How to show a waveform signal in data dashboard and UI builder ???

Hey guys.
I have made a program that collect analog data from two vibration sensors and then i use the signalexpress power spectrum to get it in the frequency domain.
I would like to show the signals and the FFT in data dashboard and in UI builder and have some problems doing so.
I'm using Network shared variables and web services.
First question:
It seems that I'm loosing some data when I go through the Network shared double variable. I know that this is becouse i'm using a double variable and I would like to send a waveform but that is not possible becouse the charts in UI builder and data dashboard do not support waveform or?
Second question:
This is almost the same problem as the first question.
Its not possible to show the data directly from the signalexpress power spectrum becouse the XY graph in data dashboard only supports array of cluster of two numerics right ?
Is it possible to convert the data from the signalexpress power spectrum to array of cluster of two numerics ?
Or any other ideas would be appreciated

Hi Genex.
It is important to say, that the Network Shared Variables are not lossless. That might explain the behavior you are seeing. I would not expect the update rate of the UI Builder to be that high, which could lead to data loss.
For more information about choose the right network protocol, wether it is only for monitoring or streaming all available data, see the following article:
Using the Right Networking Protocol
Also, I have posted a reply to your other post about your second question.
Best Regards
Alex E. Petersen
Certified LabVIEW Developer (CLD)
Application Engineer
Image House PantoInspect

Similar Messages

How to convert a waveform signal into array of complex numbers

How to convert a waveform signal into array of complex numbers.

Hi Chaks,
try this:
(Get Waveform components, convert to complex DBL)
Message Edited by GerdW on 01-28-2008 09:23 AM
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome
Attachments:
ToCDB.png ‏1 KB

How to show the content of a data object in listbox

Hello together,
i have created a service employee_srv for my data object "Employee". How can I show the content of this data object in a listbox in my view, for example DropDownByKey.
Regards
Waldemar Schakiel

Hi,
An example to create a dynamic context in Webdynpro ABAP:
data:
rootnode_info TYPE REF TO if_wd_context_node_info,
dyn_node TYPE REF TO if_wd_context_node,
tabname_node TYPE REF TO if_wd_context_node,
tablename TYPE string.
rootnode_info = wd_context->get_node_info( ).
cl_wd_dynamic_tool=>create_nodeinfo_from_struct(
parent_info = rootnode_info
node_name = tablename " Data object Table name
structure_name = tablename
is_multiple = abap_true ).
***Bind data to Dynamic table:
DATA: stru_tab TYPE REF TO data.
FIELD-SYMBOLS:
<tab> TYPE table.
create internal table
CREATE DATA stru_tab TYPE TABLE OF (tablename).
ASSIGN stru_tab->* TO <tab>.
dyn_node = wd_context->get_child_node( name = tablename ).
Bind internal table to context node.
dyn_node->bind_table( <tab> ).
Shruthi

How to queue two waveforms in dynamic data

I am collecting two waveforms for voltage data via DAQ assistant. The output is dynamic data which I can view as two waveforms via a chart.
I am sending the retrived data to a queue for storage until a seperate loop can flush the queue and write the data to a measurement file via the Write to Measurement File vi.
When I retrive my measurement file only one of the two waveforms have been stored.
I have troubleshot the issue and have determined the correct data is going into the queue

I'd recommend posting some code. Are you passing in the two waveforms to the queue as an array of waveforms, or a cluster of waveforms? Without seeing the code, it is just a guess as to what is going on.

How to show email id in personal Data of ESS

Hi All,
I have a scenario in which i have to show the email id mail in personal data iview of the personal information .
Iam using NWDI . I have checked the personal data DC and found that the RFCs being called in the application are related to 0002 infotype. I didnt find any field for email id in 0002 infotype. In my case the email id has to be picked from su01 user data.
Please help me to proceed further.
Thanks,

Hi,
I think there ia already an Iview you can use. Check Change own data
http://help.sap.com/erp2005_ehp_04/helpdata/en/34/1100414a0e40a5ae68d5aeacc30165/frameset.htm
This picks email from from su01/su03
This is there in ESS version 1.0 also. You can add remove lot of fileds using the infoset in SPRO setting in
Personnel Management > Employee Self-Service > Service-Specific Settings > Whou2019s Who.
Srini

How can I install Itunes in the data drive and not in OS partition?

