How to build a project with no menu...?

Hi all...I am creating a DVD short and I want the DVD to just begin playing with no menu, or at the least, no "theme", just a basic menu. Any idea how to defeat the "Themes" in iDVD?
Thanks!

Here is how I do it: http://homepage.mac.com/profpixel/AutostartDVD/autostart.htm
It creates a DVD that will autoplay and then bring up a black menu that simply says 'Replay Movie'
F Shippey

Similar Messages

How to build a array with high sampling rates 1K

Hi All:
Now I am trying to develop a project with CRio.
But I am not sure how to build a array with high sampling rates signal, like >1K. (Sigle-point data)
Before, I would like to use "Build Arrary" and "Shift Register" to build a arrary, but I found it is not working for high sampling rates.
Is there anyother good way to build a data arrary for high sampling rates??
Thanks
Attachments:
Building_Array_high_rates.JPG ‏120 KB

Can't give a sample of the FPGA right now but here is a sample bit of RT code I recently used. I am acquiring data at 51,200 samples every second. I put the data in a FIFO on the FPGA side, then I read from that FIFO on the RT side and insert the data into a pre-initialized array using "Replace Array subset" NOT "Insert into array". I keep a count of the data I have read/inserted, and once I am at 51,200 samples, I know I have 1 full second of data. At this point, I add it to a queue which sends it to another loop to be processed. Also, I don't use the new index terminal in my subVI because I know I am always adding 6400 elements so I can just multiply my counter by 6400, but if you use the method described further down below , you will want to use the "new index" to return a value because you may not always read the same number of elements using that method.
The reason I use a timeout of 0 and a wait until next ms multiple is because if you use a timeout wired to the FIFO read node, it spins a loop in the background that polls for data, which rails your processor. Depending on what type of acquisition you are doing, you can also use the method of reading 0 elements, then using the "elements remaining" variable, to wire up another node as is shown below. This was not an option for me because of my programs architecture and needing chunks of 1 second data. Had I used this method it would have overcomplicated things if I read more elements then I had available in my 51,200 buffer.
Let me knwo if you have more qeustions
CLA, LabVIEW Versions 2010-2013
Attachments:
RT.PNG ‏36 KB
FIFO read.PNG ‏4 KB

How to write a applet with multiple menu

Hi all,
How to write a applet with multiple menu or please tell me where can I get a examples
thanks

i'm writing a project and it seem not work with browser. If anyone can help please leave me a e-mail so that i can send my source to you.
Thanks so much

Is it possible to build a project with Labview 2010 on a Windows XP system, that is useful for a system with windows 7 on it?

Hi there,
I am planning to use Labview 2010 in a short time.
But before I'm going to use it I have some questions.
I know it is possible to run Labview 2010 in an XP environment. But is it also possible to, when running Labview 2010 on a XP system, to build a project to a version that is useful in a Windows 7 environment?
Or do I have to run Labview 2010, when I want to build a project that is useful on a Windows 7 system, on a system with Windows 7?
Please give me some information.
I hope to hear from one of you soon.
Regards,
Kenny
Solved!
Go to Solution.

Is it possible to build a project with Labview 2009 on a Windows XP system, that is useful for a system with windows 7 on it?
Thanks.
Philippe B.
Certified Associate Developer / Dépt Moyens d'essais
www.ingenia-system.com

How to build a screen with master detail data

Hi ,expert ,
Someone can teach me how to build a screen with master detail table ?
I wnat to build a screen for user to maintain FERT group and FERT detail list in one screen .
just like this ..
MASTER Block
FERT1
FERT2
FERT3
DETAIL Block
FERT1A1
FERT1A2
FERT1A3
when I double click FERT1 in the Master Block the detail view will show FERT1A1 A2 A3
Thanks for your help ....
Moderator message : Not enough research before posting. Spec dumping not allowed. Thread locked.
Edited by: Vinod Kumar on Jun 13, 2011 1:38 PM

An inefficient way to create the array is to use the build array and a shift register as shown below. It's more effecient in terms of memory management to create the array and then use the replace array subset as shown in the other image. Of course, if you don't need the array inside the loop, just wire the value out of the while loop and on the exit tunnel, right click and select 'Enable Indexing'.
Message Edited by Dennis Knutson on 07-03-2007 10:25 PM
Message Edited by Dennis Knutson on 07-03-2007 10:26 PM
Attachments:
Crude Build Array.PNG ‏4 KB
Better Build Array.PNG ‏6 KB

How to share a project with a non-Adobe user and present it to prospect customers?

I Have to share my project with a person who will present it to prospect customers. I cannot ask this person to open an Adobe account. Is there a way for him to access my DPS folio and show it? Or can I export it in a way that allows to appreciate the interaction features built inside?
Thanks!

