How to replace Nexus5596 with dual-homing N2K
What is the correct process to replace a FEX parent switch with dual-homing fex?
Traffic should not be interrupted.
Hi
Do you have VPC between Parent Switches & are you running VPC on dual homed FEX fabric ports. ?
If yes Below is the procedure,
1) boot the replacement switch without VPC, peer-links & FEX ports connected to it.
2) Make sure it has same Software version matches with the peer switch.
3) enable Pre-Provisioning for slots with appropriate FEX model.
, here find the guide:
http://www.cisco.com/en/US/partner/docs/switches/datacenter/nexus5000/sw/system_management/521_n1_1/b_5k_System_Mgmt_Config_521N11_chapter_0100.html#task_05BB53AD7AFB49CF9A8E4A5C6C37CB38
So, on the replacement switch you will pre-provision the Fabric Extender and configure the ports so it will be ready when you add the module to the RMA SW.
Please make sure you put the appropriate FEX model on the provision slot, otherwise, when connected it will not come Online
Example, FEX 110:
N5K(config)# slot 110
N5K(config-slot)#provision model N2K-C2248T
4) Now keep all ports at Shut down state Then Configure Entire switch that includes FEX host ports, FEX Fabric Ports & VPC peer-link, VPC Domain Configuration.
keep FEX host ports in shut state.
5) keep VPC Role priority on existing switch lower than , new switch
6) Connect Peer-link ports to Peer switch & wait till VPC Comes up-
7) Then connect Fabric ports from FEX to the pre-configured ports on replacement switch
After it comes online Unshut FEX host ports.
I got similar steps here as well
http://www.cisco.com/en/US/docs/switches/datacenter/nexus5000/sw/operations/n5k_vpc_ops.html#wp425197
NOTE: I followed same process however, few ping drops were seen....arnd ( 5- 6 ping loss) only on few hosts...
Mazhar
Similar Messages
-
How to replace MobileMe with ICloud on my Imac?
how to replace MobileMe with ICloud on my Imac? pleae help. Other devices (Ipad and Iphone) are Iclouded but I can't change MobileMe in my system preferences on IMac (10.6.8)
SylwiaYou need to upgrade the computer's OS. Open the Mac App Store and try downloading Mavericks. If you get told it's incompatible, choose About this Mac from the Apple menu, check if the computer has at least a Xeon or Core 2 Duo(not Core Duo) CPU and 2GB of RAM, and if it does, click here and order a download code for Lion 10.7.
Back up your data before upgrading. Mac OS X 10.7 and newer don't support PowerPC programs such as versions of Microsoft Office prior to 2008.
(103507) -
How to replace number with flexible length
Hi..
Could somebody help me, how to replace any number start with more than 2 digits of "0" become 2 digits "0" only. As example:-
Sample Result
123456789 => 123456789
0123456789 => 0123456789
00123456789 => 00123456789
000123456789 => 00123456789
0000123456789 => 00123456789
00000123456789 => 00123456789
Thank you,
BaharinOr - to handle the situation when '00' is also in between the word:
SQL> with t as (
select '12300456789' str from dual union
select '0123456789' from dual union
select '00123456789' from dual union
select '000123456789' from dual union
select '0000123456789' from dual union
select '00000123456789' from dual
select str,
decode(substr(str,1,2),'00', '00' || ltrim(str,'0'),str) new_str
from t
STR NEW_STR
00000123456789 00123456789
0000123456789 00123456789
000123456789 00123456789
00123456789 00123456789
0123456789 0123456789
12300456789 12300456789
6 rows selected. -
How to replace sapdba with brtools after upgrade database to 10.2
All,
I have update our database to oracle 10.2,my brtools version is 7.0 now ,
but can't run analyze table and dbcheck in db13,
seems to still use SQLDBA when run analyze table and dbcheck.
please refer to the below informations.
