How do you replace a hard drive on a xserve raid

I am running an old xserve (10.3.9) I need to replace one hard drive in my raid set. I have a new hard drive exactly the same as the one I am replacing. Do I have to do anything in raid admin (version 1.2) or once I insert the new hard drive will it just start working and the other drives will start talking and writing data to it? Thanks for any help!

Hi
Slightly confused about what it is you actually have?
Do you mean an XServe like this one here:
http://www.google.co.uk/imgres?q=XServe&num=10&hl=en&tbo=d&biw=1433&bih=856&tbm= isch&tbnid=VXlw7-KP6nEsaM:&imgrefurl=http://inertz.org/2008/01/xserve-an-impress ive-multitude-of-potential-used-server/&docid=HT9gRAJQrNrS8M&imgurl=http://inert z.org/wp-content/uploads/2008/01/xserveg5.jpg&w=600&h=361&ei=9YPQUI6dLeX-4QTwloC 4Dw&zoom=1&iact=rc&dur=639&sig=102214044775849835144&page=1&tbnh=144&tbnw=242&st art=0&ndsp=35&ved=1t:429,r:3,s:0,i:124&tx=152&ty=81
You can't/don't use RAID Admin on an XServe.
Or do you mean an XServe RAID like this one here:
http://www.google.co.uk/imgres?q=XServe&num=10&hl=en&tbo=d&biw=1433&bih=856&tbm= isch&tbnid=-wl73CtlayTBlM:&imgrefurl=http://en.wikipedia.org/wiki/File:Xserve_RA ID.jpg&docid=9pxrypAvxoLK-M&imgurl=http://upload.wikimedia.org/wikipedia/commons /0/06/Xserve_RAID.jpg&w=1296&h=416&ei=9YPQUI6dLeX-4QTwloC4Dw&zoom=1&iact=hc&vpx= 709&vpy=345&dur=119&hovh=127&hovw=397&tx=170&ty=57&sig=102214044775849835144&pag e=1&tbnh=81&tbnw=252&start=0&ndsp=35&ved=1t:429,r:11,s:0,i:148
If it's the above simply remove the drive module and assuming you have a replacement drive module and drive, insert the new drive module. If you only have the drive, release the plastic moulding at the foot of the removed drive module, release the screws, remove the drive and reverse the process to install the new drive. Insert the module and the rebuild should happen immediately and you can use it normally while all this is happening. Depending on how much data you have stored on the unit, performance loss should be minimal. I would monitor the progress using RAID Admin.
As ever try and make sure you have a full and effective back-up handy just in case.
If it's an XServe you're going to have to provide more information as what you do will depend a little on how the RAID set was created.
HTH?
Tony

Similar Messages

  • How do you know a hard drive is bad?

    how do you know a hard drive is bad?

    From the OS X "Help" system:
    Check whether a disk is about to fail
    You can check the health of many disks in Disk Utility. Many disks include Self-Monitoring, Analysis, and Reporting Technology (S.M.A.R.T) hardware, which lets a disk test itself for potential problems.
    Open Disk Utility.
    Select the disk in the list at the left.
    If you see a message saying the disk has a fatal hardware error, the disk has an irreparable hardware problem that can’t be fixed by Disk Utility or any other utility that repairs software problems. Back up as much of the data on the disk as possible, and then replace the disk.
    If you don’t see a message saying the disk has a hardware error but you still have problems with the disk, you can try to repair it with Disk Utility.

  • How can I Replace a Hard Drive on a 160gb iPod Classic?

    How can I Replace a Hard Drive on a 160gb iPod Classic? I am considering buying an iPod Classic off of eBay which is described as 'broken' and having the 'Red X' showing up on the screen. The seller is starting the bid at a very low price, which raises some concerns for me. For this thread, let us assume that the iPod has a broken hard drive that needs to be replaced in order to function properly. I am assuming that merely 'restoring' it would not suffice. How would I be able to replace the hard drive myself, without bringing it in to a store? I have never fixed an iPod's hardware before, nor a computer or any electrical device. I am a novice at such things. Would I be able to fix it myself without wasting money on a broken iPod and new hard drive? Please provide instructions on how to do so =)

    Hello there,
    Yes, the red X icon is usually a sign of a bad or damaged hard drive. Sometimes, restoring the iPod will resolve the issue, but rarely. Other users were able to smack the ipod against the side of their leg and gain back full functionality of the iPod.
    However, if no such luck with either, your next option would be to replace the drive. For this task, you can either opt to repair and replace the hard drive yourself, or opt to send it into a third party repair business to do the job for you.
    I use the guides at [www.ifixit.com|http://www.ifixit.com> to help me replace broken parts on an iPod. These guides provide excellent step-by-step instructions as well as photos on how to repair any part from an iPod.
    Some other good sites for purchasing repair parts include the following:
    [iDemiGods|http://www.idemigods.com>
    [RapidRepair|http://www.rapidrepair.com>
    [iResq|http://www.iresq.com>
    Lastly, I would also like to remind you that ebay also has several great deals on excellent iPod replacement parts. It's where I purchase a majority of mine.
    Hope this helps.
    B-rock

  • How do you put your hard drive from an old computer to your new mac?

    how do you put your hard drive from an old computer to your new mac?
    i want to get the pictures, etc off of my old mac onto my new mac desktop. how can i do this?

