I am getting serious latency from my Zoom R16!

I am getting serious latency from my Zoom R16 interface since os 10.6.8 update, nothing else has changed, just the update. I've installed the supplimental update. No change. I've contacted Zoom, they believe it to be an Apple issue. From my naive perspective, I do, too.

This thread is being discussed here: https://discussions.apple.com/thread/3152729?start=0&tstart=0

Similar Messages

Getting 100-200ms latency from data rec'd to program action. Any ideas?

We are trying to isolate an apparent 100-200ms latency from data xmitted to NI485/4 and program response. Using win2k with virtually no CPU being used. Code appears to be well written and has system priority. We have Intel D845GBV2 board and have three PCI cards, NI485/4, Data xlation 3153, and I/O card.
I suspect PCI problems. The NI 485/4 works fine except for latency and installation shows no problems except for memory address conflict between each of the four ports, however I suspect this is not a problem as all four ports are on the same card.
Any suggestions?

Chris,
Thanks for the fast reply. I reloaded the driver (but did not physically remove card as of yet; system is installed in cabinet and not easily accessed). System shows card working properly under "Device Manager"; no exclamation points or other symbols show up on the ports. However, when I right-click and check properties| resources tab for any one of the used ports (three in my case)it shows the memory address as also being used by the other two active ports. I appear to be unable to change the memory I/O at this screen as settings are grayed out.
If you can confirm this is not a good situation, I will investigate further. Thanks again

I know I've heard that iPads/iPhones can't get viruses but is it possible that they can? While using my iPad, it keeps going in and out of apps. On Facebook, status and profiles keep getting clicked and it keeps zooming in and out. Can anyone help

I Have an iPad mini, iOS 8.1. When I'm on my iPad, it keeps going in and out of random apps. Going to settings is the worse. As soon as I click settings and it opens,it starts clicking different things and tries turning on and off settings! In Facebook, profiles and status get clicked. The screen zooms in and out multiple times. It reminds me of when you call the help desk for a computer or a computer at work and they gain access and move around clicking and you're doing nothing. Basically things are being clicked and I'm not doing it.....can anyone help?

At this point, I would go for reset to its factory default condition, using the iTunes program to get a clean system install. That way you'll clean everything out and just have it set up the way it would come from the factory. You'll need to do your backup (on the iTunes program too) and be sure you understand which stuff will be saved and which will not (from the links below). Also turn off any anti-virus program you may have on your desktop. Then when you reset it to the factory default condition, don't restore your backup just yet ... until you check it out without your data put back on it. Verify its operation first, to make sure that you know it's okay. Hopefully everything is okay at that point, otherwise you'll have to take it into Apple to check it out for any hardware failure.
Here are the links, and the last one pertains to the reset to factory default condition ...
Choosing an iOS Backup Method (Should I Use iTunes or iCloud to back up ...)https://support.apple.com/kb/HT5262
Back up and Restore your iOS Device with iCloud or iTunes
http://support.apple.com/kb/ht1766
iTunes: About iOS Backups
http://support.apple.com/kb/ht4946
Create and Delete iPhone, iPad and iPod Touch Backups in iTunes
http://support.apple.com/kb/ht4946
iOS: Troubleshooting Encrypted Backups
http://support.apple.com/kb/TS5162
Use iTunes to Restore your iOS Device to Factory Settings
http://support.apple.com/kb/ht1414

Is it possible to get the image from the i pad when mirroring via Apple TV to fill the screen instead of appearing as a screen within a screen?

When mirroring, is it possible to get the image from the ipad to fill the screen on the TV instead of appearing as a screen within a screen?

Welcome to the Apple Community.
No, the iPad has an aspect ratio of 4:3, a TV has an aspect ratio of 16:9, to fit one into the other is impossible without distorting the picture. If your TV has a zoom feature, you may be able to use this to fill the screen a little more to your liking, but this will result in cropping top and bottom.

Verizon rep told me that the tracking info doesnt matter until we get an email from fedex?

