InstallBootFilesForImage failed 0x80004005

Hello all,
I enabled PXE boot for OS deployment, at first it didn't work, but once I injected the NIC drivers, it started to work.
After I was able to Build and Capture a Windows 8.1 image, I injected all the other drivers for our laptop... after that, I was getting PXE-MOF errors
again, so I removed all the drivers except for my NIC driver. Ever since then I'm still unable to get PXE to work.
Here's the troubleshooting I've tried so far.
Removed all drivers, and re-added only the NIC drivers from SCCM
Updated the boot image distributions in SCCM
Replaced the boot image in WDS
Removed and re-added the boot images, then replaced the boot image in WDS again
Re-installed WDS, .NET Frameworks 3.5 (I was getting errors updating distribution points, and this fixed it)
removed and re-added my distribution Points and management points, also configured the PXE boot options several times on both WDS and DP
I'm getting the following error
TFTP Download: smsboot\x64\abortpxe.com
Here are my error logs
SMSPXE.log
InstallBootFilesForImage failed. 0x80004005
SMSPXE
12/16/2013 11:36:45 AM
5956 (0x1744) Warning: Failed to copy the needed boot binaries from the boot image E:\RemoteInstall\SMSImages\OSD00005\boot.OSD00005.wim.
The operation completed successfully. (Error: 00000000; Source: Windows)
SMSPXE
12/16/2013 11:36:45 AM    5956 (0x1744)
Failed adding image E:\RemoteInstall\SMSImages\OSD00005\boot.OSD00005.wim. Will Retry..
Unspecified error (Error: 80004005; Source: Windows)
SMSPXE
12/16/2013 11:36:45 AM
5956 (0x1744)
Distmgr.log
MsiEnumRelatedProducts failed           SMS_DISTRIBUTION_MANAGER 12/16/2013 11:36:47 AM
3572 (0x0DF4)
FindProduct failed; 0x80070103          SMS_DISTRIBUTION_MANAGER 12/16/2013 11:36:47 AM
3572 (0x0DF4)
MsiEnumRelatedProducts failed           SMS_DISTRIBUTION_MANAGER 12/16/2013 11:36:47 AM
3572 (0x0DF4)
FindProduct failed; 0x80070103          SMS_DISTRIBUTION_MANAGER 12/16/2013 11:36:47 AM
3572 (0x0DF4)
I’ve noticed that if I were to uncheck “Allow this distribution point to respond to incoming PXE requests” in my DP properties in SCCM, WDS does
respond to PXE requests, but gets error “X:\Windows\System32>wpeinit”
the error "MsiEnumRelatedProducts failed" was fixed with a re-install in the .NET frameworks 3.5, seemed to re-appear

