I cannot access my history

I can never access the history of any sites I have been to previously. When I open the window that is supposed to show me my history, it's blank. The 'most visited' tab is always empty. How do I solve this?

Check that you still keep history.
To see all the History and Cookie settings, select:
* Firefox (Tools) > Options > Privacy > History: Firefox will: "Use custom settings for history"
This can also be caused by a problem with the file places.sqlite that stores the bookmarks and the history.
* http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox

Similar Messages

  • I downloaded the new 3.6.6 and now cannot access any history from beyond yesterday

    I have a Windows 7 laptop, 64bit. I have always accessed all history of places I have been on the web. After downloading the latest upgrade from Firefox. 3.6.6., I now am unable to access my History for anything beyond Yesterday.
    == This happened ==
    Every time Firefox opened
    == upgraded to Firefox 3.6.6.

    This is normally caused by a firewall blocking the new version of Firefox. For details see https://support.mozilla.com/kb/Cannot+connect+after+upgrading+Firefox

  • Cannot access purchase history from before 2011

    I recently got a PS Vita and wanted to get some Playstation Classics on it that I purchased in 2009. I have the games on my PS3 and I can't find the games in my purchase history, nor can I actually find the games on the PSN store. What can I do to access those games?

    I was having the exact same problem, so here is how I got back to my History. Bear with me it is a bunch of steps, but mainly working through the apple's "Help" section till it takes you directly to the history page ... So - follow this link: http://www.apple.com/support/itunes/ (or if you are worried about a virus, then go to Apple's site then click support then click itunes). In the drop down section under "Customer Service" click on the "Itunes store and Account Billing" tab and it will give you a list I clicked on "Billing Inquiries" and got some info off to the right on my screen. I then click the blue sentence that says, "Finding your iTunes Store purchase history ... " and a popup box appeared. In the middle of the popup box were the words, "Purchase History" in blue. When I clicked that I was taken to my purchase history in my itunes program (FYI - a box did pop up asking me to let Int Expl open my itunes). I hope that helps - it took a while for me to find it, but it makes Christmas all the better to have something to actually print out and give.
    Merry Christmas
    Message was edited by: BFAStemples

  • I cannot access the internet, I tried to answer that said to go to settings, safari, tap clear history, cookies and cache, cut off, then on, but it did not work.  When I go to internet the screen is grey??? please help I am a new user!!

    I cannot access the internet the screen is grey, I have tried by using the answer from someone but it does not work...I went to settings, tap safari, then clear the history, cookies, and cache, then turn off ipad.  When I did that twice, it did not work.  How long does it take for the clear history to work?  I am a brand new
    user of the ipad2 and I am disappointed that this is happening already.

    Have you been able to access the internet previously and now it's suddenly not working, or are you still trying to access the internet for the first time on your iPad?  Are you at home trying to connect through your home router?  If you are at home, did you put your home routers encryption code as your password?  The encryption code is what your iPad is looking for and it is usually found on the router and is typically a 13 digit combination of letters and numbers.  Let us know......

  • Help! I cannot get to a website I was on 3 days ago, and the history button does not seem to take me to my browsing history. SO far I have gone back to Internet Explorere as the FF4 is too frustrating, but accessing my history is critical for contacts.

    In FF4 I cannot find where to access the history. I go to the red drop down box in the top of the left hand corner and there is a link to a history drop down, but then there will be nothing displayed- not for the day, or the week, or---. Where has the access to this information been moved? I am using Windows 7 .

    CTRL+H should give you your history unless you enabled "Clear Browsing History" in Options | Options | Privacy.
    Have a look at this add-on too: https://addons.mozilla.org/en-US/firefox/addon/undo-closed-tabs-button/

