IGMP Querier with Bluecoat ProxySG

Hi all
I ran into a problem with VIP for high availability on Blue Coat ProxySG. Both ProxySG send multicast packets
to advise the other ProxySG that it is up and the priority is contained in the multicast packet, along with the IP address of the VIP and so on.
This worked fine with Catalyst switches. Unfortunately it does not work over the newly installed Nexus switches.
There is no Vlan interface on the switches. The Vlan is only trunked through.
I found a hint that IGMP Querier could solve this issue. After configuration of IGMP Querier end acitvating Multicast on ProxySG
a IGMP group is built and all seems fine.
In a trace I can see IGMP Queries leaving the Querier but no answer from both ProxySGs.
After 6 minutes (3 times Querier Interval) the group disappears and both Boxes become active.
The topology looks like this:
Bluecoat1 -----N2k------2*N5k-----2*N7k-------Inter Datacenter Link-------2*N7k------2*N5k-----N2k-----Bluecoat2
                                    vPC         vPC                                             vPC          vPC
On both N7k in the left Datacenter is a Querier configured:
vlan configuration 85
ip igmp snooping querier 10.101.22.7
# sh ip igmp snoop querier
Vlan IP Address       Version   Expires     Port
85    10.101.22.7      v3        00:01:22     Switch querier
I wonder if an additional setting has to be made. Could it be that the Bluecoats ignore IGMPv3?
I would be very grateful for a hint.
Many Thanks!
Regards,
Urs

Hi,
I am exeperiencing the same issue described above, with a similar network layout:
     BlueCoat1---N2K---2*N5K(vPC)---2*C6880(VSS)---Inter Datacenter Links---2*C6880(VSS)---2*N5K(vPC)---N2K---BlueCoat2
I have configured an IGMP querier in the BlueCoat VLANs on both 2*N5K(vPC), even if on one 2*N5K(vPC) should be enough.
For each VLAN I've used the same free IP-Address on all 4 N5K:
     Is that correct?
I am asking, bacause the Cisco-documetation says, that only the one with the "lowest IP-Address (?)" will be active:
     How should the IGMP-Querier-election work in my case?
Any help will be really appreciated.
Many thanks

Similar Messages

ISE 1.1.2 with Bluecoat ProxySG

Hi,
As I understand that Cisco ISE performs function as RADIUS server. So, if I use Bluecoat ProxySG as a RADIUS client. The authentication should work as it should, right.
I have try this with FreeRADIUS and Bluecoat ProxySG and its working fine.
Does anyone try this integration between ISE and Bluecoat ?
Sent from Cisco Technical Support Android App

Hi,
I am exeperiencing the same issue described above, with a similar network layout:
     BlueCoat1---N2K---2*N5K(vPC)---2*C6880(VSS)---Inter Datacenter Links---2*C6880(VSS)---2*N5K(vPC)---N2K---BlueCoat2
I have configured an IGMP querier in the BlueCoat VLANs on both 2*N5K(vPC), even if on one 2*N5K(vPC) should be enough.
For each VLAN I've used the same free IP-Address on all 4 N5K:
     Is that correct?
I am asking, bacause the Cisco-documetation says, that only the one with the "lowest IP-Address (?)" will be active:
     How should the IGMP-Querier-election work in my case?
Any help will be really appreciated.
Many thanks

IGMP Querier in VPC domain

Hi
I am a little confuse with igmp querier on Nexus 5548UP
I have the following configuration on both VPC peers:
vlan configuration 208
ip igmp snooping version 2
ip igmp snooping querier 192.168.201.104
But the question is shell I use the same IP for querier on both VPC peers or diffrent ?
Regs
Marcin

It doesn't matter. It's only a source address and nobody will send anything to that address. IGMP joins are sent to multicast address 224.1.1.1 .

