How to make copy client with customizing but with no deleting appl.data

Hello,
Which profile of copy client i need if i want make copy customizing without deleting application data in target client.
regards,
Denis

hello dennis,
There is no way you can do that, you cannot copy only customizing onto a client without deleting the application data since there is no such profile in the client copy profiles to do so.
Also, to me it seems a bit strange to keep the application data (which depends on customizing for integrity) and update the customizing with something else!
However, still if you wish to do this, there is a crude way of doing it (theoratically). You could use the client copy by a transport request where in you club all your customizing transport requests into one single transport request using transport of copies and then use the client copy via transport request to copy the customizing.
Here are the steps:
1. Create transport of copies [click here|http://help.sap.com/saphelp_nw70/helpdata/EN/57/38e1a94eb711d182bf0000e829fbfe/frameset.htm]
2. Copy the newly created transport request into the target client via copy by a transport request functionality.
click the following link for the same:
[client copy via transport request|http://help.sap.com/saphelp_nw70/helpdata/EN/69/c24c754ba111d189750000e8322d00/frameset.htm]
Regards,
Siddhesh

Similar Messages

How can I copy a Font Book library with "Collections" to my 2nd laptop?

How can I copy a Font Book library with "Collections" to my 2nd laptop?
I have a number of fonts (approx. 500) on my work laptop which are sorted to different Collections. I'd like to have a copy of the Font Book library with Collections on the laptop I use at home to work. I'd think there was a more straight forward way to do it, but I haven't found any posts regarding the matter so any help would be appreciated.
Thanks

To anyone who is reading this based on needing to copy their Font Book to another machine as I do, there is a way to make a copy of the fonts in Font Book by going to file/export fonts. Keep in mind that you will need to have all the fonts selected (command A) in your "All Fonts" list for them to be exported. You will then have a new folder saved to where ever you chose, with all your Font Book fonts in it.

How to make 2 clients on same VLAN communicate to each other when tunnel-loop-prevention is enabled?

Requirement:
How to make two clients on same VLAN communicate to each other when tunnel-loop-prevention is enabled on tunneled-node configuration at controller?
Whenever we enable tunnel-loop-prevention on controller while we configure tunneled-node, the communication between two tunneled-node client on same VLAN is blocked or dropped.
If the tunneled-node clients are of different VLANs then they can communicate between them even when the tunnel-loop-prevention is enabled on the controller.
Solution:
To make two tunneled-node client on same VLAN to communicate between them, we need to enable "local-proxy-arp" for the interface VLAN on the controller.
Once it is enabled now the tunneled-node clients on same VLAN can communicate between each other.
Configuration:
To enable "local-proxy-arp":
Get to the interface of the VLAN on the controller
Example :
(config)#interface vlan 5
(config)#ip local-proxy-arp
To enable tunnel loop prevention on controller
(config)# tunnel-loop-prevention
Verification
Show commands:
To check if tunnel-loop-prevention is enabled or disabled
#show tunneled-node config
Tunnelded node Server: Enabled
Tunnel Loop Prevention: Enabled
To check if local-proxy-ap is enabled:
#show interface vlan 5
Look for in the output "ProxyARP enable"

streetfi8er wrote:
Server ready,waiting for client:
Exception in thread "New THREAD" java.lang.NullPointerException
at server4$server4Thread.run(server4.java:88)
Failed to accept client
when i run the second client programme on different a console in the same system i get the error that:
Unknown HostOK, I'm no socket programming expert; but I can see a few potential problems with what you've written.
1. First off, which line is line 88? Line numbers would be useful. Also, indenting your code properly would make it easier to read.
2. Your 'while(!str.equalsIgnoreCase("close"))' will always fail with a NullPointerException because 'str' is initially set to null.
3. Your 'while(true)' loop worries me. How does it exit? Relying on an exception is usually very bad practise.
4. You are not handling SecurityExceptions. While it's unlikely to happen on your machine; it could easily happen on another.
5. It might be worth indicating the actual exception thrown in your "Failed to accept client" message. accept() can throw three different types of IOException.
6. All the threads you create will be called "New THREAD", which doesn't provide much value.
HIH
Winston

How to make VPN client auto timeout when it still idle?