Hi Joyce,
Thanks for replying, error logs are below
Errors on distmgr.log
MsiEnumRelatedProducts failed~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.209+300><thread=2668 (0xA6C)>
FindProduct failed; 0x80070103~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.209+300><thread=2668 (0xA6C)>
MsiEnumRelatedProducts failed~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.209+300><thread=2668 (0xA6C)>
FindProduct failed; 0x80070103~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.209+300><thread=2668 (0xA6C)>
Found C:\Windows\system32\wimgapi.dll~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.209+300><thread=2668 (0xA6C)>
SetNamedSecurityInfo() failed.~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.212+300><thread=2668 (0xA6C)>
SetObjectOwner() failed. 0x80070002.~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.212+300><thread=2668 (0xA6C)>
SetFileSecurity() failed.~ $$<SMS_DISTRIBUTION_MANAGER><12-19-2013 15:21:01.212+300><thread=2668 (0xA6C)>
Errors on SMSPXE.log
<![LOG[InstallBootFilesForImage failed. 0x80004005]LOG]!><time="15:20:59.026+300" date="12-19-2013" component="SMSPXE" context="" type="3" thread="4160" file="bootimagemgr.cpp:1608">
<![LOG[Warning: Failed to copy the needed boot binaries from the boot image E:\RemoteInstall\SMSImages\OSD00003\boot.OSD00003.wim.
The operation completed successfully. (Error: 00000000; Source: Windows)]LOG]!><time="15:20:59.026+300" date="12-19-2013" component="SMSPXE" context="" type="3" thread="4160" file="bootimagemgr.cpp:1275">
<![LOG[Failed adding image E:\RemoteInstall\SMSImages\OSD00003\boot.OSD00003.wim. Will Retry..
Unspecified error (Error: 80004005; Source: Windows)]LOG]!><time="15:20:59.026+300" date="12-19-2013" component="SMSPXE" context="" type="3" thread="4160" file="bootimagemgr.cpp:1180">
<![LOG[File E:\RemoteInstall\SMSTemp\2013.12.19.15.20.58.02.{DB391A46-CCCA-4351-B5EA-867640529B85}.boot.bcd deleted.]LOG]!><time="15:20:59.026+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="4160" file="bootimagecache.cpp:267">
<![LOG[File E:\RemoteInstall\SMSTemp\2013.12.19.15.20.58.02.{DB391A46-CCCA-4351-B5EA-867640529B85}.boot.bcd.log deleted.]LOG]!><time="15:20:59.026+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="4160" file="bootimagecache.cpp:282">
<![LOG[Begin validation of Certificate [Thumbprint 3C176B3ADE0701F19A7C2C81D16253FA185D0757] issued to 'd0ffb6c3-7ac6-4d5b-b5b0-df0e81aedf7d']LOG]!><time="15:20:59.033+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="4160" file="ccmcert.cpp:1662">
<![LOG[Completed validation of Certificate [Thumbprint 3C176B3ADE0701F19A7C2C81D16253FA185D0757] issued to 'd0ffb6c3-7ac6-4d5b-b5b0-df0e81aedf7d']LOG]!><time="15:20:59.033+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="4160"
file="ccmcert.cpp:1803">
<![LOG[PXE Provider finished loading.]LOG]!><time="15:20:59.033+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="4160" file="smspxe.cpp:184">
<![LOG[Found new image OSD00002]LOG]!><time="15:20:59.034+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="2192" file="bootimagemgr.cpp:1123">
<![LOG[Loaded C:\Program Files (x86)\Windows Kits\8.1\Assessment and Deployment Kit\Deployment Tools\amd64\DISM\wimgapi.dll]LOG]!><time="15:20:59.034+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="2192" file="wimfile.cpp:334">
<![LOG[Opening image file E:\RemoteInstall\SMSImages\OSD00002\boot.OSD00002.wim]LOG]!><time="15:20:59.034+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="2192" file="wimfile.cpp:412">
<![LOG[Found Image file: E:\RemoteInstall\SMSImages\OSD00002\boot.OSD00002.wim
PackageID: OSD00002
ProductName: Microsoft® Windows® Operating System
Architecture: 0
Description: Microsoft Windows PE (x86)
Version:
Creator:
SystemDir: WINDOWS
]LOG]!><time="15:20:59.037+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="2192" file="bootimagemgr.cpp:925">
<![LOG[Closing image file E:\RemoteInstall\SMSImages\OSD00002\boot.OSD00002.wim]LOG]!><time="15:20:59.037+300" date="12-19-2013" component="SMSPXE" context="" type="1" thread="2192" file="wimfile.cpp:448">
<![LOG[InstallBootFilesForImage failed. 0x80004005]LOG]!><time="15:20:59.406+300" date="12-19-2013" component="SMSPXE" context="" type="3" thread="2192" file="bootimagemgr.cpp:1608">
<![LOG[Warning: Failed to copy the needed boot binaries from the boot image E:\RemoteInstall\SMSImages\OSD00002\boot.OSD00002.wim.
The operation completed successfully. (Error: 00000000; Source: Windows)]LOG]!><time="15:20:59.406+300" date="12-19-2013" component="SMSPXE" context="" type="3" thread="2192" file="bootimagemgr.cpp:1275">
<![LOG[Failed adding image E:\RemoteInstall\SMSImages\OSD00002\boot.OSD00002.wim. Will Retry..
Unspecified error (Error: 80004005; Source: Windows)]LOG]!><time="15:20:59.406+300" date="12-19-2013" component="SMSPXE" context="" type="3" thread="2192" file="bootimagemgr.cpp:1180">
I was so fed up, I even tried building a whole new server, and still get the same error messages

Similar Messages

SCCM 2012 SP1 OSD Multicast is failing 0x80004005

I am trying to get multicast to work on a DP. But when I kick off an OSD and get to one of the items that I have enabled multicasting (lets say the OS image) then I get the following in the smsts.log:
Failed to get MCS key (Code 0x80004005)
ClientRequestToMCS::DoRequest failed. error = (0x80004005)
Request to MCS 'MYSCCMSERVER.SCCM.LOCAL' failed with error (Code 0x80004005)
Multicast OpenSessionRequest failed (0x80004005)
Sending status message: SMS_OSDeployment_PackageDownloadMulticastStatusFail
And then it reverts to a normal HTTP download. Why is this failing?

there's a thread here about issues with MCS key though this is 2007 maybe it will point you in a right direction
http://social.technet.microsoft.com/Forums/systemcenter/en-US/07c735c8-9ce9-43b9-8cf3-e7b897568ef3/sccm-multicast-mcs-signedserializedkey-is-empty
The issues I had with multicast came up when the target device was not on the same subnet and network hardware was blocking communication.

