How to request and install 3rd Party certificate on CAS servers 2010

I have 6 CAS/HUB server installed in same AD site but located physcially at different locations. I need to renew the certificate on all of this servers. We are using Godaddy certificate. Could you please provide the steps to create CSR for all the CAS/HUB
server and how to assign services and import on all the CAS/HUB servers.
Service: IIS/Activesync/OWA/Autodiscover/SMTP/Outlook anywhere.
Note: CAS/HUB is installed on the same server.

Hi,
Generally, to renew a certificate in Exchange server 2010, we can do these steps:
1. Use the New-ExchangeCertificate cmdlet to generate a new certificate request:
New-Exchangecertificate -domainname mail.domain.com, autodiscover.domain.com
-generaterequest:$true -keysize 1024 -path "c:\Certificates\xxxx.req” -privatekeyexportable:$true –subjectname "c=US o=domain.com, CN=server.domain.com"
2. Submit the certificate request to your chosen Certificate Authority(Godaddy), then the CA issues a certificate or chain of certificates.
3. Install the issued SSL certificate on the Exchange 2010 server.
Import-ExchangeCertificate -FileData ([Byte[]]$(Get-Content -Path “c:\Certificates\xxxx.pfx” -Encoding byte -ReadCount 0))
4. Assign the new SSL certificate to the appropriate services on the Exchange 2010 server.
Enable-ExchangeCertificate -Server 'EXCH-H-868' -Services 'IMAP, POP, IIS, SMTP' -Thumbprint 'EDF57B5F9D81F1EC329BFB77ADD4465B426A40FB'
5. Restart IIS service.
Best Regards,
Winnie Liang
TechNet Community Support

Similar Messages

How to request and install a microsoft certificate through CA to Apple TV

how to request and install a microsoft certificate through CA to Apple TV

Apple TV does not have a browser and you can't install certificates on it
if you are using mirror from a mac or a ios device its on them you needs to take actions
when using mirror the Apple TV is just a remote display

After power down and a cold restart, I automatically restart in my Administrator Account. Running 10.8.4 with one Administrator account, one user account and one guest account. Recently downloaded and installed 3rd party software (Panorama).

After power down and a cold restart, I automatically restart in my Administrator Account. Running 10.8.4 with one Administrator account, one user account and one guest account. Recently downloaded and installed 3rd party software (Panorama). Installation required that I create a super user named Other with root privileges. I did so and successfully installed the 3rd party software. I powered down a few days late and when I restarted, I went automatically to my Administrator account with no login password required. I deleted the Other account, powered down and restarted with the same result - opened in Administrator. I then followed the steps to disable root user, powered down, cold restart - same result, opened in Administrator account.
Any suggestions? Any thoughts? Much appreciate any help you might offer.
jtsinphl

Welcome to Apple Support Communities
Disable automatic login. Open System Preferences > Users and Groups > Login Options, press the padlock at the bottom left corner, and select "Off" next to "Automatic login"

Installing 3rd party certificate in Cisco ASA

Hi,
We have configured an CSR in Cisco ASA for 3rd party CA to generate the certificate, however, the CSR configuration was lost because of some reason.
How can we install this certificate without the CSR in Cisco ASA. Or we have to generate another certificate from CA, it will be chargebale for the new certificate.
Anyone can help to advise ?
Thanks
Veon

You don't need the CSR once you have received the certificate from the third party certificate vendor. Just upload the CA Root certificate and the identity certificate from the certificate vendor to the ASA.
Here is configuration guide for your reference:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00808b3cff.shtml
Hope that helps.

Error installing 3rd party certificate on wism

Hi ..
Due to expire of cert.. We got re-get a new wildcard cert..
I have make pem from 3rd. CA (issuer=/C=BE/O=GlobalSign)
follow http://www.my80211.com/home/2011/1/16/wlcgenerate-third-party-web-authentication-certificate-for-a.html
using openssl (0.9.8zc) install on wism (7.0.220.0)
it's always show fail .
Old.pem is the same CA ，follow http://www.my80211.com/home/2011/1/16/wlcgenerate-third-party-web-authentication-certificate-for-a.html
it's okay to make pem and install on it , but just expired..
two cert from CA, there is different .
old is sha1WithRSAEncryption
new is sha256WithRSAEncryption
any one has idea to using new pem to install on WLC
Thanks

HI
After upgrade newest 7.0.251.
install the pem ...OKAY ..reboot test okay
due to using Mobility Services Engine I need go back to 7.0.220.0
It's show as attach ..no Certificate desc ...
Try Using IE /Firefox show cert is okay!!