  • ASA 5505 Static hosts cannot access outside

    I'm replacing an old PIX with a second hand ASA firewall.
    I have configured the ASA in a very similar manner to how the PIX was set up but I'm having trouble with some hosts on the inside accessing the Internet. Any inside hosts which use DHCP work fine. Any inside hosts with a static IP (and configured on the ASA with a "static" rule) cannot access the Internet. For example, in the config below the server daviker-dialler cannot access the Internet.
    I've spent a few days working on this now and have started from scratch several times but I'm not getting anywhere.
    Apologies for all the X's everywhere, didn't like to post anything sensitive on the Internet. If I've obscured something pertinent let me know.
    Any advice would be greatly appreciated! Thanks.
    : Saved
    ASA Version 7.2(3)
    hostname fw-1
    domain-name XXXX
    enable password XXXX encrypted
    names
    name 92.X.X.61 bb-office
    name 92.X.X.128 gl-office
    name 10.0.0.117 daviker-dialler_in
    name 77.X.X.117 daviker-dialler_out
    name 10.0.0.112 data-2_in
    name 77.X.X.112 data-2_out
    name 10.0.0.81 corp-1_in
    name 77.X.X.81 corp-1_out
    name 10.0.0.111 data-1_in
    name 77.X.X.210 user_75
    interface Vlan1
    nameif inside
    security-level 100
    ip address 10.0.0.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 77.X.X.66 255.255.255.192
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    passwd XXXX encrypted
    ftp mode passive
    dns server-group DefaultDNS
    domain-name XXXX
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 5900
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 4040
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 9876
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq sip
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq www
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq https
    access-list inbound extended permit udp host bb-office host daviker-dialler_out eq sip
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 1433
    access-list inbound extended permit udp host bb-office host daviker-dialler_out eq netbios-ns
    access-list inbound extended permit udp host bb-office host daviker-dialler_out eq netbios-dgm
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq netbios-ssn
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 445
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 4040
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 9876
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq sip
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq www
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq https
    access-list inbound extended permit udp host gl-office host daviker-dialler_out eq sip
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 1433
    access-list inbound extended permit udp host gl-office host daviker-dialler_out eq netbios-ns
    access-list inbound extended permit udp host gl-office host daviker-dialler_out eq netbios-dgm
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq netbios-ssn
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 445
    access-list inbound extended permit tcp host gl-office host daviker-dialler_out eq 5900
    access-list inbound extended permit tcp any host data-2_out eq ssh
    access-list inbound extended permit tcp any host corp-1_out eq ssh
    access-list inbound extended permit tcp any host corp-1_out eq www
    access-list inbound extended permit tcp any host corp-1_out eq pop3
    access-list inbound extended permit tcp any host corp-1_out eq imap4
    access-list inbound extended permit tcp any host corp-1_out eq smtp
    access-list inbound extended permit tcp any host corp-1_out eq 995
    access-list inbound extended permit tcp any host corp-1_out eq 465
    access-list inbound extended permit tcp any host corp-1_out eq 993
    access-list inbound extended permit tcp any host corp-1_out eq 8008
    access-list inbound extended permit udp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq netbios-ns
    access-list inbound extended permit udp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq netbios-dgm
    access-list inbound extended permit tcp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq netbios-ssn
    access-list inbound extended permit tcp 77.X.X.64 255.255.255.192 host 77.X.X.113 eq 445
    access-list inbound extended permit udp any host 77.X.X.113 eq netbios-ns
    access-list inbound extended permit udp any host 77.X.X.113 eq netbios-dgm
    access-list inbound extended permit tcp any host 77.X.X.113 eq netbios-ssn
    access-list inbound extended permit tcp any host 77.X.X.113 eq 445
    access-list inbound extended permit tcp host bb-office host data-2_out eq 5901
    access-list inbound extended permit tcp host bb-office host data-2_out eq 3690
    access-list inbound extended permit tcp host bb-office host data-2_out eq www
    access-list inbound extended permit tcp host bb-office host daviker-dialler_out eq 3389
    access-list inbound extended permit tcp host 2.X.X.18 host data-2_out eq 3306
    access-list inbound extended permit tcp any host data-2_out eq 3306
    access-list inbound extended permit tcp host 212.X.X.7 host daviker-dialler_out eq 5900
    access-list inbound extended permit tcp host bb-office host data-2_out eq 3306
    access-list inbound extended permit tcp host user_75 host daviker-dialler_out eq 1433
    access-list inbound extended permit tcp host user_75 host daviker-dialler_out eq 5900
    access-list inbound extended permit tcp host user_75 host data-2_out eq 3690
    access-list inbound extended permit tcp host user_75 host data-2_out eq www
    access-list inbound extended permit tcp host user_75 host data-2_out eq 3306
    pager lines 24
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-523.bin
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 1 0.0.0.0 0.0.0.0
    static (inside,outside) daviker-dialler_out daviker-dialler_in netmask 255.255.255.255
    static (inside,outside) corp-1_out corp-1_in netmask 255.255.255.255
    static (inside,outside) data-2_out data-2_in netmask 255.255.255.255
    static (inside,outside) 77.X.X.113 data-1_in netmask 255.255.255.255
    access-group inbound in interface outside
    route outside 0.0.0.0 0.0.0.0 77.X.X.65 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout uauth 0:05:00 absolute
    aaa authentication ssh console LOCAL
    aaa authentication telnet console LOCAL
    aaa authorization command LOCAL
    http server enable
    http 10.0.0.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    telnet 0.0.0.0 0.0.0.0 inside
    telnet timeout 5
    ssh 0.0.0.0 0.0.0.0 inside
    ssh timeout 5
    console timeout 0
    dhcpd dns 77.X.X.91 8.8.8.8
    dhcpd domain cagltd.net
    dhcpd auto_config outside
    dhcpd address 10.0.0.20-10.0.0.40 inside
    dhcpd enable inside
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
    service-policy global_policy global
    username matt password XXXX encrypted
    prompt hostname context
    Cryptochecksum:00af76f23831b8c828fc6677c9069072
    : end

