How to test if TV-Out (VIVO) is defective?

Hi everybody!
How can I test if the VIVO connector (TV-Out) of my G4 ti4200-VIVO is defective?
I've read the thread "GF4 TV-OUT Guide" and I've tried everything explained there, but my TV keeps showing a blank screen.
There's no load detection (the drivers don't detect a TV connected). I've put my monitor in the DVI connection also, but nothing seems to work.
I've also tested to boot up my computer with ONLY the TV-out plugged. Nothing appears in the screen. I've tested the TV connection with another device and it works fine.
I'm starting to think that something in the card is broken....
Should the boot up process appear in the TV when only it is connected?
Many thanks in advance!!!
brutrak

Hi,
If you only have a TV connected, you should get the boot process appearing on the TV. It might not be readable, as it tends to default to NTSC on start-up, and older PAL TVs might not cope very well, but you should at least get something.
A rare (but not unknown) problem could be that the DC input impedance of the TV set is too high. TV sets (and other video gear - e.g. VCRs) should have a DC impedance (resistance) of about 75 ohms. The "TV-detect" circuitry on most TV-outs does a fairly crude resistance measurement, and if it "measures" a resistance below a threshold value (usually somewhere in the 100 to 200 ohm range), it thinks it has a TV connected. So, if you can get hold of a resistance meter (or multimeter), and can measure the resistance between the inner pin of the lead you plug into the TV (with the lead plugged into the TV but not the VIVO, but measured at the VIVO end), you should get a reading of around 75 ohms.
Naturally, you have to connect the TV to the Video OUT, not the IN to get a picture out
Cheers

Similar Messages

How do I get to the InDesign screen to begin testing this product out in the free trial?

How do I get to the InDesign screen to begin testing this product out in the free trial?

in ios 7 if you click the home button it takes you home. if you double click it it shows all the apps running in the multitasking bar. on ios 6 they looked like actual apps on ios 7 its the page of the app

How to test the update statement in SQLJ - Im lost and cant figure it out!

Hi Im wondering on the sytax of this logic.
//Execute an update on a table
#sql {update mytable set name = :test where today = sysdate };
//This is where im lost. how to test if the record is not found
if (record not found for update){
#sql {insert mytable set name = :test where today = sysdate };
I dont want to do a select count(*) and based on the value go to update or insert.
Does anyone know how to do it?
Thanks so much

If Software Update is offering the update then it would be compatible with your model. Unfortunately, you haven't provided us with any information on your hardware that would enable us to determine if it really is too old.
If you really wish to disable the update alert then the next time Software Update opens, select the update in the list then select "Ignore update" from SU's Update menu.