    You don't.
    How to use Migration Assistant:
    http://support.apple.com/kb/HT4889?viewlocale=en_US
    http://support.apple.com/kb/HT4413?viewlocale=en_US
    http://support.apple.com/kb/TS1963
    Troubleshooting Firewire target disk mode:
    http://support.apple.com/kb/HT1661

  • How do I replace a hard drive in 1625CDT?

    I need to replace the hard drive in a 1625CDT. I have a drive, but can't figure out how to get the case open. I also can't find any support documents with instructions how to do this.
    Can anyone supply directions to do this?
    Please don't tell me to take it to a service center. I'm a PC tech and know how to work on computers... just not this laptop.
    I just need directions on how to get inside the case to the HD. Email me offline if need be.
    Thanks

    Hi Roger
    Well, if you are a PC technician so it should be not very difficult for you to change the HDD. A assembling of all notebooks is very similar and it should be possible for you to change or to find the HDD without any detailed instruction.
    But nevertheless I will try to help you:
    Before starting the procedure please remove the battery.
    Then remove the keyboard. To remove the keyboard please remove the Strip cover. The System Status Indicator Panel is designed to snap-fit
    into place. Do not use excessive force to remove or replace it.
    Remove the 3 screws on the unit button. (There are mark K around the screw hole). Remove the four screws holding the keyboard in place.
    Now gently lift the keyboard.
    Pull the keyboard FPC connector and T/P FPC connector safety lock in upward direction.
    Then remove the Combo Module 1 screw. Remove the ram door.
    Remove the Combo Module screw (M2.5+18FP) holding the Combo Module in place.
    Pull up the Combo Module FPC connector.
    Then the Combo Module will be pulled out, you can easily take out the Combo Module entirely easily
    Remove the System Status Indicator Panel. The System Status Indicator Panel is designed to snap-fit into place. Do not use excessive force to remove or replace it.
    Remove the four screws holding the keyboard in place.
    Now gently lift the keyboard, placing it face down on the touch pad. Take care that you dont damage the ribbon cable attached to the keyboard.
    Remove the two screws (M2.5+4FP) securing the hard drive in place.
    Grip the hard drive at the end of the drive carriage. With firm even pressure, slide the hard drive in the direction indicated, you will feel it disconnect. Now lift the HDD out of the bay. Store your HDD Module in a safe, dry place away from direct sunlight or heat.
    Hope this will help you ;)

  • How do I Replace A Hard Drive?

    Ok, I have a Dead Hard drive!
    Hard disc 1 Quick (303)
    I want o replace the hard drive and I do not have recovery discs
    Where is the best place to get these and how do I replace the HD myself
    I have a HP pavillion DM4 notebook PC
    Windows 7
    Thanks

    Possibly, but only if it is the exact same model.
    If you can read all 25 characters of the W7 product key on the bottom of the notebook, you can make your own plain W7 installation media and use that to reinstall the operating system.
    Here's how to do that.
    If you can read the 25 character Microsoft windows 7 product key, you can download plain Windows 7 ISO files to burn to a DVD for the version of windows that came installed on your PC, and that is listed on the Microsoft COA sticker on your PC's case.
    Burn the ISO using the Burn ISO option on your DVD burning program and burn at the slowest possible speed your program will allow. This will create a bootable DVD.
    Or use the Windows 7 USB/DVD installation tool to compile the ISO file you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB method of compilation.
    http://www.microsoftstore.com/store/msstore/html/pbPage.Help_Win7_usbdvd_dwnTool
    Use the 25 character product key on the PC to activate the installation.
    The key will activate either a 32 or 64 bit installation.
    Then go to the PC's support and driver page to install the drivers you need.
    Link to the W7 ISO file downloads is below.
    http://www.mydigitallife.info/official-windows-7-sp1-iso-from-digital-river/

  • How do I replace the hard drive in my Macbook Pro

    Okay...
    I need more space on my computer, so I want to replace the hard drive. I have no OSX install disk, but my computer is running Lion from the app store download. Can I just back up my data onto my new hard drive, and literally just swap them out? Also, how should I back up my drive? should I use a hard drive enclosure with my future drive, and just use time machine or something? Would time machine back up everything? Would the drive become bootable? Please help!