    Hi Jouni,
    Thanks for the info.
    I didn't have icmp traffic allowed, so I knew ping wouldn't be working. I was testing using http.
    I have enabled icmp and dhcp clients can ping outside. Static nat clients can't ping outside. Static clients also cannot use outbound http.
    As suggested, I have run some packet traces.
    From a static nat client on the ASA:
    fw-1# packet-tracer input inside tcp 10.0.0.81 80 173.203.209.67 80
    Phase: 1
    Type: ACCESS-LIST
    Subtype:
    Result: ALLOW
    Config:
    Implicit Rule
    Additional Information:
    MAC Access list
    Phase: 2
    Type: FLOW-LOOKUP
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Found no matching flow, creating a new flow
    Phase: 3
    Type: ROUTE-LOOKUP
    Subtype: input
    Result: ALLOW
    Config:
    Additional Information:
    in   0.0.0.0         0.0.0.0         outside
    Phase: 4
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 5
    Type: NAT
    Subtype:
    Result: ALLOW
    Config:
    static (inside,outside) corp-1_out corp-1_in netmask 255.255.255.255
      match ip inside host corp-1_in outside any
        static translation to corp-1_out
        translate_hits = 668, untranslate_hits = 2
    Additional Information:
    Static translate corp-1_in/0 to corp-1_out/0 using netmask 255.255.255.255
    Phase: 6
    Type: NAT
    Subtype: host-limits
    Result: ALLOW
    Config:
    static (inside,outside) corp-1_out corp-1_in netmask 255.255.255.255
      match ip inside host corp-1_in outside any
        static translation to corp-1_out
        translate_hits = 668, untranslate_hits = 2
    Additional Information:
    Phase: 7
    Type: HOST-LIMIT
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 8
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 9
    Type: FLOW-CREATION
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    New flow created with id 1759, packet dispatched to next module
    Phase: 10
    Type: ROUTE-LOOKUP
    Subtype: output and adjacency
    Result: ALLOW
    Config:
    Additional Information:
    found next-hop 77.X.X.65 using egress ifc outside
    adjacency Active
    next-hop mac address 0017.0f13.5000 hits 1
    Result:
    input-interface: inside
    input-status: up
    input-line-status: up
    output-interface: outside
    output-status: up
    output-line-status: up
    Action: allow
    This looks fine to me, but as I say, an outbound tcp port 80 connection from the actual machine on 10.0.0.81 fails.
    Here is a similar trace from a dhcp client to the same destination:
    fw-1# packet-tracer input inside tcp 10.0.0.20 80 173.203.209.67 80
    Phase: 1
    Type: FLOW-LOOKUP
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Found no matching flow, creating a new flow
    Phase: 2
    Type: ROUTE-LOOKUP
    Subtype: input
    Result: ALLOW
    Config:
    Additional Information:
    in   0.0.0.0         0.0.0.0         outside
    Phase: 3
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 4
    Type: NAT
    Subtype:
    Result: ALLOW
    Config:
    nat (inside) 1 0.0.0.0 0.0.0.0
      match ip inside any outside any
        dynamic translation to pool 1 (77.74.111.66 [Interface PAT])
        translate_hits = 990, untranslate_hits = 226
    Additional Information:
    Dynamic translate 10.0.0.20/80 to 77.74.111.66/1 using netmask 255.255.255.255
    Phase: 5
    Type: NAT
    Subtype: host-limits
    Result: ALLOW
    Config:
    nat (inside) 1 0.0.0.0 0.0.0.0
      match ip inside any inside any
        dynamic translation to pool 1 (No matching global)
        translate_hits = 0, untranslate_hits = 0
    Additional Information:
    Phase: 6
    Type: HOST-LIMIT
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 7
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 8
    Type: FLOW-CREATION
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    New flow created with id 1771, packet dispatched to next module
    Phase: 9
    Type: ROUTE-LOOKUP
    Subtype: output and adjacency
    Result: ALLOW
    Config:
    Additional Information:
    found next-hop 77.X.X.65 using egress ifc outside
    adjacency Active
    next-hop mac address 0017.0f13.5000 hits 5
    Result:
    input-interface: inside
    input-status: up
    input-line-status: up
    output-interface: outside
    output-status: up
    output-line-status: up
    Action: allow
    I can see the difference in the NAT translation section. A real outbound tcp port 80 connection from the actual machine on 10.0.0.20 works fine.
    Finally, for the sake of comparison, I ran a similar packet trace using a static nat IP on the old PIX firewall:
    old-fw-1# packet-tracer input inside tcp 10.0.0.117 80 173.203.209.67 80
    Phase: 1
    Type: ACCESS-LIST
    Subtype:
    Result: ALLOW
    Config:
    Implicit Rule
    Additional Information:
    MAC Access list
    Phase: 2
    Type: FLOW-LOOKUP
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Found no matching flow, creating a new flow
    Phase: 3
    Type: ROUTE-LOOKUP
    Subtype: input
    Result: ALLOW
    Config:
    Additional Information:
    in   0.0.0.0         0.0.0.0         outside
    Phase: 4
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 5
    Type: INSPECT
    Subtype: np-inspect
    Result: ALLOW
    Config:
    class-map inspection_default
    match default-inspection-traffic
    policy-map global_policy
    class inspection_default
      inspect http
    service-policy global_policy global
    Additional Information:
    Phase: 6
    Type: NAT
    Subtype:
    Result: ALLOW
    Config:
    static (inside,outside) daviker-dialler_out daviker-dialler_in netmask 255.255.255.255
    nat-control
      match ip inside host daviker-dialler_in outside any
        static translation to daviker-dialler_out
        translate_hits = 17132, untranslate_hits = 1277850
    Additional Information:
    Static translate daviker-dialler_in/0 to daviker-dialler_out/0 using netmask 255.255.255.255
    Phase: 7
    Type: NAT
    Subtype: host-limits
    Result: ALLOW
    Config:
    static (inside,outside) daviker-dialler_out daviker-dialler_in netmask 255.255.255.255
    nat-control
      match ip inside host daviker-dialler_in outside any
        static translation to daviker-dialler_out
        translate_hits = 17132, untranslate_hits = 1277850
    Additional Information:
    Phase: 8
    Type: IP-OPTIONS
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    Phase: 9
    Type: FLOW-CREATION
    Subtype:
    Result: ALLOW
    Config:
    Additional Information:
    New flow created with id 1006075, packet dispatched to next module
    Phase: 10
    Type: ROUTE-LOOKUP
    Subtype: output and adjacency
    Result: ALLOW
    Config:
    Additional Information:
    found next-hop 78.X.X.69 using egress ifc outside
    adjacency Active
    next-hop mac address 0017.0f13.5000 hits 572133
    Result:
    input-interface: inside
    input-status: up
    input-line-status: up
    output-interface: outside
    output-status: up
    output-line-status: up
    Action: allow
    Outbound traffic from static nat hosts on the old PIX firewall works fine. One glaring difference is that the PIX is inspecting http traffic, but surely this is a red herring. Another difference is that the old and new firewalls have different gateways / default routes & different outside IP addresses. As the new ASA firewall (and its dhcp hosts) can talk to the outside world quite happily I don't think this is relevant.
    I wondered whether it might be down to the difference in the inside (255.255.255.0) and outside (255.255.255.192) subnets. The set up is the same on the PIX, but I wondered whether some other line of config might be required on the ASA to handle it. I adjusted the subnet of the inside interface on the ASA to match the outside one (both 255.255.255.192) but it didn't make any difference.
    So I'm puzzled!

