How to set the scan rate in the example "NI435x.vi" for the 435x DAQ device?

I am using LabVIEW 6i, A 4351 Temperature/Voltage DAQ, and am using the example vi "NI 435x thermocouple.vi"
How do I set the scan rate on this VI? I added a counter to just to see the time between acquisitions, and it is roughly 4s for only 4 channels. The Notch Filter is set at 60, but is there a control for scan rate on this example. I'd like to acquire around 1 Hz.

Using this DAQ example, it may be easiest to simply place a wait function in the loop and software time when the data is extracted from the board. You can also take a look a the NI-435x pallette and the examples it ships with, along with the timing specs on page 3-3 of the 435x manual and set the filters to meet your needs:
http://www.ni.com/pdf/manuals/321566c.pdf
Regards,
Chris

Similar Messages

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

Keithley 2701 LV driver: Setting the scan rate?

I downloaded the Keithley 2701 LV driver and the example programs work great. There is just one question that I have. I cannot find anywhere in the examples or in the LV drivers how to change the scan rate or scan interval. Everything else I'm able to change, such as number of points, channels, voltage levels, etc., but I can't figure out how to change my scan rate to once every 0.5 seconds or 1 second.
I'm not sure, maybe this is a question for Keithley but since it is a LV driver I decided to post here first.
I'm using LV8.2
Jeff

I am using the Keithley 2700 with the 7700 cards. There is a vi named "ke27xx Configure Aperture Timing.vi" in the "ke27xx.llb" .
The vi sets the integration time for the A/D converter. I was measuring 500uv and needed to improve my accuracy so increased my integration time.
Brian
LV 8.2
Brian

HOW DO I ACHIEVE A TIME STAMP, IN THE FIRST COLUMN OF MY SPREADSHEET IN EXCEL,SHOWING THE TIME INTERVAL, INCREASED BY THE SCAN RATE ?

FROM AI START VI TO FORMAT AND APPEND VI TO CONCATENATE STRINGS,SECOND INPUT IS TAB,THEN EVEY OTHER ONE IS TAB. THIRD AND FIFTH INPUT IS ATTACHED TO GET DATE/ TIME VI, THEN END OF LINE, THEN CHANNEL 0; TAB; CHANNEL 1;TAB, AND SO ON THROUGH CHANNEL 7. THEN THE LAST INPUT IS END OF LINE. ON THE SPREADSHEET I RECIEVE THE SCAN RATE, THEN THE DATE ,THEN THE TIME; ALL ON THE FIRST ROW. THE NEXT ROW HAS THE COLUMN LABLES, AND DATA GOES TO THE CORRECT COLUMN. BUT NO TIME STAMP COLUMN. I WOULD LIKE IT TO BE IN COLUMN "A" EVEN WITH THE FIRST ROW OF DATA. EX." 10:01:01 200 300 400
10:01:03 200 300 400
THANK YOU
FOR YOUR HELP, JOE BOB CRAIN

I think the best way is to generate an array of time values to send to your spreadsheet BEFORE channel 0 data.
To generate the array you can use Ramp Pattern.vi from 0 to 'Actual Scan Rate' (from AI Start) * number of scans performed.
That way in your spreadsheet you will have the first line same as now, next the columns with time(secs), channel 0, channel 1... channel 7.
If you need the time column with date and time string, you can use Get Date/Time in Seconds.vi when you begin acquisition, then sum the seconds obtained to the array calculated as above and next use Format Date/Time String.vi to obtain the time stamp you need, next build array of time stamps and sent to your spreadsheet.
Hope this helps
Roberto
Proud to use LW/CVI from 3.1 on.
My contributions to the Developer Zone Community
If I have helped you, why not giving me a kudos?

HT4623 I have an ipad3, iPhone3gs and iPhone5, my problem is my apple ID works all 3 devices but I need a second ID for the iPhone 5. How do I delete my ID and set up a new one for the iPhone5 but keeping my own apple ID for the iPad and iPhone 3GS

I have an ipad3, iPhone3gs and iPhone5, my problem is my apple ID works all 3 devices but I need a second ID for the iPhone 5. How do I delete my ID and set up a new one for the iPhone5 but keeping my own apple ID for the iPad and iPhone 3GS.

http://support.apple.com/kb/he37

How to set border lines in table and also in template in the smartforms ?

