How to install driver for canoscan 9900F with Mac OS 10.6

I have been looking for 18 months for driver to use for canoscan 9900F with MAC OS X. Neither canon or apple supported their compatibility
Now a bulletin came out on 4/14 http://support.apple.com/kb/ht3669
This lists canoscan 9900F as supported by snowleopard
I tried to add scanner but it did not find it
I downloaded and opened driver from canon but it still doesn't recognize it, when I go to system preferences and select print fax and select add printer.
Pleas help... Thank you

Read this about Mac setup.... http://support.hp.com/us-en/document/c04510394/

Similar Messages

  • How to install Windows XP in parallel with Mac OS on a Macbook?

    Can anyone tell me how to install Windows XP in parallel with Mac OS on a Macbook?
    If I divide the hard drive into 2 patritions and install Win XP & Mac OS on each patrition, is it ok?

    I don't think he meant "Parallels", I think he just meant "parallel", with a little 'p'.
    There are three options for running Windows software on an Intel-based Mac:
    Virtualization: you can install software such as Parallels or VMWare (along with a licensed copy of Windows) which will emulate the environment necessary to run Windows software. Performance is significantly degraded, but you can work with both Windows and Mac software simultaneously.
    Dual boot: You can use Apple's Bootcamp to partition your drive and create a CD of Windows drivers for your devices, so that you can then install Windows on one partition of your drive. Your Windows software will run just as it does on any other Windows PC, but you have to reboot to switch between Windows and OS X.
    Crossover: Crossover is a product that allows you to run Windows programs in OS X without installing Windows. Not all Windows software will work with Crossover though.

  • How to install driver for Windows 8.1 without physical connection

    I have a Photosmart 7762 printer connected to a NAS box (with wiring all very difficult to get to behind various office units) and want to be able to print to it from a new Windows 8.1 PC that is installed (again with difficult to get to wiring) in a separate room but on the same network.
    The HP site for the printer says I have to use Windows Update to get the driver, but this only works if you physically connect the printer to the PC which isn't an easy thing to do in this case.
    Does anyone know where I can get hold of the driver so I can use the "Have Disk" option? I have been unable to find it anywhere. Alternatively, does anyone know how to copy the driver from an existing Windows 7 install (on a laptop I could connect it to) and whether that would work?
    This question was solved.
    View Solution.

    Hi,
    Folow the steps listed under Download the driver for later use or use on another computer below, it will allow downloading the INF and installing those manually, be sure to follow the link to Microsoft which explain how to locate the correct package and extract it:
    http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c03470332&DocLang=en&docLocale=en_US&...
    Shlomi
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • How to install  driver for Intel Pro 1000 PCI Network-card

    Hello,
    I just bought the a.m. Intel Pro 1000 Network adapter, but I don't know at all how to install the driver for Solaris 10.
    The installation instructions delivered from Intel didn't help me at all, because I can't uncompress the INTCGigae.pkg and the INTCGigaE.tar.z files.
    I copied them to /tmp and folllowed Intel's Installlation Instructions.
    Please keep in mind I am new to Solaris 10, with no Linux/Unix experience, when helping me.
    Thanks in advance for help and assistance.

    Hi!
    And what happens if you install the driver from the Toshiba WLAN portal:
    http://aps2.toshiba-tro.de/wlan
    I still dont know what you mean with Askey for Toshiba
    You should try to install the driver manually. Choose in device manager the WLAN card, right click and select Update Driver. Choose the advanced installation where you can choose the driver directory yourself and navigate to the folder where you have stored the downloaded driver.

  • How to install driver for HP photosmart 7520 on MacOSX 10.5.8???

    My husband does basic printing of documents.  His computer is a MAC OSX 10.5.8.   We have a new HP Photosmart 7520 printer which requires 10.6 minimum. 
    Is it possible to get a driver for this printer for him, that will allow him to access the printer, without getting a new computer!!  ??  To simply be able to print and fax and scan.. he rarely does photos. 
    Please Help, as of course, he is quite frustrated, and as a result, so am I!!
    Thanks.

    Hi grammaglenys,
    Welcome to the HP Forums! I see that you having trouble installing drivers with your printer. It is true that this printer only supports Mac OS X 10.6 as the minimum requirement for the HP Photosmart 7520.
    As the Operating System is older than when the printer came out, there currently isn't a driver available. However, here is a list of printers that can be used with Mac OS X 10.5.8. Archived - Mac OS X 10.5.3: Printer drivers included in the HP Printer Driver Update v1.1.1. Or you can try upgrading the Operating System to Mac OS X 10.6.
    Hope this answers your question, and have a great day!
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

  • Help formatting Hard Drive for best compatibility with Mac OSX 10.5!

