How can I configure and control a non-plug and play VXI card using the NI-controller (NI-VXI/NI-VISA software)?

Defining the slot, logical address and sending data across the card bus are the main operations I would like to perform. The non plug&play card is a VXI send & receive slave card. Low-level programming is probably required. Has anyone tried this before? If so I would be so grateful if you could share your experiences or refer me to someone who has.
Thank you for your time and help,
Nandeesh

VXI cards are, by specification, plug and play, so I'm not exactly sure what you mean by a "non plug&play card." I'm guessing that the card is effectively a VME card. In this case, you can just add the VME device in the proper configuration utility. Here is a link to a document on our website about configuring VME cards (http://ni.com/support/vxi/vmeinfo.pdf).
You should easily be able set the slot, pseudo Logical Address and memory space. Once configured, you should be able to write to registers using NI-VISA commands (viIn, viOut, and viMove). These high level commands are included in the highreg.c example which shipped with your NI-VISA software (installed in vxipnp directory).
I hope this helps.
Trey Hamilton
National Instruments
Applications Enginee
ring
http://www.ni.com/support

Similar Messages

How can I mute and unmute my Mic using the button ...

I have a button on my mic that is a play/pause button. It works fine when playing music on my phone. Can I use this button to mute and unmute my mic when using skype? The Volume up and down buttons already work. Thanks

That cable set up you have is probably not going to work. The iOS devices seem a little sensitive to having the right connector for the right job. I have the USB connector (and the HDMI one too) which is in 2 parts: mini USB link and SD. My older Nikon D70s does not use SD cards, so I use the cable. When connected any images on the card (in the camera) are displayed in the built-in Photo app in an Imports album. Just touch the Import button and all are brought in. I use RAW and have found that the RAW images are transferred to the computer (MacBook Pro + Aperture) when I get home. A comparison (I kept the images on the card and imported from that too) shows that the resolution/size is identical. As an additional note as you mentioned this, video clips work the same.
With all the connectors, I carry a small bag for the devices I work with.

How can I open and close private browsing using an IPAD mini in IOS 7?

How can I open and close private browsing using an iPad mini in ios7?

Tap the '+' to the right of the URL field to open a new tab, and at the bottom left of the screen there should be a 'Private' button - tap that and you can then go to the site that you want to go to

How can I view and download iprocurement history for the past 1 year in Oracle?

Hi,
I'm presently using Oracle 12, how can i view and download iprocurement history for the past 1 year or longer in Oracle? The purpose is to view approval of claims etc..
if not, where can i retrieve this information in oracle?
Appreciate your urgent assistance.
Best Regards, Michael

Sign into your Account > Click on your account name > Click on Account > Purchase History
iTunes Store & Mac App Store: Seeing your purchase history and order numbers - http://support.apple.com/kb/HT2727
Direct link - https://phobos.apple.com/WebObjects/MZFinance.woa/wa/purchaseHistory

HT5731 i have accidentally purchsed the same episode twice. how can I delete and get a refund for the erroneous purchase?

i have accidentally purchsed the same episode twice. how can I delete and get a refund for the erroneous purchase?

You can try the 'report a problem' link to contact iTunes Support and see if they will refund or credit you for the second purchase : http://reportaproblem.apple.com
If the 'report a problem' link doesn't work then you can try contacting iTunes Support via this page : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page

How can I create accurate decimal dimensions when creating a new document or using the art board in Illustrator CS6? When I type in a number with a decimal, it automatically rounds the number up.

How can I create accurate decimal dimensions when creating a new document or using the art board in Illustrator CS6? When I type in a number with a decimal, it automatically rounds the number up.

For my part you are welcome, sdowers.
Unfortunately, the uncertainty arising from the rounding has been up several times here in this forum.
I just came to remember a warning that needs to be given:
The rounding of the representation of a numerical value may be harmless in itself, but if you use it for any operation that changes the value, such as multiplication or whatever, things will go wrong because the operation will be made on the basis of the rounded value instead of the true value. So, as in your first case in post #2, 39.625 rounded to 39.63 will become 79.26 instead of 79.25.

How can we configure or control records go into single idoc thru BODS?

