Graphic and Rendering artifacts

I am attempting to overclock a Neo2-LS with
a P4 2.4b at 160 FSB.
At 150FSB running at 2701mhz the system is stable as a rock.
But at 160FSB I have been noticing some graphic artifacts
while rendering mpeg2 (DVD). In Pinnacle Studio I start to
see little green dots in the preview screen and then on the
mpeg file I see these artifacts as well.
The system does not crash and I do have sound but I have noticed my sons game does not behave at this overclock either.
I have my Core voltage at 1.7v memory at 2.65v and AGP at
1.6.
Running AGP/PCI bus at 67/33
Temps do not go over 55C on any chips.
Anyone have any ideas if there is a way to get the graphics/rendering to stabilize at this overclock level?

AGP Voltage manipulation is a must for overclocked systems, where the AGP bus and/or video card is overclocked. I run my R9800 Pro at 441/371 with no artifacting. But ONLY if I raised the AGP voltage. I run my AGP Voltage at 1.8V
MR BREEZE
P4 3.0G 800FSB @ 3.45 G/230(924)FSB
MSI 875P Neo FIS2R Bios v1.5
Kingston HyperX3500 1GB Dual DDR433
ATi Radeon 9700 Pro @ 441/371
WD1200JB Primary Drive
Pioneer DVR-105 (unlocked firmware 1.33b)
2xWD2000JB on IDE in RAID-0
Antec TrueControl 550
Sandra MAX3! CPU: 11696
Sandra MAX3! Mem: 5565
3dMark2001SE: 20995
3dMark2003: 6848

Similar Messages

Pdf (with graphics and text) in the email body

When I place an pdf (with graphics and text) in the body of my email using Mac Mail my recipient sees them as attachments only. I am trying to find a way of presenting a formatted email with graphics that will appear the same way to all recipients, but a pdf frequently ends up being an attachment instead of staying in the body. The pdf file doesn’t seem to always show up in the body as created. Is there a better way to accomplish this?

You have no control over how your email maybe rendered by other email servers and client side software.
Attachment Tamer may give you a few more options but it does not guaranty the end result.

Graphics and images look wrong in Safari 4.0.3

Hello
Since upgrading to Safari 4.0.3 graphics and images in websites look low quality. As if they are being rendered with 256 colours or they are heavily compressed. The strange thing is that about a week ago the problem disappeared and everything looked sharp and great, I ran the new version of Cocktail last night and now the problem is back! Could be a coincidence but either way I can't fix it.
Any advice would be appreciated
Andy

Greetings,
Caches cannot be emptied automatically, nor can Web Page Previews, which is used for the Top Sites and Cover Flow features in Safari. You can empty those folders, but Web Page Previews will simply be refreshed with new images as you browse.
If you don't want to use the Top Sites or Cover Flow features in Safari 4.0.3, you can disable it completely, and then you could empty those folders (com.apple.Safari and Web Page Previews) and then Lock the folders so any cache files from browsing would be deleted when you quit Safari.

Seeing pink and green artifacts when using AIR 3.5 beta

Hi,
I'm noticing that, when using the 3.5 beta SDK, some display elements are being rendered with strange pink and green artifacts. Below are screenshots of this occurring (most prominently on the spark buttons) on three devices:
Galaxy Tab (running android version 2.3.3)
Cropped version (to make the problem more visible, in case the previous image was scaled down):
Nexus 7 (running 4.1.1)
Cropped:
Galaxy Nexus (running 4.1.1)
Cropped version:
By contrast, here is a screenshot of the same application running on the Galaxy Nexus, when compiled for 3.4:
Cropped:
Any ideas on why this is happening?

Same here on Galaxy Tab 1 and Galaxy S1 ! And no spark component here, only simple drawings...
Incredible to see such a "visible" bug in this beta...

What installation of windows for powerfull 3D modelling and rendering.

Hi everybody.
I need a config to use windows in a very compatible, easy to use and powerfull way. No simple bootcamp installation as I will be rebooting all the time, between mac apps , Adobe CS (OSX) and Rendering Software (Shot/Bunkspeed -windows).
So what installation of windows should I have? Virtual Computing or Virtualization? and what Software for everything to go fast enough?
Then What hardware should I have for everything to run well? Any special requirement?
Thanks for the answers.