How to make VPN client auto disconnect when it still idle?
Hi,I found some user still connected the VPN evenif they dose not use the VPN resouse.
I try to set a "idle timeout" for the VPN configuration.
We use PIX515 8.0.3 and CISCO ACS 4.2 for the VPN's connection and authentication,and the user use cisco vpn client for the connection.
I have tried many methods,but all failured.
First,I configed "vpn-idel-timeout 5" on PIX.It can not worked.
so,I add Radius(CISCO VPN 3000/ASA/PIX 7.0+) attribute "[026/3076/050] Authenticated-User-Idle-Timeout" on CISCO ACS,It still not worked.
And I also add IETF RADIUS Attributes "[028] Idle-Timeout" on group setting on ACS,it always not worked.
i found in vpn client's statistics,it always has some byte sended or received, i thought it maybe IPsec keepalive message or Radius message.
This maybe the reason because the PIX or ACS think the vpn user is keep working.
Can someone tell me how to make a "idle time out"?
best regard.
Roger

here is the configuration on PIX,
group-policy DfltGrpPolicy attributes
wins-server value 10.0.0.67 10.0.0.68
dns-server value 10.0.0.67 10.0.0.68
vpn-simultaneous-logins 20
vpn-idle-timeout 5
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn-acl
default-domain value mydomain.com
address-pools value vpnpool group-policy DfltGrpPolicy attributes
wins-server value 10.0.0.67 10.0.0.68
dns-server value 10.0.0.67 10.0.0.68
vpn-simultaneous-logins 20
vpn-idle-timeout 5
split-tunnel-policy tunnelspecified
split-tunnel-network-list value vpn-acl
default-domain value want-want.com
address-pools value vpnpool

How do you copy, for example I work with blue prints and I want to copy a section and copy into another new page?

How do you copy, for example I work with blue prints and I want to copy a section and copy into another new page?

Forgot to add that it would be an adjustment layer with some kind of mask on it already. The mask is uncentered when copy and pasted which throws it off.
I guess the same question would go towards doing the same for an object. How to copy and paste it over to a new doc, keeping its position within the document? is this possible?

How to make your iPad and iPhone commicate with each other

How to make your iPad and iPhone commicate with each other

this is very easy...
firstly disconnect the DSL modem for the linksys..
then connect the computer to the linksys router (port 1/2/3/4)..
then access the linksys setup UI
open ur web browser
site: http://192.198.1.1/
username: [blank]
password: admin
now hook up the westell modem.. and goto the status page ...
check Internet IP.
if then Internet IP is 192.168.1.* then,
disconnect the westell from the router and goto the setup page.
change the LOCAL IP address to 192.168.2.1 (notice the 2.1 and not 1.1)
save settings....
connect the westell and viola ur online...
if the Internet IP is 0.0.0.0 then
goto the setup page and change the 'Internet connection Type' to 'PPPoE'
once done the page changes and give u a place to enter a username and a password.. this username and password is given by verizon..
sud be something like '[email protected]'
once done save settings...
goto the status page and hit connect... give it a few moments... u shud get a Internet ip address... if u get one ur online if not then power cycle the entire network. and try check to see if u get an ip..
hope this helps...
cheers..
Life is short... So get movin !!!
DopeLorD

Has anyone figured out how to make the Yamaha 01V96i mixer work with Logic 9.1.8

Has anyone figured out how to make the Yamaha 01V96i mixer work with Logic 9.1.8 as a control surface ?

In YAMAHA01v96i:
Go to DIO/SETUP select Generic DAW. Go to MIDI settings page and set the desired port (personally I use Number 1), Select the same audio frequency you use in your DAW (I use 44.1KhZ)...at this point You should save a scene in you 01V96i to avoid to repeat all the procedure again.
Open studio manager, go to patch and set the input port from 17 to 32 respectively to USB1-USB16 (this will give you the return from you DAW to the 01v96i
Save again the scene overwriting the old one.
in LOGIC
Click on preferences, select Audio then select 01v96i, then click on control surface and select Mackie design Baby HUI and in the midi session set the same port that you've been setting on the Yamaha 01V96i (Port 1 if you follow this example).
That's more or less it.
It worked for me...so far

Hello, i would like to know how to make horizontal sites and it moves with the scroll

Hello, i would like to know how to make horizontal sites and it moves with the scroll

Hi
You can refer to these videos :
http://www.lynda.com/Muse-tutorials/basics-horizontal-scrolling-websites/108131/115685-4.h tml
https://www.youtube.com/watch?v=gZI_K1TXqOM
Thanks,
Sanjit

Is there a mobile phone that can sync with ical, but does not require a data plan?

Is there a mobile phone that can sync with ical, but does not require a data plan?

