How can I Loose the Heat or Fan Control in G4 Tower?

I have a G4 FW 800 Tower that is running hotter with 10.5.x and knowing that heat kills hardware, I'd like to use the existing internal fans that do a great job when they fire up, to cool it down as I have seen them do. I have a temperature monitor app that uses the internal sensors to guage heat and have seen a dynamic change possible. I have a Dual PCI Bay fan that helps, but the biggest difference is when the 6 Speed Internal Fans kick in at Start, Restart, Single User Mode, Safe Mode even for a few minutes I have seen a 13-20 degree drop in temperature. So if I could get these fans to ramp up above level 1-2 that they do during normal operation the CPU, Motherboard, Optical and Hard Drives could be nicely cooled. And I don't mind the sound because at level 6 it's not all that bad. Plus if there are internal heat sensors, why are there nothing for them to really do. Like fire the fan up to level 4-5-6 when this start getting hot. OR as I have seen conspiracy theorists post that this is Apples way to limit the life of the hardware? Anyway. . .
I know that there are applications for laptops, I have installed many, that allow you to control their fans. Where is one for desktop machines? Are there any? If not, why? I would imagine that one would want the same control and benefits from it since Apple seems to have not done anything here. Although I would loose my little space heater that is serving me very well this cold Winter. I'd rather have cold hardware.
So . . . .
Any information will be greatly appreciated.
Thanks . . .
. . . tg

Thanks for the reply, but this firmware update is for the Dual Boot "Wind Tunnel" models where the fans would race when running OS9. I have a FW800 that is not a Dual Boot and thank God not a "Wind Tunnel", matter of fact this replaced a WT and is was next generation and last of the G4's.
I have found a couple of utilities that are for the Intel's with SMC, but it looks as though my model, sure 'nuf, does not have the architecture to support this type of control. With the way the fans run on their own there has to be something there that controls them that can be tapped into. I can only pray someone has tapped it! Fingers Crossed.

Similar Messages

How can i use the ACL file to control the access from the other website?

Hello all~
My Sun one is 6.1 sp3 on Windows 2003 SE, and I am try to use the ACL file to control the access.
My ACL file is below:
version 3.0;
acl "path=my_path_on_HD";
deny absolute (all)
(user = "anyone") and
(dns = "*.my_site.com");
deny absolute (all)
(user = "anyone") and
(dns = "*.other_site.net");
Once I add the "deny", anyone include my site is decline for vist the path specify in the ACL file. But if remove the "deny", everyone include other one's website can access the file.
Can anybody tell me how to make it work?

I think you've misunderstood what the dns attribute is for. The dns attribute returns the hostname of the client accessing your website, not the hostname of the website that linked to your website.
For example, when someone using the Comcast ISP goes to a malicious website at example.com that loads images from your website at www.amigoo.net, the dns attribute will be something like "c-1-2-3-4.ca.comcast.net", not "example.com". ACLs are used for authentication and authorization of clients (not the websites those clients chose to visit), and they don't provide the functionality you're looking for.
If I understand correctly, you want to prevent websites other than amigoo.net from linking to files in your d:/webserver/imat/pics_upload directory. You can achieve this adding the following lines to your obj.conf configuration file:
<Object ppath="d:/webserver/imat/pics_upload/*">
<Client referer="*~*amigoo.net">
PathCheck fn="deny-existence"
</Client>
</Object>

How can i find the appreciate XI content: Control System - SAP ERP?

Hi all,
I'm try to find an XI Content for Control System (Insite is our Control System) - SAP ERP. I don't know if it exist an XI Content Control System (Insite) - SAP ERP? If this XI Content is exist, how can i find it and the document about this XI Content?
If anyone do or did an integration scenario between Control System - SAP ERP and know the appreciate XI Content for this scenario, could you please help me?
Thanks a lot in advance,
Vinh Vo

hi
check whether the content is available in SMP
https://service.sap.com/swdc -> Content
The XI content details can be found here.
rgds,
Arun

How can I change the description of a control Icon with property nodes?

hi
I want to change the description of a control Icon and use for this the property nodes, but I don't know how. Who can help me?
labprog

If you're referring to the control's name on the screen, you can't change the label while the VI is running because it's part of the control's definition. Instead, make the label invisible and the caption visible and use the property Caption.
If this doesn't help, elaborate more on what it is you need.
Try to take over the world!

How can I change the size of table control in table maintenance re-gen?