I would have posted in Mac Pro forum. Why do you say "simple bootcamp" as actually a VM is much easier and less fuss but will never live up to what you need.
A VM will NEVER be as fast or as well as running natively, especially with 3D or anything hardware resource intense.
Maybe time to build a PC or switch CS5 to Windows (it does have some advantages though CS5 caught up some) but to use CUDA you would need the only nVidia Apple sells probably.
Run OS X off a RAID.
Put your VM on its own drive or array.
Normally I would say CS5 etc then the Quadro 4000 would be ideal as 2nd video card.
Most people install Windows natively first on its own partition, what Apple calls "Boot Camp" but overuses the term, so that they can dual boot; then, install Parallels or Fusion so that they can use Windows as a guest OS under Mac OS when they don't need full access to all the RAM, more cores, and direct access to graphics.
Easy to use to me, Windows 7 or OS X, both are fine, though Windows on Mac has some limitations.
People have run multiple VMs on Mac Pro and find performance to be good thanks to dual processor, plenty of RAM and multiple fast hard drives.
I would install Windows on its own hard drive first, Windows 7 Pro 64-bit (System Builder is fine but you need Pro to use more RAM and dual processors).
http://discussions.apple.com/forum.jspa?forumID=1320

Strange previews and renders appearing with blue rectangle glitch

I am getting these strange artifacts on my previews and renders in PP Cs6. The footage is proresHQ. I have attempting adjusting every setting I know and doing a clean reinstall of PP. Any ideas?

Hi NoxPhoenix,
Have you updated your GPU drivers lately? Try that.
Thanks,
Kevin

Clean sharp psd graphics and premiere titles until I render?

Hello,
I'm importing beautiful layered psd graphics and creating titles with premiere on a 720P DVCPROHD timeline.
These graphics and titles look great when they are still red bar...then after I render I get the same old ugly jagged edges I have always seen.
Can anyone explain why this is? And is there a fix?
Thanks for your advise in advance!
Mark

Thanks for the input.
I am viewing on my computer monitor because I don't have a video board for external output. I need to render out to a DVD for final playback, so I am stuck making adjustment on my computer screen. I am editing a progressive timeline so isn't my "Premiere program monitor" computer screen accurate for progressive material or is premiere always converting to interlaced?
My preview playback codec is set to DVCproHD 720p.
I just now tried setting my render quality and bit depth quality to max...this slows down the render time and the rendered graphic images still become jagged.
If I render out to a progressive DVD should this jagged edges clean up?
Rushing to get a project out.....don't have much time to investigate it.
Thanks,
Mark

HELP: My Videohive After Effects project is rendering artifacts! AE CS6

Hi all,
HP-HPE 510t
i7 2600 @ 3.4GHz
16GB Ram
Windows 8 x64bit
Nvidia GTX 660 Ti
I purchased a Videohive After Effects project with motion gfx and video, and it is rendering artifacts in two places.
I'm exporting Quicktime + animation, tried + PNG, and + photo jpeg but all with the same results.
I even contacted the author but he cannot explain why either. The interesting thing is, it renders beautifully without any artifacts in AE.
Only on the export render do I see the black silhouette artifacts. Below are some photos of what I mean.
Please help? i'm trying to export the highest quality for youtube and am going to H.264 the lossless version.
It looks correct in AE:
[URL=http://s10.photobucket.com/user/mystickid/media/ItisworkingcorrectlyinAE.png.html][IMG]http://i10.photobucket.com/albums/a135/mystickid/ItisworkingcorrectlyinAE.png[/IMG][/URL]
But with black artifacts in lossless render?
[URL=http://s10.photobucket.com/user/mystickid/media/promoartifact2.png.html][IMG]http://i10.photobucket.com/albums/a135/mystickid/promoartifact2.png[/IMG][/URL]
[URL=http://s10.photobucket.com/user/mystickid/media/promoartifact3.png.html][IMG]http://i10.photobucket.com/albums/a135/mystickid/promoartifact3.png[/IMG][/URL]
http://s10.photobucket.com/user/mystickid/media/promoartifact1.png.html

Thank Rick,
Only reason that I'm using photobucket instead of the built-in image embeddor (camera icon), is because it doesn't seem to be working for me. All I get is an empty dialog box, tried also with video but that one seems to be working properly.
maybe ill try firefox.
any solutions for the artifacts??
My output module settings so far have been..
tried:
1) Quicktime + Animation (lossless) quality 100
2) Quicktime + photo jpg
3) Quicktime + PNG (lossless) quality 100
4) Quicktime + H.264 30mbps
tried rendering again with "Render Multiple Frames Simultaneously" turned off...still getting artifacts only on these text offset animation frames.
still looks perfect while in after effects.. I restarted my computer, I cannot figure this out.
Help!