How to set border lines in table and also in template in the smartforms ?
As I have to create table with following detals
total row = 3
row1 = 3 column
row2 = 6 column
row3 = 9 column
for 2nd and 3rd row data to be fetched using coding.
so can anybody explain me what should i use
Table or Template ?
and I want the border like excel format.
Can anybody suggest me ?
Thanks
naresh

if the data is multiple i.e. line items choose table.
if the data is single i.e. fixed choose template.
Create table
> Draw u r no lines
> choose option select pattern
> select display framed patterns
Choose u r required one.
out lined, or full lined. u can choose option.
same procedure to be followed for template also.
with regards,
Kiran.G

The lens correction option in Lightroom 5 is for the Tamron 28-75mm lens, rather than the correct Tamron 18-270mm, even though it's correct in the Library metadata. How can I fix this?

The lens correction option in Lightroom 5 is for the Tamron 28-75mm lens, rather than the correct Tamron 18-270mm, even though it's correct in the Library metadata. How can I fix this?

Are you shooting RAW or JPG or some of both?
When you say it won't let you change it, does that mean there are no lens profiles at all, or no lens profiles that match your lens? If you set Auto or Default you can select any lens you want from the list of manufacturers and profiles and then the Setup says Custom. Of course this lens may not be the correct lens, but saying you cannot change it suggests there are no manufacturers or lenses listed on the dropdowns.
Most lens profiles are for RAW only, so if you shoot a mixture of RAW and JPG then for the JPGs the lens profile may not exist. If you are enabling Lens Profiles and have Auto or Default set and it chooses the wrong one then it may just be choosing the top one in the list for Canon if the specific profile doesn't exist for JPGs.
If you are shooting raw and the profile does exist then you should be able to correct the situation: In the list select the correct profile, then choose Setup: Save New Lens Profile Defaults, and select Default from the Setup instead of Auto and it should pick the correct lens every time. Assuming it does do that, then you can set Enable Lens Profiles = checked and Setup: Default and set those as your new Lightroom Defaults and it should pick the right lens.
If you are shooting JPG then the lens profile may well not exist and there's nothing you can do about that except not shoot JPG. If you feel like it you can hack a raw profile to be a jpg profile and put that hacked copy in the user-lens-profile area and LR will see it.

How can I switch the region code on MBP w/ DVD drive for the 5th and final time?

How can I switch the region code on MBP w/ DVD drive for the 5th and final time? It brings up the window with that world map to do it, including the warning that "this is the 5th and final time I can do this", when inserting a DVD and opening "DVD Player", but it never executes my click on the "Change Drive Region" button prompt.
VLC or Quicktime Player won't play it either, but won't bring up that window to change Region Code anyway....
Otherwise, I'm not having any other issues with this MBP at all. Peak performance on all counts :-)
I tried resetting SMC after chatting w/ Apple Support, but it didn't help.
That was the link they provided. Resetting the System Management Controller (SMC) on your Mac
Tried zapping PRAM as well.
Thanks for any clues, Rene

Region encoding is the mechanism that enables motion picture studios to control the worldwide release of their movies. It is required by the DVD Forum (http://www.dvdforum.org/forum.shtml) in all commercial hardware DVD players. Every DVD-Video disc contains one byte of data representing a region code, which limits where the disc can be played.
http://support.apple.com/kb/HT2397
Once you have set the region in DVD Player five times it cannot be changed. However see this also:
http://support.apple.com/kb/TA25416?viewlocale=en_US&locale=en_US
Instead, use VLC to view videos from different regions:
http://www.videolan.org/vlc/download-macosx.html

I ordered a battery for my laptop because it said to replace battery soon. How long can I let the new battery sit around as I wait for the old one to run out of more charge?

I ordered a battery for my laptop because it said to replace battery soon. How long can I let the new battery sit around as I wait for the old one to run out of more charge? Will the new one become less effective if it sits around too long?