  • Cisco ASA 5505 L2TP VPN cannot access internal network

    Hi,
    I'm trying to configure Cisco L2TP VPN to my office. After successful connection I cannot access to internal network.
    Can you jhelp me to find out the issue?
    I have Cisco ASA:
    inside network - 192.168.1.0
    VPN network - 192.168.168.0
    I have router 192.168.1.2 and I cannot ping or get access to this router.
    Here is my config:
    ASA Version 8.4(3)
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    interface Ethernet0/4
    interface Ethernet0/5
    interface Ethernet0/6
    interface Ethernet0/7
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.1 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 198.X.X.A 255.255.255.248
    ftp mode passive
    same-security-traffic permit intra-interface
    object network net-all
    subnet 0.0.0.0 0.0.0.0
    object network vpn_local
    subnet 192.168.168.0 255.255.255.0
    object network inside_nw
    subnet 192.168.1.0 255.255.255.0
    access-list outside_access_in extended permit icmp any any echo-reply
    access-list outside_access_in extended deny ip any any log
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    ip local pool sales_addresses 192.168.168.1-192.168.168.254
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    nat (inside,outside) source dynamic net-all interface
    nat (inside,outside) source static inside_nw inside_nw destination static vpn_local vpn_local
    nat (outside,inside) source static vpn_local vpn_local destination static inside_nw inside_nw route-lookup
    object network vpn_local
    nat (outside,outside) dynamic interface
    object network inside_nw
    nat (inside,outside) dynamic interface
    access-group outside_access_in in interface outside
    route outside 0.0.0.0 0.0.0.0 198.X.X.B 1
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication enable console LOCAL
    aaa authentication ssh console LOCAL
    aaa authentication http console LOCAL
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec ikev1 transform-set my-transform-set-ikev1 esp-3des esp-sha-hmac
    crypto ipsec ikev1 transform-set my-transform-set-ikev1 mode transport
    crypto dynamic-map dyno 10 set ikev1 transform-set my-transform-set-ikev1
    crypto map vpn 20 ipsec-isakmp dynamic dyno
    crypto map vpn interface outside
    crypto isakmp nat-traversal 3600
    crypto ikev1 enable outside
    crypto ikev1 policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh 192.168.1.0 255.255.255.0 inside
    ssh timeout 30
    console timeout 0
    management-access inside
    dhcpd address 192.168.1.5-192.168.1.132 inside
    dhcpd dns 75.75.75.75 76.76.76.76 interface inside
    dhcpd enable inside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy sales_policy internal
    group-policy sales_policy attributes
    dns-server value 75.75.75.75 76.76.76.76
    vpn-tunnel-protocol l2tp-ipsec
    username ----------
    username ----------
    tunnel-group DefaultRAGroup general-attributes
    address-pool sales_addresses
    default-group-policy sales_policy
    tunnel-group DefaultRAGroup ipsec-attributes
    ikev1 pre-shared-key *****
    tunnel-group DefaultRAGroup ppp-attributes
    authentication ms-chap-v2
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous
    Cryptochecksum:5d1fc9409c87ecdc1e06f06980de6c13
    : end
    Thanks for your help.

    You have to test it with "real" traffic to 192.168.1.2 and if you use ping, you have to add icmp-inspection:
    policy-map global_policy
      class inspection_default
        inspect icmp
    Don't stop after you've improved your network! Improve the world by lending money to the working poor:
    http://www.kiva.org/invitedby/karsteni