How to test a simple PL SQL function from another PL SQL script

Hi,
I have created a function. Now i need to test that whether it is returning the correct values or not.
For that, i have written anothe pl sql script and trying to call this function. Im passing all the IN parameters in that function. I assume here that OUT parameters will provide me the result. Im trying to display the OUT parameter one by one to see my result.
I'm using toad as sql client here connected with oracle.
pl sql script:-
DECLARE
BEGIN
     DBMS_OUTPUT.PUT_LINE('$$$$$$$ VINOD KUMAR NAIR $$$$$$$');
     FETCH_ORDER_PRODUCT_DATA(320171302, 1006, 6999,
ODNumber OUT VARCHAR2, Line_Number OUT VARCHAR2,
ServiceID OUT VARCHAR2, BilltoNumber OUT VARCHAR2,
AnnualPrice OUT NUMBER, CoverageCode OUT VARCHAR2)
DBMS_OUTPUT.PUT_LINE('HERE IS THE RESULT ' | ODNumber );
DBMS_OUTPUT.PUT_LINE('HERE IS THE RESULT ' | Line_Number );
DBMS_OUTPUT.PUT_LINE('HERE IS THE RESULT ' | ServiceID );
DBMS_OUTPUT.PUT_LINE('HERE IS THE RESULT ' | BilltoNumber );
DBMS_OUTPUT.PUT_LINE('HERE IS THE RESULT ' | AnnualPrice );
DBMS_OUTPUT.PUT_LINE('HERE IS THE RESULT ' | CoverageCode );
END;
Function:-
Program Name : SPOT_Order_Product_Data_For_CFS.sql
Description : Function to Validate parameters from CFS
By : Vinod Kumar
Date : 08/19/2011
Modification History
By When TAR Description
CREATE OR REPLACE FUNCTION FETCH_ORDER_PRODUCT_DATA(orderNumber IN VARCHAR2, customerNumber IN VARCHAR2,
productLine IN VARCHAR2, ODNumber OUT VARCHAR2,
Line_Number OUT VARCHAR2, ServiceID OUT VARCHAR2,
BilltoNumber OUT VARCHAR2, AnnualPrice OUT NUMBER,
CoverageCode OUT VARCHAR2)
RETURN VARCHAR2 IS
lv_err_msg VARCHAR2(100) := '';
lv_bucket_id VARCHAR2(14);
lv_bill_number VARCHAR2(30);
lv_anual_price NUMBER;
lv_coverage_code VARCHAR2(8);
lv_quote_num NUMBER(10) := NULL;
lv_line_num NUMBER(5) := 0;
lv_customer_number VARCHAR2(30) := customerNumber;
lv_product_id VARCHAR2(14) := productLine;
lv_count_quote NUMBER := 0;
lv_quote_status VARCHAR2(5);
lv_quote_version NUMBER(2):=0;
BEGIN
IF INSTR(orderNumber, '-') = 0 THEN
lv_quote_num := orderNumber;
ELSE
lv_quote_num := SPT_Delimiter(orderNumber, 1, '-');
lv_line_num := SPT_Delimiter(orderNumber, 2, '-');
END IF;
--Check status of the quote COM, APP
SELECT COUNT(*) INTO lv_count_quote FROM sot_order_header WHERE ORDER_NUMBER=lv_quote_num
AND ORDER_STATUS IN ('APP', 'COM') AND CUSTOMER_NUMBER = lv_customer_number;
IF lv_count_quote = 0 THEN
lv_err_msg := 'Invalid Order number';
RETURN lv_err_msg;
END IF;
-- Fetch the latest version on SPOT quote
SELECT MAX(VERSION_NUMBER) INTO lv_quote_version FROM SPT_QUOTE_HEADER WHERE QUOTE_NUMBER = lv_quote_num
AND CUSTOMER_NUMBER = lv_customer_number;
-- If quote is valid fetch the data in OUT parameters
IF lv_line_num = 0 THEN
BEGIN
SELECT a.CUSTOMER_BILLTO_NUMBER,
b.LINE_NUMBER, b.BUCKET_ID,
b.ANNUAL_REF_RATE_USD, b.COVERAGE_CODE
INTO lv_bill_number,lv_line_num,lv_bucket_id,lv_anual_price,lv_coverage_code
FROM SPT_QUOTE_HEADER a, SPT_QUOTE_LINE b
WHERE a.QUOTE_NUMBER = lv_quote_num
AND a.CUSTOMER_NUMBER = lv_customer_number
AND a.VERSION_NUMBER = lv_quote_version
AND a.QUOTE_NUMBER = b.QUOTE_NUMBER
AND a.VERSION_NUMBER = b.VERSION_NUMBER
AND b.PRODUCT_ID = lv_product_id;
ODNumber := lv_quote_num;
BilltoNumber := lv_bill_number;
Line_Number := lv_line_num;
ServiceID := lv_bucket_id;
AnnualPrice := lv_anual_price;
CoverageCode := lv_coverage_code;
RETURN '';
EXCEPTION WHEN OTHERS THEN
lv_err_msg := 'Multiple PIDs existing in the SPOT order, please provide the SPOT order + line number as input data';
RETURN lv_err_msg;
END;
ELSE
BEGIN
SELECT a.CUSTOMER_BILLTO_NUMBER,
b.BUCKET_ID, b.ANNUAL_REF_RATE_USD,
b.COVERAGE_CODE
INTO lv_bill_number,lv_bucket_id,lv_anual_price,lv_coverage_code
FROM SPT_QUOTE_HEADER a, SPT_QUOTE_LINE b
WHERE a.QUOTE_NUMBER = lv_quote_num
AND a.CUSTOMER_NUMBER = lv_customer_number
AND a.VERSION_NUMBER = lv_quote_version
AND a.QUOTE_NUMBER = b.QUOTE_NUMBER
AND a.VERSION_NUMBER = b.VERSION_NUMBER
AND b.PRODUCT_ID = lv_product_id
AND b.LINE_NUMBER = lv_line_num;
ODNumber := lv_quote_num;
BilltoNumber := lv_bill_number;
Line_Number := lv_line_num;
ServiceID := lv_bucket_id;
AnnualPrice := lv_anual_price;
CoverageCode := lv_coverage_code;
RETURN '';
EXCEPTION WHEN OTHERS THEN
          lv_err_msg := 'Multiple SPOT lines exist with same parameter';
          RETURN lv_err_msg;
END;
END IF;
EXCEPTION
WHEN OTHERS THEN
lv_err_msg := '@@@ EXCEPTION THROWN @@@ '|| SUBSTR(SQLERRM,1,120);
RETURN lv_err_msg ;
END;
Don't look at the function, it might have errors but my primary concern is how to test this function. Once I start doing its testing then only i can understand any bugs(if any).
My pl sql is not so good. Im still learning. I don't understand IN and OUT parameters are.
I just know that IN parameters r those whick we pass in to the function wen we call it and OUT parameters are those through which we get the result.
Thanks in advance
Vinod Kumar Nair

