Idoc packet size inbound

any idea on setting the inbound idoc packet size while mass processing

Hi,
If you set packet size as 10, if 1000 idocs reached to the system ,then 100 backgrounds jobs(program RBDAPP01 )will be executed to process these 1000 idocs.
Check this link :
http://www.dataxstream.com/doclib/ALEOptimization.pdf
Regards
L Appana

Similar Messages

Set idoc Packet Size to always be a single packet

Hi All,
WE20 config has a field for packet size. If I set it to 1, the system will create 1 packet/LUW for each idoc.
If I set it to two, it will wait until there are 2 idocs available and then create 1 packet/LUW for both idocs. however, if that second idoc is never created, the first idoc will never be sent.
Is there a way to specify that the system always send 1 packet/LUW for any number of idocs? So lets say today I created 10 idocs - the system would send that as 1 LUW. Tomorrow, I create 25 idocs, and the system would send that as 1 LUW.
I'm guessing the answer to this is NO, because the system will never know when to stop waiting for more idocs and send them to the receiving system already. The PI developers here are looking for a way to avoid implementing BPM, because they say it will cause performance issues. This was suggested as an alternative. As I said, I doubt it's possible, but I wanted to make certain before going back to them with that info.
Thanks,
Bryan

For some reason I was under the impression that RSEOUT00 wouldn't send the idocs unless the number had been reached, but I see that is not the case.
I always make things more complicated than they need to be.
Thanks!

Where do we control packet sizes in IDoc's processing.

Hi
Can you please let me know
1) how we can control the Packet Size while processing Idoc's?
2) How to find out how many Idoc's got / can be processed in one packet?
3) Where can these Packet size settings be made?
Satish.

Hi,
You can get control on indoc inbound processing only if the processing is "triggered by background program" in the partner profile.
>1) how we can control the Packet Size while processing Idoc's?
It is controlled in the variant of the RBDAPP01 program
>2) How to find out how many Idoc's got / can be processed in one packet?
This is tuning : you have to experiment to find out the best setup for your specific need.
It is not an easy task because it is not usually very easy to import a lot of idocs in a testbed system.
You have to find a compromise between speed (throughput) and resource consumption.
>3) Where can these Packet size settings be made?
Again in RBDAPP01 variant.
Best Regards,
Olivier

Configuring Packet size for IDOCS on outbound Side

Folks,
Can we configure the packet size for idocs on the onutbound side of the Adapter ?
Manish

Hi Manish,
It is posible if all 1000 idocs are of same Idoc type.
Jus go and change the occurene of Idoc in the XSD as 1..Unbounded. SO that your the message can hold multiple Idocs.
But let me clarify here, if you send 1000 idocs from R3 , it will come to XI as one-by-one. There is no mechanism to get 1000 idocs at a time. So you need to collec all the idocs and then send it.
Just have quick look into this
Packaging IDOCs - SAP R3(IDOCs) -> XI -> Flat File
Regards,
Moorthy

Getting error 51 saying 'IDoc included in IDoc packet containing an error'

When I am processing idoc in LSMW, getting error saying 'IDoc included in IDoc packet containing an error'.
Can any one tell me how to resolve this.

Hi,
Change the packet size to 1 then process again.

Getting error saying 'IDoc included in IDoc packet containing an error'.

hi experts
When I am processing idoc in LSMW, getting error saying 'IDoc included in IDoc packet containing an error'.I changed the packet size also but it was not resolved.
Can any one tell me how to resolve this.

Hi,
Check below link......
Getting error 51 saying 'IDoc included in IDoc packet containing an error'
even this link is not solving problem then check the aplication log to get exact error text.
Thanks,
Asit Purbey.

IDoc packets in SP11

Hi -
Support for collecting and sending IDocs in packets was supposed to be part of SP11.
The tuning guide mentions it on page 13:
"In SP11, a solution will be available for IDoc adapter outbound processing to collect IDoc-XML messages and transfer them as an IDoc package, as in the traditional IDoc world."
Was this actually implemented in SP11? I don't see any notes about it or any new parameters in the IDoc Communication Channel.
Thanks,
Jesse