About 4 reps said the shipped/not shipped info doesnt mean anything but if it wasnt a pre order, when it would have shiped. And to not trust it until you get an email from fedex.
So everyone shouldnt worry if it says processing, you will still get it.
And for the ones that say shipped, dont get too excited until around the 7th lol.
I really wish verizon wireless in general would confirm this though.

iFreak22 wrote:
Really? When i pre order things that are shipped by fedex i always get a email when it is shipped and the tracking number works.
cathied wrote:
Did you call CS 4 times to ask the same question? I don't recall ever getting an email from Fedex for ANYTHING I've ever ordered online from Verizon or anywhere...unless I've requested on the fedex website to be emailed when I did the tracking...but I had the tracking # from the company I ordered from first.
Also, you may want to leave CS alone with the "when will this ship" business...there are people having computer issues trying to place orders and they're getting inundated with "when will this ship?" when the confirmations clearly say 2/10/11. If your order says it's been shipped then AT LEAST give it 24 hours to see if you get a tracking # before you call.
I mean seriously, most of us have waited for years for the iphone...can we wait just 1 more week?
You get an email from Fedex? Or from the company? I don't think I've ever received an email from Fedex directly...I've gotten emails from the company I'm ordering from with a link to the fedex website and the tracking info, but never from fedex...

Extremely high latency from 4am - 12pm in Baltimore, MD

Lately for the past month I have been getting extremely high latency 1500ms+. I am directly wired to the Actiontec router using a new cable on a confirmed working lan card. I believe the problem maybe at the POD card. How would I go about proving to Verizon without going through numerous transfers of people that don't have a clue?

I had the same problem since Mid-June. Seems like it's anywhere in North Eastern United States. I myself is located about 20 Minutes from Washington DC. I get the latency right around 12~50 ms on first hop to Google or verizon.net on a good day with trace route test. The people in Verizon tells me that's normal but I don't buy that because my neighbor gets around less than 20 ms, never higher. It gets progressively bad around prime time and onward. Around 12 AM it can reach from 100~400 ms on latency to Google or verizon.net server.
I am a late night gamer and need that low latency badly. Seems like most of the people I have talk to from FSC (Fios solution Center) had no idea what is the difference between Bandwidth to Latency. They just call it "Speed". I have spoken with these people for almost every night for a month and a half, when I get a hint that they have no idea what they're talking about, I just hang up and call another one up or just request a supervisor to speak with.
Here is my trace route result, I have highlight the part that are unacceptable.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
1    <1 ms    <1 ms    <1 ms Wireless_Broadband_Router.home [192.168.1.1]
2    61 ms    54 ms    23 ms L100.WASHDC-VFTTP-62.verizon-gni.net [96.231.212.1]
3    25 ms    15 ms    19 ms G11-3-662.WASHDC-LCR-06.verizon-gni.net [130.81.104.182]
4    36 ms    17 ms    33 ms so-4-2-0-0.RES-BB-RTR2.verizon-gni.net [130.81.28.146]
5    57 ms    65 ms    58 ms po1.ctn-border1.vzlink.com [206.46.225.85]
6    56 ms    67 ms    54 ms po121.ctn-core1.vzlink.com [206.46.225.18]
7    60 ms    71 ms    68 ms 206.46.228.130
8    76 ms   102 ms   141 ms 206.46.232.39
Trace complete
I'm going to list the things I have done so that perhaps if you are having the same issue, maybe you can anticipate or maybe save you time with this issue.
Replaced Router
This will be my 3rd Router in my possession. The odds of having 3 bad routers are astronomical but yet FSC will try to keep sending you more.
Replaced coax cable (twice), ONT, and splitter.
Once again, the problem still persist. To get these fix, I had total of 4 dispatchers. From the word of their mouth, they stated it's beyond their level and when it comes to latency the tech at verizon server will be the best people to help you.
Reset ONT by unplugging it for 5 minutes or more to pull up a new Gateway IP.
Appearently, someone were able to fix their latency issue this way but the results are mixed. Either it's a permanent fix or temporary fix or it made the problem even worse.
Optimizing connection/wired connections
I have a gaming PC, when they ask to clear the cache to solve my problem, it's an insult. Not only it's irralavent, in order for the computer to bog down because of cache overload, I must possess a computer that is less than of Pentium 2 back from 1995.
Anti-virus and FireWall
If these were actually the source of my problem then the high latency should be constantly bad.
Potentially hacked or other connection to your router.
While this problem can be an issue, I can see who uses the internet and even turned off the wireless. There's no way an uninvited person can slow down my connections.
The server that I am connecting to such as website and gaming server is not guaranteed by the verizon.
Yes, that is true but what are the odds of having google, verizon.net, altavista, gaming server from Steam, etc are having the latency issue all at the same time? It is as if they are blaming traffic problem on I-95 for having bad congestion on I-66. It's not relevant at all!
Verizon in-home Agent
Must I continue?
I will now list the solutions that others have found. Please keep in mind that these problems may not be relevant to you.
1) Bad PON card
Good luck convincing the verizon that this is the issue. For this to be the issue, people from your neighborhood must experience the same problem. Sadly, the problem is the latency and most people will be completely unaware of the problem as long as they are "online". There were cases where group of people resolved the problem but unfortunately the problem came back again the next day because the network tech at Verizon decided to switch them back to the old one.
2) Faulty hardware on rack
As far as I have been told, couple claimed that this has been the issue and was permitted to move their line into another rack.
3) Switching Gateway IP
One have claimed that certain Gateway IP they have been assigned are bad. For example, the house you're trying to drive away from has a huge pothole so you have to go around it by taking a detour.
4) Resetting the ONT by unplugging the battery
There has been claim that doing this for 5 mintues clears it up. What this actually does is it allows you to get a new Gateway IP and re-establish connections.
5) They blocked my IP
Yes, this can happen. I have been blocked once or more perhaps because sometimes I like to purchase and download games from Steam. When I do download, it does so for about an hour to 3 hours depending on the size of the game. Whilst this is going on, my room mate watches movie on Netflex and perhaps download music on the side. Also I watch On-Demand (requires internet). Also not to mention sometimes torrent and other P2P downloads. Check to see if you are blocked.
6) Last but not least, Verizon is purposely gimping our latency to squeeze budget.
There has been talks and speculations that since many primary account holders are not advance users. In otherwords, many would settle for just being "online". This supports the claims for having such a low standard for latency management in verizon. If so, Verizon must stop advertising their "fast" gaming gimmick that they display on their commercial.