  • Cannot access internal LAN after VPN connect

    I know this is either an ACL or NAT issue that I cannot figure out.  The nat-t config in defaulted in the IOS config for the ASA.  I actually forgot the command to show the hidden default config lines.  Either way, can someone take a look at my config, and let me know what I am doing wrong, again.
    Thanks ahead of time.
    ASA Version 8.2(2)
    hostname ciscousa
    enable password
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 1.1.1.2 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address 14.14.11.5 255.255.255.0
    interface Vlan3
    shutdown
    no forward interface Vlan2
    nameif dmz
    security-level 50
    ip address dhcp
    interface Ethernet0/0
    switchport access vlan 2
    speed 100
    duplex full
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    speed 100
    duplex full
    ftp mode passive
    same-security-traffic permit intra-interface
    access-list outside_in extended permit icmp any any
    access-list inside_nat0 extended permit ip any 1.1.1.0 255.255.255.0
    access-list inside_nat0 extended permit ip any 10.12.27.0 255.255.255.0
    access-list split_tunnel standard permit 1.1.1.0 255.255.255.0
    pager lines 24
    logging enable
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    mtu dmz 1500
    ip local pool vpnpool 10.12.27.100-10.12.27.120 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0
    nat (inside) 1 0.0.0.0 0.0.0.0
    access-group outside_in in interface outside
    route outside 0.0.0.0 0.0.0.0 14.14.11.6 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 1.1.1.0 255.255.255.0 inside
    http 1.1.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map inet-1_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto map inet-1_map 65535 ipsec-isakmp dynamic inet-1_dyn_map
    crypto map inet-1_map interface outside
    crypto isakmp identity address
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy vpnipsec internal
    group-policy vpnipsec attributes
    wins-server value 1.1.1.16
    dns-server value 1.1.1.16
    split-tunnel-policy tunnelspecified
    split-tunnel-network-list value split_tunnel
    default-domain value company.com
    tunnel-group vpnipsec type remote-access
    tunnel-group vpnipsec general-attributes
    address-pool vpnpool
    default-group-policy vpnipsec
    tunnel-group vpnipsec ipsec-attributes
    pre-shared-key *****
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512

    Hello,
    I have been trying to get this to work within the last week but to no avail.  I changed my config altogether and started from scratch.  I have Split Tunnel working well, and I can access the VPN client from the internal LAN.  But I still cannot access the internal LAN from the VPN client host.    Can anyone take a look at my config and tell me what ACL\Access Group I am missing.  I know I am close but I cannot get over the hump.
    Thanks!
    ASA Version 8.2(2)
    names
    interface Vlan1
    nameif inside
    security-level 100
    ip address 192.168.1.2 255.255.255.0
    interface Vlan2
    nameif outside
    security-level 0
    ip address xxx.xxx.xxx.xxx 255.255.255.0
    interface Vlan3
    shutdown
    no forward interface Vlan2
    nameif dmz
    security-level 50
    ip address dhcp
    interface Ethernet0/0
    switchport access vlan 2
    interface Ethernet0/1
    interface Ethernet0/2
    interface Ethernet0/3
    speed 100
    duplex full
    interface Ethernet0/4
    interface Ethernet0/5
    switchport access vlan 3
    interface Ethernet0/6
    interface Ethernet0/7
    ftp mode passive
    same-security-traffic permit inter-interface
    same-security-traffic permit intra-interface
    access-list outside_in extended permit icmp any any
    access-list outside_in_vpn extended permit ip 192.168.3.0 255.255.255.0 any
    access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
    access-list split_tunnel standard permit 192.168.0.0 255.255.0.0
    access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
    access-list inside_access_in extended permit ip any any
    access-list outside_access_in extended permit ip any any
    pager lines 24
    logging enable
    logging buffered debugging
    logging asdm informational
    mtu inside 1500
    mtu outside 1500
    mtu dmz 1500
    ip local pool ipvpn 192.168.3.100-192.168.3.200 mask 255.255.255.0
    icmp unreachable rate-limit 1 burst-size 1
    no asdm history enable
    arp timeout 14400
    global (outside) 1 interface
    nat (inside) 0 access-list inside_nat0_outbound
    nat (inside) 1 0.0.0.0 0.0.0.0
    access-group inside_access_in in interface inside
    access-group outside_in in interface outside control-plane
    access-group outside_in_vpn in interface outside
    route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xx 1
    timeout xlate 3:00:00
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-record DfltAccessPolicy
    http server enable
    http 192.168.1.0 255.255.255.0 inside
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart
    crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
    crypto ipsec security-association lifetime seconds 28800
    crypto ipsec security-association lifetime kilobytes 4608000
    crypto dynamic-map internet-1_dyn_map 20 set transform-set ESP-3DES-SHA
    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHAESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
    crypto map internet-1_map 65535 ipsec-isakmp dynamic internet-1_dyn_map
    crypto map internet-1_map interface outside
    crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
    crypto map inside_map interface inside
    crypto isakmp identity address
    crypto isakmp enable inside
    crypto isakmp enable outside
    crypto isakmp policy 10
    authentication pre-share
    encryption 3des
    hash sha
    group 2
    lifetime 86400
    telnet timeout 5
    ssh timeout 5
    console timeout 0
    management-access inside
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    webvpn
    group-policy DfltGrpPolicy attributes
    group-policy vpnipsec internal
    group-policy vpnipsec attributes
    wins-server value 192.168.1.5
    dns-server value 192.168.1.5
    split-tunnel-policy tunnelall
    split-tunnel-network-list value split_tunnel
    default-domain value company.com
    tunnel-group vpnipsec type remote-access
    tunnel-group vpnipsec general-attributes
    address-pool ipvpn
    default-group-policy vpnipsec
    tunnel-group vpnipsec ipsec-attributes
    pre-shared-key *
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    prompt hostname context
    Cryptochecksum:7e41045c9d7c66ac2c03c3b12ae63908

  • I upgraded to iOS x mavericks on my iMac now i cannot access my iPhoto i get this messageThis update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled.

    I upgraded to iOS x mavericks on my iMac now i cannot access my iPhoto i get this messageThis update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled. I have not changed anything thankyou for any info.