Poor quality graphics after rendering

Hi- I'm importing still pics into FCP v5.1.4 at 300 dpi at size exported (took a still frame from captured video and used it as a template in photoshop). The graphic looks great but after rendered, it's of poor quality in canvas.
Sequence settings DV-NTSC 48KHz - Frame size 640 x 480 aspect: NTSC 4:3 > Quicktime Video Settings-Best Quality DV/DVCPRO - NTSC.
I changed the sequence settings to Animation at best quality which rendered better, not great, but took a long time with big files. I'm not sure if this is the way to go.
Should I match FCP video settings > Sequence Presets to Sequence Settings?- as I see no "Animation" in Sequence presets.
I just want to out put sharp good quality graphics and type- is there a recommended set up in FCP for efficient and best quality graphics and type?
humbly yours, j

Thanks for all your quick responses and good input. I forgot to mention that the stills are with video footage- should be "Interlaced" ?
I have come up with a pretty good solution using "Animation" setting. The following are my notes:
I changed the sequence settings to Animation at best quality which rendered better, not great, but took a long time with big files. I'm not sure if this is the way to go.
However when exporting using Quick Time Movie output is jagged and files were big: 60 to 117 MB.
Outputting to Quick Time Conversion was better using Animation compression at highest quality but file was too big. Changed that to medium and a reasonable 7.65 MB resulted with a reasonable quality when viewed from Quick Time.
Issues to contend with- will iDVD use this file and display quality? If that .mov file be of quality if put into a FCP timeline?
The DVD came out OK. I will play around with sized 72 dpi's for stills.
Thanks again! j

Rendering artifact problem on scroll

Hi forum
I have built a forum manager and all is well and good, except there seems to be a problem with artifacts when scrolling the form. Screenies below:
This is what it looks like before any rendering problems
Here you can see its rendered incorrectly when i've scrolled around.
Does anyone know what the problem is? Its worse on some browsers and on older machines. Is there a way to stop this or reduce the risk of it happening?
Thanks alot
Tom

I have been struggling with this problem a lot as well. Exactly the same. And I can't find toot anywhere about it.
I have found that setting your wmode to "window" fixes the problem for me. I see no rendering artifacts at least. However that isn't an option for me in my current situation since there are other elements on the page that must be renderered on top of the player.
If you have figured anything else out then I would be very very interested in knowing how you got it fixed!

Background graphics and link icons do not display even after downgrading flash, emptying cache, reinstalling recent and older versions of firefox

sometime today, firefox 14 began not displaying the background graphics and link icons on every site I went on from my laptop. It would display this information when I changed the rendering engine to the explorer platform. I have removed the flash player 11.3 from the computer; re-installed flash 10.3 recommended from the troubleshooting page; restarted the computer; same problem. Did the same with the Java plug-in with the same result. Disabled all extensions and restarted Firefox with no change. Examined the sites on a different laptop using version 10 of Firefox and everything worked fine! Reloaded older version of Firefox on original laptop, restarted computer, same problem on older version. Updated to latest revision, listed below, and same problem. Went to desktop computer using version 14, and same thing is happening there also. (I have not done anything to this system yet.)

All of the items contained in both of the reference documents were already active on each system. I have created a zip file with four screen capture pictures showing what I'm dealing with. The first picture shows what the site looked like yesterday morning; the second shows what happened when I refreshed the screen this morning; the third shows what happened when I switched the rendering engine on the same tab this morning; the fourth shows what happen when the tab was switched back to original rendering engine. The file is at:
[http://charisacademy.org/pictures.zip This location]
Please consider this for a moment: I am having to answer these questions from you using my iPad because the graphics at the top of this window which control the type-input will not display in Firefox while the post buttons will. Let me know if you can't get the picture file and I'll find another way to get it to you.

Odd Graphical or Window artifacts What is it?

Hello.
I have in the past week had some very strange graphical "ghosting" or "artifact-ing".
I can not determine the cause but am concerned that it may be a hardware issue and if so
I would like to head it off before it crashes....
What happens is this:
1. The system will "freeze" (no beach ball or Kernel panic it will just freeze with the exception of the cursor which will move freely with the mouse)
2. Then one of the windows which I attempted to move on system freeze will get "Garbled" and a section will be "re-mixed" and stay in the area it was previously in.
(see pic here http://www.markofman.com/files/graphics_issue.jpg )
3. The time before last my "force quit" window had part of the safari browser displaying within the area where the open apps should have been...
I am worried that this may be my graphics card or worse my motherboard...
maybe it is RAM? (I put some new ram in a month ago...)
are there any tests or has anyone experienced this before?
any help is appreciated.
thanks
2 x 2.66 GHz Dual-Core Intel Xeon MacPro
13 GB 667 MHz DDR2 FB-DIMM
NVIDIA GeForce 7300 GT

