How to set two radius servers one is window NPS another is cisco radius server

how to set two radius servers one is window NPS another is cisco radius server
when i try the following command, once window priority is first , i type cisco radius user name, it authenticated fail
i can not use both at the same time
radius-server host 192.168.1.3  is window NPS
radius-server host 192.168.1.1 is cisco radius
http://blog.skufel.net/2012/06/how-to-integrating-cisco-devices-access-with-microsoft-npsradius/
conf t
no aaa authentication login default line
no aaa authentication login local group radius
no aaa authorization exec default group radius if-authenticated
no aaa authorization network default group radius
no aaa accounting connection default start-stop group radius
aaa new-model
aaa group server radius IAS
 server 192.168.1.1 auth-port 1812 acct-port 1813
 server 192.168.1.3 auth-port 1812 acct-port 1813
aaa authentication login userAuthentication local group IAS
aaa authorization exec userAuthorization local group IAS if-authenticated
aaa authorization network userAuthorization local group IAS
aaa accounting exec default start-stop group IAS
aaa accounting system default start-stop group IAS
aaa session-id common
radius-server host 192.168.1.1 auth-port 1812 acct-port 1813
radius-server host 192.168.1.2 auth-port 1812 acct-port 1813
radius-server host 192.168.1.3 auth-port 1645 acct-port 1646
radius-server host 192.168.1.3 auth-port 1812 acct-port 1813
privilege exec level 1 show config
ip radius source-interface Gi0/1
line vty 0 4
 authorization exec userAuthorization
 login authentication userAuthentication
 transport input telnet
line vty 5 15
 authorization exec userAuthorization
 login authentication userAuthentication
 transport input telnet
end
conf t
aaa group server radius IAS
 server 192.168.1.3 auth-port 1812 acct-port 1813
 server 192.168.1.1 auth-port 1812 acct-port 1813
end

The first AAA server listed in your config will always be used unless/until it becomes unavailable. At that point the NAD would move down to the next AAA server defined on the list and use that one until it becomes unavailable and then move to third one, and so on. 
If you want to use two AAA servers at the same time then you will need to put a load balancer in front of them. Then the virtual IP (vip) will be listed in the NADs vs the individual AAA servers' IPs. 
I hope this helps!
Thank you for rating helpful posts!

Similar Messages

  • How to put two ipods on one computer

    how to put two ipods on one computer

    Set up the second exactly the same way as you set up the first. If iTunes is already installed, it doesn't need to be installed again.
    (64746)

  • How to set two attributes as  a primary key in database ?

    how to set two attributes as a primary key?
    Take COffeesbreak as an example ,
    let's suppose that there are cof_name ,sup_id,price and so on;
    the same cof_name may be suplied by more sup_ids,
    and one sup_id may suply more cof_names.
    so the Primary key should be set the cof_name and sup_id ,
    how to set ?
    (of course that i konw if I set a cof_id,the problem will be easy work out
    but now there are those like above)
    I set that as following:
    create table coffees (cof_name VARCHAR(32) PRIMARY KEY,sup_id INTEGER, PRIMARY KEY,PRICE INTEGER )
    THE database print error :cant add more primary keys!
    thanks in advance

    You can only use the PRIMARY KEY declaration on a column if it is the only Primary Key column.
    Use the PRIMARY KEY constraint statement instead.
    create table coffees (
      cof_name VARCHAR(32),
      sup_id INTEGER,  
      PRICE INTEGER,
      PRIMARY KEY ( cof_name ,sup_id )
    )Dave

  • How can update two rows in one query?

    How can update two rows in one query?
    Edited by: OracleM on May 4, 2009 12:16 AM

    What do you mean with "two rows"? May be two columns??
    If the where clause of UPDATE query matches two rows, then it will update two rows. If you want to update two columns, then add column names to your query
    UPDATE your_table SET col1=value1, col2=value2 WHERE your_where_clause- - - - - - - - - - - - - - - - - - - - -
    Kamran Agayev A. (10g OCP)
    http://kamranagayev.wordpress.com
    [Step by Step install Oracle on Linux and Automate the installation using Shell Script |http://kamranagayev.wordpress.com/2009/05/01/step-by-step-installing-oracle-database-10g-release-2-on-linux-centos-and-automate-the-installation-using-linux-shell-script/]

  • I have two iTunes accounts, one for music and another for audiobooks.  I want to merge them and maintain only one iTunes account.  How do I do it?

    I have two iTunes accounts, one for music and another for audiobooks.  I want to merge them and maintain only one iTunes account.  How do I do it?

    You cannot.

  • How to sync two IPhone with one PC , but with different applications

    How to sync two IPhone with one PC , but with different applications ?
    We have two IPhones , but one PC , we want to sync separately , is that possible ?

    Absolutely, connect each phone, select what content you want on each phone, then hit the sync button. iTunes will keep everything straight, by device, upon subsequent syncs, including separate backups.

