I get a nimax.exe- Application Error every time I start labview

every time I start a vi either by double clicking or by opening labview first I get an application error... "the instruction at "0x1ca12b96" referenced at "0x00000000", The memory could not be "read", click ok to terminate the program". when I click ok the program does not terminate and as long as I don't close labview completely I can close it and reopen the vi. I am unsure if the program malfuncions after that point but it is certainly an annoyance. Have you seen this problem before? Is there something that I should do to the vi to correct the problem? Thanks,
David Long
K.H. Controls

I talked to NI about this issue, and tried the following WITH success (note that I am running W2k and Labview 6.0.2):
1. Uninstall all NI components in the reverse order you installed them. For me, this was Ni-Daq, Ni-488.2, and finally Labview 6.0. If you have to, look at the modified or created dates of the folders to see what order you did it in.
2. After this, I decided to go a bit further and delete the registry key for Ni-Daq under HKEY_LOCAL_MACHINE\SOFTWARE\National Instruments\NI-DAQ. Make sure you Export your registry key beforehand in case something goes wrong.
3. Install Labview 6.0, custom installation. For this installation, DO NOT INSTALL the drivers, just Labview.
4. After that, I installed the upgrade patch for Labview 6i -> 6.0.2, downloaded at ni.com.
5. Next I downloaded the 2 files for NI-DAQ 6.9.3, uncompressed the files, and ran the setup. When the installation was done, I chose to not reboot now, but let me do it later. At one of these points, you can also Mass compile the VI's. I don't think it's necessary at this point, but I did it anyway.
6. Finally, I downloaded NI-488.2 version 2.2 (which has a new version of MAX than NI-DAQ 6.9.3), uncompressed it and installed it.
7. After this last step, I rebooted the computer and was able to finally get into MAX to configure my DAQ card.
So far, this method has worked. Perhaps it can work for you.

Similar Messages

Error updating mutation history every time I start LabVIEW

I have a slightly annoying problem that has been re-occuring the past month or so. Every time I start LabVIEW I get the following error messages:
Error occured updating the mutation history for Progam (2).lvclass. All values of this class in controls and constants will be reset to the default value
The same error appears for Page (2).lvclass, Chart (2).lvclass, Worksheet (2).lvclass and Workbook (2).lvclass.
It slows down my LabVIEW startup time by at least 3-4 minutes every time, which is quite annoying. I imagine the problem is occuring when it populates my existing projects, and in one of these projects contains the problem lvclass files. But I did a search of my ProgramFiles\NationalIntruments folder and my work directory and didn't find any files of those names. Just wondering if any one had any ideas on how to fix it?
Thanks!

Okay, seems like I found the problem. Yes, to answer your question, most of my LabVIEW programming is OO, using GOOP mainly.
I also imported hundreds of LabVIEW libraries where these lvclass files were, they were in ImportedLib\DataLogger\LabVIEW widgets\ActiveX
It's not code I've written, but I don't see why including these files was necessary in the repo, oh well. To get rid of the error I just removed those files and the mutation error stopped appearing. What's still a little confusing is why these files were being accessed on LabVIEW startup. I can imagine it necessary to load these files when the project is opened, but seems weird when it's just populating the existing projects list.
Oh well, thanks for looking into it Andy, files were not in the NI folder which explains why I didn't find them on my first attempt.

Get a 'Server Busy' message pretty much every time I start Lightroom

This is my Lightroom setup - pretty much every time I start Lightroom, I get the screen below;
Lightroom version: 5.7.1 [994254]
License type: Creative Cloud
Operating system: Windows 7 Business Edition
Version: 6.1 [7601]
Application architecture: x64
System architecture: x64
Logical processor count: 8
Processor speed: 2.9 GHz
Built-in memory: 7127.1 MB
Real memory available to Lightroom: 7127.1 MB
Real memory used by Lightroom: 639.7 MB (8.9%)
Virtual memory used by Lightroom: 608.8 MB
Memory cache size: 86.3 MB
Maximum thread count used by Camera Raw: 4
System DPI setting: 96 DPI
Desktop composition enabled: Yes
Displays: 1) 1440x900, 2) 1280x1024
Application folder: C:\Program Files\Adobe\Adobe Photoshop Lightroom 5.7.1
Library Path: C:\Users\Desktop\Pictures\Lightroom\Lightroom 5 Catalog.lrcat
Settings Folder: C:\Users\Desktop\AppData\Roaming\Adobe\Lightroom
Installed Plugins:
1) Flickr
2) HDR Efex Pro 2
3) Nikon Tether Plugin
4) Perfect Effects 8
Config.lua flags: None
Adapter #1: Vendor : 10de
    Device : dc4
    Subsystem : 23601462
    Revision : a1
    Video Memory : 977
AudioDeviceIOBlockSize: 1024
AudioDeviceName: Speakers (Realtek High Definition Audio)
AudioDeviceNumberOfChannels: 2
AudioDeviceSampleRate: 44100
Build: Uninitialized
CardID: 3524
Direct2DEnabled: false
GPUDevice: D3D
MaxTexture2DSize: 8192
OGLEnabled: true
Renderer: NVIDIA GeForce GTS 450
ShaderModel: 11.1
Vendor: Nvidia
VendorID: 4318
Version: 10de:0dc4:23601462:00a1
What does this mean and how can it be stopped?