Detail log: 0810080300.aly
***** SAPDBA - SAP Database Administration for ORACLE *****
SAPDBA V6.10 Analyze tables
SAPDBA release: 6.10
Patch level : 1
Patch date : 2001-05-25
ORACLE_SID : PRD
ORACLE_HOME : /oracle/PRD/102_64
ORACLE VERSION: 10.2.0.2.0
Database state: 'open'
SAPPRD : 46C
SAPDBA DB USER: (-u option)
OS login user : prdadm
OS eff. user : prdadm
SYSDBA priv.: not checked
SYSOPER priv.: not checked
Command line : sapdba -u / -analyze DBSTATCO
HOST NAME : sapprd1
OS SYSTEM : HP-UX
OS RELEASE : B.11.31
OS VERSION : U
MACHINE : ia64
Log file : '/oracle/PRD/sapcheck/0810080300.aly'
Log start date: '2008-10-08'
Log start time: '03.00.09'
----- Start of deferred log ---
SAPDBA: Can't find the executable for SQLDBA/SVRMGR. Please, install one of
them or enter one of them in the SAPDBA profile (parameter
sqldba_path).
(2008-10-08 03.00.06)
SAPDBA: Error - running temporary sql script
'/oracle/PRD/sapreorg/dbacmd.sql' with contents:
CONNECT /******** AS SYSDBA
SAPDBA: Couldn't check SYSDBA privilege.
SAPDBA: Can't find the executable for SQLDBA/SVRMGR. Please, install one of
them or enter one of them in the SAPDBA profile (parameter
sqldba_path).
(2008-10-08 03.00.06)
SAPDBA: Error - running temporary sql script
'/oracle/PRD/sapreorg/dbacmd.sql' with contents:
CONNECT /******** AS SYSOPER
SAPDBA: Couldn't check SYSOPER privilege.
----- End of deferred log ---
Analyze parameters:
Object: All tables in table DBSTATC ( for DB optimization run )
Method: E ( Default )
Option: P10 ( Default )
Time frame: 100 hours
Refresh : All objects
Option: DBSTATCO ( for the DB optimizer: Tables with Flag DBSTATC-TOBDO = 'X' )
** Refresh Statistics according control table DBSTATC **
Total Number of Tables in DBSTATC to be analyzed: 170
Number of Tables with forced statistics update (ACTIV = 'U'): 0
SAPDBA: SELECT USER# FROM SYS.USER$ WHERE NAME='SAPPRD'
ORA-00942: table or view does not exist
(2008-10-08 03.00.09)
SAPDBA: Error - getting size of segment 'SAPPRD.D010INC'
SAPDBA: Error - during table analysis - table name: ->D010INC
SAPDBA: No tables analyzed ( No entries in DBSTATC with TOBDO = X or errors ).
SAPDBA: 0 table(s) out of 170 was (were) analyzed
Difference may be due to:
- Statistics not allowed ( see DBSTATC in CCMS )
- Tables do not exist on database and were skipped
Detailed summary of Step 1:
Number of Tables that needed new statistics according to DBSTATC: 1
Number of Tables marked in DBSTATC, but non-existent on the Database: 0
Number of Tables where the statistics flag was resetted: 0
******* Creating statistics for all tables without optimizer statistics *******
SAPDBA: Using control table DBSTATC
for taking optimizer settings into account
SAPDBA: 0 table(s) without statistics were found.
SAPDBA: 0 table(s) ( out of 0 ) was (were) analyzed/refreshed.
0 table(s) was (were) explicitely excluded or pool/cluster table(s).
SAPDBA: 0 index(es) without statistics was (were) found.
SAPDBA: 0 index(es) ( out of 0 ) was (were) analyzed/refreshed.
0 index(es) was (were) explicitely excluded or pool/cluster indexe(s).
SAPDBA: 157 table statistics from 157 tables were dropped.
They are either explicitely excluded in DBSTATC,
or R/3 Pool- or Cluster- tables
that must not have CBO Statistics
SAPDBA: The whole operation took 10 sec
SAPDBA: Step 1 was finished unsuccessfully
SAPDBA: Step 2 was finished successfully
Date: 2008-10-08
Time: 03.00.19
*********************** End of SAPDBA statistics report ****************
How to replace sapdba by brtools?please give me support,thanks.
Best Regards,
Mr.chen> I have update our database to oracle 10.2,my brtools version is 7.0 now ,
> but can't run analyze table and dbcheck in db13,
> seems to still use SQLDBA when run analyze table and dbcheck.
Yes, it does so, because somebody forgot to upgrade the BASIS SP as well...