20100511 wrote:
I wondered how I could test the output of the function from within TOAD?I usually create the following function in my developer schema:
create or replace function BoolToChar( b boolean ) return varchar2 is
begin
if b then
    return( 'TRUE' );
else
    return( 'FALSE' );
end if;
end;To test a function like yours, the following will do in SQL*Plus/TOAD/etc:
begin
DBMS_OUTPUT.put_line(
    BoolToChar( XCCC_PO_APPROVALLIST_S1.does_cpa_exist(1017934) )
end;
I'm probably doing 101 things wrong here, but thought I'd ask anyway and risk being shouted at.Shout at? You reckon? I thought people risked being beaten with a lead pipe, or pelted with beer cans and stale pretzels - which makes being shouted at a really safe and viable alternative. {noformat};-){noformat}

How do I properly zero out or erase the hard drives in my early 2009 Mac Pro 4,1 tower?

How do I properly zero out or erase the hard drives in my early 2009 Mac Pro 4,1 tower?
I assume there are already instructions on Apple.com someplace but haven't seen them yet… I have to one terabyte drives one the operating system the other is blank I want to start fresh I want to zero out both drives but I didn't want to make any mistakes
I know I can use disk utility to 0 Out Dr., #2 that means I will have to take out the operating system hard drive out of my 2008 Mac Pro and put it into my 2009 Mac Pro to use the disk utility to zero out drive one the OS drive in my 2009 Mac Pro am my correct
I just need a little bit a help I want to go slow so I don't make any mistakes with the sleds or with the erasing process which journaled to choose encrypted or not etc. etc.
Furthermore is there instructions on the site on how to change the hard drive into a different sled because the sleds and my 2009 are different than my 2008 any advice
Thank you

I'm doing this because my friend told me that zeroing out the drive can nap bad sectors and also later for some kind of diagnostics usage of the drive or something like that he wasn't really clear
My friend was really specific he said choose the option that writes zero's once over the drive that is plenty good enough I was inclined to use the maximum seven write ...I just want to make sure the drive has no bad sectors and that's it's it's zeroed out for possible future diagnostics usage or something that he said was usable later
he also advised me to run a test on it but I don't have the software you mentioned or the software that he has… So I may have to take the drives over to his house unless you have some kind of free software that's easy to use that you could suggest that will not only zero out the drive but test the drive completely
I am completely new to Mac I'm no dummy but at the same time I'm not super technically capable I mean I can surprise myself I'm pretty good but I need a good teacher… How expensive is this lifeguard software?
Thank you

How to Test Mail's Trainable Filter?

