HT4437 I have followed all relevant steps, my iPhone5 and apple TV are connected to the same wireless network, but I still cannot use airplay. When I choose the airplay option on my phone, the only option I get is "iPhone"
I have followed all relevant steps, my iPhone5 and apple TV are connected to the same wireless network, but I still cannot use airplay. When I choose the airplay option on my phone, the only option I get is "iPhone"
Welcome to the Apple Community Willy.
Try the following steps, check whether things are working after each step where appropriate, before trying the next.
Check AirPlay is turned on on the Apple TV (turn it off and on if it already is)
Check that both devices are on the same network (Settings > Wifi, on the mobile device and Settings > General > Network, on the Apple TV).
Restart the Apple TV (Settings > General > Restart).
Restart the Apple TV by removing ALL the cables for 30 seconds.
Restart your router. (Also try removing it’s power cord for at least 30 seconds)
Restart your mobile device.
Similar Messages
-
I am trying to connect my printer, canon MG3170, it has been connected to the same WIFI network, but I still showing "no airprint printers found". I have tried to restart the printer few times but still the same. Please help, thanks (Dhoni-Singapore)
power everything off printer & router.
re-boot ipad.
Press and hold the Sleep/Wake
button until a red slider appears, then drag the slider. Then press and hold the Sleep/Wake
button until the Apple logo appears. page 128 iPad user manual.
more details on re-booting:
http://ipad.about.com/od/iPad_Guide/ss/How-To-Reboot-Your-iPad-Power-Off.htm
power on router then printer then ipad
Cross your fingers.
Robert -
I have reinstalled Itunes 10.4 .1 10. windows says drivers are not installed. I have followed all trouble shooting advice, fixes and updates for windows 7
I have reinstalled Itunes 10.4 .1 10. windows says drivers are not installed. I have followed all trouble shooting advice, fixes and updates for windows 7
-
I have an iPhone 5. It says I have 537 songs on it but every song shows the cloud icon. I have gone through every suggested step I've googled and deleted songs but settings still shows them. When it's plugged into my mac itunes shows it only has 42 songs.
Hi ellafromva,
From your description, it sounds like you may have iTunes Match activated; you may find the following article helpful:
Apple Support: iTunes Match on iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT5637
Regards,
- Brenden -
I switched ISP a few days ago and had problems with airplay since. After restarting and reinstalling and updating, re entering pass keys for new wi fi on everything, Apple TV shows: Your Apple TV is connected to your wi fi network but cannot connect to the Internet. Ipad3 and iPod touch 3G have no airplay icon or get one briefly then it disappears again. Same with itunes on windows laptop.
Can anyone help?
BobWelcome to the Apple Community.
Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment. -
I made a new playlist on ituns and changed the format to MPS, but I still cannot get it moved to my SD in that format...help?
Ok, so you said you've already right clicked on each song and "created a MP3 version?"
If so sort the library's music by "Date Added (if it is not there right click on the other sort bars and add the column "Date Added". The mp4 versions are the ones in the playlist. You will have to find the newly added mp3s by sorting by Date Added. Hope this helps! -
How to connect 2 apple TV to the same wireless network?
Hi,
Can somebody please help me shed some light here on how to connect 2 ATV to the same wireless network? My first ATV connected to the network just fine and syncing with my itunes, however the 2nd ATV keeps getting problem connecting to the network everytime I tried to connect to the network. It detected my home network on Linksys router just fine, but it wont connect to it.
Hope someone can help me out here... Thanks peeps...Hm ive make sure all the password and everything is correct and yet it wont connect. Keeps getting the problems connecting to the network, please check your setttings.
-
I currently have a WPN824 v3 Netgear router and I’m trying to set up my Apple TV. I am able to connect it to my wireless network but my airplay feature is currently not working. The icon does not appear on any of my devices. My ipad and ipones all are currently up to date and are all joined to the same network. Is it the way that my router is configured. Please help let me know what I need to change in my router settings or does my router not work with Airplay. Or is there a simple fix.
you don't mention which products you use
only ipad2 and up support mirror
and only iphone4s and up support mirror
other devices only use airplay for apps which support tvout options -
My ISP requires a http login. I can use the iPad fine if I am logged in on a PC connected to the same wifi network, but if I login on safari on my ipad, the connection drops after some time.. any workaround?
TJBUSMC1973 wrote:
The iPhone is working, as designed and advertised. In this case, the user failed to educate themselves properly, either by proper research or asking the right questions, before purchasing the device.