What BASIS SP are you using?
regards
Lars -
How to replace numbers with text in tax return pdf using Adobe Acrobat X Pro
How do I replace numbers with text in tax return pdf using Adobe Acrobat X Pro? The tax return was created using CCH software. Thanks for your review.
Thanks Bill for your quick reply. CCH software is one of the major
suppliers of tax return software. I found an internal source that helped me
make the changes from numbers to text i.e. "$123,456" to "See Schedule O".
I am not sure if I am working in form or final text. Thanks again! Kelly -
ADF mobile: how to create graph with dual Y axis?
Hi,
Jdev 11.1.2.3.0 + mobile extension.
I try to figure out how to create a dvtm:comboGraph with dual Y axis but without success.
All series are rendered on the Y1 axis. Y2 axis even does not appear in the graph.
here my code:
<dvtm:comboChart var="row" value="#{bindings.lmrgGraph1.collectionModel}"
id="cc1" timeAxisType="enabled">
<amx:facet name="dataStamp">
<chartDataItem group="#{row.timeStamp}" value="#{row.acetat}"
series="#{lmrgGraphBundle.ACETAT}">
<!--dvtm:referenceObject color="ff0000" displayInLegend="on"
lineValue="#{bindings.graphTresholdAcetat.inputValue}"
lineWidth="2"/-->
</chartDataItem>
<chartDataItem group="#{row.timeStamp}" value="#{row.plannedMachines}"
series="#{lmrgGraphBundle.BMPLAN}"/>
<chartDataItem group="#{row.timeStamp}" value="#{row.actualMachines}"
series="#{lmrgGraphBundle.BMACTUAL}"/>
</amx:facet>
<dvtm:legend position="end" id="l1">
<dvtm:legendSection id="ls1" title="Legend"/>
</dvtm:legend>
<dvtm:yAxis axisMaxValue="#{bindings.maxYAxisValueAcetat.inputValue}"
title="#{lmrgGraphBundle.MENGE}">
<dvtm:majorTick/>
</dvtm:yAxis>
<!--dvtm:y2Axis majorIncrement="1.0"
title="#{lmrgGraphBundle.BETRIEBSMITTEL}"
axisMaxValue="#{bindings.maxYAxisValueMachines.inputValue}"-->
<dvtm:y2Axis majorIncrement="1.0"
title="#{lmrgGraphBundle.BETRIEBSMITTEL}"
axisMaxValue="10">
<dvtm:majorTick/>
</dvtm:y2Axis>
<amx:facet name="seriesStamp">
<dvtm:seriesStyle assignedToY2="false" color="0052ff" lineWidth="2"
rendered="#{(row.series eq lmrgGraphBundle.ACETAT)}"
series="#{row.series}"/>
<dvtm:seriesStyle assignedToY2="true" color="e7e700" lineWidth="10"
rendered="#{(row.series eq lmrgGraphBundle.BMPLAN)}"
type="bar" series="#{row.series}"/>
<dvtm:seriesStyle assignedToY2="true" color="94f700" lineWidth="10"
rendered="#{(row.series eq lmrgGraphBundle.BMACTUAL)}"
type="bar" series="#{row.series}"/>
</amx:facet>
</dvtm:comboChart>kr
PeterHi Jan,
meanwhile I have managed to display the second Y axix corret.
Here my code:
<dvtm:comboChart var="row"
value="#{bindings.lmrgGraph.collectionModel}"
id="cc1" animationOnDisplay="alphaFade"
hideAndShowBehavior="withRescale"
rolloverBehavior="dim" inlineStyle="height:50%;">
<amx:facet name="dataStamp">
<dvtm:chartDataItem group="#{row.timeStamp}"
value="#{row.acetat}"
series="#{bindings.lmrgGraph.hints.acetat.label}"/>
<dvtm:chartDataItem group="#{row.timeStamp}"
value="#{row.plannedMachines}"
series="#{bindings.lmrgGraph.hints.plannedMachines.label}"/>
<dvtm:chartDataItem group="#{row.timeStamp}"
value="#{row.actualMachines}"
series="#{bindings.lmrgGraph.hints.actualMachines.label}"/>
</amx:facet>
<amx:facet name="seriesStamp">
<dvtm:seriesStyle series="#{bindings.lmrgGraph.hints.acetat.label}"
color="0052ff" type="line"/>
<dvtm:seriesStyle assignedToY2="true" color="e7e700"
type="line"
series="#{bindings.lmrgGraph.hints.plannedMachines.label}"/>
<dvtm:seriesStyle assignedToY2="true" color="94f700"
type="line"
series="#{bindings.lmrgGraph.hints.actualMachines.label}"/>
</amx:facet>
<dvtm:xAxis/>
</dvtm:comboChart>
/code]
There are still some issues if x-axis is timestamp enables but I have already created an SR for this.
