How to configure the server 2012 with NAT settings & 3 public IP addresses

Hi everybody,
I received this from my ISP:
Here's your IP informationMain IP: 70.164.1.165Subnet
Mask: 255.255.255.0
Gateway: 70.164.1.1
DNS1: 68.4.16.30
DNS2: 68.6.16.30
2 additional usable IP's Natted to 70.164.1.165
Usable IP's 70.182.178.97 & 98
Subnet Mask if needed: 255.255.255.252
If you are using one server use 70.164.1.165 as the main IP then add/bind 70.182.178.97 & 98 to the NIC.
For Linux Servers
Network 70.182.178.96
Broadcast 70.182.178.99
If you are using a firewall or router, please make sure you are using 70.164.1.165 on the WAN interface, you can use / NAT 70.182.178.97 & 98 to your server(s).
Main IP can also be natted to your server.
Please make sure shared IP hosting is utilized to conserve IP addresses per ARIN requirements.
I have a Dell server, setup with Server 2012 DataCenter.
I plan to run two VM's running ASP.NET web applications connected using the two additional IP addresses.
I assume I should setup the VM Host to the base address .165 - simple enough no problem and I know how to setup the VM's on their own separate network and I can access the internet - no issues with that.
How do I setup the additional public addresses since they have to pass through the Main address to the correct VM?
I have googled for a few days and my ISP tech people look at me like I want to extract their teeth. Their answer is to sell me a router and set it up. This really does not seem that hard a task.

Try maybe below configuration.
VMHOST
NIC1 - 70.164.1.165
NIC2 - 192.168.0.1
255.255.255.0
NIC3 - 192.168.1.1
255.255.255.0
VM1:
Bind VM NIC1 to VMHOST NIC2
NIC1 - IP1:192.168.0.2 255.255.255.0
IP2:70.182.178.97
VM2:
Bind VM NIC1 to VMHOST NIC3
NIC1 - IP1:192.168.1.2 255.255.255.0
IP2:70.182.178.98
On VMHOST set static traces (use Command Line):
ROUTE ADD 70.182.178.97 MASK 255.255.255.255 192.168.0.2
ROUTE ADD 70.182.178.98 MASK 255.255.255.255 192.168.1.2

Similar Messages

How to configure the wifi access with specific time slot for kids?

how to configure the wifi access with specific time slot for kids?

Which model of AirPort base station do you have? Which version of OS X is your MacBook Pro running?
Wi-Fi access can be limited using the Timed Access feature of the AirPort routers. You would do so using the AirPort Utility.

How to configure the .ini file with applet

hai
i am using native methods in that methods they use some ip addresses. when i am using that native methods in applet run the applet using appletviewer tool it works fine but when i am open that applet using html page browser not configure that .ini file data .how to configure that .ini file with browser

Hi Jay SenSharma,
Thanks for your immediate response.
I saw your URL links, But in your link give the recursive deployment using wlst. But my question is how to configure the oracle weblogic library files into Admin server & Managed Servers by using the wls.jar file through wlst script to create the new domain.
But if create the new domain by using GUI mode then we manually give the admin server port number & managed servers port number and name.
By default the library files are configured with the Admin server in GUI mode. But the Managed server the Library files are not configured with the Managed servers. Then we manually select all the library files to the corresponding managed servers. Then only the applications are deployed into the corresponding managed server.
Regards,
S.vinoth Babu

How to configure Windows server 2003 with WebDav

Can anyone advise on the best way to configure Windows server 2003 with WebDav so I can get the likes of some of those Apps such as PDF Expert and GoodReader to see the folders.
I have installed the necessary services and on a Windows PC and can browse to the URL OK which lists the files (setup using a Virtual Directory).
When I tried using this with GoodReader/PDF Expert, it could not find the server in question.
Can anyone help me?

Hello，
Please make sure you have checked "anonymous users" on receive connector.
Do you mean you can't send an email to external email address? If so, please post the detailed NDR information.
Please use get-receiveconnector | fl cmdlet to check your receive conenctor configuration.
Cara Chen
TechNet Community Support

How to make the server respond with a popup?

