustrating. I have tried downloading the software from the Creative site, but during setup it says that no product can be found. I get this message both with and with my zen sleek connected to my computer.
What to do? Please help.
kind regards
Jacob Skeel Nielsen, Denmark.

OK, your Zen Micro worked with your older computer, correct?
Was your older computer an XP machine or an earlier version of Windows?
As far as I know, XP requires the PlaysForSure firmware to work with your Zen Micro. You need Service Pack 2 and Windows Media Player 0 too.
You can find the drivers, firmware and software that you need by clicking the Support menu on the Creative banner at the top of the page-> Downloads->MP3 Players-> Zen-> Zen Micro, select your language and Operating System and then the drivers, firmware and software that you need.
Be sure to click the Show Details... pop-up for more information and instructions.

Getting Zen Xtra to work with new compu

Similar Messages

Maybe you are looking for