    I have a 1TB hard drive that I recently purchased. I would like for format it for best compatibility with Leopard. I must be doing something wrong because everything I try, I get an error.
    Here's the details of my drive.
    What do I need to do in Disk Utility?
    Disk Description : WL1000GS A1672 Media
    Total Capacity : 931.5 GB (1,000,204,886,016 Bytes)
    Connection Bus : USB
    Write Status : Read/Write
    Connection Type : External
    S.M.A.R.T. Status : Not Supported
    USB Serial Number : 240077140FFF
    Partition Map Scheme : Master Boot Record
    Main Partition (Only managed to get it's name to CORY.):
    Mount Point : /Volumes/CORY
    Capacity: 931.5 GB (1,000,204,853,760 Bytes)
    Format : MS-DOS (FAT32)
    Available : 931.3 GB (999,959,166,976 Bytes)
    Owners Enabled : No
    Used : 1.4 MB (1,507,328 Bytes)
    Number of Folders : 0
    Number of Files : 0

    Looks like that's working. My problem was I didn't select GUID Scheme. Thanks.
    EDIT: Yup that did the trick. Thanks so much.

  • How to install Arch for dual-boot with Win 7 (on 2 hard drives)?

    Hello,
    the TLDR first: how exactly should I proceed when setting up GRUB for 2 hard drives to dual-boot Arch (64 bit)and Win 7 (64 bit)?
    Long version: So, I have the following hard drive & partition layout:
    On my first hard drive (250 GB big) I have: Win 7 64 bit, all the programs for Windows and of course the EFI partition
    My second hard drive is 1 TB big and formatted in NTFS and it only contains data. It has 2 partitions, one is about 750 GB big and used for simple storage.
    Sidenote 1: sometimes my disk management (Windows' own gparted) shows either the little disk or the big one as disk 0. Don't know what exactly this means, but I have never ever experienced any problems whatsoever during use.
    Sidenote 2: the UEFI motherboard (ASRock H67M) cannot boot into Legacy mode.
    I want to install Arch on a ~200 GB partition on the second hard drive (the one with 1 TB). (click here if you want to see a screenshot) I am posting this because I am confused with how exactly I should deal with the whole "2 hdds & UEFI" thing.
    So how exactly should I proceed when setting up GRUB for this setup?
    For partitioning I suppose I would have to use fdisk or cgdisk. I used cgdisk before and found it to be straightforward. Then, because I have experienced my fair share of problems with rEFInd, I'd like to use GRUB.
    Last edited by jones (2013-06-29 14:36:56)

    First thing you should do is become familiar with your motherboard.
    http://www.asrock.com/mb/manual.asp?Model=H67M
    This will probably help you out in understanding the sidenote 1 thingie (hdd's on sata3 and/or sata2 connectors)
    As on sidenote 2, according to the manual it seems to be possible to boot legacy mode,  see Storage Configuration.

  • How to install applications for multiple iPads with one ID?

    Hey guys,
    I have to prepare many iPads for work, and I've found the process to be very redundant. In order to ensure that the applications are tied to the ID of the final client, I have to first create an account under my email, download all the applications and then change the email to the client's. Now when I have to prepare another device, I have to delete the applications in iTunes and re-download them with a new account to make sure they are tied to the next ID. Is there a way to download and sync all the applications under one ID, and not have issue with updates in the future? Keep in mind I'm only installing free applications.

    I was referring in particular to the logs that are created by Workshop
    itself (in the workshop directory). It creates workshop.log and netui.log.
    Raj Alagumalai wrote:
    Steven,
    which workshop log file are you referring to ?
    the workshop log files are usually saved to the domain directory.
    If the developers are each going to start their own server instances then
    there should be no issues.
    The best option for you is to create multiple domains for each developer.
    They will share the same workshop installation, but they will each have
    their own instances.
    Thanks
    Raj Alagumalai
    WebLogic Workshop Support
    "Steven Ostrowski" <[email protected]> wrote in message
    news:[email protected]..
    Hello,
    What is the best way to install the WL 8.1 Platform for multiple
    developers on a single UNIX machine? These developers may start
    concurrent instances.
    The problems I see are that the log files generated by Workshop would
    be shared among concurrent users, permissions would need to be set so
    that the user that is running the instance that creates the log files
    will need to create the file with permissions that everyone can use. Are
    there any other issues to doing this?
    I could not find the information on this in the documentation.
    Thanks

  • How to install driver for Intel HD on Satellite C660-22V?