My PC has a 3 partitions and I hace installed Itunes in the OS partition, very small. How can I install Itunes in the data drive?

See Williams Lloyd's post > https://discussions.apple.com/message/15670671#15670671

How to create a new Structure of Data screen and screen sequence

Hi,
Can you give any link or explain all the steps required to create a new structure of data screen and how to assign it to our comapnay code or plant etc. also when i check the screen ref. which is assign to material type in OUR system i ROH but i have not found this ref. in OMT3B where i can see the screen ref. ROH as this the the standard.
regards,
zafar

Hi
Download the pdf's from the below link
http://www.pdf-search-engine.com/sap-mm-configuration-pdf.html
It will help
Thanks,
Raman

How to use the (gigabit) ethernet for data exchange and WLAN for Internet?

I have following setup:
- MB Pro SL 10.6
- Desktop PC Windows 7
- Wireless Printer
- Netgear WLAN Router
At the moment all my data and internet communication is done via the WLAN router on 192.168.1.x That works fine and I can exchange data, print and surf the internet. My problem is that big data exchanges > 10GB take ages via my 54Mbit WLAN Connection. Furthermore the WLAN router is far away from the PC so that it is not possible to plug in the Ethernet Cable of the PC and the MB to the router.
Now I've thought that there must be a possibility to use a 1 gigabit (cross) cable (like in the 90s ;)) to connect the MB and the PC directly. I know that I will need different IP ranges and so on, but I have no clue how to do that.
The final solution should be that the setup stays as it is (data exchange, print, internet via WLAN) and that additional it is possible to connect PC and MAC some times for big transfers via a Gigabit ethernet cable. because I only want to connect those two machines I don't think that a switch makes any sense, or?
Does someone know how to do that?
Thanks a lot in advance!
Message was edited by: whitepowder

Well if it were 2 Macs, I would configure each Mac with a fixed IP address (same subnet as my router, but outside of the routers DHCP assignment range).
I would give the same fixed IP address to both my Airport AND my ethernet interfaces. I would do the same to the other Mac using another fixed IP address.
My network service order would have the ethernet higher than the Airport on both systems.
Normally I would use WiFi, so ethernet would be idle and out of the loop.
When I wanted faster transfers, I would connect each Mac to the router via their own ethernet cables, and the Mac would automatically detect that the ethernet became available, and would switch to use the faster ethernet. Since Airport and ethernet have the same fixed IP address, I could even do this in the middle of a file transfer and no one would notice as packets were always going to/from the same IP addresses, just using a different route, which doesn't matter.
NOTE: I've been doing this on Macs since Mac OS X 10.3 days (or was it 10.2; to long ago to remember).
However, you have thrown a Windows system into the mix, and since I do not use Windows, I do not have a clue about what can be done on Windows. However, maybe this will give you some ideas, and asking the right questions in a Windows oriented forum may provide the Windows side of this setup.
Sorry, that is the best I can do. Maybe my reply will encourage someone else to offer their approach.

Issues with Using Data Dashboard and Using Web Service

After running a system for many months it has suddenly decided to not work at all. I am using Data Dashboard to read variables on a host. I'll outline the system here to get a baseline:
I'm running LV 2012 SP1 f5.
I collect data from one Ethernet port and interfact it to another Ethernet port to form a proxy.
I use a fixed IP address from my DSL along with port forwarding/port triggering in my router for data observation and control.
So, what have I done so far?
1. Repaired my original LV 2012 SP1 and tested system.
2. Upgraded to LV 2012 SP1 f5 and tested system.
3. Ran service.msc and checked all the NI services that should be operational. Started and stopped several of them and rebooted computer.
4. Deployed all my SVs (multiple times)
5. Disconnected second Ethernet interface becasue sometimes the variables would deploy to this IP address.
6. Turned off my wireless because sometimes the variables would deploy to this IP address.
7. Checked "Web Server Configuration" "Application Web Server" for correct port number.
8. Checked "Web Services Management" and under "Deployed Web Services" there is one category: SV is marked as running. NOTE!! WebService is NOT listed and this could be a problem
I can use the following to retrieve data&colon; localhost:<port number>/sv/variable. But when I substitute my DSL IP number, I can no longer get any data.
So, what am I missing?
Thanks,
Paul.