No reply? No fix? I have the same annoying issue and its persistent. I has rendered LR totally unusable. WTF is going on? Force quit --> Re-open --> Same error --> Force quit --> etc.

"investigate previous internal error" every time I start LV 8.2.1

Hi,
Every time I start LV 8.2.1 I get a message "The last time you ran LabVIEW, an internal error or crash occurred at fpsane.cpp, line 401" and it asks if I want to investigate now. I don't have any problems while running the application, compiling it or building an installer. Does anyone have any idea what this is and if it's important?
Thanks,
Danielle
"Wisdom comes from experience. Experience is often a result of lack of wisdom.”
― Terry Pratchett

Although the VI runs, it may have a strange entry somewhere.
I did get that message a couple of times. From what I can recall it was when running omething & I had to kill the execution, or shut down LV completely. Upon re-start of LV a similar message popped up. The message did not re-appear at the next start. Maybe I inadvertently fixed it without knowing..
Try loading your VI, running it once. Saving it. Shut down LV. Restart LV. And check to see if the message continuous to appear. (you may have to repeat the steps once).
Oh... Do you have any Disable Structure which has some unfinished code iside it? I do recall that... Who knows.. (???)
RayR

I get an error every time i start my muvo tx

Because i didnt shut down the muvo tx fm mp3 player properly when i was done with writing music it started to turn off whenever i turned it on. I checked the manual and it said that i had to format it, but only format FAT files only. I accidentally didnt select that option. Now every time i try to open the mp3 player i get an error message saying: File System Error. What should i do?
ps: i have tried scan disc.

I had that problem with my MuVo TX fm as well. What I did was I went to format it again, this time choosing the proper option, and that seemed to work.

How can I get rid of this that shows up every time I start my Mac?

“/Library/StartupItems/AdobeVersionCue” has not been started because it does not have the proper security settings.
It started to show up when moving from CS4 and up. I am currently a Creative Cloud user
Thanks

Hi RicardoGonzalez,
Welcome to Adobe Forums.
Please open the finder window click on "go" and choose "computer".
Navigate to MacHD/Library/Startupitems and send AdobeVersionCue to Desktop or some other location on the hard drive.
Then try to launch your application and check if the issue persists.
Thanks

LabVIEW 2011 starts with an error every time on OS X

I get this error dialog every time I start LabVIEW 2011 on my Mac.
OS X 10.6.8
LabVIEW 11.0 Student edition
+Control system toolbox
+MathScript RT
Attachments:
Screen shot 2012-06-22 at 12.22.02 AM.png ‏37 KB

It has given this error every time LabVIEW has started up. This is a fresh install and it has done this every time.
Here is the log file:
#Date: Fri, Jun 22, 2012 1:01:30 AM
#OSName: Mac OS X
10.6.8
#OSVers: 10.6.8
#OSBuild: 10K549
#AppName: LabVIEW.app
#Version: 11.0
#AppKind: FDS
6/22/12 1:01:31.544 AM
DWarn 0xAFBF5C57: LabVIEW not initializing for Pro, Full or Student Edition. Undefined behavior may result.
LVLicenses.cpp(485) : DWarn: LabVIEW not initializing for Pro, Full or Student Edition. Undefined behavior may result.
$Id: //labview/branches/2011/dev/source/licensing/LVLicenses.cpp#9 $
0x0014D8D3 - __Z13CallErrorInfoPKclS0_17_DebugOutputLevelmS0_ + 49
0x021DAADB - _DebugOutputCallHandler + 45
0x021DA958 - __ZNK11DebugStream7ProcessEv + 3E
0x00B669CF - __ZN11CLVLicenses25CheckNonNILMFunctionalityEv + 3B5
0x00B66F43 - __ZN11CLVLicensesC1Ev + 41
0x00B66FB2 - __ZN11CLVLicenses26InitializeLVLicensesGlobalEv + 42
0x00B6723E - __ZN16LVLicenseService4InitEv + C
0x00710834 - __Z7InitAppv + BE
0x0071D2AC - __Z13AppInitializev + 85E
0x00723C09 - __Z15LVMainEventProcP6WEventl + 1B41
0x01638D90 - __Z17InternalEventProcP6WEvent + 20
0x0163FEB6 - _WSendEvent + 27E
0x00007844 - __Z13InitializeAppl + 54
0x00007136 - __Z6MGMainlPKPKc + 17E
0x000074E2 - _CommonMacMain + 1B8
0x00002C02 - <unknown> + 2B11
0x00002B29 - <unknown> + 2A38
0x00000002 - <unknown> + FFFFFF11