Hello Experts,
I hv created a maintenance view and after generated table maintenance view for it.
now it adjusts the size of table control in table maintenance generation.
I want to change the size (width) of table control and again re-generate the table maintenance.
But when re-generation occurs, table control size is set to initial.
why it is happening? and wt to do to solve this issue? any user exit?
I need the changed size of table control even if its re-generated.
Regards,
R.Hanks

Hello Ronny,
Goto SM30, Enter your table name for which you have maintained your table maintainence generator .
When the maintainence screen appears for your table name , Goto System->Status->Screen Program name.
Copy that program name from there.
Open that module program through SE80,this is the program name of your SM30 screen which appears when we enter our table name in SM30 transaction.
In SE80,click the layout of the module program name you have entered there.
Its layout will display you the table control(of SM30) present to enter your your enteries.
In the change mode you can change its size , savee it and activate that program.
Now goto to SM30 again and enter your table name, it will show you the changed size of the table control used to take the enteries.
Note:This changed size is only for your table name and it will remain of its previous size for other table enteries.
Hope it helps you.
Thanks Mansi

How can I save the plot on Graph control to disk like the plot on Picture.vi ?

Dear all
I have a question about saving the plot on graph control.
In Labview,there is two way to make a plot, using graph control (eg. waveform control ,wavechart control) and Picture.vi (eg. plot XY vi and plot waveform VI ) ,
but for Picture.VI there is some control for saving them to disk (eg. write jpeg file.vi or write bmp file.vi )
My question is that may I save the plot display in graph control to disk using some vi like saving Picture to disk.
I only know we only can right clicking and export implified image to save the plot on graphic plot?
What want is save the plot on graphic control without interface and save to disk directly?
many thanks!

RIght-click on your graph and select:
Create...Invoke Node and select method "export image". Wire the desired inputs and place it inside a case structure to be activated by e.g. a button.
LabVIEW Champion . Do more with less code and in less time .

How can I find the coordinates of individual controls inside a custom control?

I have a custom control that contains 44 smaller custom controls.
I can get the coordinates of the 44 embedded custom controls by getting the controls[] property of the main control, but I cannot find a way of getting the coordinates of the controls inside each of these smaller custom controls.
Is there a way of getting at the coordinates of custom controls that are nested several layers deep?
Erik.

For future reference and for any LabVIEW users who have older versions here are the Front Panel displays before running the VI along with the Wiring Diagram with each of the four cases for handling the various types of ClassIDs that can contain child controls. X1, X@, Y1, and Y2 are the coordinates of the top left and bottom right corners of each control. These coordinates can then be used to determine which control the mouse is pointing at.
In my own project I did further evaluation to eliminate all parent controls (controls that contain other controls) and passed along only the controls that were end-nodes (controls that contain no other controls). Also, the control's refnum was stored for later use.
The bottom picture shows the data gathered during the execution of this VI.
Thanks again, Mike!

How can I connect the TestStand 30 UI controls to a remote instance?

I have been playing with the TestStand 30 UI controls (which I love), and I can't see a way to connect them to a remote instance of the TestStand engine. My observation has been that they always connect to the local instance of the Application manager.
Just to be clear, I want to run TestStand on computer A, then create some UI controls (sequence view file manager, sequence view, some combo boxes, etc) on computer B, and have them connect to the engine on computer A.
I noticed that you can set the sequence file context on the SequenceFileViewMgr object, but not the applicaiton manager context (the property is read only). When I try to set the ISequenceFileViewMgr:equenceFile property to a remote inst
ance of a sequence file object, the control doesn't seem to connect. I can only connect to sequence file objects that have been created locally through the application manager.
Thanks,
Aaron Stibich

The controls don't support that scenario, and if they did, I would expect that the resulting tracing performance would be unacceptable. It is an interesting idea though and it would be nice to try it without tracing to see if it was fast and robust enough to be useful. I'd need to investigate whether the controls use any non-remotable internal APIs before attempting to enable this. I'll add this idea to our suggestion list.
I don't know if it is appropriate for your use case, but if you can instead connect to the remote machine via RemoteDesktop, you should be able to remotely run an OI application with decent performance.

How can I view the logs in Parental Controls?

I'm trying to monitor my children's internet use and iMessages on our laptop and the logs show there is activity. However, I cannot see anything when I click on the actual log entries. Is there something I'm missing? I'm having this issue with both internet and iMessage. Whenever I click on the iMessage log entry, a window pops up from iMessage as if I'm going to start a new conversation. Very strange.

If your children are comp savy, it's possible that they have erased the logs. You should set up parental control. This way you can control all internet & comp usage. Your children will not be able to erase or get into anything to erase if you do not make that option available.