  • How to set cookie value in one page and retrieve in another page using setA

    How to set cookie value in one page and retrieve in another page using setActionListener?
    I have tried with following code srcpage.jspx->destpage.jspx
    srcpage.jspx
    <af:table value="#{bindings.DepartmentsView1.collectionModel}"
    var="emp" rows="#{bindings.EMPView1.rangeSize}"
    first="#{bindings.EMPView1.rangeStart}"
    emptyText="#{bindings.DepartmentsView1.viewable ? 'No rows yet.' : 'Access Denied.'}">
    <af:column sortProperty="EmployeeName" sortable="false"
    headerText="Cookie Testing">
    <af:commandLink text="#{emp.EmployeeName}" action="success">
    <af:setActionListener from="#{emp.EmployeeName}"
    to="#{cookie}"/>
    </af:commandLink>
    </af:column>
    </af:table>
    espage.jspx
    <af:outputText value="Test Cookie Value: #{cookie}"/>
    ,Here Test Cookie Value prints the following instead of its original String value
    {JSESSIONID=javax.servlet.http.Cookie@7da288, oracle.uix=javax.servlet.http.Cookie@399f62}
    I have passed employee name "Robert" to cookie in srcpage.jspx,but it prints "JSESSIONID....." instead of "Robert" in destpage.jspx
    Thanks in advance
    Kalee

    Hi,
    "cookie" is a reserved name. If you want to write to a session scope attribute called "cookie" then you have to call #{sessionScope.cookie}. If you want to use EL to set and read from cookies then you will have to use
    #{cookie.cookieName}
    Note that #{cookie} writes to and returns a map
    check this: http://www.informit.com/articles/article.aspx?p=30946&seqNum=7
    Frank

  • In flex, How to set a value to one parameter, the parameter defined in a cffunction in a cfc file

    In flex, How to set a value to one parameter, the parameter
    defined in a cffunction in a cfc file, In the cffunction there are
    much cfargument, I want set a value to one of them, such as the
    cfc:
    <cffunction access="remote" name="myShow" output="false"
    returntype="struct">
    <cfargument name="ID" type="numeric" default=0>
    <cfargument name="GoodsID" type="string" default="">
    <cfargument name="DestTime" type="string" default="">
    <cfargument name="DestCount" type="numeric" default=1>
    How I set a value to only parameter one of them , such as set
    GoodsID when use mx:remoteObject.
    Thanks for your help

    Got maybe a solution for you, I have just tested it.
    So, the idea is to use intermediate variables. Imagine Var1 and Var2 variables that you refresh with your more or less complicated queries. Then what you can do is to refresh your final variable Var3 with a query using your intermediate variables. Here is an example for Oracle:
    select #Var1+#Var2 from dual
    This way you can make a chain of dependent variables: Var3 is using Var2 and Var2 is using Var1.
    Hope it helps.
    Shamil

  • Set two views in one portal page

    Hello all,
    I need to set two views in one portal page, or  tow deferent views have to be setted in one view, unfortunately i didn't find anythings in SAP forums about this subject
    please help me to reso

    Are you saying you have two separate WD Applications (both FPM) which you want to run as two iViews in the same Portal Page?  If so, this is a very basic NetWeaver Portal capability - to add more than one iView to a Page.  However this isn't the correct forum to discuss this, as that discussion would belong in the NetWeaver Portal Forum.
    http://help.sap.com/saphelp_nw70ehp2/helpdata/en/47/881b2a67731e1ee10000000a42189d/frameset.htm

  • How can I transfer apps from one iTunes library to another?

    How can I transfer apps from one iTunes library to another? My daughter has an iTouch, and I was managing it through my library. I have created an iTunes account for her, with a new iTouch, and would like to move the apps over. I tried to sync the old iTouch to the new library and it said it was already set up to sync with a different library. What is the best way to do this?

    You can transfer iTunes purchases by:
    iTunes Store: Transferring purchases from your iPhone, iPad, or iPod to a computer
    To make the new computer the syncing computer you have to:
    - Transfer iTunes purchases lIke I described above
    - Make a backup of the iPod on that computer by connecting the iPod and then right-clicking on the iPod under Devices in iTunes and selecting Back Up.
    - Restore the iPOd from that backup
    She will have to continue to use your iTunes ID to update the apps prchased with your account. To use her account she will have to log into the computer with her account (iTunes>Store) and change the sign in on the iPod by going to Settings>Store.

  • How can I create more than one main window in a page of SAP SCRIPT?

