Hardware requirement for server

Hi,
I am a new french developper with Jdevelopper and Oracle 8i.
Could you indicate me a good configuration for the server machine for an application using JSP, EJB :
- memory ? 512 Mo is enough
- bi processor ? usefull or not really
- hard disk ? raid 0
The installation uses only Oracle8i (with its HTTP Apache server) - physically 2tiers.
Thanks you very much,

Hello,
The quorum disk needs only to have a few MB to hold the file used for arbitration. Normally if you're needing a disk vote, it can be extremely small (100MB or less is what most SANs can do, some can only do 1 GB or greater). The actual file size is a few
KBs.
MSDTC holds the DTC logs, so this will be sized to how much logging and usage of MSDTC is needed and used. If you're not using distributed transactions then it doesn't even need setup.
-Sean
The views, opinions, and posts do not reflect those of my company and are solely my own. No warranty, service, or results are expressed or implied.

Similar Messages

Hardware required for SAP DMS Server

hi all,
my SAP system is SAP ECC 6.0 EHP1 with oracle OS is linux , if we install DMS server on this same sap system or on saparate system. how much hardware required for DMS server. our mostly will be imaging documents.
Regards
Khan

Hi Khan,
maybe the information in the SAP online help could be useful under http://help.sap.com/saphelp_erp60_sp/helpdata/en/b2/c043a66fab11d1949500a0c92f024a/content.htm
Best regards,
Christoph

Minumum hardware requirement for Siebel Document server?

what is the minimum hardware requirement for Siebel document server?

To install the Document Server, perform the following steps:
Obtain the required hardware.
Install the Siebel Server.
Install third-party applications.
After installing the Siebel Server, you may have to follow some of the steps described in Configuring the Document Server. The Document Server is a component of Siebel eDocuments, which can be installed during installation of the Siebel Server. Consult with your system administrator to verify that the Document Server has been installed and configured according to the requirements listed in the following sections.
Hardware Requirements
The Document Server is supported on the Windows 2000 platform. To maintain stability and performance, the Document Server must run on a dedicated host machine. The Siebel Server on this machine should host one instance of the Siebel eDocuments component group. No other components should be running other than required system components.
To support more users, you can run additional instances of the Siebel eDocuments component group on additional dedicated host machines.
Installing the Siebel Server
Install the Siebel Server on the dedicated host machine of the Document Server. For more information about installing the Siebel Server, see Siebel Server Installation Guide for Microsoft Windows.
During installation, you will have the option to enable component groups. Select the Siebel eDocuments component group. Do not enable any other component groups.
This step can also be performed after installation is complete, as described in the section Enabling the Component Group.
Installing Third-Party Applications
You must install Microsoft Word.
To install Microsoft Office
Log on to the server machine using the same user account that the Siebel Server NT service uses. This user account must belong to the Administrators group.
NOTE: The install must use the same account to be used by the NT Service. The installer configures COM security settings so that the installing user account will have the correct permissions to access and launch the application. If the install uses an account other than the Siebel Server NT service account, errors may occur when the Document Server tries to launch the application.
Install Microsoft Office using a Typical, or complete, installation. Verify that your version of Microsoft Office will install the Web Authoring Tools (HTML) component with the Typical installation. If it does not, you will need to use the Custom installation option, and install all of the typical components as well as the Web Authoring Tools (HTML) component.
Start the applications that will be used by the Document Server. This forces the applications to register themselves.
Close the applications.
Regards,
Joseph Arul Dass

Hardware Requirements for a SCCM 2012 CAS with SQL Server Remote

The hardware requirements for a CAS server with SQL Server Enterprise locally installed are:
16 cores (Intel Xeon L5520 or comparable CPU)
64 GB of RAM
1.5 TB of disk space for the operating system, Configuration Manager, SQL Server, and all database files.
Does anyone know what the hardware requirements are if SQL Server Enterprise is remote from the CAS server? It's not listed. -Shane