In the Apple Support Discussions topic No Junk mailbox in Training mode? a question arose regarding how to test if the trainable filter (the filter that evaluates the "Message is Junk Mail" condition) is evaluated independently of the other conditional tests of the Junk Filter rule -- IOW, if some other test condition in the Junk Filter rule, like sender is not in the address book, evaluates to false, does the "Message is Junk Mail" test which follows it in the rule's list of conditions ever get evaluated?
A proposed test for this involved resending to yourself a message that Mail had previously marked as junk using the "Message > Send Again" function of Mail. It has been pointed out to me that this probably isn't a valid test because "Message > Send Again" doesn't send the original message in unaltered form (there are substantial changes in the header info regarding sender, path, etc.) & thus the filter may not consider the resent message as junk, even if it were to evaluate it.
So, for testing purposes, does anybody have a suggestion about how to resend (or fake resending) a received message to myself without altering its header info?

What matters is whether the Message is Junk
Mail condition would still evaluate to true
regardless.
That depends on what you are trying to determine & if the test produces decisive results.
For instance, consider tests with the standard Junk Filter automatic settings & no other rule involving "Message is Junk Mail" in the list. A test is performed in an attempt to determine if the filter's conditional tests are performed in the indicated order only until one evaluates to false.
"Send Again" should not cause the "Message is Junk Mail" test to be evaluated at all, since in this case the sender is oneself & the Junk Filter should exit as soon as the 'sender not in Address Book' test is evaluated.
Yet, when I try this with a message (correctly) marked as junk when originally received, the resent version is still marked as junk, & this happens not just on my on Mac but on the few others I have checked as well. I have tested with only a limited number of junk messages because on the other Macs the owners do not keep them for long & on my own I do not get that many (AOL is my primary account & has excellent spam filtering), so I would love to know if readers of this topic see similar results.
BTW, I should mention here what might be a potential hazard of using "Redirect" for testing with "real" spam: As I hope everybody knows by now, it is a bad idea to enable automatic loading of remote html images because doing so can alert spammers one's email address is valid. In one case, when I tried the "Redirect" method on my own Mac, AOL refused to accept the redirected message, possibly because of AOL's spam filters. At that point, Mail displayed the message, asking if I wanted to try sending it from another account, edit it, or what. Even though I have the option disabled, Mail loaded the original's remote html images along with its other content. I don't know if that is a design feature of Mail, a problem with just my Mac, particular to AOL, or what, but I want readers to be aware of it, just in case.
Anyway, for this reason I have since confined myself to testing with "Send Again," which seems safe in all cases, & mostly to testing only on my on Mac, just in case it is not.
Back to the "so what" aspects of this topic: It may be that the "Message is Junk Mail" test is sometimes treated differently from the other conditional tests in the Junk Filter in that it may be evaluated first or even if other tests before it evaluate to false. This makes some sense as a design feature in that even if the Junk Filter's automatic mode action isn't performed, it gives users more training opportunities. It may be a bug. It may just be something particular to my Mac. It may be something else, perhaps having to do with trusting junk headers, or something more subtle as yet unconsidered.
In any event, the point is holding all variables save one constant in any single "black box" test of a multi-variable system is a necessity for definitive results because variables may be interdependent. Because of this, the ability to resend to oneself the same message in unaltered form would be useful for a variety of tests, so I would still like to know if anyone has any ideas about how to do this.
iMac G5/2.0 GHz 17" ALS (Rev B) Mac OS X (10.4.7) 512 MB RAM, Kensington Trackball

How to test BLOB Table Column in BCBrowser??