Litetouch deployment failed 0x80004005

can not deploy win7 with mdt 2012.
FAILURE ( 5627 ): -1073731515 0xC0000135: Run DISM.exe
Litetouch deployment failed, Return Code = -2147467259 0x80004005
Failed to run the action: Install Operating System.
Unknown error (Error: 000015FB: Source: Unknown)
The execution of the group (Install) has failed and the execution has been aborted.
Operation aborted (Error: 80004004: Source: Windows)
Failed to run the last action: Install Operati ngSystem. Execution of task sequence failed:
Unknown error (Error: 000015FB; Source: Unknown)
Task Sequence Engine failed! Code: enExecutionFail
Task sequence execution failed with error code 80004005
Error Task Sequence Manager failed to execute task swquence. Code 0x80004005
I keep getting this error message and not sure what it could be. Any idea????

The log is very long. Here is the first part of it.
<![LOG[Property LogPath is now = X:\MININT\SMSOSD\OSDLOGS]LOG]!><time="14:34:23.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Microsoft Deployment Toolkit version: 6.1.2373.0]LOG]!><time="14:34:23.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property Debug is now = FALSE]LOG]!><time="14:34:23.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[ZTIUtility!GetAllFixedDrives (False)]LOG]!><time="14:34:23.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[New ZTIDiskPartition : \\MININT-N42LK45\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #0"    \\MININT-N42LK45\root\cimv2:Win32_LogicalDisk.DeviceID="C:"]LOG]!><time="14:34:23.000+000" date="08-16-2013" component="LiteTouch"
context="" type="1" thread="" file="LiteTouch">
<![LOG[New ZTIDisk : \\MININT-N42LK45\root\cimv2:Win32_DiskDrive.DeviceID="\\\\.\\PHYSICALDRIVE0"]LOG]!><time="14:34:23.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[New ZTIDiskPartition : \\MININT-N42LK45\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #1"    \\MININT-N42LK45\root\cimv2:Win32_LogicalDisk.DeviceID="D:"]LOG]!><time="14:34:23.000+000" date="08-16-2013" component="LiteTouch"
context="" type="1" thread="" file="LiteTouch">
<![LOG[New ZTIDisk : \\MININT-N42LK45\root\cimv2:Win32_DiskDrive.DeviceID="\\\\.\\PHYSICALDRIVE0"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[ZTIUtility!GetAllFixedDrives = C: D:]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[No task sequence is in progress.]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[New ZTIDisk : \\MININT-N42LK45\root\cimv2:Win32_DiskDrive.DeviceID="\\\\.\\PHYSICALDRIVE0"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Found Possible OS TargetDisk: \\MININT-N42LK45\root\cimv2:Win32_DiskDrive.DeviceID="\\\\.\\PHYSICALDRIVE0"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[GetPartitions: 2]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Found Possible OS Target Partition: \\MININT-N42LK45\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #0"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[New ZTIDiskPartition : \\MININT-N42LK45\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #0"    \\MININT-N42LK45\root\cimv2:Win32_LogicalDisk.DeviceID="C:"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch"
context="" type="1" thread="" file="LiteTouch">
<![LOG[Target Partition not big enough: \\MININT-N42LK45\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #0"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Found Possible OS Target Partition: \\MININT-N42LK45\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #1"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[New ZTIDiskPartition : \\MININT-N42LK45\root\cimv2:Win32_DiskPartition.DeviceID="Disk #0, Partition #1"    \\MININT-N42LK45\root\cimv2:Win32_LogicalDisk.DeviceID="D:"]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch"
context="" type="1" thread="" file="LiteTouch">
<![LOG[Found Drive: D:]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Found FirstPossibleSystemDrive: D:]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property SMSTSLocalDataDrive is now = D:]LOG]!><time="14:34:24.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property LogPath is now = D:\MININT\SMSOSD\OSDLOGS]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Unable to get Current ID.]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Not running within WinPE or WinRE.]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property DeploymentMethod is now = UNC]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[DeploymentMethod = UNC]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property DeployRoot is now = X:\Deploy]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Using a local or mapped drive, no connection is required.]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[DeployRoot = X:\Deploy]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property DeployDrive is now = X:]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[DeployDrive = X:]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property PHASE is now = PREINSTALL]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property DeploymentType is now = NEWCOMPUTER]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Phase = PREINSTALL]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[About to run command: wscript.exe "X:\Deploy\Scripts\ZTIGather.wsf" /inifile:Bootstrap.ini]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="LiteTouch" context="" type="1" thread="" file="LiteTouch">
<![LOG[Property inifile is now = Bootstrap.ini]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="ZTIGather" context="" type="1" thread="" file="ZTIGather">
<![LOG[Microsoft Deployment Toolkit version: 6.1.2373.0]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="ZTIGather" context="" type="1" thread="" file="ZTIGather">
<![LOG[------------------------- Object Initialization -------------------------]LOG]!><time="14:34:27.000+000" date="08-16-2013" component="ZTIGather" context="" type="1" thread="" file="ZTIGather">
<![LOG[------------------------- Initialization ------------