I want to make the server respond with a popup?my code is like this,but it does not work,why?
<code>
public class Welcome2
     public static void main(String[] args)throws IOException
          ServerSocket server = new ServerSocket(2222);
          while(true)
               Socket s = server.accept();
               BufferedReader in = new BufferedReader(new InputStreamReader(s.getInputStream()));
               String msg = in.readLine();
               if(msg.equals("visitor"))
                    System.out.println("recv...");
                    JOptionPane.showMessageDialog(null,"Visitor coming!\n");
     System.exit(0);
               server.close();
</code>
it can properly print out "recv...",but no popup,why?

Define "does not work". What happens?
Does your program compile? Do you get an exception? Does the program receive a line? Is the line equal to whatever you expect? Is showMessageDialog() called? Put in some debugging println's to see what happens.

How to configure the jdeveloper 11 with .dbc files?

hi, all
i am a new bie here. 4 jdeveloper 10, i can configure the .dbc files at project setting, while 4 jdeveloper 11, it's totally different. i can't find any place to configure it. How to configure the .dbc in jdeveloper 11?
Regards,
Chelsea

You cant use jdev 11g for OAF development..
You need to download the jdeveloper patch from metalink to develope OAF objects.
Refer this metalink note to find the correct version of jdeveloper that you need to download https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=416708.1
--Prasanna

How to configure the virtual path with our web listener

Oracle Apps Version: 11.5.10.2
Oracle database: 10.2
platform: Windows server 2003
while applying developer 6i patch ( 61954129 ) i got following error which says configure the following virtual path for your web listener
following is the output of forms6iconfig.txt file which oracale suggest to check
Configuration Steps for Oracle Forms installation of 06:21:33 2010/12/01
This file gives details of the configuration steps done for you by the installation process
(marked '[INFO]') and of any actions you need to do manually (marked '[ACTION]'). Please read
this file and perform the requested actions.
[ACTION] If you are installing in a new Oracle Home, please reboot the machine after the installation.
[ACTION] Please configure the following virtual path with your web listener: /dev60temp for
physical directory D:\CLONE\cloneora\8.0.6\tools\web60\temp.
[INFO] NT service Oracle Forms Server [Forms60Server] has been created and started for
the Forms Server.
[ACTION] Please configure the following virtual path with your web listener: /forms60java for
physical directory D:\CLONE\cloneora\8.0.6\FORMS60\java.
[ACTION] Please configure the following virtual path with your web listener: /dev60html for
physical directory D:\CLONE\cloneora\8.0.6\tools\web60\html.
[ACTION] Please configure the following virtual path with your web listener: /dev60cgi for
physical directory D:\CLONE\cloneora\8.0.6\tools\web60\cgi.
[INFO] An internet shortcut to run a standard test form, or any form of your choice, has been
created for you in the Oracle Forms program group.
[ACTION] Please configure the following virtual path with your web listener: /jinitiator for
physical directory D:\CLONE\cloneora\8.0.6\JINIT.

Hi,
while applying developer 6i patch ( 61954129 ) i got following error which says configure the following virtual path for your web listener
following is the output of forms6iconfig.txt file which oracale suggest to check
Do you mean (Patch 6194129)? How do you get this error? Is it at the beginning or the end of the installation?
Configuration Steps for Oracle Forms installation of 06:21:33 2010/12/01
This file gives details of the configuration steps done for you by the installation process
(marked '[INFO]') and of any actions you need to do manually (marked '[ACTION]'). Please read
this file and perform the requested actions.
[ACTION] If you are installing in a new Oracle Home, please reboot the machine after the installation.
[ACTION] Please configure the following virtual path with your web listener: /dev60temp for
physical directory D:\CLONE\cloneora\8.0.6\tools\web60\temp.
[INFO] NT service Oracle Forms Server [Forms60Server] has been created and started for
the Forms Server.
[ACTION] Please configure the following virtual path with your web listener: /forms60java for
physical directory D:\CLONE\cloneora\8.0.6\FORMS60\java.
[ACTION] Please configure the following virtual path with your web listener: /dev60html for
physical directory D:\CLONE\cloneora\8.0.6\tools\web60\html.
[ACTION] Please configure the following virtual path with your web listener: /dev60cgi for
physical directory D:\CLONE\cloneora\8.0.6\tools\web60\cgi.
[INFO] An internet shortcut to run a standard test form, or any form of your choice, has been
created for you in the Oracle Forms program group.
[ACTION] Please configure the following virtual path with your web listener: /jinitiator for
physical directory D:\CLONE\cloneora\8.0.6\JINIT.Please make sure you source the application env file before applying this patch, and select 8.0.6 ORACLE_HOME.
Thanks,
Hussein

How to link Microsoft server 2012 with my windows app.