Bea Portal: Installing 3rd Party Portlets / cms portlets

Hi there,
I hope this question is not too silly, but I am new to Bea Portal
Server. How do I properly install 3rd party portlets, e.g. the
cmsportlets available for download on the developer page ?
I extracted the zip files and then there is an Ant-Script where one's
supposed to change some parameters according to ones installation. I did
this and then I ran Ant, which actually copied the files to the portlets
directory. This is already strange to me: can the EBCC just create new
portlets or can it do something like "import" resources that someone
else has developed?
Well, so even after running ant, the portlets can be seen in EBCC, but I
an not add them to my page.
Any idea how to move on ?
Thanks
Hinrich

Hi,
Did you have a chance to look into WebLogic Portal 8.1 SP3? Check out the new Library Services features, which includes versioning and simple approval:
http://e-docs.bea.com/wlp/docs81/adminportal/help/CM_MAN_LifecycleOV.html
We also provide a few ootb portlets that allow users to interact with the CM system. Let us know if you have additional questions.
Best Regards,
--alex

WLC5760 - CSR request for 3rd party certificate

I need to generate a CSR request to obtain a 3rd party certificate for my WLC.
i am not sure how i can do that. all document availble are for wlc 4400.
let me know if the same process will apply to wlc5760 as well.

Thanks Matteo,
I managed to get it done, Yes I used OpenSSL to generate CSR.
Here what I have learnt about it, including WebAuth Cert installation on 5760. This may be useful to someone else.
http://mrncciew.com/2014/07/30/5760-webauth-certificates/
HTH
Rasika
**** Pls rate all useful responses ****

How to install 3rd party counters?

Is it possible to install 3rd party counters such as NeoWorks counters
in iWeb 06? I saw it mentioned in this forum but I am thinking it only
works in iWeb 08, or am I wrong, and if so, how can the html code be inserted?
I see an "insert" menu option Insert/choose....is this it? and what would I choose?
thank you,
todd

Ok I just downloaded BBedit. Now before I dive into the big manual can
you give me the quick take on where to past widget code? Do I insert and
the front before the original index code or at the end? If at the end, is it
just before the </head.<body><body></html>
or after that
I tried inserting at the very front and it appeared momentarily on the published document but was then quickly covered over by the original page.
todd

How to get rid of 3rd party and others similar annoying adds????

How to get rid of 3rd party and others similar annoying adds????

If you have somehow acquired adware or malware, or maybe some add-ons to your browser
that can be seen in that part of your preference controls for the browser, you may be able to
follow instructions on adware removal to be sure that isn't the problem. You can also go into
the browser and be sure the add-ons don't load.
Some items such as Spigot, genieo, and others can be included in free download or other sites
where the content is spiced with badware; sometimes a click-to-download gets you some other
content instead of what you thought it was. There even are browser redirecting items that keep
you looking at some page you don't want; and if you click on stuff, you may get more badware.
•Adware Removal Guide:
http://www.thesafemac.com/arg/
•Adware Medic: (removal method)
http://www.adwaremedic.com/index.php
•Mac Malware Guide:
http://www.thesafemac.com/mmg/
Some may suggest also using a tool by the name Etrecheck, but this by itself does nothing if
you don't know what to do next, however it does give you a partial list of some potential items
that could be indicative of troublesome software or adware, stuff to also remove.
•About EtreCheck
http://www.etresoft.com/etrecheck_story
Hopefully this may be of help, and should be useful to understand &/or indentify issues.
Good luck & happy computing!

Exchange Server 2010 Edge Transport Subscription Issue while moving Internal CA Certificate to 3rd Party Certificate

My Client have a Exchange 2010 Organization with Single Domain Single Forest.
They were using Internal CA Certificate and a TLS Cert.
As a POC we are doing a POC for Exchange 2010 Hybrid Office 365 Environment.
For this 3rd Party CA is Mandatory and they have bought a Geo Trust Certificate.
Now when they have installed cert on both HUB as well as EDGE servers, he was prompted to do edge subscription again.
HUB and CAS are combined on the server at both Main and DR Site.
When they try to do edge subscription again they are getting the following error.
SYED WASIL UDDIN Infrastructure Consultant/System Engineer Premier Systems (Pvt.) Ltd.