    Please test after each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes. Keep in mind that no one here represents Apple or can help with customer-service issues.
    Step 1
    A purchased app can only be updated by signing in to the App Store with the same Apple ID that was originally used to buy it. There's no way around that limitation, which also applies to free apps. If you can't sign in with the buyer's ID, delete the app and reinstall it. You'll have to pay for it again, if applicable.
    Step 2
    If you get the alert when trying to update a bundled iLife app, elect the Purchases page in the App Store and locate the app in your purchase history. If there's a button marked ACCEPT on the right, click it.
    If you have a used Mac, the bundled apps were linked to the original owner's Apple ID and can't be transferred to you. Reportedly, customer service has issued redemption codes to some second owners who asked, but it's not guaranteed.
    Step 3
    If you're trying to update iLife or iWork apps that were installed from a purchased DVD, or if you have a refurbished Mac bought directly from Apple, contact App Store customer service for a redemption code. You may be asked for the part number of the DVD.
    Step 4
    From the App Store menu bar, select
    Store ▹ View My Account
    Enter your Apple ID password at the prompt. At the lower right corner of the window that opens, click the Reset button. Close the window.
    See also: remove app
    Keywords: refunded canceled

  • Cannot access help file from iPhoto

    IPhotos cannot access iPhoto's tutorial from the apps help window.   Apple diagnostics indicates my network is functional and passes diagnostics.   iPhoto cannot access my wifi network.  The message also says to check back later.
    Howie

    There are 9 different versions of iPhoto and they run on 10 different versions of the Operating System. The tricks and tips for dealing with issues vary depending on the version of iPhoto and the version of the OS. So to get help you need to give as much information as you can. Include things like:
    - What version of iPhoto.
    - What version of the Operating System.
    - Details. As full a description of the problem as you can. For example, if you have a problem with exporting, then explain by describing how you are trying to export, and so on.
    - History: Is this going on long? Has anything been installed or deleted? - Are there error messages?
    - What steps have you tried already to solve the issue.
    - Anything unusual about your set up? Or how you use iPhoto?
    Anything else you can think of that might help someone understand the problem you have.

  • [resolved] Cannot access particular site

    I cannot access http://www.philosophypages.com. I tested using the "is it down or is it me?" site and apparently, it is "just me". I can ping the site fine. But if I try to view the page in firefox, it hangs forever. I don't see any complaints in the error/warning/info console, though. If I try to access it with lynx, eventually it just times out and says it could not make the connection.
    I've accessed the same site just fine before. I can access other sites just fine now.
    Can anybody suggest ways to track the issue down?
    $ traceroute www.philosophypages.com
    traceroute to www.philosophypages.com (207.155.252.12), 30 hops max, 60 byte packets
    1 xx.x.x.x (x.x.x.x) 3.122 ms 7.112 ms 7.123 ms
    2 xx.xxx.xxx.x (xx.xxx.xxx.x) 13.841 ms 13.950 ms 21.623 ms
    3 xxxx-xxxx-xx-xxx-xxx.network.virginmedia.net (xx.xxx.xxx.xxx) 21.651 ms 21.716 ms 21.794 ms
    4 xxxx-xx-xx-xxx-x.network.virginmedia.net (xx.xxx.xxx.xxx) 27.572 ms 27.639 ms 27.630 ms
    5 xe-7-0-0.edge3.London2.Level3.net (195.50.91.129) 31.243 ms 31.287 ms 35.437 ms
    6 ae-0-11.edge4.London2.Level3.net (4.69.200.126) 36.044 ms 22.750 ms 21.694 ms
    7 ae-3-3.ebr1.London1.Level3.net (4.69.141.189) 22.314 ms 30.534 ms 30.419 ms
    8 ae-57-112.csw1.London1.Level3.net (4.69.153.118) 30.589 ms ae-58-113.csw1.London1.Level3.net (4.69.153.122) 32.039 ms ae-59-114.csw1.London1.Level3.net (4.69.153.126) 31.964 ms
    9 ae-1-51.edge4.London1.Level3.net (4.69.139.74) 31.659 ms 31.744 ms 32.072 ms
    10 XO-level3-1x10G.London.Level3.net (4.68.70.134) 32.256 ms 32.341 ms 32.122 ms
    11 vb1042.rar3.nyc-ny.us.xo.net (207.88.13.202) 107.633 ms 111.691 ms 107.710 ms
    12 te-3-0-0.rar3.washington-dc.us.xo.net (207.88.12.74) 169.505 ms 167.730 ms 172.305 ms
    13 te-11-0-0.rar3.sanjose-ca.us.xo.net (207.88.12.69) 173.591 ms 173.456 ms 173.677 ms
    14 ae0d0.mcr1.fremont-ca.us.xo.net (216.156.0.138) 167.153 ms 165.860 ms 167.242 ms
    15 ae1d0.mcr2.fremont-ca.us.xo.net (216.156.1.70) 166.037 ms 171.930 ms 171.810 ms
    16 209.116.66.138 (209.116.66.138) 171.997 ms 164.010 ms 162.785 ms
    17 206.251.128.138.ptr.us.xo.net (206.251.128.138) 162.577 ms 170.301 ms 170.335 ms
    18 * * *
    19 * * *
    20 * * *
    21 * * *
    22 * * *
    23 * * *
    24 * * *
    25 * * *
    26 * * *
    27 * * *
    28 * * *
    29 * * *
    30 * * *
    Last edited by cfr (2013-02-23 22:57:57)