I have created an app which describes my university and I want to link a Microsoft Server 2012 machine so that i can send updates to the app users at any instance of time. I am using java script to code my app .....I am very new so please help!!!!
Thanks in advance....

Hi Manojit
Thank you for posting in the MSDN forum.
Since Visual Studio General Forum which discuss Visual Studio IDE usage, so I’m afraid that it is not the correct forum for this issue.
To help you find the correct forum, could you please tell us which kind of app you create? Is it a WinForm app or other? What does “Link Microsoft
server 2012” mean in your app?
Thanks for your understanding.
Best Regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click HERE to participate the survey.

How to configure the eth1 port of NIcRIO 9024 to another IP address and subnet mask

Hi ,
I am using cRIO 9024 and am planning to configure it to be an MMS server that interacts with a client which is in another network with different IP and subnetmask. I want to run the server VIs from the host computer via the eth0 port and want to communicate the MMS messages through the eth1 port. the eth0 port is configured as a static IP as shown in the screenshot attached and would like to assign a separate IP and subnet mask to the other port . But when I try to save the configuration I get the error "Could not save your changes tot he target.The subnet mask for eth1 is invalid" .
I have already directly cross connected the Crio and have disabled the firewalls and still am not able to configure it.
1) is it possible to configure the ethernet ports to have separate IPs corresponding to different networks and thus the subnet masks?
2) If its possible then what is the mistake i am doing while configuring it ?
I would be extremaly grateful to have a reply on this as its pretty desperate to spend a lot of time just to set up the IP configurations..!!!!!
Regards
Abhinav

Dear Abhinav,
I'm sorry but what you are tryining to do is not suported by the Second Ethrnet Port on any cRIO and so you getting this error meeage.
Here a abstract out ouf the KnowledgeBase How do I Configure the Dual Ethernet Ports on Real-Time Controllers?:
Ethernet port 2 is currently not supported to communicate outside its own subnet. There is no capability of configuring the Default Gateway for Ethernet port 2 and therefore cannot connect to a large isolated intranet. However, there appears to be a common misconception that this port can only be used for communication between NI products: this is not the case, though any communication through the secondary port must be within the same subnet.
Kind Regards,
SG3 | Applications Engineering | National Instruments | NIG |

BI 4.0 How to configure the server properties in CMC

The BI 4.0 administration guide only gives information about core service ( in the appendix ). Where to find the explanation of properties for other servers like dashboard design / federation servers. Thesehave some specific parameters and there is no documentation as to what these mean and what should be the values in them.
Thanks
Sanjay

hi,
Please refer below link for respective sections.
http://help.sap.com/businessobject/product_guides/boexir4/en/xi4_bip_admin_en.pdf
24.1.8 Dashboard Design Services Properties
Dashboard Design Cache Server Properties
Table 24-42: Dashboard Design Cache Service Properties
Dashboard Design Processing Server Properties
Table 24-43: Dashboard Design Processing Service Properties
Table 24-44: Single Sign-On Service Properties
25.1.11 Dashboard Design Server Metrics
Table 25-23: Dashboard Design Processing Server Metrics
24.1.6 Data Federation Services Properties
Table 24-34: Data Federation Service Properties
Regards,
Vamsee

How to configure portal server with the Backend Oracle database

Hi Portal Experts,
we are planning to install Netweaver 04s sp stack 9 full java edition with Oracle 8i on windows platform.
we have the installation docs of portal but we didn't have any idea about how to configure Portal server with the Backend Oracle database at the time of installation or after ost installation of portal.can anyone provide the documentation about this or guide me how to achieve this.
PLZ share ur views---your help would be highly appreciable.
Regds
Phani.

HI
if you r working in Sap enterprise portal use for connection url
jdbc:sap:sqlserver://ilsql01.tlv.sap.corp:1433;DatabaseName=Northwind
ilsql01.tlv.sap.corp:1433 this is your portal url with port number
Northwind is your database name.
for dirver you need to give
com.sap.portals.jdbc.sqlserver.SQLServerDriver
in case if you r working on other than sap say windows along with oracle try to use
Connection URL as jdbc:oracle:<drivertype>:@<database>
Driver name as oracle.jdbc.driver.OracleDriver
ex jdbc:oracle:thick:@localhost:3036:mydb
Oracle implements two types of JDBC drivers:
Thick JDBC drivers built on top of the C-based Net8 client, as well as a Thin (Pure Java) JDBC driver to support downloadable applets. Oracle JDBC drivers are used to create JDBC applications to communicate with Oracle databases.
Oracle extensions to JDBC include the following features:
Data access and manipulation
LOB access and manipulation
Oracle object type mapping
Object reference access and manipulation
Array access and manipulation
Application performance enhancement
*************if the information is helpful to you please reward points************

ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (ex., 5 min) using the SLA?