DllRegisterServer failed - 0x80004005

Having problem with registering the dll bean
It's reporting:
"DllRegisterServer in TestBean failed
Return code was: 0x8000405"
Anyone know why this is happening?
Code listed below:
Using the packager command as:
packager -clsid {D824B185-AE3C-11D6-ABF5-00B0D07B8581} TestBean.jar TestBean
And then:
regsvr32 TestBean.dll
Thanks
Abraham Khalil
public class TestBean {
   int number = -1;
   public TestBean() {
   public TestBean(int number) {
      this.number = number;
   public int getNumber() {
      return number;
   public void setNumber(int number) {
      this.number = number;

I also spent a lot of time on this. Following are the details about fixing this problem. I created 2 batch files, one for setting the environment & the other for running the packager. I run these two batch files one after the other without any problem. I have visual studio installed. Hope this helps. I have a request though, if anyone has a simple working program which calls Java program through a C program, please post it.
Thanks,
Aejaz
----------setenv.bat---------------------------------
set PATH=C:\Program Files\Microsoft SDK\Bin;C:\Program Files\Microsoft Visual Studio\VC98\Bin;C:\Program Files\Microsoft Visual Studio\Common\MSDev98\Bin;C:\j2sdk1.4.2_03\bin;%PATH%
set INCLUDE=C:\Program Files\Microsoft Visual Studio\VC98\Include
set JRE_HOME=C:\Progra~1\Java\j2re1.4.2_03
---------PackagerCmd.bat-------------------------
packager -clsid {D824B185-AE3C-11D6-ABF5-00B0D07B8581} -out C:\Progra~1\Java\j2re1.4.2_03\axbridge\bin -reg PersonBean.jar Person
REM Set JRE_HOME to C:\Progra~1\Java\j2re1.4.2_03
REM Create %JRE_HOME%\axbridge\bin & %JRE_HOME%\axbridge\lib before running
REM above command
REM If the output dir isn't %JRE_HOME%\axbridge\bin the command will fail
REM PersonBean.jar created from the example at
REM http://www.reallyusefulcomputing.com/java/activex/tutorial.php

Litetouch Deployment Failed - 0x80004005 (Install OS Phase Error)

I am trying to install OS Image onto hyperV VM....so far it was working fine...after 1 month I tried again and got this error...
anyone have any idea/solution... please advise.
Thanks!

I guess, Yes it is going to Partition 2..see bold text below from BDD.logs.
Any idea how to fix this shit! By the way, I have tried this image on VMware VM and it was fine throughout. However, When I do this on Hyper V VM - I run into this trouble.
<![LOG[ Console > DISKPART> ]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > Partition ### Type Size Offset]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > ------------- ---------------- ------- -------]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > Partition 1 Primary 499 MB 1024 KB]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > * Partition 2 Primary 64 GB 500 MB]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart"
context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > DISKPART> ]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > Volume ### Ltr Label Fs Type Size Status Info]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart"
context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > ---------- --- ----------- ----- ---------- ------- --------- --------]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart" context="" type="1" thread=""
file="ZTIDiskpart">
<![LOG[ Console > Volume 0 D DVD_ROM UDF DVD-ROM 4149 MB Healthy ]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart"
context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > Volume 1 W System NTFS Partition 499 MB Healthy ]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart"
context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > * Volume 2 C SYSTEM NTFS Partition 64 GB Healthy ]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart"
context="" type="1" thread="" file="ZTIDiskpart">
<![LOG[ Console > DISKPART> ]LOG]!><time="01:34:41.000+000" date="07-02-2014" component="ZTIDiskpart" context="" type="1" thread="" file="ZTIDiskpart">

USMT Errors - Request to SMP failed with error 0x80004005

The client I am at we are working on using USMT integrated with their OSD task sequence. Yesterday we setup a State Migration Point on the DP that is located at this office. We ran a task sequence for testing purposes that just basically does the Scan
State. The few machines we tested this task sequence on successfully completed the task.
This morning we have tried some more testing and now the task doesn't work. The job fails at the point where it is requesting user store space. The log files shows that it knows about the SMP and that it request access but it fails and continues
on trying to find another available SMP.
The first few attempts the errors are based on "Failed to connect to
\\SERVER.DOMAIN\SMPSTORED_241ADE445 (53)
"Cannot connect to http://SERVER.DOMAIN SMP root share"
"Request to SMP 'http://SERVER.DOMAIN' failed with error (Code 0x80004005) Trying next SMP.
"SMP request to 'http://server.domain" failed with error: E_SMPERROR_ENCRYPTKEY_EMPTY (103)
"ClientKeyRequestToSMP failed (0x80004005)
We have removed the SMP and have re-added it.
Kristopher Turner | Not the brightest bulb but by far not the dimmest bulb.