    Works okay here.
    1 ewaller (192.168.1.1) 0.848 ms 1.473 ms 1.435 ms
    2 netblock-<redacted>.dslextreme.com (<redacted>) 10.585 ms 11.753 ms 12.152 ms
    3 lax1_cr1_gig_10_0_120.dslextreme.com (66.218.48.145) 13.750 ms 14.603 ms 16.036 ms
    4 ge-6-5.car4.LosAngeles1.Level3.net (4.71.128.1) 18.441 ms 18.798 ms 19.272 ms
    5 xo-level3-xe.losangeles9.level3.net (4.53.228.10) 21.344 ms 23.157 ms 24.477 ms
    6 207.88.14.209.ptr.us.xo.net (207.88.14.209) 41.759 ms 35.728 ms 32.297 ms
    7 ae0d0.mcr1.fremont-ca.us.xo.net (216.156.0.138) 33.857 ms 22.385 ms 20.789 ms
    8 ae1d0.mcr2.fremont-ca.us.xo.net (216.156.1.70) 22.237 ms 23.305 ms 23.283 ms
    9 209.116.66.138 (209.116.66.138) 24.918 ms 25.905 ms 27.264 ms
    10 206.251.128.138.ptr.us.xo.net (206.251.128.138) 28.415 ms 29.845 ms 30.189 ms
    11 * * *
    12 * * *
    13 * * *
    14 * * *
    15 * * *
    16 * * *
    17 * * *
    18 * * *
    19 * * *
    20 * * *
    21 * * *
    22 * * *
    23 * * *
    24 * * *
    25 * * *
    26 * * *
    27 * * *
    28 * * *
    29 * * *
    30 * * *
    It must be all those xx's in your IP 
    From the site:
    Philosophy Pages
    . . . from Garth Kemerling
    This site offers helpful information for students of the Western philosophical tradition. The elements you will find on this site include:
    The Dictionary of Philosophical Terms and Names.
    A survey of the History of Western Philosophy.
    A Timeline for the intellectual figures discussed here.
    Detailed discussion of several major Philosophers
    Summary treatment of the elementary principles of Logic
    A generic Study Guide for students of philosophy.
    Links to other philosophy Sites on the Internet.
    Edit:  We both found our way to 206.251.128.138.ptr.us.xo.net   . 
    Last edited by ewaller (2013-01-25 04:42:27)

  • Since I disabled features in the people widget, I cannot access gmail

    I was so annoyed at the people widget covering up my emails that I disabled all the features IN it instead of the whole widget (which I have since learned how to do) and now I cannot access gmail with firefox. I can with internet explorer though, but prefer to use firefox.

    -> Tap '''ALT''' key or press '''F10''' to show the Menu Bar
    -> go to Help Menu -> select '''Restart with Add-ons Disabled'''
    Firefox will close then it will open up with just basic Firefox. Now do this:
    -> Update ALL your Firefox Plug-ins https://www.mozilla.com/en-US/plugincheck/
    -> go to View Menu -> Toolbars -> unselect All Unwanted/Incompatible Toolbars
    -> go to Tools Menu -> Clear Recent History -> '''Time range to clear: select "EVERYTHING"''' -> click Details (small arrow) button -> place Checkmarks on '''Cookies, Cache''' -> click '''Clear Now'''
    -> go to Tools Menu -> Options -> General -> in '''Startup''' section click '''Reset to Default''' button
    -> go to Tools Menu -> Options -> Content -> place Checkmarks on:
    1) Block Pop-up windows 2) Load images automatically 3) Enable JavaScript
    -> go to Tools Menu -> Options -> Security -> place Checkmarks on:
    1) Warn me when sites try to install add-ons 2) Block reported attack sites 3) Block reported web forgeries 4) Remember Passwords for sites
    -> go to Tools Menu -> Options -> Advanced -> Network -> Offline Storage (Cache): click '''Clear Now''' button
    -> Click OK on Options window
    -> click the Favicon on SearchBar -> click '''Manage Search Engines''' -> select all Unwanted Search Engines and click '''Remove''' -> click OK
    -> go to Tools Menu -> Add-ons -> Extensions section -> REMOVE All Unwanted/Suspicious/Incompatible Extensions (Add-ons) -> Restart Firefox
    -> go to Tools Menu -> Add-ons -> Appearance section -> REMOVE All Unwanted/Suspicious/Incompatible Themes (Persona) -> Restart Firefox
    You can enable your Known & Trustworthy Add-ons and Themes later. Check and tell if its working.

  • I cannot access my mail from my ipad. I keep getting an error message "MFMessageErrorDomain error 1032". Does anyone know how to fix this?

    I cannot access my mail from my ipad. I keep getting an error message "MFMessageErrorDomain error 1032"

    iOS: Unable to send or receive email
    http://support.apple.com/kb/TS3899
    Can’t Send Emails on iPad – Troubleshooting Steps
    http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
    Setting up and troubleshooting Mail
    http://www.apple.com/support/ipad/assistant/mail/
    Server does not allow relaying email error, fix
    http://appletoolbox.com/2012/01/server-does-not-allow-relaying-email-error-fix/
    Why Does My iPad Say "Cannot Connect to Server"?
    http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
    iOS: 'Mailbox Locked', account is in use on another device, or prompt to re-enter POP3 password
    http://support.apple.com/kb/ts2621
    iPad Mail
    http://www.apple.com/support/ipad/mail/
    Configuration problems with IMAP e-mail on iOS with a non-standard SSL port.
    http://colinrobbins.me/2013/02/09/configuration-problems-with-imap-e-mail-on-ios -with-a-non-standard-ssl-port/
    Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts   Tap on the Account, then on the red button that says Remove Account.
     Cheers, Tom
    Tap Settings > Mail, Contacts, Calendar and delete your email account.
    Then tap Settings > Safari > and Tap Clear History and Clear Cookies and Data.
    Now tap Settings > Mail, Contacts, Calendar and re-enter your email account credentials.
    Message was edited by: Texas Mac Man

