How to put the phone to original manufacture out o...
Is there a way to bring the n900 back to the out of the box look ( i tried the settings/restore original settings) it just do a reset. i need to delete every thing and bring it back to the original look.As if i have Windows installed on a hard disk then we do a full fresh installation on the computer?
Will using the nokia update software and reinstall the software will do the trick
Thanks
Solved!
Go to Solution.
check this link, long process for N900
https://wiki.maemo.org/Updating_the_firmware
Windows [edit] N900 (XP) MS Windows users willing to update the N900 can use the Nokia Software Updater or see the Flasher documentation.
It is also possible to flash the N900 directly without using the Nokia Software Updater (NSU). This is handy when you would like to flash the device with the same firmware that is already installed on the N900. The NSU will update only if there is a version newer than the one installed on the device.
To flash direcly from the XP command line, follow these steps:
Download and install the latest version of Flasher (e.g. maemo_flasher-3.5_2.5.2.2.exe).
Download the latest firmware (.bin) file and save to 'c:\Program Files\maemo\flasher-3.5\'
Fully charge the battery.
Unplug charger and switch off the device.
Open the command prompt on XP. Start + Run. Type cmd and press Enter.
Change directory to the flasher program
cd "c:\Program Files\maemo\flasher-3.5"
Connect the USB cable while pressing 'u' key on the N900 (details on the wiki)
Run the following command:
flasher-3.5.exe -F RX-51_2009SE_1.2009.42-11_PR_COMBINED_MR0_ARM.bin -f -R
The update will take about 4 minutes after which the N900 will reboot and display the Welcome screen with Regional settings.
good luck....
Similar Messages
-
My iPhone has a protective cover on it and I carry it in my pocket a lot. Quite often when I take it out of my pocket the silent/ring switch is off and I am sure it was on when I put the phone in my pocket. How can this be happening?
Protective cover as in screen protector? This would have nothing to do with the silent switch.
If you're referring to an actual case though... take the case off and see if the problem continues.
It may be as simple as the silent switch being lose, which will require a device replacement to resolve. -
Iphone would not restore---- Error -50. I have tried to restore, and it restored it to the new point that it created after 5.0 was installed. How can I get it an older restore point from my backups and restore it on another computer? The phone has been wiped out. I can see earlier backups in my C:\Documents and Settings\user\Application Data\Apple Computer\MobileSync\Backup folder. There are four subfolders in this address. I need my contacts, photos, and messages back. I know this is a common error but I can not figure it out. I have ran the other troublshoot items in the error steps for 13 and 14 like apple says. Is there a way to call apple and get a step by step of how to restore from another restore point? Does anybody have a solution????
It tells you to go to Error 13 and 14 if you receive error (-50).
Here is what I have tried...
Error 13 and 14: These errors are typically resolved by performing one or more of the steps listed below:
Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting. I have moved it around to different ports.
Put a USB 2.0 hub between the device and the computer. Didn't change anything.
Try a different USB 30-pin dock-connector cable.
Eliminate third-party security software conflicts. Removed all virus protection and firewall.
There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. Or, follow this article by Microsoft: How to reset Internet Protocol (TCP/IP) to reset the packet size back to the default for Windows.Used the Microsoft fix it.
Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online. Doesn't matter.
Try to restore from another known-good computer and network. I do not know how to do this or how to find the correct/full/complete restore point. There should be more information for this. -
I just updated to iOS 7 and now my iMessages won't work. It just keeps saying activating iMessage but it's not doing anything; I tried signing in with my Apple ID but then it just lets me send them using my email address and the number the phone was originally set to; even though that is not my actual number that I use as I changed it through Vodafone so the SIM card now has a different number.