    Hi
    I could not reply below so here is my question.
    http://forums.computers.toshiba-europe.com/forums//thread.jspa?threadID=68240
    As*** I do not know if you work for toshiba but what else am I suppose to do if the driver installed on a new laptop does not allow me to use my software?
    The software is ArcGIS and would be widely used.
    Seems like it has been 2 years since the driver was updated by Toshiba so what good is that?
    I would expect the laptop to work out of the box as the specs met the system requirements for the software.
    Will there be an update in the future?

    Hi
    This seems to be a user to user forum so would not expect to get answers from Toshiba here
    > Seems like it has been 2 years since the driver was updated by Toshiba so what good is that?
    > I would expect the laptop to work out of the box as the specs met the system requirements for the software.
    Where is a problem? The Satellite C660-22V supports Intel graphic card.
    Visit the Intel page to get the latest graphic card driver.
    If you would not be able to install this using the install.exe, go to device manager and install/update the graphic card driver via device manager
    Use the advanced install option to point to the driver folder containing the latest driver files thats it

  • Driver for Photosmart c309a with Mac OS 10.10 (Yosemite)

    I'm planning on upgrading to Yosemite, Macs OS 10.10 but don't know if my Mavericks driver will work or if I need to download a new one.  If I need to download, can someone tell me where to find it? I'm completely lost in the drivers section. So many links and so confusing.  Thanks, Michele

    Read this about Mac setup.... http://support.hp.com/us-en/document/c04510394/

  • How can I install attachments for SAP notes with zip-files ???

    How can I install attachments for SAP notes with zip-files ???

    Can you elaborate on your question? How exactly is your question related to SAP NetWeaver Portal: Application Integration? If you are really asking how to install attachments contained in SAP notes, there is no automatic/general way and you should ask your question in the Software Support and Maintenance space to begin with. What SAP note(s) are you looking at installing?

  • Install driver for HP Laserjet PRO CP1525nw in my MacBook with OS X Yosemite

    install driver for HP Laserjet PRO CP1525nw in my MacBook with OS X Yosemite V 10.10.1 (I have the disk but it doesn't load the driver)

    Hi @Peggysguy ,
    I see that you are having issues installing the printer on Yosemite. I will certainly do my best to help you.
    The CD won't support Yosemite. You just need the newest drivers to install.
    I have provided you with the downloaded Full Software drivers for the Laserjet Pro CP1525nw.
    HP LaserJet Professional CP1525 Color Printer Series Full Software Solution.
    If you need further assistance, just let me know.
    Have a great day!
    Thank You.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • Installing driver for onboard NIC

    I'm new to Solaris and have a question as to how to install drivers for my onboard NIC. I found drivers that might work but I don't know what to do with them. Do I use the tar command? Will it put it in the right directory that way or do I need to move it somewhere else first.
    If the drivers work, can I then set it up for DHCP? I've read a little bit about it. Will this work: ifconfig <interfacename> auto-dhcp?

    Before this gets completely out of hand, like a recent thread,
    let's get a few things out of the way.
    What hardware do you have? Brand? Model?
    What precise Ethernet chipset do you have?
    Integrated to the systemboard? Add-on card ?
    If this is some sort of a PC, have you checked the
    Solaris Hardware Compatibility List (HCL)
    http://www.sun.com/bigadmin/hcl/data/sol/
    and have you compared your hardware to what's on that list ?
    Generally speaking, there is no such thing as "maybe" or "might work"
    when you are speaking of driver software packages.
    They would be correct or they would be wrong.
    What driver software are you considering?
    If you downloaded it, provide the link.
    There should be a README file with the software, even if it's not named "readme".

