I upgraded to yosemite 10.10.1 on my 2012 macbook air. Wi-fi works and blue tooth works, but not at the same time. Now what?

My bluetooth seem to conflict with my wi fi. Both work with the other turned off.

In an area where your WiFi is not working, try System Preferences > Network > Assist Me > Diagnostics

Similar Messages

  • Installed Yosemite om my MacBook Air, resulted in no Sound at all. No input devices no output devices. What can  do? Have had 2 meetings with Apple support with no results.

    Recently, I installed Yosemite on my MacBook Air. After that I had no sound. Not even the start up chime. In Sound preferences there are no input devices and no output devices. I have had three meetings with Apple support with no results. Can anyone help? This seems to be a regular problem.

    Try these in order testing your system after each to see if it's back to normal:
    1. a. Resetting your Mac's PRAM and NVRAM
        b. Intel-based Macs: Resetting the System Management Controller (SMC)
    2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
         Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
         COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the
         computer and after the chime press and hold down the OPTION key until the boot manager
         screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
    4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible
                because it is three times faster than wireless.
    5. Reinstall Yosemite from Scratch:
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    How to Clean Install OS X Yosemite
    Note: You will need an active Internet connection. I suggest using Ethernet if possible
                because it is three times faster than wireless.

  • I am using several Macs running Yosemite. I was recently "upgraded" to Xfinity's new cable modem which can support both 2.5Ghz and 5Ghz networks at the same time. Actually I can connect to the internet over both with a satisfactory bump in speed for

    I am using several Macs running Yosemite. I was recently “upgraded” to Xfinity’s new cable modem which can support both 2.5Ghz and 5Ghz networks at the same time. Actually I can connect to the internet over both with a satisfactory bump in speed for the Ghz. However when I connect to the 5Ghz the Time capsule disappears from the Airport Utility and claims to be Not Found. Is there something I have done wrong or just a Yosemite Teething Problem

    First restart your mac and try again.
    It could be
    that the router and the TC are interfering wirelessly with each other.
    You can check this by pressing the option key while clicking on the wireless icon on your screen
    Open Wireless Diagnostics
    enter your user password
    Press CMD 4 then Scan
    You will see all the wireless channels being used in your location and you can check if they are on the same channel
    Make the SSID for the TC simple like MyTC
    Set 5Ghz to auto
    Update the TC
    Try again
    Ted

  • After installing the new Yosemite OS on my iMac I can no longer send email. I can receive email, but not send. I use gmail and can send email on the gmail (google) site, but not on "mail" on my iMac. Any others with this problem? What should we do?

    After installing the new Yosemite OS on my iMac I can no longer send email. I can receive email, but not send. I use gmail and can send email on the gmail (google) site, but not on "mail" on my iMac. Any others with this problem? What should we do?

    My gmail, which is correctly configured for Mail with gmail SMTP and Google IMAP, works for awhile on Mail, which I leave open while working on other applications. But several times a day I get msg from Google: "We recently blocked a sign-in attempt to your Google Account" . . . and requiring me to verify my account details, re-enter passwords, confirm security settings (or change them from "disable" to "enable less secure methods" and so on). In Mail I also have tried "taking all accounts online", and re-entering my gmail password inside Mail account settings. These steps successfully re-set comms between gmail and Mail ... for awhile, then it happens again. Enough occurrences over a work day that I just quit Mail and revert to accessing gmail directly. Apple Care advisor and an Apple knowledge base article say that Apple can't deal with this, as gmail is third-party app, and they refer me to gmail, and so far I've found nothing helpful there.
    From today I also have several instances of a window saying "Mail has unexpectedly closed" and asking me to Re-open it.
    I also use Yahoo mail, which stops working with Mac Mail at the same time as gmail, but I do not receive notices to re-verify from Yahoo.
    I recently upgraded from Mavericks to Yosemite. The Mail problem happened occasionally with Mavericks but is far more frequent with Yosemite.