Multicast filter on SG300-10 and IGMP Querier

Hi
We're currently testing the Cisco SG300-10 for use with multicast TV services/channels but we're having trouble configuring the switch. Our setup is that we have a TV provider which is multicasting all their TV services into the switch's port 3. The multicast packets of a TV-channel should only be forwarded to another port in the switch if a client sends a IGMP join (report) message to start receiving a service.
First we've tried to disable multicast broadcasting by enabling Bridge Multicast Filtering Status (manual chap 15, "Defining Multicast Properties") but multicast packets are still broadcast on all ports. How do we filter multicast packets so they're not broadcast on all ports?
Also we need the SG300-10 switch to run as IGMP Querier so clients report membership at a regular basis. We've tried enabling IGMP Querier (manual chap. 15 "Configuring IGMP snooping") but it always remain disabled and we never see any IGMP Query messages (we use Wireshark to check this). How do we enable IGMP Querier?
When I press Apply the "IGMP Querier Status" remain "Disabled" in the "IGMP Snooping" page. Also the IP-address I specify is never transferred to the "IGMP Snooping" page.
Here's the switch's configuration:
switch291c88#sh run
config-file-header
switch291c88
v1.2.7.76 / R750_NIK_1_2_584_002
CLI v1.0
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
bridge multicast filtering
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
ip igmp snooping vlan 1 querier
ip igmp snooping vlan 1 querier address 192.168.1.254
hostname switch291c88
username cisco password encrypted 33c887d388ad6255811e904795174e5bd8444d32 privilege 15
switch291c88#sh interface count
      Port       InUcastPkts InMcastPkts InBcastPkts    InOctets
      gi1            1859          40           31         346191
      gi2             0            0            0            0
      gi3             0         2636117         0        616850868
      gi4             0            0            0            0
      gi5             0            0            0            0
      gi6             0            0            0            0
      gi7             0            0            0            0
      gi8             0            0            0            0
      gi9             0            0            0            0
      gi10            0            0            0            0
      Port       OutUcastPkts OutMcastPkts OutBcastPkts OutOctets
      gi1            2896       2627863        122       617075328
      gi2             0            0            0            0
      gi3             0           778          150         148040
      gi4             0            0            0            0
      gi5             0            0            0            0
      gi6             0         2628132        153       614950172
      gi7             0            0            0            0
      gi8             0            0            0            0
      gi9             0            0            0            0
      gi10            0            0            0            0
       Ch        InUcastPkts InMcastPkts InBcastPkts    InOctets
      Po1             0            0            0            0
      Po2             0            0            0            0
      Po3             0            0            0            0
      Po4             0            0            0            0
      Po5             0            0            0            0
      Po6             0            0            0            0
      Po7             0            0            0            0
      Po8             0            0            0            0
       Ch        OutUcastPkts OutMcastPkts OutBcastPkts OutOctets
      Po1             0            0            0            0
      Po2             0            0            0            0
      Po3             0            0            0            0
      Po4             0            0            0            0
      Po5             0            0            0            0
      Po6             0            0            0            0
      Po7             0            0            0            0
      Po8             0            0            0            0

Hm, solved multicast by filtering "Unregistered Multicast" and IGMP Querier by enabling IGMP snooping.

How to create an ABAP Query with OR logical expression in the select-where

Hi,
In trying to create an ABAP query with parameters. So it will select data where fields are equal to the parameters entered. The default logical expression is SELECT.. WHERE... AND.. However I want to have an OR logical expression instead of AND.. how can I attain this??
Please help me on this.. Points will be rewarded.
Thanks a lot.
Regards,
Question Man

Hi Bhupal, Shanthi, and Saipriya,
Thanks for your replies. But that didn't answer my question.
Bhupal,
You cannot just replace AND with OR in an ABAP QUERY. ABAP QUERY is a self generated SAP code. You'll just declare the tables, input parameters and output fields to be displayed and it will create a SAP standard code. If you'll try to change the code and replace the AND with OR in the SAP standard code, the system will require you to enter access key/object key for that particular query.
Shanthi,
Yes, that is exactly what need to have. I need to retireve DATA whenever one of the conditions was satisfied.
Saipriya,
Like what I have said, this is a standard SAP code so we can't do your suggestion.
I have already tried to insert a code in the ABAP query (there's a part there wherein you can have extra code) but that didn't work. Can anybody help me on this.
Thanks a lot.
Points will be rewarded.
Regards,
Question Man