I'm having a similar issue with my Mac Mini (late 2009). for the past two weeks, I am experiencing multiple vertical red dost/lines in numerous places on my monitor. I can't take a screen shot. it does not show in the screen shot. I have taken a video however.
The program it affect is Safari. It freezes safari regularly with a weird black flickering screen that take up 80% of the screens. And the only way to escape is to hard boot(or if i'm lucky i can get to the restart button...or simply quit Safari) Then it works fine. But the artifacts still remain.
I aslo thought I might have hardware or fan problem. I original thought my nVidia 9400m was trashed. But...it works perfectly in bootcamp...(strange)
I've been an apple tech on and off since 1984. I've done everything that i can find on the boards ( remove and test RAM: refreshed and reinstalled clean OS) This one is baffling. Because it still shows up with the startup disk. But not bootcamp.
I have one more month left on my applecare. it might be time to take it in
Thanks for listening. Any leads would be very welcome

Mac Pro Freezes and horizontal artifacts appear on Display

My Mac Pro display began glitching while using After effects yesterday. The display colors became very strange and horizontal artifacts appeared. Everything froze and I couldn't force quit. After a minute the problem cleared up and all was well.Then today the glitches got more frequent and the whole machine froze up showing the same, but random horizontal artifacts along with strange colors. I can't move the mouse or force close programs. I've had to power off the machine by holding the power button down. I did that twice today and both times the computer started normally and then the problem came back a minute after start up. The mouse and keyboard also started losing power yesterday and today. A quick unplug and plug in fixed that problem. I have been using After effects 8 hours a day for about 4 weeks straight Perhaps that but some strain on the graphics card. Any help would be greatly appreciated. Thank you!
Here's a link to a picture of what the display looks like:
http://s1254.photobucket.com/user/timfoxweddings/media/photo_zps70928015.jpg.htm l

Those sorts of artifacts are unlikley to be a software or configuration problem.
The Apple firmware 5770 (about US$250) works in every model Mac Pro (65lb tower), but may have minor problems if you play copy-protected movies. It requires 10.6.5 or later, so you would have to upgrade if you are still on 10.5.8.
You lose AppleTalk-over-Ethernet in the 10.5 to 10.6 transition, if that is an issue for you.

Slow FPS, graphics and choppy video when connected to a Mini-DVI cable to external monitor on Macbook Mid2007 4GB RAM

Hi,
I have a Mid-2007 Macbook white. I have upgraded its memory to 4GB. Snow Leopard was working great, and I said to myself maybe it's time to upgrade to Lion.
After the upgrade all was well. However, a big problem occurs when I plug in to the Mini-DVI display port with the HDMI adapter, to connect to my Sony LCD HDTV. The whole graphics and video slow down, everything is choppy. Quicktime and VLC video playback is strobe and choppy looks like very low Frame Rate. Cannot watch anything, not HD nor low resolutions. The entire computer is slow when the cable is connected.
Things I tried:
*VGA adapter seems to work fine - it's the digital display output that probably causes that.
*Running it through a new user.
This never happened on Snow Leopard. i'm considering to go back. However, I am wondering if there is a way to fix this minor problem.

Update:
We solved the problem. Weird solution but now it seems to work. I plugged a VGA adpater and played with the screen rsolutions to try and watch a movie well on my LCD screen. I changed the screen resolutions but I couldn't revert back to the default settings. Pressing "Detect Displays" didn't do anything.
Here is the interesting part: When I placed back the DVI-HDMI adapter, suddenly everything worked fine!!! There was no choppy videos, no low fps, works prefect.
Something weird is going on here, but I'm happy I managed to get the DVI to HDMI to work because I was about to removie Lion and bring back Snow Leopard.

Is there a way for a form user to load graphics and text in same field?

I am aware that you can load text into a text field and graphics into an image field. However, I would like to load a document containing text and graphics (e.g., MS Word or RTF) into a single field on a PDF form. Is there any way to do this?

Paul,
I believe that the example of attaching a file that you have provided will solve the problem. I am using LiveCycle Designer, so using the code that is in your example should be no problem. The end-user will use Adobe Reader, so as you mentioned, I will use Acrobat to extend the features so that the form can be used by Reader.
Thanks so much for your help,
Daniel
From: pguerett <[email protected]>
To: Daniel Beinart <[email protected]>
Sent: Monday, April 25, 2011 3:03 PM
Subject: Re: Is there a way for a form user to load graphics and text in same field?
It is part of the PDF AcroForm side of things .....Are you using Reader or Acrobat to fill the form. If Reader then you will have to Reader Extend to make this work ....if Acrobat then you simply need to add some code. I have attached a sample that shows you how to do it if you want it.
Paul

Graphic and Rendering artifacts

Similar Messages

Maybe you are looking for