regards
Peter -
How To Replace LOVs With Buttons
Hi all,
can someone please advise if it is possible to replace LOVs with Buttons? Customer has a requirement to replace the LOVs with buttons in Compensation Manager to approve/reject the paysheet. This is for R12.1.3.
Many thanks
AmandaHi,
1) First create a new region of LOV type.
2) Then under flowlayout region, add lov action button. On its 'External LOV' property, give the path of lov region created in step1.
3) Right click on 'lov action button' to add 'lovActionMappings'.
--Sushant -
How to replace #MISSING with 0 in Hyperion Financial Report
I am developing report in Hyperion Financial Reporting Studio. The report shows #MISSING for no data and does not look nice. I want to replace #MISSING with 0 (Like I did in SmartVIEW). However, I could not find a way to do that in Financial Reporting Studio.
Thank you for any help in advance.To replace no data (#MISSING) in cells, type a value in the No Data text box.
Refer: Page 191 of http://download.oracle.com/docs/cd/E12825_01/epm.111/fr_user.pdf
HTH-
Jasmine. -
How to replace my burnt ipad while charging it ?????
plz. HELP ????
its warranty is till august 18, 2014.This is a user-to-user forum here. You need to talk to Apple Support directly.
http://www.apple.com/support/contact/ -
How to replace IMessage with Ichat
I have recently updates to os x mountain Lion, and Ichat has been replaced. I hate IMessage how do i get back Ichat.
HI,
The iChat App is specific to each Update within an OS X version run.
Messages is the version on Mountain Lion.
At OS X 10.8.2 it became version 7.0.1
That is to say that version 7.0 lasted for OS X 10.8 and 10.8.1
You can get Messages to look somewhat iChat like.
Lets say you have AIM (or AIM valid) Names and some Jabber IDs (including GoogleTalk or Facebook)
Either Add them in Messages the same way you would have in iChat (Use the Plus icon in Preferences > Accounts) or by activating the choice for Messages in System Preferences > Mail, Contacts and Calendars for any ID/Name you use in Mail or elsewhere.
This will give you a list of Accounts in the Messages Menu > Preferences > Accounts including the iMessages one and the Bonjour one.
If all are Enabled then the Window menu will now show Buddies (CMD + 1) in addition to the Messages (CMD +0)
If you use this you will see a combined Buddy List.
The can be unlinked by going to Messages > Preferences > General Section and Unticking the line that talks about "gather all accounts in to one list" (actually it is only Buddy lists Account and does not include the iMessages account)
The Window Menu will now list as many Buddy lists as you have Accounts (Less the iMessage one and any that are not logged in.)
Each will have it's own keystrokes listed.
The title of the Buddy list and the Name in the Window Menu is dependant on the Description Field in the accounts pane.
Example Pic of the Accounts Prefs pane with Buddy lists
The iMessages account does not have to be active.
The main draw back is the Messages window itself with it's dual purpose Tabbed Chat window and interface to start Chats without using the Buddy lists.
Double clicking a chat will open it in it's own window.
9:39 PM Thursday; January 24, 2013
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.2)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images." No, Seriously -
How to replace "." with "," and "," with "." in a quantity field
HI All,
I wanna display the field mard-labst in the alv report. Based on the user default settings 2,454.500 is displayed as 2.454,500. Without changing the user default settings how can i display the decimal position correctly..Any help would be highly appreciated.
Best regards,
Subhakar RamineniHi...Subhakar..
i got ur prob...this is the solution...just paste it and go through it...
Report YH642_TEST.
TABLES:
mard.
DATA : W_mard_labst type p decimals 3,
w_dt1(18).
data:
W_N TYPE I.
SELECT SINGLE * FROM MARD INTO MARD WHERE LABST = '10000.00'.
WRITE: mard-labst .
W_mard_labst = mard-labst.
