How do i get the data present in the selected row at run time in Multicolumn list box?

Hi,
I am using multicolumn list box with three columns and i am having OK button.
If the user selects particular row and then press ok then that row datas(that 3 values) has to get update in the file.
Can u tell me how to get that selected row values alone and also how to append the list box value at run time?
Thanks
Meenatchi

You can simply use the Value property of the MLBox to get the row selected & wire it to the Delete from array function with the Itemnames of the MLBox as the Input & Output of the Delate from array function.
See the attached VI.
- Partha
LabVIEW - Wires that catch bugs!
Attachments:
Dbl-click Row to get Data & Delete.vi ‏41 KB

Similar Messages

How To... Change the Data Type for a SELECT-OPTIONS at run time.

Hello,
I am trying to restrict the values available for entry into a SELECT-OPTIONS at run time depending on user input.
The logic is as follows. The user has two input fields. A PARAMETER field which has the type RSDIOBJNM and allows them to choose an InfoObject. And the user has a SELECT-OPTIONS field to allow them to select the Characteristic values for that InfoObject.
I would like the following example to be possible:
The user enters 0MATERIAL into the PARAMETER. When the user clicks on the SELECT-OPTIONS control code will derive a list of possible options the user can enter in the SELECT-OPTIONS. In this case only values found in the master data or at least no values greater than 18 characters.
I have looked at the following function module SELECT_OPTIONS_RESTRICT and this do not appear to be helpful as they only restrict on the signs allowed for the values (unless I misunderstand, it is a complex function module!).
The code I have so far is (thus the user enters a InfoObject into p_char1 and the select options so_char1 should only accept active values of that InfoObject):
declaration of variables for user interface
DATA c_char(32) TYPE c.
declaration of count variable
DATA i_count TYPE i.
declaration of user interface
SELECTION-SCREEN BEGIN OF BLOCK a1 WITH FRAME TITLE text-001.
    PARAMETERS: p_ipack TYPE RSLOGDPID.
SELECTION-SCREEN END OF BLOCK a1.
SELECTION-SCREEN BEGIN OF BLOCK b1 WITH FRAME TITLE text-002.
    PARAMETERS: p_char1 TYPE RSDIOBJNM.
    SELECT-OPTIONS: so_char1 for c_char NO INTERVALS.
    PARAMETERS: p_char2 TYPE RSDIOBJNM.
    SELECT-OPTIONS: so_char2 for c_char NO INTERVALS.
    PARAMETERS: p_char3 TYPE RSDIOBJNM.
    SELECT-OPTIONS: so_char3 for c_char NO INTERVALS.
SELECTION-SCREEN END OF BLOCK b1.
Is what I am trying to do possible???
Thanks for any help. Ross.

You really want to restrict possible values of a select-option based on another field, not change the length of type of the select-option field, right?
Here is what you do: Code a custom F4 value help for the select-option at event AT SELECTION-SCREEN ON VALUE REQUEST FOR.. The first thing you do here is read the value of the parameter field (p_ipack in your example). You can use function module DYNP_VALUES_READ. Based on this value, you can propose values for the select-option fields. Note that the use can still enter whatever s(he) wishes in to the select-option field without pressing F4. In this case, you will have to code some input validations taking into account the value in the p_ipack field.

How to save the data present in the description box?

HI friends,
I have got a requirement where i am having one description box (custom_container) in one screen and the line length is 250. Code is like this...
DATA: CUSTOM_CONTAINER TYPE REF TO CL_GUI_CUSTOM_CONTAINER,
EDITOR TYPE REF TO CL_GUI_TEXTEDIT,
REPID LIKE SY-REPID.
CONSTANTS: LINE_LENGTH TYPE I VALUE 250.
MODULE STATUS_101 OUTPUT........
My description box is working fine.....
here i want to store the data entered in the description box(text box) when i press SAVE.
Can any one provide me the solution.

Hi,
Since you are using the class CL_GUI_TEXTEDIT, you can call its' method GET_TEXT_AS_R3TABLE to save the text in internal table.
If you wan ease the work of creating Z-Table to store them, you may use FM 'SAVE_TEXT':
SAPscript: Save text
The function module writes a text module to the text file or text memory, depending on the specific text object.
The module can be used to change existing texts and to create new texts. If it is clear that it is a new text, this can be specified via the parameter INSERT. The result is better performance as a test read is not performed.
Parameters
CLIENT
HEADER
INSERT
SAVEMODE_DIRECT
OWNER_SPECIFIED
LOCAL_CAT
FUNCTION
NEWHEADER
LINES
Exceptions
ID
LANGUAGE
NAME
OBJECT
Function Group
STXD
Hope this helps you.
Thanks,
Anfernee

How do I get my data back on the phone after upgrade?