    The best way to do this is buy your new drive.  Get the largest you can buy, and don't buy anything from Western Digital, just a recommendation.  The Samsung 1TB is pretty sweet.  Put that drive in a external encloser (they're inexpensive).  Using CarbonCopyCloner, clone your internal drive to your external one.  This is the cleanest way to do it.
    Then, boot to the cloned drive, just to make sure it works.  It's just a test.  Shut down.  Replace drive (you can find the instructions for your MacBook Pro, by searching the support section of this website, the manual is there).
    Start up with new drive.  Make sure everything is fine.  Use old drive in external enclosure as either a data drive or scratch drive for Photoshop or whatever you do.
    I would set up Time Machine going forward with your new drive.  You need a drive at least as large, and probably 50% larger than your internal drive. 

  • How do I replace the hard drive?

    I got a message that my internal hard drive is failing, and I need to back up the data I can and replace it.
    I'm running a 27' iMac and I can open any of the users except for the main one. The unit just freezes while booting, unless powered up in safe mode.
    Is it possible to do this myself, or ... what options are open to me?
    Thanks.

    If you have never worked on a computer before and, especially, working inside Macs, in general, and iMacs, specifically, then this is NOT a DIY project for you to undertake.
    The aluminum model iMacs are an excersize in patience and tedium to get at anything inside.
    Take your Mac into either an Apple Store  or Apple Authorized repair service center and pay to  have them replace the hard drive.
    Apple uses proprietary hard drives that have a special connection for temp sensors that control the iMac's internal fans.
    Try and get a backup of your data before you bring this in for the hard drive replacement.
    Good Luck!

  • How do i replace my hard drive? dv4

    I have a Pavilion DV4 Entertainment Laptop.  I replaced the hard drive and now it is acting like the drive isn't installed.  When I check BIOS, it says no HDD exists.  Is there something I am missing?  I made sure the drive is seated, it has 3 screws to ensure that.  And even when I plug the old drive in, I get the same message.  There is no HP support for this issue, well none that I don't have to pay for.  Any ideas?
    Thanks

    Hi,
    Check the connection first. Updating BIOS may help. Please also check this:
       http://www.tomshardware.com/forum/296741-30-laptop​-bios-doesnt-detect-hard-drive
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How do you rename external hard drives?

    Hi, can someone please tell me how to name an external hard drive? many thanks

    Please refer to:
    https://discussions.apple.com/thread/3951253?start=0&tstart=0
    your answer is in that thread.

  • What is the proceedure for replacing a hard drive (after failure) for RAID 5 with IX4-300D?

    I have the IX4-300D with 4 hard drives (identical Seagate drives) using RAID 5.
    Someday a hard drive will fail and I and I have to replace it. I read through the users manual briefly and I didn't see any documentation on how to perform a hard drive replacement and not lose any data.
    So here are my questions:
    1) I know per the instructions that Lenovo prefers using identical hard drives. Let's say in 2 years, 1 hard drive fails. Most likely, the same model Seagate hard drive will not be available. So will using a replacement hard drive by the same manufacturer with similar specifications work?
    2) Will the front panel (or the software) tell me which hard drive has failed?
    3) What is the proceedure for replacing a hard drive after a failure occurs? I read that the IX4-300D is not hot-swappable. So do I just power the IX4-300D down, replace the hard drive, and turn it back on?
    Solved!
    Go to Solution.

    Hi exceptionalht,
    It is best to replace the hard drive with one that is the same manufacturer, rotational speed, and capacity, so it does not have to be exactly the same model.
    The front panel should show which drive has failed. If not you can check the web interface to find out.
    That is the basic procedure for replacing a hard drive. You can see a more detailed instructions here: Installing hard drives in an ix4-300d 
    Have questions and need answers?
    Search the database for answers to FAQ's, software/driver downloads, tutorials, news, features and more!
    LenovoEMC Support & Downloads
    LenovoEMC North America Support Contact Page

  • HT1820 how do you restore the hard drive with install cd after zeroing out all files? when i try to boot install disk or from usb a kernel panic screen appears telling me to restart my computer.

    everytime i try to boot installation a message appears saying 'you need to restart your computer. holddown the power button until power is off then press down power button again'. i read that it was a kernel panic. cant boot into any modes but recovery mode with disk utilities but my wireless internet says no wifi hardware installed and sometimes startup manager. this just started after i erased the hard drive and had it overwritten with zeros. its a macbook pro 7,1. bought it in 2011, i think it was made in 2009. it has 320 gb of empty space right now and nothing ive tried seems to work. please help!!!! there is also no os x installed right now due to me zeroing out the hard drive how do i repair it so it will boot to installation?? i can also enter single user mode but do not have root access?

    You are getting a kernel panic because you are trying to boot the computer with a Tiger DVD. That model requires 10.6.3 - Snow Leopard. You can purchase replacement discs from Apple:
    Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
    To contact product and tech support: Apple - Support - Contact Apple Support.
    For Mac App Store: Apple - Support - Mac App Store.
    For iTunes: Apple - Support - iTunes.