WRITE:/ W_mard_labst .
w_dt1 = w_mard_labst .
write W_mard_labst to w_dt1.
W_N = STRLEN( W_DT1 ).
W_N = W_N - 4.
REPLACE ALL OCCURRENCES OF ',' IN W_DT1 WITH '.' .
REPLACE ALL OCCURRENCES OF '.'
IN SECTION OFFSET W_N LENGTH 4 OF W_DT1 WITH ','.
WRITE: / W_DT1. -
How to replace name with number ID
Example:
Table1
T1ID Name1
1 John Smith
2 Kathy Smith
Table2
T2ID Name2
100 John Smith
101 Kathy Smith
102 John Smith
103 Kathy Smith
I want to replace all names in column called Name2 in Table 2, with matching T1ID from Table 1. There are many name repetitions in Table 2.If Name2 is VARCHAR and T1id is number then it would be better to add a new column with a consistent data type;
Sample data;
create table table1 as (
select 1 t1id, 'John Smith' name1 from dual union all
select 2, 'Kathy Smith'from dual);
Table created
alter table table1 add constraint table1_pk primary key (t1id);
Table altered
create table table2 as (
select 100 t2id, 'John Smith' name2 from dual union all
select 101, 'Kathy Smith' from dual union all
select 102, 'John Smith' from dual union all
select 103, 'Kathy Smith' from dual);
Table createdAdd the new column;
alter table table2
add name_id references table1(t1id);
Table alteredUpdate the new column;
merge into table2 t2
using (select t1id, name1
from table1) t1
on (t2.name2 = t1.name1)
when matched then
update
set t2.name_id = t1.t1id;
DoneDrop the retired column;
alter table table2 drop column name2;
Table altered
select * from table2;
T2ID NAME_ID
100 1
101 2
102 1
103 2 -
How to replace lvlib with lvlibp programmatically
Hello,
in the project explorer there is the possibility to do a "Replace with a packed library" from the context menu.
How can I do this programmatically?
Thank you.
ChristianI have a specific use case for this, and was wondering if anyone figured out how to do it. My Google search does not turn up much other than this thread.
My use case: I have main code branch that is not ready for LVLIPB's because the architecture is not 100% complete. However, we are release an Executable build on that relies on a pluggable actor framework architecture. Currently I manually branch the code, replace all LVLIB's with LVLIBP's then build additional LVLIPB's from that code and go back and replace the LVLIB's. At that point my code is now ready to be build as an executable with plug-ins. This process takes about 1-2 hrs to complete. This process works and works well repeatedly, it is just time consuming due to the relining. If I could just off load it to another PC that would enable to me to make additional bug fixes or work other issues in the main code branch. Currently we build about once a day or two for final release testing.
Any help in to script this would be much appreciated.
Thanks!
Brian G. Shea
Systems Integrator / Certified LabVIEW Architect
National Technical System, Inc. -
How to replace Consolekit with systemd-loginctl
Is systemd's new multiseat ready to replace consolekit?
And if, how can I achieve that?
My Background:
- I use systemd as my init system
- login into a getty
- which create a new X session with startx through a login script
I have had a hard time before I had the right setup to supervise everything with *ck-launch-session* and *dbus-launch* (order matters).
And sometimes without a reason, something breaks and I'm not allowed to mount USB drives or shutdown as a user without a reboot.
Last edited by Mic92 (2012-06-01 13:36:59)I do have a session:
┌─[jente @ lappy ~] 21:48:14
└─■ loginctl
SESSION UID USER SEAT
1 1000 jente seat0
1 sessions listed.
I start Udiskie through .xinitrc, like so:
if test -z "$DBUS_SESSION_BUS_ADDRESS" ; then
eval `dbus-launch --sh-syntax --exit-with-session`
fi
exec bash -c "udiskie & $HOME/.bin/dwm_start"
With .bin/dwm_start:
#!/bin/bash
while true; do
dwm >/dev/null 2>&1
done
EDIT: Here's udiskie's output when I plug in my external HD:
attempting to mount device /org/freedesktop/UDisks/devices/sdb2 (ext4:[])
failed to mount device /org/freedesktop/UDisks/devices/sdb2: org.freedesktop.UDisks.Error.PermissionDenied: Not Authorized
attempting to mount device /org/freedesktop/UDisks/devices/sdb1 (ntfs:[])
failed to mount device /org/freedesktop/UDisks/devices/sdb1: org.freedesktop.UDisks.Error.PermissionDenied: Not Authorized
EDIT2:
Changing my .xinitrc to the following didn't help either:
udiskie &
exec $HOME/.bin/dwm_start
Also, I found out I have to enter my root password to shutdown/reboot, whereas I didn't have to before.