Hi,
Our case is -
IDOC format has three segment. Each segments has child nodes -
1. CONTROL SEGMENT - This is required only once per idoc.
child1
child2
2. SEGMENT1 - sinlge source record to be broken into two segments.
child1
child2
3. SEGMENT2 - sinlge source record to be broken into two segments.
child1
child2
we have a single source (lest say having 100 records).
In the current design which does generates IDOCS but as many as the no of records in source. Currently we use a row generation transform as dummy (with row count as 1) to pass to the IDOC parent nodes's from clause to escape the error - invalid input to the parent nodes.
Child nodes are either mapped to the source table or are null.
Question - How can we configure this in a way that we control how many records go into single idoc. Ex - lets say 50 per idoc so only 2 idoc should be created if 100 records are there.

HI,
this sounds to me like Data Services. If so I would suggest to post this into the Data Service forum.
regards
Ingo HIlgefort

How can my wife and I add photo to the same photo stream with different apple ID's?

My Wife and I are having baby and we would like to both be able to add photos to her shared "baby" photostream. We have different apple ID's. Is this possible and how can we do it?
Thanks!

No, you would have to share the same apple id. FAQ photostream http://support.apple.com/kb/HT4486
You could do this have your wife import the pics to the computer http://support.apple.com/kb/HT4083 , then you can sync those pics to your phone using itunes.
Or use dropbox, there should be an app.

In my Thunderbd 24.4.0-Windows7-how can I copy and save to DVD all the emails? Unlike in previous Thundrbd they no longer come up in Defaults under Mail.

In my win XP, after Profiles to Default with all those numbers, then Mail, up came Local Folders which contained all the current emails, which were then easily open-able and save-able.
How can I now do the same with my newer thunderbird on my windows 7?
Thank you

Thank you - I now can find the Mail folder, and then only when I select : pop3.virginmedia-1.com (my server) from it's 3 choices, does it show all my email folders. They are all in 2 versions. Those ending .msf I cannot open as they are "not a valid Win 32 application". The others with a little page icon, do all open - in Wordpad or Libreoffice, but the messages are almost totally lost amongst dozens of complex data pages before and after each little actual message! How can I open and see just the actual email messages without all the vast other data, so that I can then save them to a DVD?
Thank you,
Ted

How can I configure a third party VME board with A24 address space using a VME-MXI-2?

Hi!
We are trying to establish communications to a Galil Motion controller with a VME interface. Galil states that they are using a A24 address scheme with A16 data space for their board.
I am confused how to configure that board in the VME chassis properly.
The base address provided by Galil is 91Fxxx, I am assuming that the lower three nibbles are the registers that I can talk to?!
How do I set the address range under the resource setting for that board?
Also, I noticed in MAX that one board shows up with a slot number unknown, one with slot #0 and this board I have set to slot #1. I assume that the unknown part is for the PCI card that makes up for the 1/2 of the PCI to VME bridge?
The VISA VIs (Register based access) returns either a bus error, an invalid offset specified or data. However, we are completely in the dark when it does return data, since the expected offset we are typing in causes one of the two errors.
Our assumption of the problem is that we do not understand how to properly configure that third party board as a resource. It has also happened that the resource manager is hanging up the PC completely. Not even CTRL-ALT-DEL works and the MXI activity LED on the NI-VME-MXI-2 board stays on during the hand up.
We would appreciate, if somebody could walk us through the configuration process, step-by-step. Specifically, please explain how to setup the base address and how the offsets relate to this on a A24 address scheme. We are completely new to the VME bus interface, so even trivial things may be unkown to us.
We have browsed NI's page and manuals for explanations, however, we could not find any answers to our questions.
We noticed a formula for an A16 board that takes the base address and adds the logical address to it plus 40hex. Do we have to do the same or something similar to the A24 board????
We also came accross an option that would allow the board (NI VME controller) to share its memory with A24 or A32 space? Do we need to enable that? What is the purpose for that?
Best,
Markus Tarin
www.movimed.com - Custom Imaging Solutions
www.movitherm.com - Advanced Thermography Solutions