I understand that the OP failed to do research. But then, I wasn't replying to the OP. I was replying to Chris. I have Verizon. I can talk and use data at the same time with my Droid Maxx. Therefore, the problem is not just with the network. It would be technically possible for an iPhone to do that on Verizon/Sprint if Apple had chosen to use a different chip, such as the kind other phone manufacturers have elected to use.
Of course, this is probably all irrelevant to the OP's issue. It was merely a point of clarification, especially for those people who are used to being able to use both voice and data at the same time on Verizon. When they switch to an iPhone, they are often surprized at the limitation.
Best of luck. -
Is the maximum number of users for Airport Extreme per device, i.e. 2 AEBS = 100 users, one AEBS extending the other on the same wireless network?
50 users per device, assuming that the "main" router is setup to deliver an adequate number of network IP addresses for all devices.
2 AEBS = 100 users, but that is really more of a theoretical max.
If you really need 100 connections, it would be much better to use 3 AEBS to spread things out. -
How do I share files between computers (mac's) on the same wireless network?
How do I share files between computers (mac's) on the same wireless network?
Turn on File Sharing in System Preferences - Sharing, then you should be able to see them in the other Macs' Finder sidebars (under Shared). Click on them, click Connect As, and log in with the user credentials you're sharing from.
Matt -
Is there a way to play on the same wireless network with 2 different xbox 360 accounts?
Is there a way to play on the same wireless network with 2 different xbox 360 accounts?
Not sure what your question has to do in respect to Apple networking, but if you're asking can you use your Xbox 360 on a wireless network (regardless of the router's manufacturer) to access different Xbox Live! accounts, then the answer is yes.
-
Just trying to restore my phone, and i have followed all the steps yet none of them have worked. any other ways to do this?
Placing your device into recovery (DFU) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
until the red slider appears, then slide the slider. Wait for the device to turn off.
* If you cannot turn off the device using the slider, press and hold the
Sleep/Wake and Home buttons at the same time. When the device turns off,
release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
device. The device should turn on. Note: If you see the battery charge warning,
let the device charge for at least ten minutes to ensure that the battery has some
charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
If you have a problem getting into recovery mode then try: RecBoot: Easy Way to Put iPhone into Recovery Mode.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.
If the above doesn't work, then take it in to an Apple retailer for help. -
Recently bought an album from itunes, all tracks downloaded but some require my laptop to be authorized, which it is.
I have followed all the recommended steps by Apple Support and none have worked.
Any help or suggestions very welcome.
Thank you!Delete and redownload them if doing so is free in your country.
(97227) -
Facebook says I need to enable cookies, but I have followed all your steps.
Facebook says I need to enable cookies in order to log in. I am using windows 8.1. I have followed all the steps in the support section and am still getting the same error message.
Note that your System Details list shows that you have a user.js file in the profile folder to initialize prefs each time Firefox starts.
The user.js file is only present if you or other software has created this file and normally it wouldn't be there.
You can check its content with a plain text editor (right-click: Open with) if you didn't create this file yourself.
The user.js file is read each time Firefox is started and initializes preferences to the value specified in this file, so preferences set via user.js can only be changed temporarily for the current session.
You can delete possible user.js and numbered prefs-##.js files and rename (or delete) the prefs.js file to reset all prefs to the default value including prefs set via user.js and prefs that are no longer supported in the current Firefox release.
*http://kb.mozillazine.org/Preferences_not_saved
*http://kb.mozillazine.org/Resetting_preferences
Maybe you are looking for
-
HP 7520 only prints half a page of A4 in microsoft word 2007
Hi, Using a new HP7520 all in one , it will not print a full sheet of text in microsoft word 2007 . In the print option area of word allows me to set different paper sizes and thats fine . but the default option is set to No Scaling . If I change
-
I believe I originally posted this topic in the wrong forum, so I'm adding it here.... I'm writing a Java program that computes the number of money denominations. I need to display the non-zero denominations only and display singular words for single
-
Using DAQmx PCI-6534? It will not convert from Traditional.
I am trying to convert my PCI-6534 from a traditional NI-DAQ Device to a DAQmx device using the conversion tool in Measurement & Automation Explorer. After it looks for devices, it says there is no Corresponding NI-DAQmx Device for the PIC-6534. Soft
-
I created a 'development' library file with labview development that includes ALL sub vi's. When I try to run it with runtime it says a sub-vi is not executable. I open it back up with development just fine and re-save it. It is still broken with run
-
Hi you nice people here, I wonder if someone can help with this problem I'm experiencing. First, a few days ago I installed a codec for a movie/3D program I'm using. I also did a full Music Analysis in Creative....... I tried to use What U Hear as pe