Say I'm replacing my phone with a 3GS, how does iTunes tie the data it has to the phone, is it by the phone # on the SIM card?
I want to make sure all my data, apps etc. gets back on the phone, what process do I need to follow?

All iTunes content they you have selected to be transferred to your existing iPhone - music/video/podcasts including 3rd party apps remain in your iTunes library on your computer. Photos transferred to your existing iPhone via the iTunes sync process also remain on your computer.
If you are syncing contact info and calendar events with the Address Book and iCal on your Mac, this data also remains on your computer.
You can sync multiple iPods and/or iPhones with the same iTunes library and iTunes account with each device having its own sync settings.
When you connect a new iPhone to iTunes on your computer, you will be prompted to transfer the backup for another iPhone that has been synced with iTunes. After the backup for your existing iPhone is transferred to your new iPhone, this must be followed by a sync to transfer your selected iTunes content including 3rd party apps and any photos on your computer selected to be transferred to your iPhone. You select sync contacts with the Address Book and calendar events with iCal under the Info tab for your new iPhone sync preferences and this data will be transferred to your new iPhone.

How do I get game data back on the iPad after being sent a replacement?

I took my iPad into a shop for repair and they replaced it. Before I took it I backed it up to iTunes. When I got my replacement I synced my iPad with iTunes and got all my apps back. Only problem is I've lost all my game data. My achievements are on game centre. How do I get the game data back? Also I bought extra levels on a game and they have disappeared to? Can anyone help?

You should have restored from the backup before you synced the iPad. If iTunes created a new backup when you synced, the old backup may have been overwritten and the data may be gone.
Without connecting the iPad to your computer, launch iTunes and go to Edit>Preferences>Devices. Do you see a backup in that window from the day that you backed up the iPad before you sent it out to be replaced? If you do have a backup from that days, you can try restoring from that backup. While you are still in that window, click on the box that says - prevent iPods, iPhones .... From syncing automatically. Click OK. Quit iTunes.
Connect the iPad to your computer and launch iTunes, right click on the iPad under devices and select Restore From Backup. Select that backup from the window that pops up and restore from it. Then sync with iTunes.
You can turn Auto sync back on in the prefers when you are done.

Is the iCloud a backup tool for your computer? How do I get my data back -- off the iCloud?

Is the iCloud a backup tool for your computer? ---- Apple care suggested using iCloud for a backup to my documents. I do not have an iphone, ipad or laptop. Just an iMac. Nothing to share the data with.
Now I am unable to access some of my documents on my computer and saving documents is cumbersome because it always wants to save it in iCloud, not my computer. The documents I am unable to open are my old MS-Word. One is a macro enabled word doc. I am using os x mountain lion.
After over an hour chat with apple care, the issue is not resolved. I did not have more time to resolve the issue today and it will be continued next week. Per apple care, I do not have any documents in the iCloud however I am almost at the free capacity with contacts and documents.
My question is -- If I purchase backup from a clould provider - other than apple, back up my files in documents in their cloud (make sure I can open them) and then delete the link to iCloud. Would I preserve my data? Has anyone tried this? I am open to suggestions.
Thanks,
Phyllis

Is the iCloud a backup tool for your computer? ---- Apple care suggested using iCloud for a backup to my documents.
Not really. You can store "Documents in the Cloud" but this applies only to documents created by Pages, Numbers, Preview, Keynote, and Microsoft Office documents created on your computer stored in iCloud's "iWork". Within that limited purpose, iCloud works very well.
My question is -- If I purchase backup from a clould provider - other than apple, back up my files in documents in their cloud (make sure I can open them) and then delete the link to iCloud. Would I preserve my data?
I'm not quite sure I understand what you mean by "purchase backup from a cloud provider" but if you're considering a service such as Carbonite, I don't advocate any of them. To back up your Mac, use your own backup device - Time Capsule or an external hard disk. It's inexpensive and reliable: two elements essential for a backup strategy, that no subscription service can offer.

How do I get live data from a subvi while it is running ?