Siana,
Thanks for your response.
I haven't touched the NI code in months. It is running on an XP laptop and I have the Windows updates turned off. McAfee is running on it and of course that updates regularily. This laptop is a dedicated machine that I only use for this function, nothing else. I haven't added or subtracted any programs for many months.
There have been no changes to the DSL from me. AT&T is constantly trying to get us to upgrade to U-Verse but we have resisted. All DSL modem and router hardware is the same.
Confusing, huh?

How to show two waveforms on XY-graph?

Hello,
i have two array with x and Y-values that are bundled and then displayed in XY Graph.
How can i show two XY-waveforms on the graph at the same time?
Thanks
Solved!
Go to Solution.
Attachments:
Wave.jpg ‏48 KB

Hi one,
open the context help and move the mouse pointer of the XY graph. Then read the help!
Btw. you don't create waveforms, you create XY plots…
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

How to retrive dynamic directory structure from data base and show it

i want to display a directory structur on jsp my problem is that i want to read it from a database how i can read
a tree structure i found a function to read directry structur but if i use this function i am not able to find who the parent is ? this is the function i found cna any one help me ?
public void iterate(File someDirectory) {
Vector allFiles = new Vector();
File[] dirContents = someDirectory.listFiles();
for (File f : dirContents) {
allFiles.add(f);
for (int i = 0; i < allFiles.size(); i++) {
File file = (File) allFiles.get(i);
if (file.isDirectory()) {
dirContents = file.listFiles();
for (File f : dirContents) {
allFiles.add(f);
// Process 'file' or do whatever
}

Thanks for reply i am not actualy deling with files i am creating a web application in which i am having organize functionality
user creat folders and put there document in that like out look user can creat folder inside folder
i am storing tham in a database table my problem is how to retrive them so i can show them as a tree structur
i am using this code to show on jsp
{color:#808000}<table>
<tr>
<td >
<ul class="flipMenu">
<li><span class="menu">Folder</span>
<ul>
<c:forEach var="folderList1" items="${folderList}" >
{color}
{color:#808000}<li ><a class="submenu25" id='<c:out value="${folderList1.id}"/>' href="folderAgreement.htm?folderid=<c:out value="${folderList1.id}"/>" onmouseup="a('<c:out value="${folderList1.id}"/>');" ><span ><c:out value="${folderList1.name}" /> T</span></a>
<ul>
<li> <a href="# onclick="window.open('createSubFolder.htm?folderid=<c:out value="${folderList1.id"/>&agreetitle=<c:out value="${agreements.title}"/>', 'invite_wnd', 'height=700, width=800, status=no, menubar=no, toolbar=nu, location=400'); return false;">Add Folder
</li>
<li> <a href="folderDetail.htm?folderid=<c:out value=${folderList1.id"/>&flag=folder"><span class="submenu2">Detail</span>
</li>
<li> <a id="<c:out value="${folderList1.id}"/>" href="folderDelete.htm?folderid=<c:out value="${folderList1.id}"/>&flag=folder" onclick="conformDelete('<c:out value="${folderList1.id}"/>')" ><span class="submenu2">Delete Folder</span></a>
</li>
</ul>
</li>
</c:forEach>
{color}
{color:#808000}</ul>
</li>
</ul>
</td>
</tr>
</table>{color}

How to show time as well as date in Finder for file Date Modified

Completely mystified... Folder is only showing the mm/dd/yy modified for any file not modified Today (which then says Today and the time).
Why on Earth would the Date AND TIME not show for all files? I can't seem to find any option to do this. Definitely want a way to:
o make the change globally (not folder by folder)
o and extra credit if i can get four digit years showing too.
Complete mystery why this isn't the default view or maybe I did something inadvertantly to make things easier for people who don't want too much information. (?)