Hi,
My requirement is to upload a file(pdf,doc,jpg, txt) into DB using ADF.
I use, Jdev 11.1.1.6, Oracle 10g XE.
For this, I created the following
1. A table as MyFilesTab(ID Number, FileName Varchar2(80), File BLOB)
2. An Entity Object MyFilesEO on MyFilesTab.
3. Generated a default view object: MyFilesVO
4. Application Module : TestAM with view instance "MyFiles"
But When I run TestAM, I see MyFiles as an Input textbox. So I cannot able to add a file that will be stored in my Table.
Please help me out.

Just to clarify, my previous post is related to title of this thread("How to test BLOB Table Column in BCBrowser??"),
and not to "My requirement is to upload a file(pdf,doc,jpg, txt) into DB using ADF"
Dario

How to test Process chain in BW

Hi Guys,
Can U give me some introduction to Process chains and how to test it in BW 3.5
Thanks for Ur time.
Cheers
Senthil

Hi,
A process chain is a defined sequence of interdependent processes required to perform acomplex task in an SAPBW environment. Data maintenance tasks in SAPBW are notrestricted to uploading data. Aggregate rollups, index maintenance, master data and ODS activation, and a variety of other jobs are required to update data, guarantee best-possible performance, and maintain data integrity. Typical SAPBW implementa-tions have complex interdependent networks of jobs in place that run every night, week,or month.Previous releases of SAPBW did not provide an integrated solution for scheduling and monitoring those kinds of job networks. This has changed with the introduction of process chains in release 3.0. Process chains allow you to define complex job networks consisting of standard SAPBW jobs, as well as custom jobs; they support visualizing the job network and centrally controlling and monitoring the processes.
(from "Mastering the SAP BIW")
New Features in BI 2004s Process Chains
/people/mallikarjuna.reddy7/blog/2007/02/08/new-features-in-bi-2004s-process-chains
Designing
/people/vishvesh.bahirat/blog/2006/11/29/bw-process-chain-design
Process chain creation in 2004s - step by step
/people/juergen.noe/blog/2008/01/11/process-chain-creation--step-by-step
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/events/sap-teched-03/using%20process%20chains%20in%20sap%20business%20information%20warehouse
Testing
We need to test the PC chains.
You need to test if the extractions are working fine, data is getting loaded into targets, post load activities like activation, rollup, compression etc are successfull etc.
We schedule / trigger the chains and monitor them. We ensure that all the process types are happening successfully.
One major area we concentrate on is to identify dependcies in the chain. This will ensure less erros and also reduce chain timings by a great extend. Dependencies should be kept to a minimum whereever possible.
Also in cases where we use events/third party shceduling tools to trigger BW chains we check that out.
Thanks,
JituK

How to test the adapters

hi
anybody can tell me how to test the adaptors?
regards,
krushi

Adapter Monitoring:
Steps:
1. Go to RWB.
2. In the Component Monitoring Select Adapter Engine
3. Select the Adapter Monitoring Tab.
Using this window u cam monitor
>> Installed and Started Adapters
>> Adapters with Error and
>> All the Adapters
Uses:
>>The name of the server on which the selected Adapter Engine was deployed. This can be a server cluster consisting of several nodes.
>>The namespace in which the adapters shipped by SAP are located. If you have created additional namespaces for your own developments or for third-party adapters, these are also displayed.
>>A list of all the adapters available for the selected Adapter Engine. Adapters that are not installed and started, or not registered with the Adapter Framework are GRAYED out. You can select all the other adapters to display additional information. i.e U can see all the Adapters.
If all the adapters are working then it will be displayed in GREEN.
If not then it will be displayed in RED.
If U are not using the adapters in ur scenarios then it will be GRAYED out.
Remember to set the thread to solved when you have received a solution
Use a Good Subject Line, One Question Per Posting - Award Points

How to test XI project..