NImax.exe has generated errors. You must restart the program, a log file is being created.

NImax.exe has generated errors. You must restart the program, a log file is
being created.
This error occurs just after bootup, no programs started except windows..
Running Windows 2000 latest version on a brand new computer.
(pent 4 3.0 ghz 500MB ram).
Can anyone help me with this problem? Happened after install Labview 7.0
express. Installed twice and same problem occured with both installs.
Labview 7.0 is the only thing installed right now. Also selected "Visual
Basic Support" install from driver cd's.
One other thing I just noticed. System info reports 2 processors and I
think I only have one.
TIA

Happy update.
After ignoring this problem for awhile and installing some NI DAQ boards,
this problem is not happening anymore.
Would urge NI to investigate further though. Messed me up for a couple of
days, and still don't know why it happened.
Much thanks to those who helped.
JJ
"JJF" wrote in message
news:qB6Hb.48702$VB2.90660@attbi_s51...
> One other point, I found out this is a message generated by drwtsn32. Can
> get rid of the error by unchecking "show visual feedback on errors" box,
but
> don't like that fix. Still need help.
>
> Thanks,
>
> JJ
>
> "JJF" wrote in message
> news:%JRGb.138921$8y1.419649@attbi_s52...
> > Hi Nirmal and all,
> >
> > Happy Holidays to you too, and thanks for the reply.
> >
> > Making progress. Did all the uninstalling and registry editing as you
> > suggested. Also, updated Win2K at Microsoft.com as suggested.
> > Re-installed with default settings of LV express 7.0. Now I only get
> the
> > error when I exit NImax.
> >
> > Also, my p2p home network is not that hot. Have it set up as a
workgroup.
> > Sometimes when I boot up I have file access between the two computers
and
> > sometimes windows explorer can't find the workgroup network path
(between
> > the two computers). Both computers can always access the internet
though.
> > Using a 4 port Linksys cable/dsl router on a cable modem. Using XP
home
> > edition on base computer (the one set up for the isp) and Win2K on the
> other
> > computer.
> >
> > Also, any idea where this log file is going? Thought it was part of the
> > event viewer but the errors in the event viewer don't seem to correspond
> to
> > the NImax.exe logging event now. There is a file in
> > "winnt\sytem32\config\software.log" that seems to change at about the
same
> > time but I can't access the file because it is in use by the system.
> >
> > Using NImax ver 3.02.3005. Do you know if I can download "NI
measurement
> > and automation explorer" and/or the driver cd's from NI.com? Maybe I
have
> a
> > flaky disk or something. I have a feeling it may also have to do with
the
> > "on again/off again" network neighborhood connection problem.
> >
> >
> > Thanks again,
> >
> > JJ
> >
> >
> >
> > "Nirmal Sharma" wrote in message
> > news:506500000005000000AE470100-1068850981000@exchange.ni.com...
> > > Hi,
> > > Happy cristmas & new year for you & ur brand new pc...
> > >
> > > How are you uninstalling & then installing LV in your pc ?
> > >
> > > I suggest to remove complete LV (Remove All option) from your
> > > computer. Once uninstallation is completed, go to windows registry -
> > > by windows start -> run -> regedit -> Enter
> > >
> > > Goto HKEY_LOCAL_MACHINE-> SOFTWARE -> National Instruments - Delete
> > > this folder (National Instruments folder)
> > >
> > > Remove any other foloder/file related to NI's software. Be very
> > > cautious while deleting files from windows registry bcoz wrong file
> > > deletion may hang your whole system.
> > >
> > > Restart your computer..hope it should bootup without any errors.
> > >
> > > Now as answered by Alexander, update windows.
> > >
> > > After updating, bootup your system. If it boots up without any error
> > > message, install LV with the typical (default installation).
> > >
> > > Hope this helps. Your feedbacks are welcome.
> > >
> > > Best Regards,
> > > Nirmal Sharma
> > > India
> >
> >
>
>