Hi Kiran,
Thanks for your post. I have fully understand the link that you attached.
Basically my main concern now is on LUW that i mentioned in my earlier post. According to the eg that i given in my earlier post there are 120 total IDocs read, and 100 is the packets size that input in selection screen of program RBDAPP01.
So for this case, i know that program will process IDocs into 2 batches, 100 IDocs for 1st batch and 20 IDocs for 2nd batch. Since i have read through some source from internet(can't recall the web add) by saying that for the scenario above, program will post the 1st batch into single LUW and 2nd batch into another single LUW.
For this statement and example, im expecting if one of the IDoc facing update error in 1st batch (100 IDocs), then there is no update for the rest of 99. I have tested for this case, but system doesn't bundle them into single LUW. The result is 1 IDoc failed, the rest of 99 still got updated into system.
The result is totally conflict with what i have read. I'm banging my head now by reading the SAP std code to figure how the LUW works with Packets Size.
Could you please advice if i left out any config or my concept is wrong totally?
Thank you.

InfoPackage packet size

Hi all,
I've seen several threads regarding the customizing of the InfoPackage packet size. Basically, it says that I have to change it in "InfoPackage under Scheduler->Data Default Transfer" but I can't see this option there.
Is it only for the 3.5 version ? Does it work with a loading through a PSA ?
Thx in advance...

These settings apply to the creation of data pakcaets. Say you had 50000 records coming in 50 packets with default settings of 20000 and 10. In that case there would have been 5 Info Idocs.
Now if the settings are changed to say 10000 and 5, the number of data packates would become 100 and InfoIdocs 20 (one for every 5 data packets).
Lower the size of data packets, higher the no. of packets. All records still get extracted.
update rules run for a data packet at a time. If you are getting memory or performance problems in update rules, dropping the size of the data packet is an option. Lower no. of records to be processed per run of hte update rules.

Packet size in SAP 4.7

BW experts,
I need data packages from SAP 4.7 to get 50000 rows at one in a single packet. Right now in BW it is set to get 20000 max per packet. Where can I change it to get more per packet. I am not able to do it on BW side as it say the maximum source system will allow is 20000, where in the source system (SAP 4.7) can I make this change?
Thanks
Ashwin

Hi..
Configuring ROIDOCPRMS table
Transaction SBIW
General Settings->Maintain Control Parameters for Data Transfer
Refer OSS Note : 417307
About ROIDOCPRMS
It is an IDOC parameter source system. This table contains the details of the data transfer like the source system of the data, data packet size, maximum number of lines in a data packet, etc. The data packet size can be changed through the control parameters option on SBIW i.e., the contents of this table can be changed.
with regards,
harikv

The setting for packet size (RSCUSTV6)

HI Guys
i want to know the setting for packet size (RSCUSTV6). can i do in production . or dev.
i want change as
Packet size = 20000
FrequencyStatus-Idoc = 5
please advise on this.
Regards
siva

Hi Patel,
This will impact all the loads in the system as this wil change the parameters for all the loads.. And hence its always recommended to reduce the data packet size at the Infopackage level...
Also u can do the settings for the ODS Activation process as well using this RSCUSTV6 t-code.
Better chane it for the specific job.
thanks

Regrd the data packet size

Hi
i have two questions
1) where can i set the data packet size in BW and R3 and also in BI how and where can we set .
2)by what method/logic we will select the key fields in dso.
ex: i have 5 tables in the sourse and each table will have primary keys, now how do we know that particular primary keys should be kept in KEY FIELDS folder in DSO.
full points will be assigned.

HI,
Data package settings for the data to be extracted from R3 to BI can be done through :
1) SBIW>General Settings> Maintain Control Parameters for Data Transfer
These settings are common for all the info packages which extract data from R3.
2) If u want to do settings relevent to specific Infopackage then :
RSA1>Click On the Specific Infopackage>Scheduler(in the Menu Bar)-->DataS Default Data Transfer.
3) And if you want to do DSO Package settings then:
Got to Transaction RSODSO_SETTINGS
Here u can do package settings for DSO activation ,paramenter for SID generation ect.
And selection of Key fileds depends upon the requirement.
Based on the key fields what all the data fileds u want to overwrite or add the corespomding data fields
Regards,
Chaitanya.