1.How to test xi projects?
2.then how to test our scenario? Is there any testing tool is available to test the scenario?
3. What is CCMS? how it is useful in XI ?
Thanks in advance
Rakesh

Hi Rakesh,
+1.How to test xi projects?
2.then how to test our scenario? Is there any testing tool is available to test the scenario?+
XI is about messaging. So the way to test an XI implementation would be to test the messaging. Two options for doing that...
1. Test the implementation without the Application systems. The plain J2SE adapter really comes in handy here. You can use it to send an XML file to the Integration Server, check whether it is getting through the pipeline as intended (which means the routing, the mappings, etc), and let it pop out to a file somewhere. You can check all the steps the message has gone through from the XML monitor (sxmb_moni).
2. Test the actual implementation with the application systems. For this you would use the testing tools of the application itself.
I do not know of any automated tools for testing XI configuration, or any way of testing it without actually sending a message across.
What is CCMS? how it is useful in XI ?</b>
I can give you some info regarding CCMS, but the rest will try finding out and let you know soon. Mean while pls go through this info on CCMS.
When CCMS is not configured you can only do individual monitoring.
To configure the same you must decide which system is to be the central system for the SCR.
To know what SCR is and to know more about it please go through this link.
https://help.sap.com/saphelp_nw04s/helpdata/en/1e/ec9e38f0d92936e10000009b38f8cf/content.htm
After doing the same please follow these steps.
Log on to the system that is to contain the central repository.
- Choose CCMS ® Configuration ® Alert Monitor, or call transaction RZ21.
- Choose Technical Infrastructure ® System Repository ® Set Repository Role.
- The system displays the Set Repository Role in Central System Administration screen. Choose Central Repository.
And also go through the following links. This I guess will help you solve your problem and I guess it answers your question.
https://help.sap.com/saphelp_nw04s/helpdata/en/e5/15a0380d134f6fe10000009b38f8cf/content.htm
/people/sap.india5/blog/2005/12/06/xi-ccms-alert-monitoring-overview-and-features
/people/sap.user72/blog/2005/11/24/xi-configuring-ccms-monitoring-for-xi-part-i
Regards,
Abhy
Message was edited by: Abhy Thomas

ICal Server email invitations - how to test and get this feature working

iCal Server email invitations - how to test and get this feature working
Thanks Apple for introducing this nice little feature into iCal but then completely neglecting to write any sort of useful manual that can explain what to do when it doesn't work after you set it up for the first time.
At long, long last we have finally got there after about 6 months of fiddling on and off, so I thought I had better post up the process since many have similar issues and it is hard to ascertain what is going on.
Using an external email server was just a waste of time and it still wouldn't handle the replies properly even though it was supposed to handle '+addressing'. In the end I set up a special gmail account for the iCal server and finally got it working. I list here the process of configuring and testing the system to check that each little stage is working.
Set up a Gmail account in Apple Mail to access and test in the usual way for any email account (e.g. [email protected].);
Set the iCal server email to access the same email using the following settings:
IMAP
SMTP
[email protected]
smtp.gmail.com
Port: 993 [x] Use SSL
Port: 587 [x] Use SSL
User & Pwd
Login
User & Pwd
To test the settings:
send out a test email from Apple Mail to a non-server email address that you can access to check it has been received;
send out a test email from your non-server email account to [email protected] and check that it is received;
this tells you that the GMail account is setup correctly and working
Testing iCal:
I noted that iCal was deleting any emails that arrive in the inBox in Apple Mail as soon as they arrived (this is to be expected);
test that the invites are being sent from iCal by setting an event in iCal and inviting your non-server address (you may not see any sign of this in Apple Mail but you should catch it in the iCal server log and possibly in the Gmail sent mail box);
check that the invite is received at your non-server account and Accept it in iCal on another machine - the reply is automatically sent back;
the replies appear in Apple Mail but are quickly deleted by iCal. But their record for you to see is left in Gmail under 'All Mail';
Accepted invites appear as a notification button on the top left hand bar on iCal where you click to acknowledge them and then the attendee is shown as a green circled tick instead of a grey circled ?.
this shows that iCal invitations are working correctly. Whenever an event is updated, all invitees should be updated by email automatically.
I hope this helps anyone - I could certainly have done with something similar when I started with looking at this.
Anatole
The Error and Access logfile in the Server app under iCal server are very useful in determining any errors. I got lots of imip errors when I didn't quite have the settings right. The port is critical and it won't tell you this is the problem if it fails.