Hi.
I'm finishing up my little application, and one of the things I cant figure out to get to work is getting live data from a subvi and displaying it on my main vi's front panel.
In my subvi I am sending about 10 commands to the serial port, each time updating a local variable that writes value to a progress indicator. I would like to get that indicator displayed on my main vi so I can see the progress of my subvi.
Currently I have just linked the progress indicator on the sub to a terminal, and connected that to my main vi, but, that only updates when the sub finishes its mission. Is there a way to update the main while the sub is active ?
Any ideas appreciated !
/Brian

In your VI Prg_all_sub, you are actually only writing out the progress bar once to the contol reference. Once the code to the top has executed, it will never execute again although you continue to write values to the local variable PP throughout the program.
The quickest fix would be to put that code at the top in a loop with a small time delay function. That way it continues to execute every time a new value gets written to the local variable. You would have to use a local variable stop button to stop hat loop wonce your string of VISA reads and writes executes. Also make sure to reset that stop boolean to false once the loop ends so that the loop will execute properly the next time this sub VI is called.
Other recommendations for cleaning up the programming is to use arrays or bundle values into clusters that you pass into and out of subVI's. Prg_all_sub and MPS setup loader have numerous wires going into and out of the sub-VI's. Bundling these together would simplify the wiring quite a bit.
Note also that in a lot of places you send in a wire to an indicator and branch it off to a local variable of the same indicator. That is redundant. Sending the wire to the local variable does the same thing as sending the wire to the indicator. Try to use wires instead of local variables as much as possible. For instance, near the top you send the output of the VISA resource name control back into a local variable of itself, (not necessary) then use a local variable numerous times in the case structure below. Just wire the name into the case structure border, and maintain the value through all of the loops using a shift register. This will eliminate dozens of copies of the VISA resource name variable.
In several places you concatenate a carriage return character to a string constant. Just put a "\r" at the end of the string constant when it is shown in \ display. Then you can eliminate the concatenation.
I hope this helps you get your progress bar working and help simplify the code for you.
Message Edited by Ravens Fan on 08-13-2007 09:34 AM

Based on the input parameter can OBIEE select table at run time

For e.g if we select monthly from the drop down then the same report must fetch data from monthly report
and at the same time if a persons selects daily then the same reprot must fetch data from daily table.

Let's assign a presentation variable to the drop down values i.e. var_Status
Now in functionality of the column that you want to change it's functionality dynamically depends on your selection... write this formula
case when '@{var_Status}' = 'Daily' then Table1.Col1 else Table2.col2 end
Because of this.. we can't have dynamic column heading for this column.
One more approach is: Same Presentation variable but with Sectional Guided navigation properties.
see here: http://oraclebizint.wordpress.com/2008/01/17/oracle-bi-101332-selecting-reports-from-dashboard-prompts-and-guided-navigation-sections/
You have to develop 2 reports for this..
Regards
Kishore Guggilla

How do I get Keynote to present in the same way as Powerpoint in a gotomeeting?

I have transferred a Powerpoint sales presentation to Keynote but when I try to share it on GoToMeeting to do the presentation, it does not show the full screen. How do I make this happen?

I deal with the numeric ordering by padding out the sort fields with leading zeros. iTunes used to sort numbers by value but it seems the code for that got removed at some point and hasn't been replaced. You should be able to use sort values to achieve some consistency between the two views of your media.
See also Grouping tracks into albums.
tt2

My battery died and then when i charged the phone it is asking me to connect to itunes and restore. if i restore how can i get my data back

My iphone battery died and on charging the phone it asked me to connect to itunes and restore the phone.
If i restore the phone how can i get my data back and how can i check when i last backed up my phone

If you have been syncing regularly as the iphone is designed, then you can sync the data back.
Regardless you will have to restore the iphone.

HT1386 I have an older iPhone (3gs) and need to upgrade to a newer phone (4S). I need to get my NOTES, CALENDAR, CONTACTS, PICTURES, etc backed up on iTunes so I can get that data loaded onto the new phone. But not sure how to do that.

I have an older iPhone (3gs) and need to upgrade to a newer phone (4S). I need to get my NOTES, CALENDAR, CONTACTS, PICTURES, etc backed up on iTunes so I can get that data loaded onto the new phone. But not sure how to do that. When I open iTunes it has a button that say "Back Up iPhone", but I'm not sure what that does. When I go into the sync options it say I have another user account and asks me if I want to merge of replace. I'm assuming it's trying to tell me I have an older iTunes Library, but don't know that. Geez, maybe people over 60 shouldn't have iPhones, iTunes just bafles me.

http://manuals.info.apple.com/en_US/iphone_user_guide.pdf

How can I get a date picker or wheel to show up in the form to make filling in a form with a lot of

how can I get a date picker or wheel to show up in the form to make filling in a form with a lot of dates more easy?