Even though I am going to be strung up for even saying this, I do agree there is a use for a CAS outside of 100,000 users. If you do indeed have distinct admins managing their own images and apps in remote
locations then I see the benefit of a CAS. A remote ConfigMgr console connecting to a primary site would perform poorly. Admin A at the primary site would not experience any issues but Admin B would be in for a lot of work and waiting. Any
time Admin B needed to add an app or image it would have to be copied up to the remote primary site and then distributed back down. This is not the best scenario.
There are scenarios in company merger situations (and others I am sure) where the management of both locations has not been consolidated down to one location yet and is not going to be done as part of the deployment or upgrade. If you had a 2007 environment
it is going to be very hard to convince the admin at the remote location that this upgrade is going to be a good thing for him/her. There is an option for the remote admin to RDP into a server in the primary site but the image and apps still need
to be distributed down to the remote location. During testing this can be very time consuming.
I do agree that adding a CAS adds additional complexity but in some cases such as the one I described it is the right decision.
Thank you for the reply. And i totally agree that in some cases a design like that is a necessary evil (but not by our personal wants).
We had that design with 2007 (implemented before my time), and as you predicted EU admins complained about difficulty using the console RDP-ed into a box close to the primary site. The bandwidth to and from different regions is out of scope for me so I do what
I can with what I have. We too will be moving forward with a CAS hierarchy.
Administratively the other IT depts in other regions operate on their own. I dont handle any of the EU computers on a day to day basis whatsoever, etc. We're not merging but our IT shops operate with near independence.

Hardware requirements for Reports 6i server

Hi,
I would like to know what are the hardware requirements for installing Reports 6i server. We we would like to deploy all reports through the web and expect a maximum of 50 users to fire reports at any given time during the day.
Any help will be very much appreciated.
Thanks.

Hi Umesh. You need to read this http://service.sap.com/ides .Download the documentation to that version which it is pleasant to you and in it there will be all corresponding information about hardware and e.t.c.
Regards.

HArdware requirements for BW server

Hi all,
can anybody give me the hardware requirements for BW server.we are trying to install bw in production server only.
regards
vinnu.

HI
IBM Server 1:eServer Model p550
73.4GB ULTRA320 10K 1~~
146.8 GB 15K U320 SCSI Disk Dr as per your
4GB(4x1024MB) DIMMs,DDR
Software Preinstall
2w 1.5GHz P5 Proc,DDR1
I think Use ful for U
Ramana Paruchuri

Hardware Requirements for SOA Suite 11.1.1.4.0 on Exalogic Server.

Hi,
I am trying to establish hardware requirements for installing SOA Suite 11.1.1.4.0 on ExaLogic Server for development, testing, staging and production environment. What will be the ideal configurations you need for a 2 Node Cluster on Exalogic Server.
Any help will be appreciated.
Cheers,
Varun

"Can we have same configurations for production that enterprise deployment guide speaks about."
That is your own choice, maybe you want a different identity management system or do not want to use RAC etcetera.
You pick the components that are relevant to you and follow the guide to set-up these components.
To get acquainted with setting-up such an environment it would be wise to start with the webhosts and the soahosts, see if you can get to work.
"Whether we need to think about high availability system incase of production or will this configuration suffice the scenario here."
It discusses a reference topology for a high available environment and how to set-up the environment.

Hardware requirements for weblogic server 10

We plan to install weblogic 10 on our server. Does anyone know what's the hardware requirements for it (Windows)? I couldn't find the information on the online docs. Thanks very much!

might be this is helpfull for you:
http://edocs.bea.com/platform/suppconfigs/configs/windows2000/win2K_srvr_as_dc_100.html

Hardware requirement for running exchange 2010 on vmware workstation

Dear Team,I need to create a exchange 2010 sp2 on a guest os on vmware workstation.kindly help me out with the physical hardware requirements for a home user