NIMax.exe has generated errors

My system was working fine till this morning. I had to reconnect GPIB cables. I did that and ever since then, i'm unable to use MAX. As soon as i open MAX and click on "Devices and Interface", i get this error - "nimax.exe has generated errors and will be closed down by windows. You need to restart the program". I uninstalled LV 6.0 and MAX 3.1 and reinstalled LV 6.0 and MAX 3.2. The problem still is the same .. PLEASE HELP IMMEDIATELY !!!

Perhaps in the reinstallation of MAX the configuration data files have been corrupted. One way we can check this is to close MAX, and then delete the Data folder found in C:\Program Files\National Instruments\MAX. This will basically give you a clean slate in MAX to start from. WARNING: Deleting the Data folder will remove all MAX configurations. New configuration files will be created when MAX is reopened. If this is something that's possible for you, please try it, and let us know if it allows you to reopen MAX and move on. If not, we'll keep trying.
Logan S.

I keep getting error message "AppleSyncNotifier.exe - Entry Point Not Found" every time I start up my computer. How can I fix this

I recieve this message every time I start my computer, AppleSyncNotifier.exe - Entry Point Not Found. How can I fix this?

No problem.
You can either get it via Apple Software Update ("Start > All Programs > Apple Software Update" ... it'll appear in the "New programs" section) or by downloading an installer from the following page on the Apple Website:
http://support.apple.com/kb/DL769

I just downloaded itunes 10.5 and i get an error every time i hook up my mobile devices.

I just downloaded itunes 10.5 and i get an error every time i hook up my mobile devices.
And this is the error that comes out:
szAppName : AppleMobileDeviceService.exe szAppVer : 17.88.0.7
szModName : kernel32.dll szModVer : 5.1.2600.5781 offset : 00012afb

http://www.youtube.com/watch?v=be09gGFw-Y4

I have adobe CS 5.1 and recently (after an update) it is giving me an error (Could not save...because of a program error) every time I try to save my work as a PDF Help how can I get this resolved??

I have adobe CS 5.1 and recently (after an update) it is giving me an error (Could not save...because of a program error) every time I try to save my work as a PDF> Help how can I get this resolved??

Run the cleaner, reinstall.
Use the CC Cleaner Tool to solve installation problems | CC, CS3-CS6
And don't bother with running any updates unless you really need them or they fix a critical issue relevant to your workflow.
Mylenium

TS1424 Every time I start up iTunes I get this error message. "A required iTunes component is not installed. Please repair or reinstall iTunes (-42404). I have researched this on Google and I have not read of any solution to this. Please advise.

Him
Every time I start up iTunes I get this error message. "A required iTunes component is not installed. Please repair or reinstall iTunes (-42404)." I have researched this on Google and I have not read of any solution. Please advise.

Here you go: http://support.apple.com/kb/HT1923
There are three steps so make sure you follow all of them. They are:
remove iTunes and everthing related to it
verify everything is really removed
reinstall iTunes.

Every time I start Illustrator CS6 I get an error message: "Error loading plugin AIHostAdapter.aip.

Every time I start Illustrator CS6 I get an error message:
"Error loading plugin AIHostAdapter.aip. I have tried reloading the program, updating, everything. I've checked the forums but no one seems to have a solution

I am not sure. Here is a screenshot. Many people are having this problem. I am wondering what it is and what it does exactly and can't seem to find an answer to that question.
I deleted Illustrator CS6 yesterday and reloaded the program. I am on a Mac, Maverick 10.9. The strange thing is the dates. All plugins [in the file] correspond with the Illy CS6 reload except that particular Plugin?
Can I delete the file or is it a necessary plugin?

Why can't i launch the itunes? i get an error every time i do. but i've installed it properly. :((

why can't i launch the itunes? i get an error every time i do. but i've installed it properly. :((

Any error numbers given?
Did you try to remove and reinstall all Apple related software, as described in this article?
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

I get a nimax.exe- Applicatio​n Error every time I start labview

Similar Messages

Maybe you are looking for

I get a nimax.exe- Application Error every time I start labview