I have ASA 5505 8.4. How to configure the switch to the backup channel to the primary with a delay (for example 5 min.) using the SLA monitor?
Or as something else to implement it?
My configuration for SLA monitor:
sla monitor 123
type echo protocol ipIcmpEcho IP_GATEWAY_MAIN interface outside_cifra
num-packets 3
timeout 3000
frequency 10
sla monitor schedule 123 life forever start-time now
track 1 rtr 123 reachability

Hey cadet alain,
thank you for your answer :-)
I have deleted all such attempts not working, so a packet-trace will be not very useful conent...
Here is the LogLine when i try to browse port 80 from outside (80.xxx.xxx.180:80) without VPN connection:
3
Nov 21 2011
18:29:56
77.xxx.xxx.99
59068
80.xxx.xxx.180
80
TCP access denied by ACL from 77.xxx.xxx.99/59068 to outside:80.xxx.xxx.180/80
The attached file is only the show running-config
Now i can with my AnyConnect Clients, too, but after connection is up, my vpnclients can't surf the web any longer because anyconnect serves as default route on 0.0.0.0 ... that's bad, too
Actually the AnyConnect and Nat/ACL Problem are my last two open Problems until i setup the second ASA on the right ;-)
Regards.
Chris

How do you configure the server in this situation?????????????

Hi,
We have Oracle 10.2 and Windows 2003.
We have Oracle on Cluster (with Windows software).
When the System are without cluster all its OK!!!!!!
We have 2 Resources Cluster Group: Oracle and Applications.
We have Oracle in Oracle cluster group.
We have W Drive and a ftp program in Application cluster group.
We have C drive in both nodes. We have installed Oracle in both nodes but we have W drive only associate to the Active Node because is a Cluster resource (Application cluster group).
All days we receive text files by ftp and we put it on W Drive. This text files are readen with external tables in Oracle.
We have a problem when oracle fails and it goes to the another node (for ex. node2) because the external tables fail because the files are on Node1 on W Drive. If we move manually Applications cluster resource to Node2 then all it is OK.
We think to put UNC pathes instead of W but its not possible (Metalink: Note:290703.1)
How do you configure the server in this situation?????????????
Thanks!

We run a similar configurations and i doubt you have a chance other then reconfigure your setup. The way we do it is to have an ftp client in our database group and periodically transfer the files a second time (not elegant but it's working).
If that's not an option you might be able to use unc names in your ftp server and set the ftp root to a directory hosted on a disk which is part of the database group.
Or move to unix (that's what we do now). Than you don't have to bounce your server once in a month to apply security patches...

How to configure the .EAR to the OC4J server step by step ?

I have configured the JavaBean of the OC4J server with the following step:
1.create the eosp.ear with the JDeveloper's wizard
2.copy the eosp.ear to the OC4J Server with the Path:
J2EE_HOME/applications/
3.modify the server.xml and add the following words:
<application name="eosp" path="../applications/eosp.ear" auto-start="true"/>
4.restart the OC4J server and show the information:
Auto-deploying eosp (New server version detected)...
5.create the new JSP and this source code is:
<%@ page import="com.beautybeard.eosp.common.*"%>
<%@ page import="com.beautybeard.eosp.constant.*"%>
6.visit the JSP and show the error information:
Error parsing JSP page /eosp/usr_profile/login.jsp
Syntax error in source/eosp/usr_profile/login.jsp.java:5: Package com.beautybeard.eosp.common not found in import.import com.beautybeard.eosp.common.*; ^/eosp/usr_profile/login.jsp.java:6: Package com.beautybeard.eosp.constant not found in import.import com.beautybeard.eosp.constant.*; ^2 errors
why?
why can not find the package?
please help me out