It won't even let me click on my number to select it; it is just that faded grey colour and there are no ticks by it;
And when it says "may be a standard SMS charge to activate" I'm not even getting a text through to be able to activate it anyway
How can I fix this?http://theunlockr.com/2013/07/12/how-to-stop-your-email-from-showing-up-in-imess age-video/
-
How to put the file name in notepad file
dear frank,
how to put the file name in notepad file via power shell. I mean i want to put the file name in that notepad file
for example,
my file name is ABL and in this file data is
02/06/2015,180.00,182.00,176.01,180.50,1575500
02/06/2015,4.20,4.20,4.20,4.20,500
02/06/2015,113.50,113.70,112.91,113.09,157800
02/06/2015,682.01,695.90,682.00,683.19,4250
02/06/2015,213.98,215.00,213.00,214.87,326200
02/06/2015,21.52,21.65,21.52,21.60,4000
02/06/2015,111.00,111.25,108.25,108.91,17100
02/06/2015,52.00,52.00,52.00,52.00,500
and i want to data in this form
ABL,02/06/2015,180.00,182.00,176.01,180.50,1575500
ABL,02/06/2015,4.20,4.20,4.20,4.20,500
ABL,02/06/2015,113.50,113.70,112.91,113.09,157800
ABL,02/06/2015,682.01,695.90,682.00,683.19,4250
ABL,02/06/2015,213.98,215.00,213.00,214.87,326200
ABL,02/06/2015,21.52,21.65,21.52,21.60,4000
ABL,02/06/2015,111.00,111.25,108.25,108.91,17100
ABL,02/06/2015,52.00,52.00,52.00,52.00,500
There are many file like this that i want to be edit
plese tell me how can i do it, i think it is possible via windows power shell.
thanks in advance.Hi
Just for completeness, what version of VB.NET are you using?
Here is a complete project to copy all the files with the added "ABL," at the start of each line. You need to start a new Project with a BLANK default Form1, and replace all of Form1 code with the code below. When you run this project, you
need to use the 2 buttons to set up the ORIGINAL file folder and a folder to place the copies. You need to check if the file EXTENSION is correct (I assumed txt), and check the text to add to each line is correct. Once all is set up you should have a
big red button to start the operation.
NOTE: it is important that you try this out on a copy of some of the files to verify accuracy BEFORE trying on original files. Make sure you have a good back up of the original files before doing anything else.
' new project with default BLANK Form1
' replace all Form1 code with this code
' WARNING: make sure you have a backup of
' any files you use this application to
' operate on.
Option Strict On
Option Infer Off
Option Explicit On
Public Class Form1
Dim OrigFileFolderPath As String = Nothing
Dim CopyToFolderPath As String = Nothing
Dim lab1, lab2, lab3 As New Label
Dim tb1, tb2, tb3 As New TextBox
Dim b1, b2, b3, b4 As New Button
Dim fb As New FolderBrowserDialog
Dim bgw As New System.ComponentModel.BackgroundWorker
Private Sub Form1_Load(sender As Object, e As EventArgs) Handles Me.Load
Me.Size = New Size(731, 300)
With lab1
.Text = "Original Files Folder Path"
.Location = New Point(15, 5)
End With
With tb1
.Width = 560
.Location = New Point(10, 30)
.BackColor = Color.Khaki
.ForeColor = Color.Maroon
.Font = New Font(Me.Font.FontFamily, 12)
.BorderStyle = BorderStyle.FixedSingle
.Anchor = AnchorStyles.Top Or AnchorStyles.Left Or AnchorStyles.Right
End With
With lab2
.Text = "Copy Files to Folder Path"
.Location = New Point(15, 125)
End With
With tb2
.Width = 665
.Location = New Point(10, 150)
.BackColor = Color.Khaki
.ForeColor = Color.Maroon
.Font = New Font(Me.Font.FontFamily, 12)
.BorderStyle = BorderStyle.FixedSingle
.Anchor = AnchorStyles.Top Or AnchorStyles.Left Or AnchorStyles.Right
End With
With lab3
.Text = "File Ext"
.Location = New Point(600, 5)
.Anchor = AnchorStyles.Top Or AnchorStyles.Right
End With
With tb3
.Text = ".txt"
.Width = 80
.Location = New Point(590, 30)
.BackColor = Color.Khaki
.ForeColor = Color.Maroon
.TextAlign = HorizontalAlignment.Center
.Font = New Font(Me.Font.FontFamily, 12)
.BorderStyle = BorderStyle.FixedSingle
.Anchor = AnchorStyles.Top Or AnchorStyles.Right
End With
With b1