ACS 5.3.0.40 with Bluecoat Packetshaper via Radius Auth using PAP/CHAP

Hi,
We have a strange issue may be an known issue. We have the ACS 5.3.0.40 with Bluecoat Packetshaper (Packeteer) as the Radius Client and tried with PAP as well as CHAP with the suggested VSA. But once we try to authenticate with GUI in the PS end we get authentication failed. i.e its says invalid password but in the ACS end we get it as the Auth success log. We are not able to login to the PS as well. Anyone have any idea what is the issue anything to be done with the patch upgrade or any issue with the packetshaper??????
below is the logs in ACS server.
Logged At:        September 4,2012 4:10:26.250 PM
RADIUS Status: Authentication        succeeded
NAS Failure:
Username: knpdtf
MAC/IP Address:
Network        Device: Test-PS : 10.187.115.83:
Access Service: Radius Network
Identity        Store: Internal Users
Authorization Profiles: Permit Access
CTS        Security Group:
Authentication Method: PAP_ASCII
By
Karthik

Hi,
Do you have any special characters in the password? I would see if you can create an internal user in ACS and use a basic password (like cisco123) and see if the authentication will succeed. I have seen with some GUI based products that some special characters can cause some headaches.
thanks,
Tarik Admani
*Please rate helpful posts*

Error while trying to Execute the Query with Customer Exit

Hi Experts,
I am having a Query with Customer Exit, it is working fine for all the Employess, except for one. When i try to remove the Customer Exit it is working for her too. Below is the error i am getting.
system error in program SAPLLRK0 and form RSRDR; CHECK_NAV_INIT_BACK
Thanks,
Kris.

Hello Kris,
Are you working with multiprovider? Please check if OSS notes 813454,840080 or 578948 are applicable in your case.
Regards,
Praveen

Report on BEx query with 2 structures (one in rows and one in columns)

Hi, experts! I have to make Crystall report on BEx query with 2 structures, one in columns (with KF's), and one in rows. Is it possible to create such report? Because when I create such report, I cant see fields in structures, only characteristics fields.
Ok, I found samr problem in another thread. Sorry.
Edited by: Mikhail Sychev on Dec 5, 2009 9:53 PM

Hey Flora,
Happy to hear that its working now.
Answering your question, again its upto the connection and report format you are using. Based on your question i hope you your report output should be like this.
You cannot map to two labels for the series, again this report format is possible only in cross tab through Webi. I would suggest you to concatenate the material and month in a dimension in webi like below.
I have done the concatenation in excel level, i would suggest you to do that in webi. Try to reduce the formula as much in excel.
or
If you are using Query browser connection, then i would suggest you to create a separate report which will display the actual vs plan material wise, here you need to pass the material as a prompt.
Hope this helps in clear, please revert me for any clarification.

Query with bind variable, how can use it in managed bean ?

Hi
I create query with bind variable (BindControlTextValue), this query return description of value that i set in BindControlTextValue variable, how can i use this query in managed bean? I need to set this value in String parameter in managed bean.
Thanks

Put the query in a VO and execute it the usual way.
If you need to, you can write a parameterized method in VOImpl that executes the VO query with the parameter and then call that method from the UI (as a methodAction binding) either through the managed bean or via a direct button click on the page.