    How can I create more than one main window in a page of SAP SCRIPT? If anybody helps me I will be obliged.
    Regards,
    Subhasish

    Hi Ganguly,
    It is possible to have more than one main window in a same page.
    You create a main window and simply you copy and past it in the same page.. it will create first main window name as MAIN and other main windows as MAIN01,MAIN02.... up to MAIN99.
    Contets flow from MAIN , MAIN01, MAIN02.......................MAIN99. contents after filling the current window it flows to next window(by default, you skip as well with some keyword not sure could be NEW-WINDOW)
    you want print the main window data twice? or you want to create two main window in the same page ?
    1. give two copies in the no of copies in the output type screen ( Which pop up is coming after excute the program ).
    2. create two page with the same script form.
    3. you can write the coding inside the program to print twice the same page.
    Hope this information use full to you..

  • How do I move music from one apple ID to another

    How do I move music from one apple ID to another?

    If you want to change your iCloud ID to another existing ID you'll have to delete the account, create a new account with the other ID, and migrate your data (including the calendar) to the new account.  To do this, first go to Settings>iCloud on your iPad and turn all data you are syncing with iCloud (contacts, calendars, etc.) to Off.  When prompted choose to keep the data on your iPad.  After everything is turned off, scroll to the bottom and tap Delete Account.  (Note, this will delete the account from your iPad but not from iCloud.  The account will remain in iCloud if anyone else chooses to remain signed into it an continue to use it.)  Next, set up the new iCloud account using your new ID, then turn syncing for your data (contacts, etc.) back to On.*  When prompted, choose Merge.  This will upload the data to your new account.
    * If you only want to upload the calendar, only turn Calendar to On; but I'm assuming you will be the owner and want this to be your iCloud account on your iPad with all your data, and then your can share the calendar with others and administrate it.

  • How to set multiple ORACLE_HOME and ORACLE_SID, on Windows

    How to set multiple ORACLE_HOME and ORACLE_SID, on Windows.
    I have 5 oracle instances. Every time if i want to start up the services , I am manually setting the environment variable (ORACLE_HOME and ORACLE_SID) and starting the services one at a time.
    Can we set multiple ORACLE_HOME and ORACLE_SID in Start->My computer-> properties-> advance-> Environment variable.
    Thanks
    Naveen

    Hi ,
    Can you please give me the link, for the doc you are referring to
    Thanks
    Naveen

  • How do i transfer data from one internal tabe to another.

    Hi All,
             How do i transfer data from one internal tabe to another.
             Can i do it ebven if he tables are different in structure.
    Please Advice.
    Thanks in advance.

    Hi Saket Tiwari,
    I hope the earlier post by kashyap is good enough an answer. anywas in addition to it let me give a detailed
    explanation of how you can populate an internal table.
    1) Append data line by line.
         Syntax :  APPEND [<wa> TO / INITIAL LINE TO] <itab>.
    this appends new line to internal table <itab>.
    2) Using COLLECT statement.
                 COLLECT is another form of statement used for populating the internal tables.  Generally COLLECT is used while inserting lines into an internal table with unique standard key. The syntax for COLLECT statement is as shown
         Syntax : COLLECT [<wa> INTO] <itab>.
    3) Using INSERT statement
         Syntax  INSERT [<wa> INTO / INITIAL LINE INTO] <itab> [index <idx>].
    INSERT statement adds a line/work area to the internal table. You can specify the position at which the new line is to be added by using the INDEX clause with the INSERT statement.
    Now coming to your request..
    To append part or all of an internal table
         Syntax
                  APPEND LINES OF <itab1> [FROM <n1>] [TO <n2>] TO <itab2>.
    *     Note:
    Without the FROM and TO options, this statement appends the entire table <itab1> to <itab2>.*
    b) To insert part or all of an internal table into another internal table
         Syntax
              INSERT LINES OF <itab1> [FROM <n1>] [TO <n2>]
              INTO <itab2> [INDEX <idx>].
    c) Using Move statement.
    To copy entire contents of one table into another in one execution
         Syntax MOVE  <itab1> To <itab2>.
                   OR
              <itab1> = <itab2>.
    but u hav to be careful because he contents of itab2 will eb overwritten on the execution of this statement.
    These copy the contents of ITAB1 to ITAB2. Incase of internal tables with header line we have to use [] inorder to distinguish from work area. So, to copy contents of internal tables with header line  the syntax becomes,
    ITAB1[] = ITAB2[].
    Coming to the letter part of your question, Yes, we can copy values between tables having different structures.
    for this we use    
                                MOVE-CORRESPONDING <itab1> TO <itab2>
        this executes the statement for their header lines. Searches for the sub-fields which occur both in itab1 and itab2 and then generates, for all relevant field pairs which correspond to the
            sub-fields ni , statements of the form MOVE itab1-ni TO itab2-ni. The other fields remain unchanged.
    I hope the information provided has been of your help.
    Reward if useful.
    Regards,
    Jose

  • How do I transfer data from one exterior harddrive to another?

    How do I transfer data from one exterior harddrive to another when they are both connected to our Imac Desktop?

    Depends what you want to transfer...
    A few more Details about what you are trying to achieve would be good.

Maybe you are looking for