  • My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

    My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

    OK great info!
    I found 2 possible ethernet to USB adapters:
    By "Plugable":  USB 2.0 to ethernet LAN wired network adapter - seems this will work, but I'll contact Plugable.
    2. Apple USB Ethernet Adapter
    Easily connect your MacBook Air computer to an Ethernet network with the Apple USB Ethernet Adapter. Small and light, it connects to the USB 2.0 port of your MacBook Air and provides an RJ-45 connector that supports 10/100BASE-T performance.  BUT NOT SURE IF THIS WILL WORK ON ANYTHING BUT a MacBook Air…
    One person commented: 
    This little gem used to be the device of choice for adding a second Ethernet interface to a Mac Mini Server and I'd been using one that way for about a year. After doing a software update to 10.6.6 it stopped working. Forewarned is forearmed – it appears that Apple is finally enforcing the MacBook Air system requirement.
    Thanks for any additional comments.
    Best regards,
    Steve Schulte
    Sunday 6 January 2013

  • Mid 2012 MacBook Air Yosemite Slow Booting and Old Boot Screen

    Hello Guys,
    I have a mid 2012 MacBook Air 13" and I had installed public beta of Yosemite on it. Now I am running OS X 10.10 (14A388b) and I have problems on the boot. On all the other macs, I saw that the booting screen is black background and a white Apple logo on it. But on my mac, the booting screen is same as Mavericks and for the first 5-6 seconds, the Apple logo doesn't show up. And the mac is booting very slowly. Also, Continuity and Handoff are not working properly. What might be the problem?

    Hello Guys,
    I have a mid 2012 MacBook Air 13" and I had installed public beta of Yosemite on it. Now I am running OS X 10.10 (14A388b) and I have problems on the boot. On all the other macs, I saw that the booting screen is black background and a white Apple logo on it. But on my mac, the booting screen is same as Mavericks and for the first 5-6 seconds, the Apple logo doesn't show up. And the mac is booting very slowly. Also, Continuity and Handoff are not working properly. What might be the problem?

  • I have recently upgraded to OSX 10.8.2 and now find that I cannot operate my scanner, an hp psc 1310 series printer/scanner. I get a message saying that Power PC is no longer supported. I am still able to print on the same device. What should I do?

    I have recently upgraded to OSX 10.8.2 and now find that I cannot operate my scanner, an hp psc 1310 series printer/scanner. I get a message saying that Power PC is no longer supported. I am still able to print on the same device. What should I do?

    Hi,
    PSC 1315 no longer supported for scanning since Mac OS X v10.5 or while using any newer OS, there is no scan software provided by either HP or Apple (Image Capture)
    You may find this information stated below for Leopard, the same apply for any newer OS version:
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01234231&cc=us&dlc=en&lc=en &os=219&product=374568&sw_lang=
    Image capture will not recognize your device as well, only print is supported as you may find listed for teh PSC 1310 Series below:
    http://support.apple.com/kb/HT3669#HP
    Although there is no official scanning support for your device you may still try the 3rd party VueScan software which list your scanner as supported and compatible with Mountain Lion:
    http://www.hamrick.com/vuescan/hp_psc_1310.html
    Shlomi

  • Who can shed some light on my ongoing connection problem. After upgrading my iPad Air with IOS 7.06, I could no longer connect to the internet. I have 2 MacBooks Air, 1 ipad mini and one iPhone 4S running on the same network, and they are all connected to

    Who can shed some light on my ongoing connection problem.
    After upgrading my iPad Air with IOS 7.06, I could no longer connect to the internet.
    I have 2 MacBooks Air, 1 ipad mini and one iPhone 4S running on the same network, and they are all connected to the net and function well.
    So I cleaned up the ipad completely, installed the latest firmware and reinstalled my apps : no connection.
    I tried all things of resets and forgets. No result.
    I have been fondling with my Airport Extreme 5 , but that did not help much.
    This morning I went to a neighbor , hooked my ipad air on his network, typed the password and the thing all worked fine.
    I have tried to connect the ipad air as an ethernet client, but that did not work. „Not enough power“ was the statement
    Ideas anyone ?

    Yes I tried this manyfold. But did not work.  Reading on, I took Tesserac's advice. Shut down router and computer.
    Start router after 15 minutes and wait another 10 minutes before starting the computer.
    Et voila.... everything is back in working order,
    Regards form Curacao, Dutch Caribean.
    Pete van Linden

  • After upgrading to the most recent version of iTunes, for the second time now, I have completely lost all of my playlists and some of my music

    I have upgraded to the current version of iTunes 12.0.1.26
    I am using Windows 7 Premium
    I have lost all of my previous playlists and some of my music
    This is the second time this has happened when advised of an updated version.
    How can I get all my music and playlists back without having to redo them again?

    Hello richmondhill49,
    The article linked below details a number of steps that may help restore your content and playlists to iTunes.
    No content shows up in iTunes after updating
    http://support.apple.com/kb/TS1967
    Cheers,
    Allen

  • Just installed a HP Color Laserjet CM2320nf MFP printer, at the same time I upgraded to Lion. It prints fine, but I cannot use the scan functions.  I downloaded the most recent driver! Any help would be appreciated.