There is no built-in date picker available for forms created in Acrobat. There are some third-party solutions involving JavaScript (either a large collection of fields or a custom dialog) though. Also, text fields with date formatting will use a wheel type date picker on Android/iOS devices with Adobe Reader.

How to get values/data stored in the database into a list-item.

how to get values/data stored in the database into a list-item.
i tried to make a list item without any values assigned to it...but i got the below error.
FRM-30191: No list items defined for required poplist.
or
FRM-32082: Invalid value for given item type.
List EMPNO
Item: EMPNO
Block: EMP
Form: MODULE5
FRM-30085: Unable to adjust form for output.
then according to some docs, i tried the the following for the trigger
when-new-form-instance
declare
     rg_name varchar2(40) := 'emp_rec';
     status number;
     groupid recordgroup;
     it_id item;
begin
     it_id := Find_Item('empno');
     groupid := create_group_from_query(rg_name, 'select empno from emp');
     status := populate_group(groupid);
     populate_list(it_id, groupid);
end;
but yet didnt work... :(
so how the heck do i get values fetched from the database table into the list item?

for list items you need to values in the record group, one is the shown value and one is the returned value.
Check out the online help for the populate_list built-in.
You'll need something like select ename,ename from emp as the record group query.

When insert my lexar USB flash drive I get the message that the disk was not readable by this computer. It has worked previous to this and I do not want to lose the data by reformatting the drive. How can I reformat this drive and not lose my data?

When insert my lexar USB flash drive I get the message that the disk was not readable by this computer. It has worked previous to this and I do not want to lose the data by reformatting the drive. How can I reformat this drive and not lose my data?

You can't reformat it and not wipe everything on it.
Have you tried a different USB port?
Only other option, back it up on a different computer.

How do I get routing data from the Map App (powered by TomTom) so I can display the point-to-point annotations (turn-by-turn navigation) without leaving my own application.

I have a tableView displaying a list of contacts from a Cloud Database. After selecting a contact, I push to a programmatically created MKMapView. Then I display the initial region (the view) that includes the users current location (starting point) and their selected destination (end point).
Now I want to display annotations (as described in the Location Awareness Programming Guide) that displays polylines which will represent the turn-by-turn navigation IN MY OWN APPLICATION, and not in the Map App currently used in IOS6.
Due to licensing and its becoming depricated in IOS 6, I do not want to get routing data from the Google Maps API. How do I get routing data from the IOS 6 Map App (powered by TomTom) so I can display the point-to-point annotations (turn-by-turn navigation) without leaving my own application?
I checked out Stack Overflow and other forums which basically left me with the impression that this is not possible. I also checked out the TomTom iPhone Mobile SDK User Guide from the TomTom Developer Portal and am still confused. It must be possible to retrieve routes, since the Map App can display turn-by-turn directions. How can I retrieve turn-by-turn data that I may display as a route within my own application?

Thanks Michael. Apologies for the slow reply I was away for a bit (holiday blitz at work and visiting family madness etc.etc.) back now, I set both options you requested to "never " and retried the CMS software with no change.
I do have progress of a sort though, as a test I took a separate test PC and put a clean install of Win7 on and loaded up the CMS software (it worked perfectly) and then took the version of ole32.dll off that machine and put it onto the computer I had built
for her (using Linux) and...
got a new error code. Darn I was so sure I had found a clever solution this time lol.
Anyway now when the CMS fails it gives me a similar error but the offending module is "ntdll.dll" sooo... I tried taking the "working" version of ntdll.dll from the test box and moving it over (making sure to back up the existing ones
first so I could put them back if needed) to her new PC and the PC would not boot.
It seems to want the original versions of a few Dynamic Link Libraries and if I could somehow give it those while not breaking Win7 it should theoretically work seeing as it no longer errors with ole32.dll.
ntdll.dll however seems necessary for Win7 to boot.
So what I am wondering now is:
Is there some way to have both versions of the DLL file in the system32 folder (bypassing the "cannot have two files with the exact same name in the same folder" thing) or rename the original DLL's something else and somehow make the CMS look for
the new named versions so the system has the updated DLL's it needs to boot/run and the CMS has the old ones it wants to run or is there someway to have a self contained install of the CMS, say on a USB flash drive and give it it's own E:/windows/system32/needed
dll's path to the files it needs?
Willing to try any other options or settings you may have come up with as well.
Thanks again for your reply and my apologies for not answering sooner.

How do i get the data present in the selected row at run time in Multicolumn list box?

Similar Messages

Maybe you are looking for