Hi,
See if this thread helps solve the problem
http://social.technet.microsoft.com/Forums/en-US/c3883768-5a49-45bc-b173-5f7eff8eca53/usmt-capture-task-sequence-failing?forum=configmanagerosd
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Post Upgrade to R2: Task Sequence Fails with 0x80070057

one SCCM 2012 server for a while now (June/July of 2013) and have had no issues with OSD's and software deployments. Today I decided to upgrade to R2 from CU3 and I thought the upgrade process went really well. But after the upgrade
I attempted to perform an OSD & it failed with error 0x80070057 before the Task Sequence selection.
I had that problem ages ago when I first started using SCCM, but that was due to a missing boundary group. I got that straightened out in June/July of 2013 and, OSD's & software deployments have been working fine since.
All the boundary groups are still defined
All the boundaries are still defined
The specific boundary this machine is in has a site system defined
The specific boundary group this machine is in has both an assigned site as well as a site system server defined
Verified server has full control over System Management
Verified server has been published in AD
Relevant section of %temp%\smsts\smsts.log in boot environment
Root CA Public Certs= TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Missing root CA environment variable from variables file TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Support Unknown Machines: 1 TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Custom hook from X:\\TSConfig.INI is TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
No hook is found to be executed before downloading policy TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Authenticator from the environment is empty. TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Need to create Authenticator Info using PFX TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Initialized CStringStream object with string: 171D4480-4E88-4DA5-B047-C4DC4E8EF947;2014-03-11T00:55:46Z. TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Using user-defined MP locations: http://SCCMSERVER.F.Q.D.N TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Set authenticator in transport TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Set media certificates in transport TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
IP: 10.1.18.11 10.1.18.0 TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
CLibSMSMessageWinHttpTransport::Send: URL: SCCMSERVER.F.Q.D.N:80 GET /SMS_MP/.sms_aut?MPLOCATION&ir=10.1.18.11&ip=10.1.18.0 TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Error. Status code 500 returned TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
isSuccessful, HRESULT=80004005 (e:\qfe\nts\sms\framework\osdmessaging\libsmsmessaging.cpp,5581) TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
CCM::SMSMessaging::CLibSMSMPLocation::RequestMPLocation failed; 0x80004005 TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
MPLocation.RequestMPLocation (szTrustedRootKey, sIPSubnets.c_str(), sIPAddresses.c_str(), sSiteCode, sAssignedSiteCode, sMP, sMPCertificates, sX86UnknownMachineGUID, sX64UnknownMachineGUID), HRESULT=80004005 (e:\qfe\nts\sms\framework\osdmessaging\libsmsmessaging.cpp,9583) TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
CCM::SMSMessaging::GetMPLocation failed; 0x80004005 TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Failed to query http://SCCMSERVER.F.Q.D.N for MP location TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
New settings: TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
site=,, MP=, ports: http=80,https=443 TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Set authenticator in transport TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
pszSiteCode && pszSiteCode[0], HRESULT=80070057 (e:\qfe\nts\sms\framework\tscore\tspolicy.cpp,580) TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
TS::Policy::GetClientIdentity (&httpTransport, sSiteCode.c_str(), sMediaGuid.c_str(), sClientGUID, sNetbiosName, bUnknown, sServerName, sServerRemoteName, sImportedClientIdentity), HRESULT=80070057 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawizardcontrol.cpp,965) TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Exiting TSMediaWizardControl::GetPolicy. TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
pWelcomePage->m_pTSMediaWizardControl->GetPolicy(), HRESULT=80070057 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawelcomepage.cpp,303) TSMBootstrap 3/10/2014 4:55:46 PM 1124 (0x0464)
Setting wizard error: An error occurred while retrieving policy for this computer (0x80070057). For more information, contact your system administrator or helpdesk operator. TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
WelcomePage::OnWizardNext() TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
Skipping Confirmation Page. TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
Skipping Task Sequence Selection Page. TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
Skipping Variables Selection Page. TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
Skipping Resolve Progress Page. TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
Activating Finish Page. TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
Loading bitmap TSMBootstrap 3/10/2014 4:55:46 PM 1112 (0x0458)
Executing command line: X:\windows\system32\cmd.exe /k TSBootShell 3/10/2014 4:55:59 PM 840 (0x0348)
The command completed successfully. TSBootShell 3/10/2014 4:55:59 PM 840 (0x0348)
<![LOG[Root CA Public Certs=]LOG]!><time="16:55:46.225+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:615">
<![LOG[Missing root CA environment variable from variables file]LOG]!><time="16:55:46.225+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:621">
<![LOG[Support Unknown Machines: 1]LOG]!><time="16:55:46.225+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:632">