Hi Sky-
It looks like you have a web application only.
You need to create a war file as described above. A war file is a jar'd file containing your web components, including your javabean class files, etc. JDeveloper 9i can do this for you. You've already done the hard work. Suppose that the project you have created that contains your javabeans, etc in JDev 9i is called myproject (with myproject.jpr as the project file). Right click on the myproject.jpr in the JDev navigator and select 'new...', go to Deployment Profiles and select J2EE Web Module (WAR File) - a general screen will pop up asking you to save the deployment profile (you can just use the default if you want). Once you select OK on that, you will get a screen that calls itself the J2EE Web Module Deployment Profile Settings. This is the screen that you can use to enter your information.
Your servlet and javabean classes will go into WEB-INF/classes subdirectory that you see to your left in this window. Simply select the WEB-INF/classes entry and it will display a list of your java sources (it will only place the compiled output in this directory - there is a toggle for it).
Once you have specified that your javabean and servlet classes go in this directory, you should be set. Go ahead and save / close. In your navigation screen under your project (myproject.jpr or whatever your project name is) you will see your files, jsps, etc and something called webapp1.deploy (if you accepted the default). If you right-click on that, you will get a menu that asks a number of things, one of which is to Deploy to EAR file. Select that entry and it will create an ear file for you. You can play with the various settings to change the name of the ear file, but that's about all you have to do. Once this is completed, you can put the EAR file on your linux box or wherever you want, adjust your server.xml and default-web-app.xml files and launch the app!
Good luck!
Ray
Hi,Ray
Thank you for giving me the detail information!
I'm sorry that I can not give the detail and clear problem ,which make you delusoried.
ok,now I give you my aim.
1. I will construct my application system with JavaBean(not EJB),Servlet,JSPs (linux+IAS+JDeveloper+Oracle8i database)
2. I will package business function with JavaBean. example:
* CheckLogin.java
package com.beautybeard.eosp.javabean.usrprofile;
import com.beautybeard.eosp.common.*;
import com.beautybeard.eosp.data.*;
import java.io.*;
import java.lang.*;
public class CheckLogin{
public CheckLogin()
//do nothing here
public boolean getCheckLogin(){
3. I will control the request and response with Servlets.
example:
*CheckLoginSevlet.java
package com.beautybeard.eosp.servlet.usrprofile;
import javax.servlet.*;
import javax.servlet.http.*;
import java.io.*;
import java.util.*;
import java.sql.*;
import com.beautybeard.eosp.servlet.*;
import com.beautybeard.eosp.javabean.usrprofile.*;
public class CheckLoginServlet extends DefaultServlet
public void service(HttpServletRequest req,HttpServletResponse res) throws IOException, ServletException
//use the JavaBean
CheckLogin cl = new CheckLogin();
if (cl.getCheckLogin){
res.sendRedirect("login.jsp");
}else{
res.sendRedirect("err.jsp");
4. I will display the result with JSPs:
example:
<%//login.jsp%>
<%@ page import="com.beautybeard.eosp.common.*"%>
<%@ page import="com.beautybeard.eosp.data.*"%>
5. I have success on running the above steps in the 9iJDevelper(pure java) environment(OS:Windows 2000 Server), and now I will move the JSPs ,Servlets,JavaBeans to the Server(linux) without the JDeveloper's deployment wizard.
how to configure the IAS to carry my point?
thank you!
Sky liu

How to configure the ESS portal in ehp 6 server?

Dear All,
Pls advice me how to configure the ESS portal in my client server?
I want to create new iviews ,pages,workset and link them all to R/3,with total configuration steps please.
Thanks and Regards,
Pradip

hi pradeep ,
which version r u using wdjava or abap ? ......if ur using java you have to do all in home page framework and if you are using with launchpad from EHP5 better you can create it from launchpad by going to t -code LPD_CUST and select the ROLE:ESS and INSTANCE: MENU
REFER Below............
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/e09b3304-07d8-2b10-dbbf-81335825454f?QuickLink=index&overridelayout=true&38388417774934
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/21eb036a-0a01-0010-25a3-b2224432640a?QuickLink=index&overridelayout=true&5003637159921
http://wiki.scn.sap.com/wiki/pages/viewpage.action?pageId=31476&bc=true
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/108c31e7-b6a7-2d10-3692-c1a9f7a5c4dc?overridelayout=true

How to configure the server 2012 with NAT settings & 3 public IP addresses

Similar Messages

Maybe you are looking for