OK, got it. Thank you!
2015-01-17 14:46 GMT+01:00 Bob Levine <[email protected]>:
How to share a project with a non-Adobe user and present it to
prospect customers? created by Bob Levine
<https://forums.adobe.com/people/BobLevine> in Digital Publishing Suite
- View the full discussion
<https://forums.adobe.com/message/7105349#7105349>

I'm getting an Internal Muxer Error when trying to build a DVD project with still menu images

It originally happened with moving menu content and a help search said it was due to the loop point on a menu being after the end point of the asset but this was not the case.
I've now changed all the menu content to static images and the error is still occurring.

If you want a still image for your DVD menu, click on the Menu in the Outline, then look at the Inspector. Is the Duration set to 0? If not then change it to zero. Also look below that to "At End" and make sure that is set to Still.
Also make sure the image that you imported was a RGB image in either JPEG, TIFF, PNG, or PICT format (PNG would be your best choice), and that the image is SD resolution (i.e., 720x480 for NTSC).

How do I change stills with each menu item selected?

Hi all.
I am trying to create a menu (with 10 items) which contains one single dropzone box, which will contain a still that changes with each menu item selected (instead of 10 different stills next to each item).
I have absolutely no idea how to achieve this! Do I create a different menu for each item? Is there a way to have a slideshow within the menu that changes with each item selected?
Please help!
Many thanks
James

THe way to do what you want to do is layered menus which have some limits
http://dvdstepbystep.com/layersover.php
What you would do is change the item that appears in the same section - in other words there would be ten layers with a diffrerent picture in the same exact spot, the rectangle buttons sections do not need to be over the picture section
http://dvdstepbystep.com/Layers_Example.dmg is a project that does changing images.

How to build a table with predifined? Like Huffman decoding, there are 34 predefined tables?

I am trying to use Labview for mp3 huffman decoding. there are 34 predefined tables for lookup purpose. I tried build array control, but it is so hard to assign value with size of 16. What is the better way to create predefined array? And how to do lookup table with Labview?

IMHO, the best way to have something "predefined" is to read this data from a "setup/configuration" file (if you don't want to use "default settings" LV feature). The choice of the format for all the data that you want to store in some kind of configuration file is up to you.
Also, constructing a "lookup table" in LV doesn't seems different as for any other programming language.

How to build a array with collected data

Hi,
I have collected data from serial port with VISA. Now I want to build a array with 100 date points. Should I connect VISA Read with Build Array directly? How to do it?
PS: All of them are in a While Structure.
Thank you!

An inefficient way to create the array is to use the build array and a shift register as shown below. It's more effecient in terms of memory management to create the array and then use the replace array subset as shown in the other image. Of course, if you don't need the array inside the loop, just wire the value out of the while loop and on the exit tunnel, right click and select 'Enable Indexing'.
Message Edited by Dennis Knutson on 07-03-2007 10:25 PM
Message Edited by Dennis Knutson on 07-03-2007 10:26 PM
Attachments:
Crude Build Array.PNG ‏4 KB
Better Build Array.PNG ‏6 KB

How to build a form with a tree component

Hi, i'd like to know if it's posssible to build a form with
the Flash 8 Tree component.
My menu looks like a tree but the childnodes of this tree are
some form criteria that you can aditionate and post to a serveur.
I try to use the accordeon menu, and it works but my menu
must have dynamic heigth, and open all the boxes like the tree
component...
I'm in a hole... please healp me...
Thinks

Sans,
I am no Apex expert, but with a situation as "complex" as yours, have you thought about creating a VIEW that joins these 7/8 tables, placing an INSTEAD OF trigger on that view to do all the business logic in the database, and base your application on the view?
This is the "thick-database" approach that has been gaining momentum of late. The idea is to put your business logic in the database wherever possible, and let the application (Form, Apex, J2EE, whatever) concentrate on UI issues,

How to build this query with the minumum number of sub-selects?