Report query with bind variable

Trying to create a report query for xsl-fo print. For output format I pick "derive from item" then pick the item name from the list, on the next screen, I paste the query with the bind variable. on the next step test query, I always get "data not found" regardless what value I type in. This is the same query that I ran under sql commands without any issues.
Does anyone run into the same issue as I have when attempted to create a query with bind var ? There is no problem creating a query without bind varibles. . thanks.
Munshar

Hi, please did you get any solution to this issue? I am having similar challenge right now.
select     EMP.DEPTNO as DEPTNO,
     DEPT.DNAME as DNAME,
     EMP.EMPNO as EMPNO,
     EMP.ENAME as ENAME,
     EMP.JOB as JOB,
     EMP.MGR as MGR,
     EMP.HIREDATE as HIREDATE,
     EMP.SAL as SAL
from     SCOTT.DEPT DEPT,
     SCOTT.EMP EMP
where EMP.DEPTNO=DEPT.DEPTNO
and      DEPT.DNAME =upper(:dname)
This run perfectly in sql developer, toad, and even inside publisher if I login directly to publisher to create report.
Generating this same query in shared component query builder and testing it returns no data found. If I remove the last line, it works. but with the last line, it return no data found. It seems no one has been able to provide solution to this issue

SQL query with Bind variable with slower execution plan

I have a 'normal' sql select-insert statement (not using bind variable) and it yields the following execution plan:-
Execution Plan
0 INSERT STATEMENT Optimizer=CHOOSE (Cost=7 Card=1 Bytes=148)
1 0 HASH JOIN (Cost=7 Card=1 Bytes=148)
2 1 TABLE ACCESS (BY INDEX ROWID) OF 'TABLEA' (Cost=4 Card=1 Bytes=100)
3 2 INDEX (RANGE SCAN) OF 'TABLEA_IDX_2' (NON-UNIQUE) (Cost=3 Card=1)
4 1 INDEX (FAST FULL SCAN) OF 'TABLEB_IDX_003' (NON-UNIQUE)
(Cost=2 Card=135 Bytes=6480)
Statistics
0 recursive calls
18 db block gets
15558 consistent gets
47 physical reads
9896 redo size
423 bytes sent via SQL*Net to client
1095 bytes received via SQL*Net from client
3 SQL*Net roundtrips to/from client
1 sorts (memory)
0 sorts (disk)
55 rows processed
I have the same query but instead running using bind variable (I test it with both oracle form and SQL*plus), it takes considerably longer with a different execution plan:-
Execution Plan
0 INSERT STATEMENT Optimizer=CHOOSE (Cost=407 Card=1 Bytes=148)
1 0 TABLE ACCESS (BY INDEX ROWID) OF 'TABLEA' (Cost=3 Card=1 Bytes=100)
2 1 NESTED LOOPS (Cost=407 Card=1 Bytes=148)
3 2 INDEX (FAST FULL SCAN) OF TABLEB_IDX_003' (NON-UNIQUE) (Cost=2 Card=135 Bytes=6480)
4 2 INDEX (RANGE SCAN) OF 'TABLEA_IDX_2' (NON-UNIQUE) (Cost=2 Card=1)
Statistics
0 recursive calls
12 db block gets
3003199 consistent gets
54 physical reads
9448 redo size
423 bytes sent via SQL*Net to client
1258 bytes received via SQL*Net from client
3 SQL*Net roundtrips to/from client
1 sorts (memory)
0 sorts (disk)
55 rows processed
TABLEA has around 3million record while TABLEB has 300 records. Is there anyway I can improve the speed of the sql query with bind variable? I have DBA Access to the database
Regards
Ivan

Many thanks for your reply.
I have run the statistic already for the both tableA and tableB as well all the indexes associated with both table (using dbms_stats, I am on 9i db ) but not the indexed columns.
for table I use:-
begin
dbms_stats.gather_table_stats(ownname=> 'IVAN', tabname=> 'TABLEA', partname=> NULL);
end;
for index I use:-
begin
dbms_stats.gather_index_stats(ownname=> 'IVAN', indname=> 'TABLEB_IDX_003', partname=> NULL);
end;
Is it possible to show me a sample of how to collect statisc for INDEX columns stats?
regards
Ivan

Query with tables VEPVG, VBAK, VBAP AND KONV

hi all,
I have a requirement, that is Open Sale Orders which is having Special Discount. I am trying to write a Query, But KONV table is not coming into the joins. my execution plans is bellow
VEPVG --> VBAK vbak-knumv = konv-knumv and konv-kschl = Special Discount
VBAP
Please explain me, how to design the query with conditions.
Thanks & Regards,
Srinivas

Hi,
Have you referred this help document.
http://help.sap.com/printdocu/core/Print46c/EN/data/pdf/BCSRVQUE/BCSRVQUE.pdf
Regards - Shree

SQL Report query with condition (multiple parameters) in apex item?