How much capacity is remaining on your current battery?
Check your power status
From the  menu: Hold OPTION and click System Information... èHardware è Power
Copy and Paste in your reply.
The new battery will become less effective if you store it in a hot or humid environment. It should be stored at room temperature (22 C).
Long term storage (6 months):
Apple recommends that you store the battery with a 50% charge. If you store a battery when it’s fully discharged, it could fall into a deep discharge state, which renders it incapable of holding any charge. Conversely, if you store it fully charged for an extended period of time, the battery may experience some loss of battery capacity, meaning it will have a shorter life.
http://www.apple.com/batteries/

I am trying to play a DVD on my MacBook Pro and transmit it to my TV (use my TV as the monitor) utilizing a VGA cable and adapter for the Mac but the only image that shows up on the TV is the MacBook wall paper, any ideas on how I can transmit to my TV?

I am trying to play a DVD on my MacBook Pro and transmit it to my TV (using my TV as the monitor) utilizing a VGA cable and adapter for the Mac but the only image that shows up on the TV is the MacBook wall paper, any ideas on how I can transmit the movie from my MacBook to the TV? I also tried an HDMI cable and had the same issue.

you are probably seeing the extended display.. to see ur main display go to pefrences then display steeings and turn mirroring on.
this will display ur mbp main screen. good luck.

Can not update iTunes because I have iMac with 10.5.8 . How I will sync my iphone 6.0 with an older version of iTunes on my iMac???? There is no update for the software of my iMac and no update for the iTunes.... So how can I sync????

Can not update iTunes because I have iMac with 10.5.8 . How I will sync my iphone 6.0 with an older version of iTunes on my iMac???? There is no update for the software of my iMac and no update for the iTunes.... So how can I sync????

Requirements for iPhone 5:
Syncing with iTunes on a Mac or PC requires:
Mac: OS X v10.6.8 or later
PC: Windows 7; Windows Vista; or Windows XP Home or Professional with Service Pack 3 or later
iTunes 10.7 or later
The highest version of iTunes you can install is 10.6.3 which will not sync with the iPhone 5.
Roger Wilmut1 wrote:
It's always a good idea to check the requirements before purchasing.
The person I spoke with at 1-800-MY-APPLE gave me totally different info...she said the iPhone 5 would in fact sync with the older version of iTunes and that I could restore from my previous iPhone 4 backup and also bring in my music that way. Hmmm....
I'm inclined to go by the published specs, but now I have to jump thru a bunch of hoops I wasn't expecting to.

HT2509 Hello I wonder if anyone knows how to find, download and install a suitable IPA (phonetics) font for the Mac Air? I need to be able to use a pop up window of fonts.

Hello I wonder if anyone knows how to find, download and install a suitable IPA (phonetics) font for the MacBook Air? I need to be able to use a pop up window of fonts.

Unless you've done anything to change it, Google keeps every email that ever passes through their server in your All Mail folder/mailbox/label. Even if you delete stuff, they hold onto it, there. You have to go out of your way to actually delete anything permanently.

HT5622 I'm a student exchange from france in USA, I have an apple ID from france and a bank count in france but i want access to the apple store US because I'm here for the year and some app can be interesting for me (like my gym club app) how can i do ?

I'm a student exchange from france in USA, I have an apple ID from france and a bank count in france but i want access to the apple store US because I'm here for the year and some app can be interesting for me (like my gym club app) how can i do ?

you cant. you need a US bank account.

I ordered the IX500 Scan Snap through Amazon and received the incorrect XI Standard disc in Windows format instead of for my Mac. I contacted Amazon and they suggested I contact Scan Snap who suggests I contact Adobe for the correct disc. Please help.

I ordered the IX500 Scan Snap through Amazon and received the incorrect Adobe Acrobat XI Standard disc in Windows format instead of for my Mac. I contacted Amazon and they suggested I contact Scan Snap who suggests I contact Adobe for the correct disc. Please help.

Fujitsu delivers only Adobe Acrobat for Windows, not Mac.
http://www.fujitsu.com/global/services/computing/peripheral/scanners/product/ix500/

HT201250 which external hard drive should I choose/use as I am setting up Time Machine on my MacBook Pro 15 for the very first time?

Which external hard drive should I use/choose as I am setting up Time Machine on my MacBook Pro 15 for the very first time?

Any of these SATA HDDs that are at least the same size as your internal HDD (preferably larger capacity). In addition you will need an enclosure, preferably one with a Firewire as well as a USB connection.
http://eshop.macsales.com/shop/hard-drives/2.5-Notebook/
Ciao.

How to set the scan rate in the example "NI435x.vi" for the 435x DAQ device?

Similar Messages

Maybe you are looking for