.Text = "Choose Original Files Folder Path"
.AutoSize = True
.Location = New Point(10, 65)
End With
With b2
.Text = "Choose Copy Files to Folder Path"
.AutoSize = True
.Location = New Point(10, 185)
End With
With b3
.Text = "DO THE COPY"
.AutoSize = False
.Size = New Size(240, 50)
.BackColor = Color.Red
.ForeColor = Color.White
.Font = New Font(Me.Font.FontFamily, 20, FontStyle.Bold)
.Location = New Point(420, 80)
.Anchor = AnchorStyles.Top Or AnchorStyles.Right
.Visible = False
End With
With b4
.Text = "CANCEL JOB"
.AutoSize = False
.Size = New Size(240, 50)
.BackColor = Color.Red
.ForeColor = Color.White
.Font = New Font(Me.Font.FontFamily, 20, FontStyle.Bold)
.Location = New Point(420, 80)
.Anchor = AnchorStyles.Top Or AnchorStyles.Right
.Visible = False
End With
Me.Controls.AddRange({lab1, lab2, lab3, tb1, tb2, tb3, b1, b2, b3, b4})
With bgw
.WorkerReportsProgress = True
.WorkerSupportsCancellation = True
End With
AddHandler bgw.DoWork, AddressOf bgw_DoWork
AddHandler bgw.RunWorkerCompleted, AddressOf bgw_Completed
AddHandler b1.Click, AddressOf b1_Click
AddHandler b2.Click, AddressOf b2_Click
AddHandler b3.Click, AddressOf b3_Click
AddHandler b4.Click, AddressOf b4_Click
End Sub
Private Sub b1_Click(sender As Object, e As EventArgs)
fb.SelectedPath = My.Computer.FileSystem.SpecialDirectories.MyDocuments
fb.ShowNewFolderButton = False
Dim r As DialogResult = fb.ShowDialog
If r = Windows.Forms.DialogResult.OK Then
tb1.Text = fb.SelectedPath
If IO.Directory.Exists(tb1.Text) AndAlso IO.Directory.Exists(tb2.Text) AndAlso Not (tb1.Text = tb2.Text) Then
If tb3.Text = Nothing Then
redo: tb3.Text = InputBox("Enter the file extension that you want to copy/change", "FILE EXTENSION")
If tb3.Text = Nothing Then GoTo redo
End If
b3.Visible = True
Else
b3.Visible = False
End If
End If
End Sub
Private Sub b2_Click(sender As Object, e As EventArgs)
fb.SelectedPath = My.Computer.FileSystem.SpecialDirectories.MyDocuments
fb.ShowNewFolderButton = True
Dim r As DialogResult = fb.ShowDialog
If r = Windows.Forms.DialogResult.OK Then
tb2.Text = fb.SelectedPath
If IO.Directory.Exists(tb1.Text) AndAlso IO.Directory.Exists(tb2.Text) AndAlso Not (tb1.Text = tb2.Text) Then
If tb3.Text = Nothing Then
redo: tb3.Text = InputBox("Enter the file extension that you want to copy/change", "FILE EXTENSION")
If tb3.Text = Nothing Then GoTo redo
End If
b3.Visible = True
Else
b3.Visible = False
End If
End If
End Sub
Private Sub b3_Click(sender As Object, e As EventArgs)
b3.Visible = False
b4.Visible = True
If Not tb3.Text.StartsWith(".") Then tb3.Text = "." & tb3.Text
bgw.RunWorkerAsync()
End Sub
Private Sub b4_Click(sender As Object, e As EventArgs)
bgw.CancelAsync()
End Sub
Private Sub ReadPWFile(fn As String)
Dim filename As String = My.Computer.FileSystem.GetName(fn)
Dim barename As String = IO.Path.GetFileNameWithoutExtension(fn)
Dim copyto As String = tb2.Text & "\" & filename
Dim line As String = Nothing
Dim lines As New List(Of String)
Using sr As IO.StreamReader = New IO.StreamReader(fn)
Do
line = sr.ReadLine()
If Not line = Nothing Then
lines.Add(barename & "," & line)
End If
Loop Until line = Nothing
End Using
Using sw As IO.StreamWriter = New IO.StreamWriter(copyto)
For Each s As String In lines
sw.WriteLine(s)
Next
End Using
End Sub
Private Sub bgw_DoWork(sender As Object, e As System.ComponentModel.DoWorkEventArgs)
Dim ftc As Collections.ObjectModel.ReadOnlyCollection(Of String) = My.Computer.FileSystem.GetFiles(tb1.Text)
For Each f As String In ftc
If bgw.CancellationPending Then
e.Cancel = True
Exit For
End If
Dim ex As String = My.Computer.FileSystem.GetFileInfo(f).Extension.ToLower
If My.Computer.FileSystem.GetFileInfo(f).Extension.ToLower = tb3.Text.ToLower Then
ReadPWFile(f)
End If
Next
End Sub
Public Sub bgw_Completed(sender As Object, e As System.ComponentModel.RunWorkerCompletedEventArgs)
tb1.Text = Nothing
tb2.Text = Nothing
b3.Visible = False
b4.Visible = False
MessageBox.Show("Finished copying files", "Job Completed")
End Sub
End Class
Regards Les, Livingston, Scotland -
How to deactivate the phone?