<![LOG[Custom hook from X:\\TSConfig.INI is ]LOG]!><time="16:55:46.225+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:675">
<![LOG[No hook is found to be executed before downloading policy]LOG]!><time="16:55:46.225+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:699">
<![LOG[Authenticator from the environment is empty.]LOG]!><time="16:55:46.240+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:838">
<![LOG[Need to create Authenticator Info using PFX]LOG]!><time="16:55:46.240+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:850">
<![LOG[Initialized CStringStream object with string: 171D4480-4E88-4DA5-B047-C4DC4E8EF947;2014-03-11T00:55:46Z.]LOG]!><time="16:55:46.256+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="stringstream.cpp:101">
<![LOG[Using user-defined MP locations: http://SCCMSERVER.F.Q.D.N]LOG]!><time="16:55:46.256+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:911">
<![LOG[Set authenticator in transport]LOG]!><time="16:55:46.256+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="libsmsmessaging.cpp:7751">
<![LOG[Set media certificates in transport]LOG]!><time="16:55:46.271+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="libsmsmessaging.cpp:9558">
<![LOG[IP: 10.1.18.11 10.1.18.0]LOG]!><time="16:55:46.271+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="libsmsmessaging.cpp:9579">
<![LOG[CLibSMSMessageWinHttpTransport::Send: URL: SCCMSERVER.F.Q.D.N:80 GET /SMS_MP/.sms_aut?MPLOCATION&ir=10.1.18.11&ip=10.1.18.0]LOG]!><time="16:55:46.287+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="libsmsmessaging.cpp:8621">
<![LOG[Error. Status code 500 returned]LOG]!><time="16:55:46.349+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="libsmsmessaging.cpp:8984">
<![LOG[isSuccessful, HRESULT=80004005 (e:\qfe\nts\sms\framework\osdmessaging\libsmsmessaging.cpp,5581)]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="libsmsmessaging.cpp:5581">
<![LOG[CCM::SMSMessaging::CLibSMSMPLocation::RequestMPLocation failed; 0x80004005]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="3" thread="1124" file="libsmsmessaging.cpp:5688">
<![LOG[MPLocation.RequestMPLocation (szTrustedRootKey, sIPSubnets.c_str(), sIPAddresses.c_str(), sSiteCode, sAssignedSiteCode, sMP, sMPCertificates, sX86UnknownMachineGUID, sX64UnknownMachineGUID), HRESULT=80004005 (e:\qfe\nts\sms\framework\osdmessaging\libsmsmessaging.cpp,9583)]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="libsmsmessaging.cpp:9583">
<![LOG[CCM::SMSMessaging::GetMPLocation failed; 0x80004005]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="3" thread="1124" file="libsmsmessaging.cpp:9587">
<![LOG[Failed to query http://SCCMSERVER.F.Q.D.N for MP location]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="3" thread="1124" file="tsmbootstraputil.cpp:1544">
<![LOG[New settings:]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:925">
<![LOG[ site=,, MP=, ports: http=80,https=443]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1124" file="tsmediawizardcontrol.cpp:927">
<![LOG[Set authenticator in transport]LOG]!><time="16:55:46.365+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="libsmsmessaging.cpp:7751">
<![LOG[pszSiteCode && pszSiteCode[0], HRESULT=80070057 (e:\qfe\nts\sms\framework\tscore\tspolicy.cpp,580)]LOG]!><time="16:55:46.381+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="tspolicy.cpp:580">
<![LOG[TS::Policy::GetClientIdentity (&httpTransport, sSiteCode.c_str(), sMediaGuid.c_str(), sClientGUID, sNetbiosName, bUnknown, sServerName, sServerRemoteName, sImportedClientIdentity), HRESULT=80070057 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawizardcontrol.cpp,965)]LOG]!><time="16:55:46.381+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="tsmediawizardcontrol.cpp:965">
<![LOG[Exiting TSMediaWizardControl::GetPolicy.]LOG]!><time="16:55:46.381+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="tsmediawizardcontrol.cpp:1378">
<![LOG[pWelcomePage->m_pTSMediaWizardControl->GetPolicy(), HRESULT=80070057 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawelcomepage.cpp,303)]LOG]!><time="16:55:46.381+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1124" file="tsmediawelcomepage.cpp:303">
<![LOG[Setting wizard error: An error occurred while retrieving policy for this computer (0x80070057). For more information, contact your system administrator or helpdesk operator.]LOG]!><time="16:55:46.381+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1112" file="tsmediawizardcontrol.cpp:1547">
<![LOG[WelcomePage::OnWizardNext()]LOG]!><time="16:55:46.381+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1112" file="tsmediawelcomepage.cpp:340">
<![LOG[Skipping Confirmation Page.]LOG]!><time="16:55:46.381+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1112" file="tsmediaconfirmationpage.cpp:170">
<![LOG[Skipping Task Sequence Selection Page.]LOG]!><time="16:55:46.396+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1112" file="tsmediataskselectionpage.cpp:118">
<![LOG[Skipping Variables Selection Page.]LOG]!><time="16:55:46.396+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1112" file="tsmediavariablesselectionpage.cpp:155">
<![LOG[Skipping Resolve Progress Page.]LOG]!><time="16:55:46.396+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1112" file="tsmediaresolveprogresspage.cpp:96">
<![LOG[Activating Finish Page.]LOG]!><time="16:55:46.396+480" date="03-10-2014" component="TSMBootstrap" context="" type="0" thread="1112" file="tsmediafinishpage.cpp:107">
<![LOG[Loading bitmap]LOG]!><time="16:55:46.396+480" date="03-10-2014" component="TSMBootstrap" context="" type="1" thread="1112" file="tsmbootstrap.cpp:1228">
<![LOG[Executing command line: X:\windows\system32\cmd.exe /k]LOG]!><time="16:55:59.048+480" date="03-10-2014" component="TSBootShell" context="" type="1" thread="840" file="bootshell.cpp:857">
<![LOG[The command completed successfully.]LOG]!><time="16:55:59.048+480" date="03-10-2014" component="TSBootShell" context="" type="1" thread="840" file="bootshell.cpp:939">
Could this be an IIS problem?