Try this:
Double click the Macintosh HD on the desktop > Cmd + J > Check the buttons you want concerning the date and time > press the button Use as default. Hopefully it will rub off on all the other folders too!

How do I open/view Signal Express Data .tdms files? (Absolutely Brand New User!)

Hi everyone,
I've inherited this data recording software from a previous engineer and tried it out for the first time the other week. Mind you I have no manuals or help really here, so bear with me that this is probably a very basic question.
I had a set-up using the Labview Signal Express ver.2.5 and NI-USB-6008 monitoring two voltages. I currently want to see the playback of the .tdms files which are located in my C:\Documents and Settings\TechSupport\My Documents\SignalExpress Data\08042009_015232_PM folder (3 files, voltage.tdms, voltage.tdms_index, and voltage_meta). I opened LabVIEW Signal Express and clicked "File", "Import", "Logged Signals From SignalExpress TDMS Files", and go to select the "voltage.tdms" file, but receive the error of "You cannot choose this folder name; a file of that name already exists".
Does anyone know what I'm doing wrong?
Thanks for any and all help (and let the sarcastic comments begin )

Sometimes, selecting current folder instead of open is a valid workaround.
Also, can you identify the program responsible for creating the log data? Are you able to view this data using another progarm like LabVIEW or DIAdem?
Regards,
Glenn
Regards,
Glenn

How to show NULL value when import data into excel

when retrieve data from sql server and import these data into excel.
data source is like : select a ,b c from tab
if a,b,c is nullable. when import these NULL value into excel, it becomes blank value, there is nothing in the excel cell.
if i don't want to use select isnull(a,'NULL') as a to convert the values.
what's else can i do to make it? is there a way to prevent changing the NULL to blank ?
or is there an easy solution to replace all the blank value to NULL in the excel ?

help me ~

How to sample an analog signal, simulated on labview and get the sample values.

My project involves this particular detail where i have to sample a simulated sine wave and get the samples and compare them so as to select a particular length for hanning window.Then it also requires me to experiment with the window size so as to get more efficient data out of the sampled signals. please help me with the sampling part and guide me as to how to perform a hanning window operation on the sampled signal. I have directly used the spectral analysis tool which involves getting a FFT spectrum by a default hanning window setting. But since i have to experiment with the window size and variations, guide me with the sampling part and applying a separate hanning window. Thank you.

bhardoo wrote:
My project involves this particular detail where i have to sample a simulated sine wave and get the samples and compare them so as to select a particular length for hanning window.Then it also requires me to experiment with the window size so as to get more efficient data out of the sampled signals. please help me with the sampling part and guide me as to how to perform a hanning window operation on the sampled signal. I have directly used the spectral analysis tool which involves getting a FFT spectrum by a default hanning window setting. But since i have to experiment with the window size and variations, guide me with the sampling part and applying a separate hanning window. Thank you.
What do you mean by i have to sample a simulated sine wave?
the sine generator will provide you with a waveform (or an array of values you can use), there are basic vis to do all this, rigth click on the vi and select help to get detailed information.
Post your vi if you have trouble with details.
How much do you know about LabVIEW and signal theorie?
Greetings from Germany
Henrik
LV since v3.1
“ground” is a convenient fantasy
'˙˙˙˙uıɐƃɐ lɐıp puɐ °06 ǝuoɥd ɹnoʎ uɹnʇ ǝsɐǝld 'ʎɹɐuıƃɐɯı sı pǝlɐıp ǝʌɐɥ noʎ ɹǝqɯnu ǝɥʇ'

How to show a waveform signal in data dashboard and UI builder ???

Similar Messages

Maybe you are looking for