I want to give my iPhone to a relative. I would like to leave it relatively untouched, and just deactivate the phone so she can activate it for herself. How can I do this?
If it can't be done with just the phone part, how can I reset the phone to original and keep it with the 1.1.4 software?Just pull your SIM card out. She just need to get a new SIM card to open a new account for herself. You can do a restore if you want to wipe it clean.
Dave M.
MacOSG Founder/Ambassador An Apple User Group iTunes: MacOSG Podcast
Creator of 'Mac611 - Mobile Mac Support' (designed exclusively for an iPhone/iPod touch) -
How to remove the IT policy from my Torch 9800, or how to reset the device to original setting
I have a Torch 9800 formerly- used for business emails. According to our company policy there was an IT policy installed to the device hence would force the user to set password protecting the device.
Now this device has been retired and I like to use it only for regular phone calls thus do not like to have a password protection. My question is:
How to remove the IT policy from the device?
or
How to reset the device to original setting?
I have been trying to swipe and scrub the device several times but that IT policy still exist. Need help......
Solved!
Go to Solution.See the RIM Knowledge Base article here for information on how to remove an IT Policy. See the Method Three in the link:
KB14202 How to remove an IT policy from a BlackBerry smartphone
Read this RIM Knowledge Base article to reset your device to the factory settings.
KB18998 How to reset a BlackBerry smartphone to factory defaults
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
Can I pair my iPhone and iPad so I can put the phone in my bag and take calls threw the iPad like the new ASUS tablet/phone combo ?
As a Quadriplegic I keep dropping my mouth stick on the ground and I fumble for my phone when it rings the table on my wheelchair is cluttered with my iPad iPhone mouth stick and TV and AC remotes I want to be able to put my iPhone in my bag and receive calls threw the iPad.
All new electric wheelchairs allow you to pair the joystick or chin control of the chair to only one device so currently you have to sacrifice your use of one to use the other if we can pair the iPhone and iPad by wifi we can then sit the iPad in a mount on our wheelchairs and pair it ia bluetooth and operate them with ease .
Can anyone out there help me or pass on my needs to a development team within Apple, please help as I don't want to have to buy the ASUS tablet/phone
PaulI would like to be able to do this also but, i'm not sure how to set my iPad to manually sync for one thing and also, when I connect my iPad to my new (recently purchased,first time,new to this) iMac it only gives me the option to either set up as 'new' or 'restore to my recent iPhone back up'. I just want them to be separate. How can I fix this please?
-
A computer illiterate friend created 3 accounts on his iPhone 5 but forgot the passwords. He can't reset the password as his yahoo address is no longer valid. Erasing the phone doesn't solve the issue as the Apple server identifies the hardware as registered. How to register the phone with Apple?
I helped him create a new email address and new iCloud account on my Mac but when we try to register the phone with Apple it says: Maximim accounts limit reached for this device. How can he register the phone? I read different threads and found out that only Apple care can do that. We're in Romania and don't know where to call. Any suggestions on how we fix this?When I checked the support site for Romania, you apparently don't have an Apple Care contact center. You "may" try calling the US Apple care number to verify the account and have the password reset sent to a different email address. 800-694-7466
-
i have an ipod touch and i put cds on itunes onmy computer , but i cant figure out how to put the music from the cds on my ipod touch can anyone help me?
ok i select th e music from my music libary and go to file and click sync to my ipod and when it gets to step 3.. it says waiting for changes to be made.. yes the songs play on the itunes .. and no it wasnt the same computer i used last time
-
How to put the form in Query mode
Hello
Please let me know how to put the form or block in Query mode , so that when i run the form it should be in Query mode . I have seen properties of SET_FORM_PROPERTY and SET_BLOCK_PROPERTY but cannot find one
ThanksQUERY mode? Did you mean, that you can only QUERY without changing data.
This is the QUERY-ONLY-mode, which can be started e.g. call_form
this is the help for that topic:
PROCEDURE CALL_FORM
(formmodule_name VARCHAR2,
display NUMBER,
switch_menu NUMBER,
query_mode NUMBER,
data_mode NUMBER,
paramlist_name VARCHAR2);
query_mode
NO_QUERY_ONLY (The default.) Form Builder will run the indicated form in normal mode, allowing the end user to perform inserts, updates, and deletes from within the called form.
