How will i link flowmeter sensor and labview

Hello everyone,
I am new in this forum and alson in labview.I have a flowmeter sensor, I made cable connections bewteen the sensor and DAQ(NI-USB 6229) The question is what am i supposed to do to read the data on sensor.I just want to measure read the flowmeter sensor and dont know how to construct the labview diagram.I searched on net and learned that I have to do something with counters to convert square signal to a grapgh.and also I searched some codes about it but there must be an easy way to do this it ooks too complicated.In attachment I am sending the vi file.
Can you please help me because I have limited time..
Thanks in advance.
Attachments:
seyfi.vi ‏62 KB

Why did you attach a VI that writes out an analog output rather than a VI that actually reads in a signal?
What type of signal is the flowmeter putting out?
Did you look in LabVIEW help? There are dozens of examples there for reading different signals using DAQmx.

Similar Messages

I need to reinstall my LR4 software. How will this affect my catalogs and plugins?

I need to reinstall my LR4 software. How will this affect my catalogs and plugins?

Explain further: "lost the ability to turn on control points to readjust levels on the wand"
Are you referring to the Adjustment Brush tool? Or something else?
Are you stating that you cannot see the pin (is that what you mean by "control points"?) at all (if so, then press letter H) or are you stating that pressing H doesn't work? Or something else?

How I can link back video and audio after I unlink them

how i can link back video and audio after I unlink them

In what program? You may wish to ask such specific usage questions in the product forum for whatever tool you are referring to...
Mylenium

How do I link Photo Title and Photo Caption in iPhoto Book

When using the yearbook template in iPhoto I have found that the Title is not linked to the photo Captions are linked most of the time, so if I move a photo I have to reset all the titles. How can I link them?

hi Jim,
Are the titles that are not moving ones that you gave the photos while you were in the book mode?
I was just wondering if you gave the titles to the photos in the library view if it would work differently.
Ok, I just tested it. Before you make the book, give all the photos the correct titles and comments if any. Now highlight that album and choose to create a book. The titles and comments will move with the images this way.
I also tested an image that was already placed in the book and it had a title that it was imported as. I changed the title in the library view, went back to the book and moved the photo. The title that I just gave it in the library view moved with the photo.

How do make link between query and UDF

How do you link a query to your UDF after you created the query and the UDF?
Also do you have to set the UDF as type "general", and "link"?
Please take me thru step?

oh good - a discussion about whether to use "link" or "image" when having an image connected to a product!!!
Billy and Suda - We had fun with this one some time ago in a project collecting additional data and images for the customer's products on the market. As we were ramping up the project, we tried both ways of connecting an image to a product and there was a few drawbacks we found with using the UDF type of "General" and "Image":
1. The image was placed directly on the UDF portion on the Item Master - they were working in large TIFF (?) formats and the picture just looked horrible. The approving manager could not tell if the image should be approved for press or not. When he double-clicked on the image in the UDF portion it brought up another SAP window that wasn't quite crystal clear.
2. The image took up so much room on the UDF portion of the Item Master that the data entry personnel had to constantly scroll down to enter the other data points (color, size, branded promo, mixture, etc - there were about 12 fields). Talk about being ticked!
3. While using the "General" and "Link" it addressed those concerns BUT there was one extra enormous advantage with this General/Link method. When the image was brought up, it opened up the image automatically in a standard picture editor/manager program. If they liked what they saw, they continued foward with the approval of the image for press runs. If they did not like the image, they were able to manipulate the image at the moment and then follow through with approval (time saver for sure!).
I am sure it all boils down to what the customer requirements are, but some other clients I demoed this to wanted to switch immediately after seeing that! But definitely something to think about if you are planning on connecting an image to a product...
Oh and she really is correct, Billy - I have never heard of anyone linking a query to a "link" or "image" type...I don' t know how you would even do that as the "link" or "image" selection leads you directly into the attachment and/or storage path and location...
take care - Zal

Datasocket: link between java and labview

Hi,
I would like to link java and labview for a real time animation and i would like to use datasockets.
Can somebody proficient in using datasockets help me out.
My email id is [email protected]
Thank u.
jagadish.

The person who wrote the book (literally) on LabVIEW and Java is Jeffrey Travis. His book "Internet Applications in LabVIEW" has examples. His web site is here. You can also get the book on Amazon.

How do I link my IPad and IPhone so I can use my IPhone as a hub?