What do I have to do to get better latency

I'm using a Presonus Firebox with LS9.1.1 on an iMac Intel Core Duo @ 5.66GHz.
The lowest that I can get my I/O Buffer Size is 64 Samples.
24 bit recording.
Small Process Buffer Range.
Software Monitoring is on.
Latency compensation is on.
I could work at 64 samples but the latency when playing guitar and using software monitoring is a drag.
If I go down to 32 samples it gets all noisy and is unusable.
What do I have to do to get less latency on my system?
When I bought this iMac I thought it would be able to do the job.

If the only reason why you want to use software monitoring is because you want to be able to use plug in effect and hear them live, then there's a better way to do this. You use the built in latency-free monitoring offered by you audio interface. Then, in Logic, you keep software monitoring on, but you mute the input channel in Logic (so you don't hear the direct input signal, which will have a weird, slapback delay because it will be a fraction later than your interface's built-in monitoring). Then, using sends and busses (not inserts), you can send you guitar (or vocals or whatever) to as many plug in effects as you like. This way you could even work with a buffer setting of 128 or 256 which will put far less strain on your computer. The only thing is that the fx return will have a slight predelay to it, but this isn't necessarily undesirable, in fact it's a valid sound that is often intentionally created in a mix. In any case, it doesn't matter as it's only monitoring fx, to give you a nice sound to vibe with as you play, and it can be far more inspiring to be able to record with nice rich effects in monitoring (even if they are slightly pre-delayed), than having to put up with very distracting latency in your cans just because your computer can't give you the low buffer setting you want to use.
Seriously, make use of the zero latency function of your audio hardware and just use software monitoring to give yourself a bit of an effects return to help put yourself in the mood for recording.. it's a good compromise.

WRT54GS v4 developed increasing lag, now it can't get an IP from the modem at all.

I am connected wirelessly to my WRT54GS v4 over WPA2, and it's worked very well for years. About 2 days ago, the router started developing serious lag. Some web pages (CNN, Google, etc) would time out only to work OK 10 seconds later (or not.) A traceroute to the offending domain would show my second hop as timing out, with all other hops < 80ms. Sometimes I'd get 3 webpages (all on different sites) hanging at the same time, only to finally display 20 seconds later simultaneously.
That was all on firmware 1.06.1. I just upgraded successfully to 1.06.3, with absolutely no change. I held reset for more than 30 seconds with no change.
The router looks like it can't get an IP from the modem at all. Clicking the DHCP Renew button in the web interface just bounces back to the same page but doesn't show that it's picked up a valid IP address.
If I plug into my cable modem directly from my laptop, the connection is awesomely fast with zero hangs or hesitation.
Can *anyone* help me please?

I was able to fix my problem by following alllll the instructions on this page: http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=4572&p_created=11658...
I also remembered that I had been resetting my cable modem (by power-cycling it) once or twice a day because it was losing its signal. I wonder if that was part of the problem?