The question I am trying to answer is analogous to this:
Give me all projects that: (have no employees assigned and are small) or (have only employees with the the last name = "Smith")
Thanks,
Roman

Thank you :
1- I am in 9.0.4.8 version and can not use allOf expression (availible in beta version)
2- I not find .notIn(subQuery) operator in 9.0.4.8 version and i replace it by .in(subQuery).not() !
My new query retrieve Customer who have 0 (zéro) Orders !
How to retrieve only customer (with orders + with orders without "television") ?
My new query is :
<div align="left" class="java">
static void findCustNoComputer (){
 ClientSession cs = TopLinkSession.acquireClientSession();


 ReadAllQuery query = new ReadAllQuery(Customer.class);
 ExpressionBuilder queryBuilder = query.getExpressionBuilder();

 ExpressionBuilder subqueryBuilder = new ExpressionBuilder(Customer.class);
 ReportQuery subQuery = new ReportQuery(Customer.class, subqueryBuilder);
 subQuery.addAttribute("id");
 subQuery.setSelectionCriteria(subqueryBuilder.anyOf("Orders").anyOf("OrderItems").get("product").get("productName").equal("Computer"));
 query.setSelectionCriteria(queryBuilder.get("id").in(subQuery).not());

 Vector allCustomers = (Vector)cs.executeQuery(query);
 Iterator allCustomersIterator = allCustomers.iterator();
 while (allCustomersIterator.hasNext()) 
 {
 Customer tempCustomer = (Customer)allCustomersIterator.next();
 System.out.println(tempCustomer);
 }
 cs.release();
}


Sql of query :
SELECT
 t0.CUST_LAST_NAME, t0.CUST_FIRST_NAME, t0.CREDIT_LIMIT, t0.CUST_EMAIL, t0.CUSTOMER_ID, t0.PHONE_NUMBER2, t0.PHONE_NUMBER1, t0.CUST_STREET_ADDRESS1, t0.CUST_CITY, t0.CUST_STREET_ADDRESS2, t0.CUST_STATE, t0.CUST_POSTAL_CODE
FROM TL_CUSTOMER t0
WHERE NOT (
 (t0.CUSTOMER_ID IN
 (SELECT DISTINCT t1.CUSTOMER_ID
 FROM TL_CUSTOMER_ORDER t4, TL_ORDER_ITEM t3, TL_PRODUCT t2, TL_CUSTOMER t1
 WHERE (
 (t2.PRODUCT_NAME = ?) AND
 ((t2.PRODUCT_ID = t3.PRODUCT_ID) AND
 ((t3.ORDER_ID = t4.ORDER_ID) AND (t4.CUSTOMER_ID = t1.CUSTOMER_ID)))))))
Regards

Problem in build netbean projects with jaxb

Hi, I encounter the problem which I dont' know if it is due to my pc memory insufficient or other reason.
In my netbean projects, I add a Jaxb binding with a local xsd file, but when I try to clean and build the project, each time I have to wait for around 25 minutes, i think it is not make sense to build in such a time. As if I want to debug/run the project each time, it is impossible for me to wait like this.
However, I have to use the xml file in that way, if I can't solve this problem, i have to write / use other method to "eat" the xml file for myself.
Any suggestion or help is appreciated, thx.....

Bishnu,
Thanx for the response.
My problem is whenever i do a little modification in the code, even if i just do some chanes & undo it then also i need to rebuild the application.
There is a single project in my workshop which is pretty huge.As per your reply i am getting only two parts to check & uncheck i.e. If the project is "A" then i am getting A.work & project:A in the build box.
The most important question: Do i need to shut down the server each time i make a small change?Even i have tried this by restarting the server,but every time i get the message that "the Controller.jpf could not compile."
Any idea is most welcome.
Samir

For a READ TABLE how to build a dynamic WITH KEY condition?

Hi All,
I have a Z table with 6 fields. The first field is the Plant and is the key field. This field can be matched with the field from selection screen. Now I have 4 character fields which can contain various values. Now I have another field at the end of the table and this field is the one which I will need for further processing.
Now this last field will be selected based on the data for first 5 fields.
This Read is performed in a loop and the data for all the 4 character fields may not be present.
Now my problem is how to build a Read statement for this table where I need to get the value of the Last field based on the values of first 5 fields?

Hi,
    Use
IF    you have internal table With header line then use
      REad Tablename with key field1 = value1   field2 = value2      field3 = value3        field4 = value4    field5 = value5.
If sy-subrc = 0.
endif.
if you have internal table WithOut header line then use
     REad Tablename into workArea with key field1 = value1   field2 = value2      field3 = value3        field4 = value4    field5 = value5.
If sy-subrc = 0.
endif.
regards,
Amit

How to archive a project with files

Ok the job is done and now i would like to move the project with files from my laptop to a backup hard disk.
I saw that in project manager there is a tool to do that, but what if i already have the video files already copied to the external drive and i just want to backup the missing parts ? ( project files, previews) and how to keep files location updated with new location?
Thanks

ok I just did it, I also moved the preview files in a new folder inside the customer folder and pointed it when launching the copied project file and it works.
So it's all manual or a new clean full copy with project manager.. I wish there was an option that backup in the destination harddrive just the missing files but I can just do it manually.
Thanks!

How to build a project with no menu...?

Similar Messages

Maybe you are looking for