How do I link my IPad to my IPhone so I can use my IPhone as a hub when I don't have access to Wi-Fi?

iPad and iPad mini User Guide (For iOS 6 Software)
Share an Internet connection: Go to Settings > General > Cellular and tap Set Up Personal Hotspot —if it appears—to set up the service with your carrier. After you turn on Personal Hotspot, other devices can connect in the following ways: • W-Fi: On the device, choose your iPad from the list of available Wi-Fi networks.
iOS- System requirements for Personal Hotspot
iOS- Understanding Personal Hotspot
iOS- Troubleshooting Personal Hotspot

How to distinct real Kinect sensor and .xef playback source

Hi there,
I’m making an application which compare a live motion(f.e. body frame) captured by the Kinect sensor and a playback xef file recorded by KStudio, I
wanted that they display in two different canvas, but my difficulty is that how to know the frames come from the sensor or the xef file, now all frames display on all the canvas simultaneously.
Thanks in advance for your help.
Haishan

hi jmmroldan,
Thanks for your reply and ideas.
The StartRelativeTime is readonly, so I can't put personal information in it.
Actually, my application is a dance comparaison, uses can learn and imitate from a pre recorded video(color and body frame).
The scenario is quite simple
- Record the "teacher" 's frames to xef file by using the KStudio of Microsoft.Kinect.Tools.
- Play this xef file in a litte windows
- Display the live captured data in the main windows.
for this, I create two FrameReader to listen the FrameArrived event.
I noticed that inside the KStudioPlayback or KStudioRecording class, there is a method called "GetMetadataForStream", but I don't know how to create then use it, and I'm not sure I can retrieve it from
the captured data by Kinect Runtime.

How to control valve via PCI6023E and labview

I have a PCI6023 board and labview 5.1. I need to control the opening/closing of a gas valve via these two.The problem is that the power needed to operate the valve is 24 volts while the PCI6023E board has the power of only 5V. What can be done? Please help.

Run a secondary power supply to the valve via a transistor triggered by the DAQ board. You can get a cheap AC/DC wall plug in supply for a coupla bucks and transistors are a few cents.
/ <---- 24V2Collector
|
DAQ2Base----->|
|
\ -----> Emitter2valve
2006 Ultimate LabVIEW G-eek.

What is the link between PLC and Labview

provide me details regarding Subtitution of scada with labview

Lots of details if you follow this link:
http://ni.com/labview/labviewdsc/what_is.htm?node=10418
=====================================================
Fading out. " ... J. Arthur Rank on gong."

How to break link between iWeb and web gallery?

I have created an external webpage with the use of iWeb, and I have inserted the photos widget through the web gallery which sits on my personal .Mac account (ie. different to the external website which has an independent - no mac - .com address)
I would like people to view the picture widget on the external website (a business website) I have created, but I do not want them to click on it and then be directed to my home web gallery. Basically I just want them to be able to see the rolling pictures, but nothing more.
Does anyone know how to avoid this link from working?

Hi Kodi,
As far as I know, the object link to material is part of SAP standard customer delivery. Then there is really small customer settings you have to maitain, actually the fields Destination and Web server, as the SAP never knows the name of the system, which customer will use.
Or you talk about others than the 0PLANTMATERIAL, 0PLANTMAT_LONG. If you create new object link type, the install guide 'Collaboration Projects (cProjects): Guide Impl. Object Link ' in the https://websmp105.sap-ag.de/plm-inst should give you detailded information.
Kind regards,
Zhenbo

How to create links between SO and PO's

Basicly the subject tells the question, how can you create links between Sales orders and Purchase orders? Sounds simple but how to do it?

Hi,
You can may be do the easy way out then,
1) Open the Sales Order for which you have created the Procurement Document.
2) Go to the 'Form Settings' of the Sales Order and 'Table Format'.
3) In the list, select the Procurement Doc field and make it visible.
You will be able to see the Procurement Document for the Sales Order raised without using the query.
Check if this is what you are looking for and the same helps.
Kind Regards,
Jitin
SAP Business One Forum Team

How to configure link between 2921 and SM-D-ES3G-48-P EtherSwitch Service Module

hi,
I can't do that like the procedure given by Cisco.
http://www.cisco.com/en/US/partner/docs/routers/access/interfaces/software/feature/guide/eesm_sw.html#wp1942894
Cisco Procedure :
interface gi10/0
ip address x.x.x.x x.x.x.x
service-module gigabitethernet 1/0 session
My result :
R2921-8CPITR-1(config)#int gi 1/1
R2921-8CPITR-1(config-if)#ip address 2.2.2.2 255.255.255.192
% IP addresses may not be configured on L2 links.
R2921-8CPITR-1(config-if)
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1.1 ?
% Unrecognized command
R2921-8CPITR-1(config)#interface gigabitEthernet 1/1 ?
<cr>
R2921-8CPITR-1(config)#
the session is not possible also ?
R2921-8CPITR-1#service-module gigabitEthernet 1/1 sess
                                                  ^
% Invalid input detected at '^' marker.
R2921-8CPITR-1#
The routeur said that it's not a L3 port, so how to configure it to allow communication between the 2921 and the card ?
Is there a bug with that version I'm in 15.1(4)M4 ????
R2921-8CPITR-1#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 20-Mar-12 18:57 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M15, RELEASE SOFTWARE (fc1)
R2921-8CPITR-1 uptime is 19 hours, 21 minutes
System returned to ROM by power-on
System restarted at 16:00:45 GAB Fri Sep 14 2012
System image file is "flash0:c2900-universalk9-mz.SPA.151-4.M4.bin"
Last reload type: Normal Reload
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FGL1618119E
6 Gigabit Ethernet interfaces
2 terminal lines
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device#   PID                   SN
*0        CISCO2921/K9          FGL1618119E
Technology Package License Information for Module:'c2900'
Technology    Technology-package           Technology-package
              Current       Type           Next reboot
ipbase        ipbasek9      Permanent      ipbasek9
security      None          None           None
uc            None          None           None
data          None          None           None
Configuration register is 0x2102
R2921-8CPITR-1#