How do I change packet size for a single load

All,
I need to change the packet size for a single load I'm doing. How do I set that?
Thanks.
Dave

Hi..........
For this u hav to go to the infopackage scheduler........
If u r in Process chain >> Right click on the infopackage >> Maintain variant..........then it will come to the IP scheduler..................In the Top Scheduler Tab >> Click on it and select DataS. Default data transfer .......Now there may be a delta IP and Full upload IP for the same datasource.......check ur IP .....it is full or delta..........if full change the packet size for full upload..............otherwise for delta upload........
If the IP is not a part of any Process chain..........then go to RSA1 >> Find the IP..........and double click on it........then the IP scheduler screen will open..........
You can make global settings for all datasources...... in the transaction SBIW in the area General Settings >> Maintain control Parameter for Data transfer......... The parameters that you maintain here are valid as global standard values, and thus apply to all DataSources.
Hope this helps.....
Regards,
Debjani........
Edited by: Debjani Mukherjee on Nov 13, 2008 2:19 PM

Idoc WHSORD for inbound delivery

Hello,
We want to send inbound deliveries to an external WMS (not SAP WM) by using an output in the inbound delivery.
I tried to use idoc WHSORD (basic type DELVRY01) as for Outbound delivery.
I obtained an error message when processing the output : "The message record of the message control contains a partner role with a partner type LS that cannot be used here. Only the 'KU' and 'LI' partner types are allowed."
<u>Configuration done</u> (same as outbound delivery) :
Output : Medium "6 EDI" / Partner type LS
Partner profile (WE20) : Partner type LS / Partner role LS /Message control : Application E1 / process code DELV.
Finally, I've been able to generate one idoc from the inbound delivery by using medium "A ALE" and partner type LI "vendor". But I need to do it for a LS partner as we do want to maintain partner profile for each vendor.
Is this due to some missing configuration linked to application E1 (i.e allow partner type LS ?) ?
How can we solve this ?
Thanks a lot for your help

Hi zhiqiang,
In order to test inbound idocs, you can use transaction WE19 to create manually idocs.
As pre-requisite, you have to maintain ALE configuration : port and partner profiles.
Then in WE19, you can create an idoc from message type : fill all the fields you need to and delete unuse segments. Then click on "Standard inbound" and your idoc will be received in your SAP system.
Check the status in transaction BD87.
To fill correctlly your idoc :
1. You can find documentation on message type in transaction WE60 (when you go in this transaction, check the documention is "active" => Goto => user settings => "Documentation output" and "field value output" must be ticked)
2. In WE19, for some fields, if you press F4, you will get list of possible values.
Good luck,
JP

IDoc included in IDoc packet containing an error: transfer it separately

Hi Gurus,
I'm having this problem in our ECC side. I already did what Michal said in his blog:
/people/michal.krawczyk2/blog/2005/12/04/xi-idoc-bundling--the-trick-with-the-occurance-change
I have bundled the multiple IDOCs into 1 MATMAS.
But I'm still having the error IDoc included in IDoc packet containing an error: transfer it separately.
I've searched in the forums and none of them worked for me.
Thanks in advance!

Disable packaging or change the Partner Profile on WE02 transaction to "process immediately" the IDOCS.
When you process the IDOCS in background mode, it will create packages (it is enabled by default), and in case any of them fail you won't be able to see the root cause, but will have to go to BD97 transaction to process them again. Therefore, please use the "process immediately" or disable packaging and then you will be able to either see the error or process it because it won't fail because of another IDOC.

Standard IDoc Type for Inbound NonPO Vendor Invoices - FB60

What should be the perfect standard IDoc Type for Inbound NonPO Vendor Invoice posting. Tcode FB60.
I found IDoc Type FIDCCP02 but the Function Module 'IDOC_INPUT_FIDCC2' for FIDCCP02 is not released.
In the same way many other standard function modules like - IDOC_INPUT_ACLPAY, IDOC_INPUT_FIDCCH, IDOC_INPUT_ACC_INVOICE_RECEIPT and few more are not released.
My question : If at all I have to use standard IDoc Type, Message type and Function module (Released) for Inbound NonPO Vendor Invoices, then what should be the solution from SAP ?
Thanks,
Veeru.

Hi,
IDOC_INPUT_FIDCC2 for FIDCCP02 works for us in ECC6.0
If you want Automatic tax calculation functionality using FIDCCP02.. then FIDCC2 is not correct message type for you. In that case you should probably go for :
Msg: INVOIC
Basic type: INVOIC02
FM: IDOC_INPUT_INVOIC_FI
Process code: INVF
Thanks,
Kumar

Idoc packet size inbound

Similar Messages

Maybe you are looking for