I was finding out the solution and got this.
1-Certificate will import on both EDGE and HUB Servers.
2-Edge Sync will use Self-Sign Certificate (but I an unable to find how do I configure this)
3-some communication between Edge and Hub will be encrypted via 3rd party Certificate.
Could anyone suggest, which services on HUB must based in this 3rd party cert.
All the external communication must be encrypted via 3rd party CA and communication between HUB-EDGE will set on self-sign Cert. How do I do this.
SYED WASIL UDDIN Infrastructure Consultant/System Engineer Premier Systems (Pvt.) Ltd.
Hi,
Please run Get-ExchangeCertificate | fl to check your Exchange certificate settings. Also confirm if the 5E470560626E313646730C177FCA66728E2BAFF7 certificate is your trusted 3rd party cert.
Please use Enable-ExchangeCertificate cmdlet to assign SMTP service to your self-signed certificate in your Edge server.
Regards,
Winnie Liang
TechNet Community Support

WLC526 install third party certificate

Hi! I would like to install a 3rd party certificate to get rid of the certificate warning for my web authenticated users. Can´t find any documentation about this. Has anyone done this on a 526 express controller? Is it possible?
Martin

Hi,
How do you export the certificate from ServerA and import it to ServerB? Does the certificate in ServerA work well?
Please refer to the following article to make sure your certificate exporting and importing for multiple server using is doing correctly:
http://exchangeserverpro.com/exchange-2013-ssl-certificate-export-import/
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information
found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
If the exporting and importing steps are correct and the issue persists, please run the following command to check your certificates settings:
Get-ExchangeCertificate | FL
Thanks,
Winnie Liang
TechNet Community Support

Farm member not using 3rd party certificate

I have a Microsoft server 2008 R2 RDS farm using a broker and NLB farm nodes.
In the farm member node ( not the broker ), I open “Remote Desktop Session Host Configuration” tool I selected “member of farm RD Connection Broker” and in the “general” tab under the “certificate” section I clicked “select” and picked the 3rd party
Certificate.
This is a Farm member. When I use a rdp client to go to farmName.domain.com I get a pop up with a certificate error and it shows the certificate as serverName.domain.com and not the name in the “farm” certificate.
How can I troubleshoot this issue.

Hi,
Iniitally seems the certificate is not from valid trusted authority. So please check the trusted authority. Apart there is mismatch in certificate name with server name.
The name in the Subject line of the server certificate (certificate name, or CN) must match the FQDN, or the DNS name that the client uses to connect to the RD Gateway server, unless you are using wildcard certificates or the SAN attributes of certificates.
If your organization issues certificates from an enterprise certification authority (CA), a certificate template must be configured so that the appropriate name is supplied in the certificate request.
The certificate must be trusted on clients. That is, the public certificate of the CA that signed the RD Gateway server certificate must be located in the Trusted Root Certification Authorities store on the client computer.
In addition, please check beneath article for reference.
Configuring Remote Desktop certificates
http://blogs.msdn.com/b/rds/archive/2010/04/09/configuring-remote-desktop-certificates.aspx
Hope it helps!
Thanks.
Dharmesh Solanki
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

How can I use a 3rd party XML parser such as xerces with OC4J ?

Hi all tech experts,
I am using Oracle Application Server 10g Release 2 (10.1.2) and i have
installed Portal and Wireless and OracleAS Infrastructure on the same
computer.
i tried all the solutions on this thread
Use of Xerces Parser in out application with Oracle App Server 9.0.4
but still fighting.
I have also posted this query on OTN on following thread
How can I use a 3rd party XML parser such as xerces with OC4J?
but no reply....
Please help me on this issue.
Since OC4J is preconfigured to use the Oracle XML parser which is xmlparserv2.jar.
i have read the following article which states that
OC4J is preconfigured to use the Oracle XML parser. The Oracle XML parser is fully JAXP 1.1 compatible and will serve the needs of applications which require JAXP functionality. This approach does not require the download, installation, and configuration of additional XML parsers.
The Oracle XML parser (xmlparserv2.jar) is configured to load as a system level library of OC4J through it's inclusion as an entry in the Class-Path entry of the oc4j.jar Manifest.mf file. This results in the Oracle XML parser being used for all common deployment and packaging situations. You are not permitted to modify the Manifest.mf file of oc4j.jar.
It must be noted that configuring OC4J to run with any additional XML parser or JDBC library is not a supported configuration. We do know customers who have managed to successfully replace the system level XML parser and the Oracle JDBC drivers that ship with the product, but we do not support this type of configuration due to the possibility of unexpected system behavior and system errors that might occur from replacing the tested and certified libraries.
If you absolutely must use an additional XML parser such as xerces, then you have to start OC4J such that the xerces.jar file is loaded at a level above the OC4J system classpath. This can be accomplished using the -Xbootclasspath flag of the JRE.
i have also run the following command
java -Xbootclasspath/a:d:\xerces\xerces.jar -jar oc4j.jar
but no success.
How could i utilize my jar's like xerces.jar and xalan.jar for parsing instead of OC4J in-built parser ?
All reply will be highly appreciated.
Thnx in advance to all.
Neeraj Sidhaye
try_catch_finally @ Y !