I've had problems after the R2 upgrade and had to reinstall PXE/WDS on Distribution Point to resolve.
Also ensure that you apply this hotfix after R2:
http://www.deploymentresearch.com/Research/tabid/62/EntryId/156/Do-not-do-OSD-in-ConfigMgr-2012-R2-without-this-hotfix.aspx
Gerry Hampson | Blog:
www.gerryhampsoncm.blogspot.ie | LinkedIn:
Gerry Hampson | Twitter:
@gerryhampson

Distribution Manager Failed To Access The Source Directory

Hello All,
I have this issue distributing content to my Distribution Points for months now. I keep running into this error below:
Distribution Manager Failed to Access the source directory (\\share\folder\file.wim)
Possible Cause: Distribution Manager does not have sufficient rights to the source directory.
Solution: Verify that the site server computer account has at least Read access to the directory you specify as the source directory.
Possible Cause: There is not enough disk space available on the site server.
Solution: Verify that there is enough free disk space available on the site server.
I checked the distmgr.log file and received these messages:
GetTempFileNameA failed; 0x80004005   SMS_DISTRIBUTION_MANAGER   3/24/2015 2:15:38 PM   13952 (0x3680)
CFileLibrary::AddFile failed; 0x80004005   SMS_DISTRIBUTION_MANAGER   3/24/2015 2:15:38 PM   13952 (0x3680)
CContentDefinition::AddFile failed; 0x80004005   SMS_DISTRIBUTION_MANAGER   3/24/2015 2:15:38 PM   13952 (0x3680)
Failed to add the file. Please check if this file exists.   SMS_DISTRIBUTION_MANAGER   3/24/2015 2:15:38 PM   13952 (0x3680)
SnapshotPackage() failed. Error = 0x80004005   SMS_DISTRIBUTION_MANAGER   3/24/2015 2:15:38 PM   13952 (0x3680)
Failed to take snapshot of package CSU0006A   SMS_DISTRIBUTION_MANAGER   3/24/2015 2:15:38 PM   13952 (0x3680)
There is enough space on the site server and the site server has full control over the source directory. I wish I can give you more information but I'm hoping this is enough info to get some assistance. If more information is needed please let me know!