iCal Server email invitations - how to test and get this feature working
Thanks Apple for introducing this nice little feature into iCal but then completely neglecting to write any sort of useful manual that can explain what to do when it doesn't work after you set it up for the first time.
At long, long last we have finally got there after about 6 months of fiddling on and off, so I thought I had better post up the process since many have similar issues and it is hard to ascertain what is going on.
Using an external email server was just a waste of time and it still wouldn't handle the replies properly even though it was supposed to handle '+addressing'. In the end I set up a special gmail account for the iCal server and finally got it working. I list here the process of configuring and testing the system to check that each little stage is working.
Set up a Gmail account in Apple Mail to access and test in the usual way for any email account (e.g. [email protected].);
Set the iCal server email to access the same email using the following settings:
IMAP
SMTP
[email protected]
smtp.gmail.com
Port: 993 [x] Use SSL
Port: 587 [x] Use SSL
User & Pwd
Login
User & Pwd
To test the settings:
send out a test email from Apple Mail to a non-server email address that you can access to check it has been received;
send out a test email from your non-server email account to [email protected] and check that it is received;
this tells you that the GMail account is setup correctly and working
Testing iCal:
I noted that iCal was deleting any emails that arrive in the inBox in Apple Mail as soon as they arrived (this is to be expected);
test that the invites are being sent from iCal by setting an event in iCal and inviting your non-server address (you may not see any sign of this in Apple Mail but you should catch it in the iCal server log and possibly in the Gmail sent mail box);
check that the invite is received at your non-server account and Accept it in iCal on another machine - the reply is automatically sent back;
the replies appear in Apple Mail but are quickly deleted by iCal. But their record for you to see is left in Gmail under 'All Mail';
Accepted invites appear as a notification button on the top left hand bar on iCal where you click to acknowledge them and then the attendee is shown as a green circled tick instead of a grey circled ?.
this shows that iCal invitations are working correctly. Whenever an event is updated, all invitees should be updated by email automatically.
I hope this helps anyone - I could certainly have done with something similar when I started with looking at this.
Anatole
The Error and Access logfile in the Server app under iCal server are very useful in determining any errors. I got lots of imip errors when I didn't quite have the settings right. The port is critical and it won't tell you this is the problem if it fails.

How to test a class with array which is being declared?

Dear All
I am doing a question which involved the day of the week.
I had written a class which is name WeekDay and here is the code :
public class WeekDay
private int index;
private static String[]dayStrings = {"Sunday","Monday","Tuesday","Wednesday","Thursday","Friday","Saturday"};
public WeekDay(int idx)
index = idx;
public int getIndex()
return index;
public static String nextDay(int index)
index+=1;
return dayStrings[index];
The above compile well with no issue.
Here is the problem which i need to seek your help, I had created a program to test the above program.
But I am not sure how to test it.
Here is what I had written :
public class TestWD
public static void main(String[]args)
System.out.println("Please key in a digit to get the day of the week\n");
System.out.println("Sun, Mon, Tue.....Sat is represented by 0,1,2,3...6");
int idx = Integer.parseInt(args[0]);
WeekDay wd = new WeekDay(dayStrings[]); // I can't seem to declare this line.
My question how can I test the above program ?? I can't seem to be able to declare a "wd" from WeekDay. The dayStrings wich i had declared in the WeekDay class is a String array. But how can I declare a suitable line in my test program in order for me to test my program?
What I wanted to do is to get the above line running and than I will proceed on to code it to display the day after a day...for example, if today is Wednesday and when I run the wd.nextDay(index). It will return me Thursday!
But I am not sure how to declare the above...please enlighten me.
Thank you.