Thanks for the reply. I already have this info, but have spent several hours trying to cross reference with the product descriptions and the different carriers websites. I was hoping there was an easier way.
John Maisey wrote:
Hi,
You cakn sync many phones using iSync. See here: http://support.apple.com/kb/ht2824
Best wishes
John M

My i message seems that is working with everyone but with a particular phone is not?, My i message seems that is working with everyone but with a particular phone is not?

My I message is working with everyone BUT with one phone, Same thong happen with this other phone i message works with everyone else but with me What did i did?

Actually she does, her i message is working with everyine else but me, and viceversa

HT201364 I upgraded my MacBook Pro with Lion (but with iphoto 9.2.1) to Maverick and now I can't open iphoto and I can't update either

I upgraded my MacBook Pro with Lion (but with iphoto 9.2.1) to Maverick and now I can't open iphoto and I can't update either - can anyone help please?

Download the iPhoto upgrade from the App Store. It should be free.
iWork and iLife for Mac come free with every new Mac purchase. Existing users running Mavericks can update their apps for free from the Mac App Store℠. iWork and iLife for iOS are available for free from the App Store℠ for any new device running iOS 7, and are also available as free updates for existing users. GarageBand for Mac and iOS are free for all OS X Mavericks and iOS 7 users. Additional GarageBand instruments and sounds are available for a one-time in-app purchase of $4.99 for each platform.

How to make the Profit Center Field Mandatory in Cost center Master Data

Dear All,
Please let me know how to make the Profit Center Field mandatory in Cost Center Master Data as well as my Internal Order Master Data?
Thanks in advance!
Regards,
Rajeswari Shankar.

Hi Rajeswari,
You can modify message number KS096 to "Error" via OBA5. Thus, the users would no be able to save a cost center without entering a profit center. (Depending on your release you can make KS096 modifiable by implementing note 486781.)
Concerning the internal orders (transaction KO01), you can run KOT2 and set Profit center field as required entry in "change field selection" section.
Regards,
Greta

My brother locked his mac with Icloud, but there is no apple store where he lives. what he can do?

my brother locked his mac with Icloud, but there is no apple store where he lives. what he can do?

He will have to go to an Apple Store or an Apple-authorised repair centre, and he will need the invoice for the Mac so that he can prove it's his.

I have a maginon film scanner bought from ALDI. It works with windows but with OSX Maverick software it keeps crashing as soon as I try and capture an image. I cannot find details of software updates anywhere.

I have a maginon film scanner bought from ALDI. It works with windows but with OSX Maverick software it keeps crashing as soon as I try and capture an image. I cannot find details of software updates anywhere.

Same question answered here : https://discussions.apple.com/thread/5762314?tstart=0
I just popped in with using Mavericks (I got rid of my MBP about a year ago, and just got another one when I got an Air for my wife) and noticed that Mavericks is not working and playing well with a couple of programs I already owned (Paraellels, for example...yes, I spelled it wrong...). I looked for maginon.com and it didn't exist, nor was my google search directed to another location for them, so I postulate that the device may not be in production anymore, thus: no driver updates from the manufacturer.
From my mac-noob-layman's perspective: get some vmware, run windows and use the scanner in your virt machine to capture your images. Put the images in your mac side and work your mac magic on them there.
Peace

Help, how to make Finder to refresh custom icon programmatically

Hi
I have two file both are same name, e.g. 1.rtf, but with different custom icon.
When I copied the first 1.rtf to an USB drive, the custom icon was displayed correctly.
However, when copied the second file to the USB drive to replace the first file, Finder still showed the custom icon of the first file.
How can I solve this issue and how can I make Finder to refresh the custom icon programmatically.
Thanks

Hi KT, thanks your reply & help
but result is same. The following is my experiment
STEP 1: copy 1.rtf to USB drive, the result is OK.
STEP 2: copy another 1.rtf to USB drive, Finder still showing the 1st file icon and a little bit blurred
STEP 3: copy 3rd file without custom icon, the result is OK
STEP 4: using following code to set its custom icon, the result is still show the custom icon of the 1st file
[[NSWorkspace sharedWorkspace] setIcon:image forFile:[filePath stringValue] options:nil];
It seems that Finder will has some cache to store file's custom icon. If use "Force Quit" to relaunch Finder, it become correct but how can I use program code to refresh it without "Force Quit"?

How to make copy client with customizing but with no deleting appl.data

Similar Messages

Maybe you are looking for