Same issue here.
I just waited a few minutes and the interface went down and back up, this time it was a L3 interface.
My guess is that it was booting the switch module IOS, and it detected it until it was fully booted:
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:52.091: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:26:52.795: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/2, changed state to down
Apr 11 05:26:53.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface Embedded-Service-Engine0/0, changed state to administratively down
Apr 11 05:27:46.895: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to administratively down
Apr 11 05:27:46.947: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
Apr 11 05:27:47.031: %LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to administratively down
Apr 11 05:27:47.083: %LINK-5-CHANGED: Interface GigabitEthernet1/0, changed state to administratively down
Apr 11 05:27:47.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Embedded-Service-Engine0/0, changed state to down
Apr 11 05:27:48.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to down
Apr 11 05:27:49.283: %IP-5-WEBINST_KILL: Terminating DNS process
Apr 11 05:27:52.499: %LINK-3-UPDOWN: Interface GigabitEthernet1/1, changed state to up
Apr 11 05:27:53.087: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2951 Software (C2951-UNIVERSALK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 04-Sep-12 16:50 by prod_rel_team
Apr 11 05:27:53.255: %SNMP-5-COLDSTART: SNMP agent on host Router is undergoing a cold start
Apr 11 05:27:53.499: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to up
Apr 11 05:28:21.435: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Apr 11 05:29:22.091: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to down
Apr 11 05:29:22.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down
Router>en
Router#sh ip int brief
Interface IP-Address OK? Method Status Protocol
Embedded-Service-Engine0/0 unassigned YES unset administratively down down
GigabitEthernet0/0 unassigned YES unset administratively down down
GigabitEthernet0/1 unassigned YES unset administratively down down
GigabitEthernet0/2 unassigned YES unset administratively down down
GigabitEthernet1/0 unassigned YES unset administratively down down
GigabitEthernet1/1 unassigned YES unset up down
Vlan1 unassigned YES unset down down
Router#
Apr 11 05:29:46.106: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/1, changed state to upconf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int g1/0
Router(config-if)#ip add 1.1.1.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#
Apr 11 05:30:09.046: %LINK-3-UPDOWN: Interface GigabitEthernet1/0, changed state to up
Apr 11 05:30:10.046: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0, changed state to up
Router(config-if)#end

How to I link Slaes Orders and Price Assurances - Table VBAK Field AUART

Hello,
Using T-code VA43 I can enter a contract number (we call it a Price Assurance#) and then I can see the information I need 1 for one. I can also pull this info out of the VBAK and VBAP tables using the doc type ZQ in the field AUART. What I am trying to do is link all of these document types to their sales orders, AUART=TA, and then finally link them to the invoices but I am having trouble doing it. Can someone help me figure out how to link the sales documents types ZQ to their corresponsing TA types? From there I can link the billing documents to them.
Thanks,
Sean

Hi Sean,
As per my understanding of your question is about copy controls,where you copied the standard quantity contract type CQ and
named it as ZQ,now you want to link it up with order type TA(Standard Order),for this you need to maintain copy controls
between your contract and order.Use T.code VTAA select your contract type and sale order type maintain copy controls *(copy
standard CQ - TA and rename it as per your document type) the you need to maintain copy controls between TA to LF use
T.code VTLA the delivery to invoice use T.code VTFL.
Search in Forum or Google for better understanding of copy controls.
Regards
Ram

How will the new fingerprint sensor affect protective cases?

I currently have the Otterbox Defender on my iPhone 5, and I really like it. However, I can't see how a case like that would work with the new fingerprint system. I would really like a case with a screen protector, and raised edges on the outside so that the screen doesn't touch the ground when laying facedown. Does anyone know if any such cases will be developed?
Also, does anyone know if it matters what finger you use? I've only seen a few pictures, and they all show the index finger; I'd really prefer my thumb.
Thanks!

Oh, haha, I see what you did there... Ok.
I don't actually have an upgrade on my plan until January, so sadly I won't be able to put out any helpful information in a reasonable amount of time...
Thanks again, though.

How will i link flowmeter sensor and labview

Similar Messages

Maybe you are looking for