Getting your photos from your computer back onto your camera

I downloaded pictures from my camera to my computer and when i unplugged my camera all the pictures were deleted from my camera's memory card. I want to know how to get the pictures from my computer back onto my camera. Please Help!!!
thanks,
Alexa A.

Alexa:
Welcome to the Apple Discussions. Unless the camera can be mounted on the desktop like an external storage device you'll have to get a card reader, mount the memory card with it and copy the photos back to the card. I'd take one photo with the camera first so there will be the correct folder configuration on the card to put the photos.
IMO it's much safer to upload the photos to a folder on the desktop with Image Capture or a card reader and then import from there into iPhoto. Too many reports of incomplete or aborted uploads and complete deletions from the camera.
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto (iPhoto.Library for iPhoto 5 and earlier) database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've created an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 6 and 7 libraries and Tiger and Leopard. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

HT204291 Why can't I get full screen from my ipad to Apple TV

Why can't I get full screen from my ipad to Apple TV?

Welcome to the Apple Community.
Mirroring won't fill the TV screen. The iPad has an aspect ratio of 4:3 and the iPhone 4S or prior an aspect ratio of 3:2, neither of these will fit exactly into a TV screen which as an aspect ratio of 16:9. The Apple TV will not zoom the mirrored image, because it may well cut off information which is situated at the top or bottom of the screen.
You may wish to try each of the settings in settings > AirPlay > Adjust for Overscan for the best setting that suits you.

Serious latency when running Amplitube

Do others encounter this issue as well?
When I use Amplitube as a plugin, my guitar signal is processed with some serious latency. The interesting thing is that when I remove the plug in and use any of Logic's own templates the latency remains. This happens an all buffer settings - from the lowest to the highest. The only way to sort this is to go into Preferences and reset the audio interface. But then I still hear latency with Amplitube.
I am working on an iMac with OS Mavericks
My interface is an Apogee Jam (non 96k).

I finally got it working by following the instructions on https://wiki.archlinux.org/index.php/Wicd.
I'm not sure which component solved the problem, but it is one of those:
* installing hal
* add user to group "network"
* remove interfaces from rc.conf (!eth0 ...)
* remove "network" from DAEMONS

Unable to get the values from ISearchResultList

Hi,
I am working on KM Indexmanagemnt API for searching with TREX, to build a search similar to msn or google.
I am following the example of Thilo Brandt, and after building the query, I am unable to retrieve the result from ISearchResultList, the results size its displaying is zero. But session.getTotalNumberResultKeys() is retrieving a value 20.
Here is the code I am using, please tell me where I am doing wrong.
public class SearchComponetOne extends AbstractPortalComponent {
     public void doContent(IPortalComponentRequest request,     IPortalComponentResponse response) {
com.sap.security.api.IUser nwUser =
               UMFactory.getAuthenticator().getLoggedInUser();
com.sapportals.portal.security.usermanagement.IUser user = null;
try {
      user = WPUMFactory.getUserFactory().getEP5User(nwUser);
     } catch (UserManagementException e) {
               response.write(e.getMessage());
   response.write("<html><head><title>Search</title></head><body>");
ResourceContext c = new ResourceContext(user);
try {
    IIndexService indexService = (IIndexService) ResourceFactory
                         .getInstance()
                         .getServiceFactory()
                         .getService(
                         IServiceTypesConst.INDEX_SERVICE);
   SearchQueryListBuilder sqb = new SearchQueryListBuilder();
   sqb.setSearchTerm("sap");
IQueryEntryList qel = sqb.buildSearchQueryList();
// get an instance of federated search
IFederatedSearch federatedSearch =
               (IFederatedSearch) indexService.getObjectInstance(
          IWcmIndexConst.FEDERATED_SEARCH_INSTANCE);
     List indexList = new ArrayList();
     String index = null;
     if (index != null && index.length() > 0) {
          // take a specified index from index= parameter
          indexList.add(indexService.getIndex(index));
     } else {
          // take all available indexes
          indexList = indexService.getActiveIndexes();
     // it is recommended to use a search session object
     // for searching execution
     ISearchSession session = null;
     if (session == null)
     session = federatedSearch.searchWithSession(qel, indexList, c);
response.write("Inside doContent session.getNumberResultKeys() => " + session.getNumberResultKeys()); // output as 20
     this.renderResultHeader(response, session, indexList);
     // get all results from the search session
ISearchResultList results =     session.getSearchResults(1, session.getTotalNumberResultKeys());
response.write(" from session => " + results.size() + " and size is : " + results.toString()); // I am getting the results.size() as zero
Thanks

I think the problem is UME related. I had the same problem once. Try using a system user for searching, instead of the logged on user.
Like this:
com.sapportals.portal.security.usermanagement.IUser user = WPUMFactory.getUserFactory().getUser("cmadmin_service");
Please reward the points if this helps.