Hi
Thank you for helping but when I compile my program. It seem fine but when I execute it, it prompt me with an error message :
code}public class TestWD
public static void main(String[]args)
System.out.println("Please key in a digit to get the day of the week\n");
System.out.println("Sun, Mon, Tue.....Sat is represented by 0,1,2,3...6");
* int idx = Integer.parseInt(args[0]);*
WeekDay wd = new WeekDay(idx);
System.out.println(wd.nextDay(idx));
}{java.lang.ArrayIndexOutOfBoundsException: 0
at TestWD.main(TestWD.java:8)
Edited by: SummerCool on Nov 1, 2007 2:53 AM

How to Test "NoSuchFieldException" Using if {} else{}?

I have a line of code in a loop:
Field column = DownloadChildClassColumns.class.getDeclaredField(id);The above code throws "NoSuchFieldException" for certain "id"s in the "getDeclaredField" method. If it happens, I have to get the Field from another class:
Field column = DownloadParentClassColumns.class.getDeclaredField(id);How do I test using if {...} else {...}. That is, if a certain Field is unavailable in one class, then get that Field in another class?
Thank you for your guidance.

JavaLaptop wrote:
I might not get the idea. Sorry, my head is as hard as a stone sometimes.
If I use the "getDeclaredField( id )", I still can get the "NoSuchFieldException".
My problem is "how" to test out if certain Field is not in one class then I go to another class to get it.Do the second test in the catch clause dependant on the first e.g.
Field field = null;
try {
    field = class1.getField("fieldName");
} catch(NoSuchFieldException ex) {
     try {
       field.class2.getField("fieldName");
      } catch(NoSuchFieldException ex2) {
         log.error("No such field as fieldName");
         throw new IllegalStateException("fileName not found in either class");
   }

How to test the Siebel Applications ? (very urgent and important)

**Hi Pals,**
**I am suresh from Noida, I work for GLS in Testing department.Presently we have a project of Siebel Analytics (OBIEE).We hav to test the siebel applications now.I kindly request u all to clarify my doubts regarding this.**
**1.What is Siebel or OBIEE testing ?**
**2.How to test these applications ?**
**3.Basic process of Siebel testing ?**
**4.Tools Used to test these applications ?**
**5.What is STA (Siebel Testing Automation) ?**
**6.Where can I find the usefull documents relating to this.**
**Help me out guys, it's very important and urgent.I will be very much thank full to u all if u do the same.....Anticipating a quicker response.**
**Thank u.**

Welcome to the [top 10|http://forums.oracle.com/forums/thread.jspa?messageID=3928667#3928667]!
Cheers,
C.
PS: [http://catb.org/~esr/faqs/smart-questions.html]

How to test if a number is prime?

Hi, I'm doing an exercise. I'm iterating through numbers from 2 to 100 (since 1 is not a prime number) and I need to test if the current number is a prime, if it is print it out. But I can't figure out the condition, how to test if a number is prime? So far I got this, but it prints all subsequent numbers, which is now obvious to me, but how to test for primes?
public class Main {
    public static void main(String[] args) {
        for (int i = 2; i <= 100; i++) {
            //Test if a number is a prime, if it is print it
            // The (i + 1) is because I want to divide i by any other number, so I thought i + 1
            if (((i % i) == 0) && ((i % 1) == 0) && ((i % (i + 1)) > 0)) {
                System.out.println(i);
}

Aardenon wrote:
I understand your point. But it seems unsafe to assume a number from which the checks are unnecessary. That could lead to an error. I'm sure it is mathematically provable somehow, but I'm not that good in Math. I mean to write a safe (and optimized) version of the code, I would still have to go through all uneven numbers and 2.Nope. In fact, for an optimized version, definitely not; however, I wouldn't worry too much about optimization at the moment.
One little tip I remember from school, back in the dark ages, is that all prime numbers other than 2 and 3 have the form 6k ± 1. That is NOT to say that all such numbers are prime, but it does eliminate a lot of the ones you need to check.
You might also want to check out the [url http://en.wikipedia.org/wiki/Prime_number#Verifying_primality]Wikipedia page on prime numbers; it's very good.
Winston

How to test if TV-Out (VIVO) is defective?

Similar Messages

Maybe you are looking for