Hey Mukund26,
Before I answer your questions, my suggestion would be for you to figure out exactly what you want to get out of running that Exchange lab. Are you trying to learn Exchange features like DAGs? Are you trying to learn about virtualizing Exchange? When you figure that out you'll be better able to answer question 1 since you may not need all of those virtual machines.
Here are my thoughts on your questions.
1) It is probably technically possible to run 10 virtual machines on the configuration you have but you're going to have pretty bad performance. I would try to trim that down to only the virutal machines that you really need in order to use the lab how you want to use it. Here are some questions that may help you figure out what you need:
Why do you need two domain controllers? I don't think you need to worry as much about redundancy in your lab.
Why do you need 2 ESXi hosts and a vCenter? What purpose do they serve in this configuration? Are you trying to run the Exchange VMs nested under the ESXi VMs? If so, why?
Is there a reason why you want to separate out HTS/CAS from MBX in your lab? Combining all roles together can reduce the number of VMs you need. If you separate out the roles you'll need to allocate a lot of RAM to support all of those Exchange VMs.
2) Running a lot of virtual machines on a single 1TB SATA disk, especially a 5400 RPM disk, is going to be slow. It'll be especially painful when the VMs are booting up, rebooting, shutting down, etc.. Try to stagger the power on operations so they don't all boot at once. For example, first boot your DCs, then boot your HTS/CAS, then your MBX, etc. There is no doubt that configuration will be slow, so if you can get your hands on an solid state drive with enough space you'll have significantly better performance. For the purposes of a lab, though, it is probably ok if you can be patient.
3) I think the i5 processor will be just fine for this lab. Usually in a lab setting CPU performance isn't the most important thing so similar to above as long as you can be a little patient I think that CPU will suit you just fine.
As I said figure out what you want to get out of the lab and then you can determine how many VMs you need and whether or not you want to upgrade hardware. If you're looking to learn about Exchange 2010 in general I would suggest using multirole servers, getting rid of one of the DCs, and not worrying about virtualizing ESX/vCenter so that you can learn. If you're looking to learn about virtualizing Exchange 2010 on vSphere then let's figure out exactly what you want to get out of it and figure out what you can learn using VMware Workstation and what you really need vSphere for.
Best of luck!
Matt
http://www.thelowercasew.com

Hardware requirement for J2EE

I am on the evaluation of different technologies, I tried to get out the details of minimum hardware requirements for
Developers' Desktop,
Developement Server,
Production Server,
with regards to the J2EE. I could not find the same on any of the documents, I may be searching wrong docs. Can any one help me on finding the Hardware specs required for the above 3 categories?
regards
Mehul Trivedi

Hi Sudeep,
On the following links you will find the Composition Environment Product Availability Matrix and the installation guide of Composition Environment 7.1 Developer Edition.
SAP NetWeaver Composition Environment 7.1
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/e0e9cc7b-0469-2a10-d3a8-f4f04b30fb0b
For accessing the Product Availability Matrix document the service marketplace access is required.
Best regards,
Yasar

Hardware requirement For ECC6.0

Hi Everbody,
could u please help in providing hardware requirements for ECC6.0(IDES) for sandbox server.Like
O/s(32bit or 64bit),processor,Harddisk,RAM
with regards,
eswar.

Hello,
O/s      - All 64bits now a days.
CPU    - PIV or Dual core also.
RAM    - 3GB
H/Disk - 300 to 400 GB.
Above all are minimum recommended.
If u are able to arrage more , I/O ie performance will be good.
That's it.
Note: Points always encourage me to reply !!

Hardware requirement for Oracle Universal Content Management

Hi Experts,
What are the Hardware requirements for Oracle Universal Content Management ?
Regards
Nasir

does this help?
Oracle WebLogic Server 11g (10.3.3) System Requirements
Oracle WebLogic Server supports a number of platforms including:
– Linux
– Sun Solaris
– HP-UX
– Windows 2000, 2003 Server, XP
• Processor:
– At least one 1 GHz CPU is recommended.
– Intel and UNIX processors are supported.
• Hard disk drive:
– A full installation requires approximately 2 GB of disk space.
– The Linux value for file descriptors must be 4096 or greater.
– Samples are optional (download from OTN).
• Memory:
– A minimum of 2 GB RAM is recommended for WebLogic
Server.
– Consider the number of simultaneous users and sessions.
– Consider in-memory programs, such as Coherence.
System Requirements
The following are some of the basic system requirements for Oracle WebLogic Server 10.3.3:
• The Oracle WebLogic Server installer requires a Java Runtime Environment (JRE) to run.
Oracle WebLogic Server is certified with JDK6.0. As part of the installation, it gives the option
to install the JRockit JDK 6.0 version. As part of postinstallation, prefix the bin directory of
the JDK to the PATH environment variable.
• The Oracle WebLogic Server installer requires a temporary location in which to unpack the
files. Typically, the installer requires approximately 2.5 times the amount of temporary space
that is required by the installed files.
Note: In this release of WebLogic Server, users can choose which components of WebLogic Server
they use. Specifically, this release allows users to choose whether the Enterprise JavaBeans (EJB),
Java Message Service (JMS), and J2CA services are started when WebLogic Server is started. The
benefit of excluding some services is reduced memory footprint and reduced startup time.