How to get the values from popup window to mainwindow

HI all,
   I want to get the details from popup window.
      i have three input fields and one search button in my main window. when i click search button it should display popup window.whenever i click on selected row of the popup window table ,values should be visible in my main window input fields.(normal tables)
   now i am able to display popup window with values.How to get the values from popup window now.
   I can anybody explain me clearly.
Thanks&Regards
kranthi

Hi Kranthi,
Every webdynpro component has a global controller called the component controller which is visible to all other controllers within the component.So whenever you want to share some data in between 2 different views you can just make it a point to use the component controller's context for the same. For your requirement (within your popups view context) you will have have to copy the component controllers context to your view. You then will have to (programmatically) fill this context with your desired data in this popup view. You can then be able to read this context from whichever view you want. I hope that this would have made it clear for you. Am also giving you an [example|http://****************/Tutorials/WebDynproABAP/Modalbox/page1.htm] which you can go through which would give you a perfect understanding of all this. In this example the user has an input field in the main view. The user enters a customer number & presses on a pushbutton. The corresponding sales orders are then displayed in a popup window for the user. The user can then select any sales order & press on a button in the popup. These values would then get copied to the table in the main view.
Regards,
Uday

How to get the values from a html form embedded in a swing container

Hi all,
I am developing an application in which i have to read a html file and display it in a swing container.That task i made it with the help of a tool.But now i want to get the values from that page.ie when the submit button is clicked all the values of that form should be retrived by a servlet/standalone application.I don't know how to proceed further.Any help in this regard will be very greatful
Thanks in advance,
Prakash

By parsing the HTML.

How to get multiple values from the list

I've a list of an item which I queried it from the database. I also created a button that will takes a selected items from the list when it was clicked. I used javabean to get the data from database.
<%     // clicked on Select District Button
Vector vselectedDistrict = new Vector();
Vector vdistrictID = new Vector();
String tmpSelectDistrict = "";
tmpSelectDistrict = request.getParameter("bSelectDistrict");
if(tmpSelectDistrict != null)
     // get multiple values from the list
     String[] selectedDistrict = request.getParameterValues("usrTDistrict");
     vselectedDistrict.clear();
     vdistrictID.clear();
     if((selectedDistrict != null) && (selectedDistrict.length != 0))
                       for(int i=0;i<selectedDistrict.length;i++)
               vselectedDistrict.addElement(selectedDistrict);
          vdistrictID = dbaseInfo.getcurrentDistrictID(nstate,vselectedDistrict);
          for(int i=0;i<vdistrictID.size();i++)
               out.println("district = " + selectedDistrict[i]);                         out.println("district ID= " + vdistrictID.get(i).toString());
%>
// get vdistrict from the database here......
<select name="usrTDistrict" size="5" multiple>
<%     for(int i = 0; i< vdistrict.size(); i++)
%>
     <option value="<%=vdistrict.get(i).toString()%>"><%=vdistrict.get(i).toString()%></option>
<%
%>
</select>
<input type="submit" name="bSelectDistrict" value="Select District">
Lets say the item that i selected from the list is 'Xplace' and I clicked on the Select District button,
what I got is this error message:
org.apache.jasper.JasperException: Unable to convert string 'Xplace' to class java.util.Vector for attribute usrTDistrict: java.lang.IllegalArgumentException: Property Editor not registered with the PropertyEditorManager
So where is going wrong and what the message means?. Any help very much appreciated. Thanks

These are just guesses that might hopefully steer you in directions you haven't looked in yet.
I presume you used triangle brackets (< >) to avoid having the Jive Forum think it was the "italics" tag?
Are you certain this: dbaseInfo.getcurrentDistrictID(nstate,vselectedDistrict);
expects a Vector as its second parameter? And returns a Vector?
I don't believe you've shown how you use the javabean, or its code? Perhaps it should be rewritten to accept an array of strings instead of a Vector?

I am getting serious latency from my Zoom R16!

Similar Messages

Maybe you are looking for