    Just installed a HP Color Laserjet CM2320nf MFP printer, at the same time I upgraded to Lion. It prints fine, but I cannot use the scan functions.  I downloaded the most recent driver! Any help would be appreciated.

    HP says that the drivers for your all in one print/scanner are downloadable from apple. For the scanner to use preview. image capture or the scan icon from the print driver queue.  I don't know how old your HP is, but I know that the newer Os from apple don't support a lot of older printers. You might be able find a third party driver that could work.

  • Yosemite Freezing at the same time on 3 Mac Pros

    I've installed Yosemite on 3 Mac Pro's ( variety of models, 2010 and 2011)
    They are all regularly freezing up at exactly the same time.
    When I say freeze, I mean everything is unresponsive except the cursor still moves. The clock stops for the duration of the freeze, the macs lose their connection to the network ( I can't access them via ARD)
    They all burst back into life around 5 minutes later
    Sometimes the time between freezes is an hour, some times longer

    You can do it with Automator.
    http://www.automator.us/examples-01.html
    Or with a utilities like these:
    http://www.publicspace.net/ABetterFinderRename/
    http://renamer4mac.com/
    You can also do it using the Terminal command line.
    Matt

  • HT4528 Hello.  I recently upgraded my iPhone 4 to ios7.  Since the upgrade, my phone turns itself off at the same time every night, for about 30 minutes.  I have no idea why.  Any suggestions?

    I recently upgrade to iOS 7, and since then, my iPhone turns off automatically at the same time every night for about 30.  Why does this happen, and what setting can I change to prevent it?

    Is Do Not Disturb turned on? Do you see a quarter-moon icon up top in the status bar?

  • I have a MacBook pro version 10.6.7 with snow leopard. After an scheduled software upgrade I could not open Quicken (It said it could not open the files). Now I can only open it if I have my external drive on. Can you help?

    I have a MacBook pro version 10.6.7 with snow leopard. After an scheduled software upgrade I could not open Quicken (It said it could not open the files). Now I can only open it if I have my external drive on. Can you help?
    All the information that I had input on Quicken is gone. I have to have the external hard drive that I use to back up to be able to use quicken now. It is as if it was erased from the laptop hardrive

    Try repairing permissions. My favorite way is with a utility called AppleJack. Info and download here. It's free. It only works when you boot in Single User Mode. When restarting or booting, hold down the Command key and S keys.
    You will get a very different startup screen that looks like the Terminal app has hijacked the screen. Just let the lines of text scroll by. When that happens you will get a text entry prompt. Type in "AppleJack" without the quotation marks.
    A DOS looking menu will appear. Choose 1 or d to run Disk Repair. If you get a message that Disk Repair found and corrected errors, run it again. Repeat until you get the "your disk appears to be ok" message. This rarely happens with my experience, though. This does the same thing as as booting from an external drive and running Disk Utility's repair. Only, no external drive is required!
    Next, choose 2 or p to repair disk permissions. This will take a little while. AppleJack warns that it will take up to an half hour to run repair permissions. It'n never taken more than about ten minutes for my MacBook Pro.
    As permissions are repaired, you will see each repair scroll on the screen. When done, the menu returns, choose q to quit. Then at the prompt, enter "exit" without the quotes. Your MacBook Pro should restart into Mac OS normally after this.
    Hope this helps.

  • After Upgrading to 10.6.8 my aperture app starts but hangs trying to read the Lib. I removed the old lib and start with new. but still have the problem. 10.6.8 also made my Shark FX7 do the same thing. Any Ideas? Thanks

    After Upgrading to 10.6.8 my aperture app starts but hangs trying to read the Lib. I removed the old lib and start with new. but still have the problem. 10.6.8 also made my Shark FX7 do the same thing. Any Ideas? Thanks

    Verifying volume “Macintosh HD”
    Performing live verification.
    Checking Journaled HFS Plus volume.
    Checking extents overflow file.
    Checking catalog file.
    Checking multi-linked files.
    Checking catalog hierarchy.
    Checking extended attributes file.
    Checking volume bitmap.
    Checking volume information.
    The volume Macintosh HD appears to be OK.

  • I just upgraded to mountain lion. I am unable to use airplay mirroring through my apple tv. They are both on the same network. It says a airplay icon should appear in the menu bar but it isn't there. What am I missing here?

    I just upgraded to mountain lion. I am unable to use airplay mirroring through my apple tv. They are both on the same network. It says a airplay icon should appear in the menu bar but it isn't there. What am I missing here?

    http://www.apple.com/osx/specs/

Maybe you are looking for