Last edited by Unia (2012-09-05 19:55:23) -
How to Replace Footage with an AVCHD .MTS?
I have a sequence edited together from what I thought was a master H264 M4V. I now find out that the real master is AVCHD. So how can I replace my M4V footage with an MTS?
If I do a Replace Footage, I can see multiple AVCHD MTS Streams and the usual mess of folders inside a BDMV folder, but I seem to only be able to import via Media Browser. Replace Footage doesn't work with files already in Premiere, right?
I've only worked with AVCHD files once before, so I'm a little lost.Jim, I'm sure we've had this discussion before..... but it's not the fault of either the camera makers OR Mac users Since I'm now using both Mac and Windows 7 equally, I really have no axe to grind against either company.
This is entriely the fault of Microsoft who were unwilling to license NTFS to other companies, including Apple, Linux etc, added to the fact that NTFS is not suitable for lower powered devices with small amounts of embedded RAM. NTFS is simply too complicated for them to handle using small microcontrollers, so hoping for NTFS on cameras is folly in my mind. It's just not going to happen.
Apple, like Linux also have a file system that can handle larger files, larger even than NTFS. The Linux file system is also open source and royalty free, so could be used free of charge by lots of camera manufacurors if they wanted to (excpet it's also a lot more complicated than FAT32), but Microsoft choose not to support it (i.e. you couldn't read the cards on Windows), probably to try block Linux getting an even stronger hold on their server market than it has already.
The fact is that FAT32 was simple to implement for small memory devices of years gone by and nothing has come along to replace it that was (a) easy on the CPU / RAM and (b) royalty free.
There's no reason they couldn't implement a FAT64, FAT128 etc, though Microsoft would probably be the sticking point there too.....
UDF was supposed to be a new replacement that could be universal (hence the name Universal Disk Format), and indeed it's easy to use in read only format (UDF 1.2 is used by even the lowest powered DVD player from 15 years ago!) but to write to UDF takes a lot more power and memory. Also, the UDF format has evolved and is now even more complicated than before. So, UDF is not an option either.
So, yes, the 2GB limited is caused by a 2s compliment implementation of a 32 bit file system (tecnically it could do almost 4GB, allowing for FAT terminators etc, but they only use 31 bits for the file size, which allows for reverse seeking), in a FAT (File Allocation Table) format.
Finding the next lowest common denominator is the task I hope they pull off soon. While we can all usually work around the 2GB limit (by joining files) it would be much easier to have complete files in the first place
Maybe you are looking for
-
Will Let's Edit run on Windows XP mode in Windows 7?
I just purchsed an iMac and I want to load Windows 7 Professional onto it as well. We own the full version of Edius 5 but have not tried learning that program yet. I don't know if Edius 5 will run on Windows 7 but if I can still use Let's Edit I'll b
-
I have Adobe Acrobat 9 standard installed. I am trying to rotate 1 page out of a 50 page pdf document. Documents -> Rotate Page feature is grayed out. And so is Pages -> Rotate Page. Is this feature not available in AA 9 standard? Is there another wa
-
N97 mini battery level drops suddenly
I've observed my N97 mini's battery level dropping abruptly from 4 bars to 1 bar (with low battery alarm). The phone's slightly more than a month old and using the latest 11.x.x firmware. Did a bit of googling, and found several suggestions on how to
-
I am thinking of replacing one of my powerbooks with a Macbook for us on my sailboat. So I need a DC/DC converter and one does not seem to be available for the Macbook. I do know that I can possibly use a DC to AC converter but aside from not wanting
-
What is the Best was to create a newsletter application using BEA / Documen
Hi, I have some queries. What is the Best was to create a newsletter application using BEA / Documentum The newsletter will be republished and users will see new content every month. We plan to use BEA portal 8.1 sp3 with Documentum 5.3Sp1 / SCS. The