  • How to install drivers for ati radeon 3200?and how to config xorg.co ?

    how to install drivers for ati radeon 3200?and how to config xorg.conf?

    mawch wrote:how to install drivers for ati radeon 3200?and how to config xorg.conf?
    Hello
    I am using ati hd 3200 which is integrated with my motherboard. If you are using arch you can download & install through pacman. The package is named like catalyst*. You can install them by issuing as root user
    #pacman -Sy
    #pacman -S -l | grep -i catalyst
    #pacman -S catalyst catalyst-utils
    After installation reboot your machine in runlevel 1. (single mode).  Ensure "fglrx" module is loaded correctly using
    #lsmod | grep -i fglrx
    If the resultant output have "fglrx" part  the module is loaded correctly. The next step is to create a working /etc/X11/xorg.conf. Backup your current xorg.conf if needed.
    #cp /etc/X11/xorg.conf /etc/X11/xorg.conf.bkup
    Then issue
    #aticonfig --initial --input=/etc/X11/xorg.conf
    This will create a new xorg.conf file. Now we can test our confign.
    #telinit 3
    I am using runlevel 3 to avoid graphic messup!!
    issue
    #gdm
    If you graphical login screen works correctly there is nothing to do more except adjust your monitor resoloution as you like.
    To know your ati driver is working correctly issue as root
    #fgl_glxgears
    If gears are rolling happily it seems correct. You can also know more about installed ati driver
    #fglrxinfo
    Now the installed driver version is in the output 
    If there is any problem try following
    ##### Soloutions to solve various display problems using ATI Catalyst Drivers in Linux #####
    yes video playback is choppy until i ran :-
    sudo aticonfig --overlay-type=Xv
    Try adding the following to the 'Device' section in /etc/X11/xorg.conf
    Option "TexturedVideo" "true"
    ### This is a half solution for mythtv problems. Run mythtv in window (no full screen) If You have a screen resolution of 1024x768 try the command;
    mythfrontend --geometry 800x600
    Append the "Device" Section of /etc/X11/xorg.conf file as follows;
    Section "Device"
    Identifier "Videocard0"
    Driver "fglrx"
    Option "OpenGLOverlay" "off"
    Option "VideoOverlay" "on"
    Option "TexturedVideo" "on"
    Option "TexturedVideoSync" "on"
    Option "Capabilities" "0x00000800"
    BusID "PCI:1:0:0"
    EndSection
    Add following in the .bashrc of each user or /etc/bashrc file* Most Effective In My Case!!
    export LIBGL_ALWAYS_INDIRECT=true
    ####### Arch Linux - Add the "nopat" option to the /boot/grub/menu.lst or /boot/grub/grub.conf
    ####### as in the following example
    title  Archlinux Ice Kernel
    root   (hd0,1)
    kernel /boot/vmlinuz26-ice root=/dev/sda2 ro resume=/dev/sda3 quiet splash nopat
    initrd /boot/kernel26-ice.img
    NB: REGULAR DISCLAIMER IS ALSO APPLICABLE TO THE ABOVE MATTER; USE IT AT YOUR OWN RISK !!!  ALL THE ABOVE INFORMATION IS COLLECTED FROM VARIOUS POSTINGS IN THE FORUM AND FROM MY OWN EXPERIENCE
    Wish U good luck
    mvdvarrier

  • Satellite A100-599 - Unable to install driver for nVidia GeForce Go 7600

    Greetings to all!
    Trying to install driver for Nvidia GeForce Go 7600 after complete system reinstall, but without any success. Only safe mode is available after this driver installation, tried with Windows XP, Vista and Windows 7 and with different drivers from Nvidia and Toshiba sites - same result all the time :(
    Would be glad to realize how to solve this... Thanks a lot.
    Satellite A100-599
    Current OS: Windpws Vista Home premium sp1.
    Message was edited by: Airtoground

    I do not want to install XP again, will try to fund a solution for Vista. Here is what I got from Installs list:
    Component List Satellite A100 PSAAR; Satellite Pro A100 PSAAs; Satego A100 PSAAW
    Contents and Installation order
    for Windows VISTA
    Windows Vista 32bit Home Premium - Windows Vista Home Premium&Basic(English) RTM
    - SLP Module OEMSLP2.0
    - Sun Java 2 Runtime Environment v1.6.0
    1 KB928190(For updated USBHub.sys) KB928190
    2 TOSHIBA Value Added Package Please use the attached ini file for ButtonSetting.ini and FeatureSelect.ini when the TVAP installation. v1.0.7
    3 Intel 945GM/940GML Display Driver v7.14.10.1114 (Package:V15.0.1.1114 PV)
    4 ATI ATI M52P/M54P/M56P Display Driver V8.31.100.3.2-061124a2-039454C
    *5 Nvidia G72M/G72MV/G73M Display Driver v97.46(TBD)*
    I found this driver but it says "no suitable driver found, installation wizard stops its work".
    Any ideas what could it mean?
    Thanks to all.

Maybe you are looking for