QUERY_ONLY Form Builder will run the indicated form in query-only mode, allowing the end user to query, but not to insert, update, or delete records. -
my ipod touch 2g is on black screen.when i connect it to my pc it is not recognizing it.then i opened i tunes and put the phone in dfu mode it says an ipod is detected but it cannot be restored error 1600.plz help me...
Error 1604
This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
Restore and wait for the error.
When prompted, click OK.
Close and reopen iTunes while the device remains connected.
The device should now be recognized in Recovery Mode again.
Try to restore again.
If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
Error 1600, 1601, 1602
Follow the steps listed above for Error 1604. This error may also be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software. -
Visa has changed for the purchase of Apple products, i did not know how I put the new MasterCard number to finish the process of buying products Thank you
i have ibad mini
and iphone4
laptop sony
can you sent for me the anserChanging Account Information > http://support.apple.com/kb/HT1918
-
I just purchased an Apple TV. I have a pc running windows 7. It is connected to a router and the router is connected to a wireless router. I connect my iPhone, iPad and apple tv to wireless network but do not know how to put the pc on the wifi network so the Apple TV can do home share.
I don't mean to be facetious but sometimes the simplest things are overlooked. To connect to your library you have to have the computer where the iTunes library is located running and with iTunes open. It also needs to be on the same network. My network is dual band and works with either stream but a friend of mine does not. He has to set the computer and the Apple TV to the same band. Hope this helps.
-
How to put the current timer in the frame
I am doing one application and i am using frame. I want to show the current time( hour and minute). But i don't know how to implement it. Please help me to solve my problem. Below is the sample code of my program. How to put the timer in the bottom part.
//AdminMenu.java
import java.io.*;
import javax.swing.*;
import java.awt.event.*;
import java.awt.*;
public class AdminMenu extends JFrame{
private JLabel lblmenu;
private JLabel lblvideo;
private JLabel lbladmin;
private JButton cmdaddvideo, cmddeletevideo, cmdeditvideo;
private JButton cmdaddadmin, cmddeleteadmin, cmdchangepass;
private Container c;
private GridBagLayout gdlayout;
private GridBagConstraints gdconstraints;
private Color colorValues[] =
{ Color.black, Color.blue, Color.red, Color.green };
public AdminMenu()
super("Administration Menu");
JMenu fileMenu = new JMenu( "File" );
fileMenu.setMnemonic( 'F' );
JMenu openMenu = new JMenu ("Open");
openMenu.setMnemonic('O');
fileMenu.add( openMenu );
JMenuItem exitItem = new JMenuItem( "Exit" );
exitItem.setMnemonic( 'x' );
exitItem.addActionListener(
new ActionListener() {
public void actionPerformed( ActionEvent event )
System.exit( 0 );
} // end anonymous inner class
); // end call to addActionListener
fileMenu.add( exitItem );
// create menu bar and attach it to MenuTest window
JMenuBar bar = new JMenuBar();
setJMenuBar( bar );
bar.add( fileMenu );
setSize(300,250);
setLocation(350,200);
this.setResizable(true);
show();
//---------------------- Main -------------------------------
public static void main(String args[])
AdminMenu app = new AdminMenu();
app.setDefaultCloseOperation(
JFrame.EXIT_ON_CLOSE );
Thanks for helping mee.g. use a thread that invokes new Date() (every minute), format the Date with SimpleDateFormat and print the result String on a Label that you can put on your frame ...
Maybe you are looking for
-
Using SUBMIT in an ABAP program.
Hello, There is a need in my function module where I need to take the help of a transaction wherein I would require the values of an internal table ( which is populated somewhere in the transaction program ) to be passed back to my function module wh
-
Imac won't recognize Pyro A/V converter box
I can't seem to get my G-4 imac to recognize my Pyro A/V convertor box to use for importing analog video. I've tried resetting power, unplugging cables, etc. I'm pretty new to mac, so could someone help me with this?
-
Hy dear! My Iphone 5s doesn't work. When i power on appear searching the sim card, but doesn't connect to the operator. Who can help me? I reset the Iphone, but doesn't fix the probem. Thanks
-
Html on Jlabel font size varies
Hi, I am trying to put html text on JLabel with different font sizes. The font size reflected on JLabel is different from the font size on swing components. eg. Font size xx large on JLabel with html is looking very different from font size xx large
-
Add search help to a field of standard infotype
Hi, I need to add a search help in infotype 0591(Nominations), column relation which falls in the Nomination table control. Please guide me on how should I go ahead. Regards, Jaya