How can I increment the label of a control panel?

I would like to place data into several controls in one panel. These controls are labeled CTR_0 through CTR_63 . I would like to use a function like:
int value[64]
for (x=0; x<64; x++)
SetCtrlValue (panelHandle, PANEL_CTR_x, value[x]);
Anyone have an idea short of setting each one on a seperate line?
Any help would be appreciated.

When I have a larger amount of equal controls (e.g. channels), I usually
place only one of the controls into the .uir file, and then build the
remaining controls programmatically in a loop, using the DuplicateCtrl()
function. The advantages are, that I can set (and change) the control
attributes (position, size, label, colors, callbackfunction ... ) only at
one place in the .uir file, and besides I can store the control ids in an
array from where the controls can be easily accessed.
digOutPanel = LoadPanel (0, "DigitalPanel.uir", DIGO_PANEL);
/* buttons for digital outputs */
GetCtrlAttribute (digOutPanel, DIGO_PANEL_SETOUT, ATTR_WIDTH, &width);
GetCtrlAttribute (digOutPanel, DIGO_PANEL_SETOUT, ATTR_LEFT, &left);
digOutSet[0]=DIGO_PANEL_SETOUT;
for(
i = 1; i < MAX_DO; i++)
sprintf(buf, "%02d", i);
digOutSet[i] = DuplicateCtrl (digOutPanel, DIGO_PANEL_SETOUT,
digOutPanel, buf, VAL_KEEP_SAME_POSITION, left + (width+2)*i);
Regards,
Manfred
zener schrieb in im Newsbeitrag:
[email protected]..
> I would like to place data into several controls in one panel. These
> controls are labeled CTR_0 through CTR_63 . I would like to use a
> function like:
>
> int value[64]
>
> for (x=0; x<64; x++)
> SetCtrlValue (panelHandle, PANEL_CTR_x, value[x]);
>
> Anyone have an idea short of setting each one on a seperate line?
>
> Any help would be appreciated.

How can i change the color of table control' lines?

Such as the subject. Thanks in advance!

Hi,
Please check,
TABLE CONTROL LINES COLOR CHANGE
color rows in table control
Regards,
Hema.
Reward points if it is useful.

How can i use the same front panel graph in more than one events in an event structure?

i want to display the signals from my sensorDAQ in a graph.but i have more than one event in the event structure to acquire the signal and display it in the graph.the first event is to acquire the threshold signals and its displayed in the graph as a feedback.after the first event is executed, i will call the second event,where the further signals are acuired and compared with the threshold signals from the event 1.my question is how can i use the same front panel control in more than two events in the event structure?please answer me i'm stuck.
Solved!
Go to Solution.

Hi,
I have attached here an example of doing the same using shift registers and local variables. Take a look. Shift register is always a better option than local variables.
Regards,
Nitzz
(Give kudos to good answers, Mark it as a solution if your problem is Solved)
Attachments:
Graph and shift registers.vi ‏12 KB
graph and local variables.vi ‏12 KB

How can i get the content of JTextArea with out loosing Indentation.

I am developing one mail sending application. I am getting mailid , from address, mail body from one Swing. In one JTextArea i am typing i have typed some matter. When i call the content of JTextArea using
jtx.getText() method, i am getting all the content as one paragraph. That means there is no indentation which was there in TextArea.
Please provide me some solution how can i get the content of JTextArea wiht out loosing indentation.

And it was you who asked the question!

How can i get the max rpm from cpu fan??

how can i get the max rpm from my cpu cooler regarding that i don't have a speed controller attached to the cpu fan ,,, ?? please make things clear for me
thanks

if you have not reduced it by using a speed controller either hardware or software or by the 7v mod its already going as fast as it will at 12 v dc you cannot speed it up only slow it down
need more air get a different cooler/fan

I have all my music on an external media drive that has crashed. How can I get the music of my ipod touch back onto the comupter without loosing the music when it syncs?

I have all my music on an external media drive that has crashed. How can I get the music of my ipod touch back onto the comupter without loosing the music when it syncs. in order to start rebuilding my music collection?

You should be able to recover the media with the tips in this post from forum regular Zevoneer but I'm not sure what the implications are for your application settings. You can probably transfer your purchases into a newly authorised library, backup the device, recover any other media using third party tools, then restore the device from the backup. That should switch the assocation of the device to the new library but it is not something I've personally tested.
When you get it all working, make a backup!
tt2

How can I Loose the Heat or Fan Control in G4 Tower?

Similar Messages

Maybe you are looking for