  • Cannot access a work IP address

    I am working from a MacBook Pro. I work from home. I cannot access two work websites. I also cannot access my work e-mail. My two work websites have the same IP address. I had AT&T come out after extensive time on the phone with their 2nd tier tech group help me. They eventually replaced my modem. Once the modem was replaced it worked flawlessly until the next day when I tried to access the two websites and also e-mail. I thought it was an AT&T issue so I switched over to Time Warner. Once again with the new modem it worked flawlessly. Next day fail. I cannot ping the IP address and I have also have cleared the Cache, cookies, and history. I am running an OS X Maverick. If I turn on my hotspot on my phone I am able to access the websites and my work e-mail but that would end up being so costly to run this data 8 hours a day on my phone.
    When I am working I sit on these 2 websites for 5 to 6 hours a day because I need to access information.

    Hi.
    It is true.
    A reason is the SSO cookies mechanism, and it cannot work without a hostname.
    about this procedure: http://help.sap.com/saphelp_nw2004s/helpdata/en/28/7c383f717b5f03e10000000a114084/frameset.htm
    And similar answered questions:
    Re: Portal URL: Why cannot access via IP address?
    Facing Issues in accessing Portal through IP
    Re: After the login, the portal displays again the login page
    regards.
    Leandro

  • Cannot access old backups

    So here's the problem from start to finish:
    A while back I was experiencing some trouble with my Time Machine backups - they just kept failing. So I turned off time machine on my machine, de-selected the Time Capsule as my backup point, and rebooted the time capsule. Popped on time machine again, reselected "data" and then away we went with the backup. I was a bit concerned by the fact that it said "oldest backup: none" but then discovered that when it started backing up it wasn't doing my whole hard drive just a block of close to 50 gigs or so -- seemed within reason.
    Today I went to try and grab a file from a few months back only to discover I could only go back as far as Feb 8th (around the time when I re-setup time machine). There were entries dating back almost a year, which I expected but all of the items were "faded". They had dates - I could jump to March 17th for example, but when I got there I was greeted by a black box and no ability to pull anything down from time machine.
    I thought maybe it was this folder - but nope, tried a couple others and they were all the same.
    I only have one sparse bundle for this computer on the time capsule "data" drive, and it's ~1.5 TB in size. When I open up the sparse bundle and look there are lots and lots of folders (granted if I try to open any finder just shows the pinwheel in the lower right corner and does nothing) so I'm guessing that things are still there... but for some reason I cannot access them.
    Does anyone have any idea what might be going on? Are my files still there? Is my sparse bundle corrupt? Is it because this is all over the network? Is there a way to copy the contents of the time capsule over to another harddrive which I can then use in it's place?
    This is for my "old" computer, that has recently been replaced. My new computer is currently not being backed up at all because there's no room left on the time capsule because of the giant backup for my old computer, a backup I'm now not even sure really exists. If that's the case I'll just re-format the harddrive and away we go.
    Any insight that could be offered would be greatly appreciated.

    Are you on Mavericks now??
    Did the problem start when you upgraded to Mavericks?? If so you are one amongst many.
    Mavericks does something terrible to the old backups. If you can get access to them is unknown.
    Firstly mount the sparsebundle and do a verify via disk utility.
    See A5 here. http://pondini.org/TM/Troubleshooting.html
    Try some of the solutions in the E section.. eg E2-E4
    I hope you do realise if you deleted the file from the computer.. then TM will delete it from the backup.. not immediately but eventually it will. TM is not a good way to keep history of backups.. It is a current snapshot.
    It sounds like you have tried correctly to open the sparsebundle in finder and locate the file.. This is worth while continuing but you just have to persevere .. open many dates around when you know the file was there. If it is gone.. well sorry it is gone.
    TM is not particularly reliable now since Mavericks. you haven't told me you are on Mavericks but the issues smell like that.

Maybe you are looking for

  • DNS Settings for multiple domains internal and external.

    First forgive me if my post is in the wrong area. If it is, kindly show me to the right location.. OK, here is the deal. I have an xserve running 10.5.6 perfectly. 5 Domains running on it as well perfectly fine. lets call them domain1, domain2, etc..

  • Trouble with redeeming 12 month creative cloud membership

    Hello, I purchased a 12 month subsricption to the creative cloud from best buy a couple of days ago. Earlier today I tried to redeem the membership. The Screen told me that the code was invalid. I tried plugging the code in several times. I even trie

  • Comparing Cost Center in ME23N and Goods Receipt document

    Hi, I do not have much functional knowledge in MM and I want to clarify following queries. I have to build a report that displays the Purchase order value and goods receipt value by cost center ( in the same output screen). In tcode ME23N of ECC, for

  • Combining two Object fields to one

    Hi,   I have an Array of objects bound to my data grid.   how can I have one column display both LastName + First Initial.   Last Name and First Initial are individual values in the object. <mx:AdvancedDataGridColumn  id="FullName" headerText="Name"

  • I face problem with the billing

    II face problem with the billing information of the visa