When I did not get a response here, I had to open a ticket with support. The short answer is that you cannot customize the SAML response when using Azure AD as an IdP.
Response from support:
I discussed the issue with senior engineers to get action plan for this issue. After doing research Senior engineers updated me that we cannot add a custom attribute to the default
SAML response of Azure AD.
Below is the link to get the list of available attributes
https://msdn.microsoft.com/en-us/library/azure/dn195587.aspx
As default SAML response from Azure AD , we have email address of the user sent out as attribute value for the Attribute " NAME ".
They suggested me to configure the application we are trying to integrate with Azure AD in such a way that it transforms the Attribute " NAME " into " EMAIL
This was not particularly helpful in my case as I did not have any control over the 3rd party which specifically documented that they would not extract the email address from the name attribute.
Cheers,
Jeff

HT5312 I forgot my security QA. How can I reset and it up again? The problem is: when I log in the "Password & Security" there is no "Send reset security info email to ..." How can I do in this case? Thanks in advance for prompt help

Hello,
I forgot my security answer fro the security questions. I want to reset it and get new one, but therer is no sign: "Send reset info email to ...".
How can I do?
Thanks in advance
tolia9960

Didn't the link to contact the iTunes Store staff in the 'Additional Information' section of that article work for you? If you don't already have a valid rescue email address, only Apple itself can assist with recovering lost answers.
(89599)

How can I find and disable Page Down in the Keyboard Shortcuts menu?

I often accidentally hit Page Down because it's right beside my arrow keys. It seems to switch to the next symbol in the library which is something I never under any circumstances would want to do. How do I disable this incredibly annoying keyboard shortcut? I can't find it anywhere in the unsearchable rat's nest that is the Keyboard Shortcut menu.

Aha, thank you for drawing my attention to the export html button, it does make it possible to search those keyboard shortcuts.
In my case, View -> Go to -> Next was set to nothing. More oddly, the words "Page Down" don't appear anywhere at all in the generated file, and when I set another random command (Zoom In) to use Page Down it didn't warn of a conflict. Hitting page down zoomed in instead of switching me to another symbol, and when I cleared the shortcut from zoom in it went back to swapping between symbols. I guess I'll have to set something benign to use the page down key.
Bizarre. I guess this must be a bug in CS6?

Elements 11 vs 13: how can I add a new place tag to my PSE13 database without using the wretched and totally inadequate map technology that Elements 13 wants to impose.

HI,
I have recently installed Elements 13 having used Elements 11.0 successfully to build a database of 30,000 plus images indexed by place, people, and photo date. Elements 11 allowed me to add new places which are meaningful to me but which are a complete mystery to the mapping technology of Elements 13. For example some years ago I lived in London in a road called Argyle Road. In elements 11 I could enter the place tag as Argyle Road. In Elements 13 I am required to locate Argyle Road on the map, but the map presupposes that the Argyle Road I am referring to is in Ealing in West London. It is not!
I now live in a place called Broadsands but the Elements 13 Map places this 0.5 miles away from what I would describe as Broadsands.
So the question: how can I add a new place tag to my database without using the wretched and totally inadequate map technology that Elements 13 wants to impose.

Thank you for your quick response, BalusC. I really appreciate your answer.
Yes, you are right. If I manually code the same amount of those components in the JSF pages instead of generating them dynamically, the server will still run out of memory. That is to say, JSF pages might not accommodate a great deal of concurrent visiting. If I upgrade the server to just allow 1,000 teachers making their own test papers at the same time, but when over 2,000 students take the same questionnaire simultaneously, the server will need another upgrading. So I have to do what you have told me, using JS+DOM instead of upgrading the server endlessly.
Best Regards, Ailsa

How can i put and see my movies in the ipad2?

I have movies of my own that i didn´t get through itunes and i cannot put them on the ipad, nor on itunes, just like the music i already have.
How can i do that?
i was told it was possible, that is why i bought it. If it is not possible, then the ipad is not interesting for me.
If it is possible, could someone help me on this?
Thank you.

Unlike the songs, you have to convert the movies to a format that the iPad can read - Handbrake is one program that will do it for you, but there are others.
Be aware that if you are talking about taking DVD's and putting them onto the iPad, that would require stripping the copyright encoding off it, which is illegal in many countries (even for legally purchased DVD's), and discussion of how to do this is not permitted on this forum.

How can a IMac and a ipad comunicate through the cameras

I would like to connect with a iPad and use the camera in my iMac and the ipad . How can this be done?

Sorry, but it doesn't work that way.
Hope this helps

How can I configure and control a non-plug and play VXI card using the NI-controller (NI-VXI/NI-VISA software)?

Similar Messages

Maybe you are looking for