Hi Neeraj Sidhaye,
I am trying to deploy a sample xform application to the Oracle Application Server (10.1.3). However, I encountered the class loader issue that is similar to your stuation. I tried all the three solutions but the application is still use the Oracle xml paser class. I am wondering if you have any insight about this?
Thanks for your help.
Xingsheng Qian
iPass Inc.
Here is the error message I got.
Message:
java.lang.ClassCastException: oracle.xml.parser.v2.XMLElement
Stack Trace:
org.chiba.xml.xforms.exception.XFormsException: java.lang.ClassCastException: oracle.xml.parser.v2.XMLElement
     at org.chiba.xml.xforms.Container.dispatch(Unknown Source)
     at org.chiba.xml.xforms.Container.dispatch(Unknown Source)
     at org.chiba.xml.xforms.Container.initModels(Unknown Source)
     at org.chiba.xml.xforms.Container.init(Unknown Source)
     at org.chiba.xml.xforms.ChibaBean.init(Unknown Source)
     at org.chiba.adapter.servlet.ServletAdapter.init(ServletAdapter.java:153)
     at org.chiba.adapter.servlet.ChibaServlet.doGet(ChibaServlet.java:303)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:743)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:856)
     at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:719)
     at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:376)
     at com.evermind.server.http.HttpRequestHandler.doProcessRequest(HttpRequestHandler.java:870)
     at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:451)
     at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:299)
     at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:187)
     at oracle.oc4j.network.ServerSocketReadHandler$SafeRunnable.run(ServerSocketReadHandler.java:260)
     at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:303)
     at java.lang.Thread.run(Thread.java:595)
Caused by: java.lang.ClassCastException: oracle.xml.parser.v2.XMLElement
     at org.chiba.xml.xforms.Instance.iterateModelItems(Unknown Source)
     at org.chiba.xml.xforms.Bind.initializeModelItems(Unknown Source)
     at org.chiba.xml.xforms.Bind.init(Unknown Source)
     at org.chiba.xml.xforms.Initializer.initializeBindElements(Unknown Source)
     at org.chiba.xml.xforms.Model.modelConstruct(Unknown Source)
     at org.chiba.xml.xforms.Model.performDefault(Unknown Source)
     at org.chiba.xml.xforms.XFormsDocument.performDefault(Unknown Source)
     at org.chiba.xml.xforms.XFormsDocument.dispatchEvent(Unknown Source)
     at org.apache.xerces.dom.NodeImpl.dispatchEvent(Unknown Source)
     ... 18 more

Install 3rd party PDF iFilter for index PDF file as attachment in e-mail (msg)

I have called Microsoft Permium Support, base on the reply, SharePoint 2013 does not support to index a PDF file attachment in E-mail (msg) except 3rd party iFilter installed. And they finally told me how to edit Windows Registry for install the Adobe iFilter.
But, the Adobe iFilter is too weak to call large PDF files. So, I would like to install and try the Foxit PDF iFilter, but I cannot find an installation guide for this 3rd party ifilter with SharePoint 2013.
Does anyone here have the experience for Foxit PDF iFilter with SharePoint 2013 can help me?
I am not sure it is bug or feature in SharePoint 2013, but in case I still have to install 3rd party iFilter for index PDF file. I have no idea what is the out of box pdf file indexing support for.

You ca plan to use Foxit.
steps are nearly the same which we use in sharepoint 2013
1. We need to update registry for pdf . Registry value is {987f8d1a-26e6-4554-b007-6b20e2680632}
2. we need to install the foxit ifilter
Here are steps for same
http://support.microsoft.com/kb/2293357
3. run below command:
net stop spsearch4
net start spsearch4
net stop osearch14
net start osearch14
Check below:
http://bjarnegram.wordpress.com/2011/07/13/installing-foxit-pdf-ifilter-on-sharepoint-server-2010/

Install third party certificate on MAC os X

Hello,
I have installed leport 10.5.X on my machine. I am new bie for MAc and want to install intermediate certificate for my domain from Digicert. I have registered from Digicsert. Please help me to how can I install on the machine. I also need to create a new certificate but when I tried to add it shows an error message like this.
"There are no valid root or intermediate certificate authorities available to sigh certificates. Use the "create certificate Authority" option to create a certificate authority."
Can anybody please help me to what should be the next step.
And how can I install third party certificate.
Thanks in advance.

There is a product called VolumeWorks that is supposed to do this. I looked at the demo, but I could not get it to see the extra space so I ended up backing it all up and erasing the Raid and doing a block copy with Carbon Copy Cloner.

How to request and install 3rd Party certificate on CAS servers 2010

Similar Messages

Maybe you are looking for