  • How do you defragment a hard drive

    HOw do you defragment hard drives in a macpro running mountain lion.

    You don't need to. But if you feel you must:
    You will have to backup your OS X partition to an external drive, boot from the external drive, use Disk Utility to repartition and reformat your hard drive back to a single volume, then restore your backup to the internal hard drive.
    Get an empty external hard drive and clone your internal drive to the external one.
    Boot from the external hard drive.
    Erase the internal hard drive.
    Restore the external clone to the internal hard drive.
    Clone the internal drive to the external drive
    Open Disk Utility from the Utilities folder.
    Select the destination volume from the left side list.
    Click on the Restore tab in the DU main window.
    Check the box labeled Erase destination.
    Select the destination volume from the left side list and drag it to the Destination entry field.
    Select the source volume from the left side list and drag it to the Source entry field.
    Double-check you got it right, then click on the Restore button.
    Destination means the external backup drive. Source means the internal startup drive.
    Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears.  Select the icon for the external drive and click on the downward pointing arrow button.
    After startup do the following:
    Erase internal hard drive
    Open Disk Utility in your Utilities folder.
    After DU loads select your internal hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area.  If it does not say "Verified" then the drive is failing or has failed and will need replacing.  SMART info will not be reported  on external drives. Otherwise, click on the Partition tab in the DU main window.
    Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.  Do not quit Disk Utility.
    Restore the clone to the internal hard drive
    Select the destination volume from the left side list.
    Click on the Restore tab in the DU main window.
    Check the box labeled Erase destination.
    Select the destination volume from the left side list and drag it to the Destination entry field.
    Select the source volume from the left side list and drag it to the Source entry field.
    Double-check you got it right, then click on the Restore button.
    Destination means the internal hard drive. Source means the external startup drive.
    Note that the Source and Destination drives are swapped for this last procedure.

  • My hard drive crashed! How do I replace the hard drive?

    My mid 2010 MacBook Pro 13" started making a horrible skipping/clicking noise when I insterted a disk. It wouldn't eject the disk so I powered it down to restart it, but when it came back on, all that appeared was a grey screen with a flashing file folder and a question mark in the folder. I read that this means my hard drive crashed (I tried holding C upon restart and the 2 or 3 other tips they gave me with no luck.) I having been looking through the forums to see what type of hard drive I need to replace it with, and found my answer...but, I am wondering if those hard drives come with the operating system? Do I need to purchase one and put it onto the new hard drive BEFORE installing it in the computer? Sorry if these are silly ?'s I am not technologically savvy at all!

    It seems your had drive has passed away too.. It means you loose all your data  you haven´t backed-up.
    Chaging the hard drive is very simple, all you need is a new hard drive, internet connection for download the system again, and two types of screw drivers: A very small Philips and a very small Star screw.
    The how to you find in page 37 of the manual:
    http://manuals.info.apple.com/MANUALS/1000/MA1528/en_US/MacBook_Pro_13inch_Mid20 10.pdf
    After you install the new SSD or Hard Drive you have to install the system. To do that push the power button and hold the "OPTION" key on until a small menu to connect wireless network is shown.
    Log on your wi-fi and it will start download the installer of the system. All you need is install the system again, and re-download all your apps even ones you boght in APP Store.
    Hope it helps.!

  • How do you defrag a hard drive

    I am wondering how the best way is to defragment my second internal hard drive. I am trying to set up a partition for boot camp, but it isnt partioning. I am wondering if it is because it needs to be defragged.
    Please let me know how to solve this.
    Thanks

    Caleb,
    It is more likely that the drive is not using the correct partition mapping than it is that fragmentation is causing the problem.
    The easiest way to "defrag" a drive, in this particular case, would be to simply copy whatever data is on it now to another volume, delete it from the original (or erase the original volume), then copy it back. This process copies whatever data you are handling sequentially in both directions, thereby eliminating all fragmentation. The other methods given so far in this thread will all work, but seem a bit overkill in your situation.
    But as I stated, it is more likely that the drive in question isn't using the proper partition mapping. Select the drive in Disk Utility (the drive, not a named volume), then look at the bottom of the window to determine what partition map is being used ("APM," "MBR," or "GUID"). Only drives that are using the "GUID" partition map will support Bootcamp.
    You can change the partition map by partitioning the drive and choosing the GUID scheme from the "Options..." dialogue sheet. In order to use Bootcamp to install Windows, the drive must contain only a single HFS+ partition.
    I'll repeat those important points above: In order to use Bootcamp to install Windows, the drive in question must be partitioned with a single HFS+ volume, and it must also be using the GUID partition map.
    Scott

Maybe you are looking for