Hello all,
I have a little problem and can't find a solution.
I need to create reports based on a SQL query or I.R. Nothing hard there.
Then I need to add the WHERE clause dynamically with javascript from an Apex item.
Again not very hard. I defined an Apex item, set my query like this "SELECT * FROM MYTAB WHERE COL1 = :P1_SEARCH" and then I call the page setting the P1_SEARCH value. For instance COL1 is rowid. It works fine.
But here is my problem. Let's consider that P1_SEARCH will contain several rowids and that I don't know the number of those values,
(no I won't create a lot of items and build a query with so many OR!), I would like sotheming like "SELECT * FROM MYTAB WHERE ROWID IN (:P1_SEARCH) with something like : ROWID1,ROWID2 in P1_SEARCH.
I also tried : 'ROWID1,ROWID2' and 'ROWID1','ROWID2'
but I can't get anything else than filter error. It works with IN with one value but as soon as there are two values or more, it seems than Apex can't read the string.
How could I do that, please?
Thanks for your help.
Max

mnoscars wrote:
But here is my problem. Let's consider that P1_SEARCH will contain several rowids and that I don't know the number of those values,
(no I won't create a lot of items and build a query with so many OR!), I would like sotheming like "SELECT * FROM MYTAB WHERE ROWID IN (:P1_SEARCH) with something like : ROWID1,ROWID2 in P1_SEARCH.
I also tried : 'ROWID1,ROWID2' and 'ROWID1','ROWID2'
but I can't get anything else than filter error. It works with IN with one value but as soon as there are two values or more, it seems than Apex can't read the string.For a standard report, see +{message:id=9609120}+
For an IR—and improved security avoiding the risk of SQL Injection—use a <a href="http://download.oracle.com/docs/cd/E17556_01/doc/apirefs.40/e15519/apex_collection.htm#CACFAICJ">collection</a> containing the values in a column instead of a CSV list:
{code}
SELECT * FROM MYTAB WHERE ROWID IN (SELECT c001 FROM apex_collections WHERE collection_name = 'P1_SEARCH')
{code}
(Please close duplicate threads spawned by your original question.)

Broadcast a BW 7.0 query with BW 3.5 broadcaster?

Hi Folks,
is there a trick that allows to broadcast a BW 7.0 query with the BW 3.5 broadcaster?
On the precal server BEX 3.5 / 7.0 is installed so in theory there shouldn't be an issue.
But in the BW 3.5 broadcaster I don't see BEX 7.0 queries as all (for html) nor BEX 7.0 workbooks.
As we don't have BI JAVA stack we don't have BW 7.0 broadcaster ...
Any ideas / workarounds / tricks?
Thanks,
Axel

Hi,
Pls check the links----
Issues with broadcasting 3.5 workbooks after migration to 7.1
Broadcaster not working from BEX Analyzer 7.0
Not able to broadcast query.
Regards,
Suman

Report and ready for input Query, with similar shadings are confusing

Some customers mix report and planning queries in their templates.
usually the shades for PLAN Queries are
o white - ready vor input
o blue- display data (e.g. LY, calc KPI)
In a Query with NO INPUT ready Cells the query has a zebra shading, blue and white, row by row.
That is confusion for users if they believe every Number on a white background can be changed.
Is it possible to change the shading for reporting queries to blue only?
Best Regards,
Georg

Hi.
You can cancel zebra by setting off for ALTERNATE_STYLES in properties if analysis item in WAD, BUT it sets all cells as WHITE and not blue.
I dont know how it will be usefull, but you may try ...
Regards.

IGMP Querier with Bluecoat ProxySG

Similar Messages

Maybe you are looking for