Hardware requirement for Fusion Applications HCM installation

Hi Team,
I want to install fusion applications for HCM.
Can any one suggest the minimum hardware requirement for installation.
Please help me with any documents.
Thanks,
Chandra

Dear Chandra,
Please note that Fusion Applications installation involves following components.
1. Oracle Identity and Access Management components (Middleware infrastructure)
2. Oracle Database for IDM
3. Oracle Database for Fusion Apps
4. Fusion Applications Domains (includes Admin and managed servers for Fusion Applications)
I have posted a guide on installing Fusion applications on 2 node setup and if you have sufficient hardware to host 2 VMs then it can be done on single server as well.
http://www.oratraining.com/blog/2013/03/oracle-fusion-applications-installation-step-by-step-guide-11-1-6/
This will explain the 2 node architecture which I have prepared.
http://www.oratraining.com/blog/2013/03/fusion-applications-architecture-for-2-node-setup/
The minimum memory requirement changes if you select more products since in Fusion apps each products have their own domain and if you select more products then there will be more application managed servers (even if you don't select a product family, it will still create some managed weblogic servers based on dependency with selected products)
The minimum memory requirement to host IDM and consolidated DB in 1 node is 10-12 GB
The minimum memory requirement to host Fusion Applications domains on 2nd node is 64 GB (for 1 product family, for all products selected then 128 GB)
Please note that these are "minimum" requirements based on my experience, not as per the documents since what we are talking about is installing for "learning", not for production, where you will host various components in separate nodes.
Thanks
Tushar
www.oratraining.com

Hardware Requirements for ECC 6.0

Hi everyone.
Can anyone tell me the hardware requirements for ECC 6.0 with RAID implementation
OR
Any link where i can find the information.
**i did check in the market place***
Thank you
Kiran Kumar

Hi,
Begin in http://service.sap.com/quicksizing for hardware requirements in SAPS(processing), memory and disk space. Then check in installation guides http://service.sap.com/instguides the best configuration
of the disks in RAID. Basically:
RAID 1 - database server program files
RAID 5 - data files SAP
RAID 1 - transaction log file
Best regards,
Roger Vier

Hardware requirements for SAP ERP 2005 using ECC 6.0

Hello everyone,
i am already new and need information about the min. hardware requirements for a SAP ERP 2k5 System using ECC 6.0 with IDES 7.10.
I read the Master Guides about ERP, but i am not even more clever than before.
The OS is MS Windows 2k3 Server EE.
The last information i had from another one to this configuration is:
1 dual-core cpu (? Ghz)
4-6 GB RAM
300 GB HDD
Does it fit? Can anyone help me out?
Thanks in advance.
Message was edited by:
        Marcel Jahn
Message was edited by:
        Marcel Jahn

Hi,
IDES 7.10?!?
If it's an IDES system you want to set up, HDD space may be the bottleneck. It's sufficient for installation, but you may run out of disk space since note <a href="https://service.sap.com/sap/support/notes/1013391">1013391</a> states
Hardware Requirement
                 MS-SQL ORACLE   MaxDB   DB2 Win/Unix AS/400
DB size (GB):    160     220      220          160       280
Since IDES is for education and training purposes only the rest should be sufficient.
I'm running an ERP 6.0 IDES system (32 bit) on a single core, 3.2 GHz, 4 GB RAM, 250 GB System and 500 GB SAP/DB HDD with pretty good response time.
Peter
Points always appreciated

Hardware requirement for server

Similar Messages

Maybe you are looking for