We usually give the DP's computer account and the site server computer account read access to these shares in our environment.
... which is not enough for drivers and updates (as there will also files be added).
Torsten Meringer | http://www.mssccmfaq.de
... And for capture Image too if your capture destination points on that share

Exchange 2007 2010 coexist autodiscover fails

We are migrating from 2007 to 2010. Autodiscover is not working on the 2010 CAS servers (4 of them).
SMTP=[email protected]
Attempting URL
https://autodiscover.domain.com/Autodiscover/Autodiscover.xml found through SCP
Autodiscover to
https://autodiscover.domain.com/Autodiscover/Autodiscover.xml starting
GetLastError=o; httpStatus=500
Autodiscover request completed with http status code 500
Autodiscover to
https://autodiscover.domain.com/Autodiscover/Autodiscover.xml Failed (0x80004005)
If I browse to the page, it returns the normal XML - error 600 Invalid request page.
The AutoDiscoverServiceInternalUri is set to
https://autodiscover.newpagecorp.com/Autodiscover/Autodiscover.xml on both the 2007 and 2010 CAS servers.
If we point our autodiscover DNS record to the 2007 CAS servers, 2007 mail users function just fine. If we point it to 2010 CAS servers, autodiscover fails, for both 2007 mail users and 2010 mail users (we only have 3 test users migrated)
Please help!
Thank you!

Just noticed this in the event log:
Log Name:      Application
Source:        System.ServiceModel 3.0.0.0
Date:          4/24/2014 7:06:02 PM
Event ID:      3
Task Category: WebHost
Level:         Error
Keywords:      Classic
User:          SYSTEM
Computer:      server.domain.com
Description:
WebHost failed to process a request.
Sender Information: System.ServiceModel.ServiceHostingEnvironment+HostingManager/32001227
Exception: System.ServiceModel.ServiceActivationException: The service '/Autodiscover/autodiscover.xml' cannot be activated due to an exception during compilation. The exception message is: A binding instance has already been associated to listen
URI 'http://server.domain.com/Autodiscover/Autodiscover.xml'. If two endpoints want to share the same ListenUri, they must also share the same binding object instance. The two conflicting endpoints were either specified in AddServiceEndpoint() calls, in a
config file, or a combination of AddServiceEndpoint() and config. . ---> System.InvalidOperationException: A binding instance has already been associated to listen URI 'http://server.domain.com/Autodiscover/Autodiscover.xml'. If two endpoints want to share
the same ListenUri, they must also share the same binding object instance. The two conflicting endpoints were either specified in AddServiceEndpoint() calls, in a config file, or a combination of AddServiceEndpoint() and config.
   at System.ServiceModel.Description.DispatcherBuilder.InitializeServiceHost(ServiceDescription description, ServiceHostBase serviceHost)
   at System.ServiceModel.ServiceHostBase.InitializeRuntime()
   at System.ServiceModel.ServiceHostBase.OnOpen(TimeSpan timeout)
   at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.ActivateService(String normalizedVirtualPath)
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath)
   --- End of inner exception stack trace ---
   at System.ServiceModel.ServiceHostingEnvironment.HostingManager.EnsureServiceAvailable(String normalizedVirtualPath)
   at System.ServiceModel.ServiceHostingEnvironment.EnsureServiceAvailableFast(String relativeVirtualPath)
Process Name: w3wp
Process ID: 8256

PXE fails to boot

I have been trying to get SCCM 2012 installed on our network for over a month now and I have no status errors whats so ever but when ever I PXE boot the SMSPXE.log file shows these errors.
I have googled these errors but everything I find is not releated to my setup i.e. Not using HTTPS but HTTP.
Thanks in advance for any help you can offer.
SMSPXE.log
reply has no message header marker SMSPXE
10/12/2013 14:20:04 2452 (0x0994)
PXE::MP_LookupDevice failed; 0x80004005 SMSPXE
10/12/2013 14:20:04 2452 (0x0994)
reply has no message header marker SMSPXE
10/12/2013 14:20:04 2452 (0x0994)
Failed to send status message (80004005) SMSPXE
10/12/2013 14:20:04 2452 (0x0994)
Failed to send the status message SMSPXE
10/12/2013 14:20:04 2452 (0x0994)
PXE::MP_ReportStatus failed; 0x80004005 SMSPXE
10/12/2013 14:20:04 2452 (0x0994)
PXE Provider failed to process message.
Unspecified error (Error: 80004005; Source: Windows)
SMSPXE 10/12/2013 14:20:04
2452 (0x0994)
00:50:56:A8:14:3B, F19F2842-E02C-41BC-C663-5F37CA7ADE5C: Not serviced.
SMSPXE 10/12/2013 14:20:04
2452 (0x0994)

Okay so I have re installed the MP and ran a script to clear up the WMI (Get-WMIObject -namespace "root" -query "SELECT * FROM __Namespace where name = 'ccm'" | remove-wmiobject) and now my MP is working. Also I changed a domain policy that set NT Authority\INTERACTIVE
to read only which seemed to break my MP when the policy updated. I can now PXE boot but after I put my password in I know get an error msg.
I have obtained the logs from the clients attempt to run the task sequence and I get the following.
Downloading policy from http://MCA-VSCCM.MCA.INTERNAL.
TSPxe
16/12/2013 14:04:03
700 (0x02BC)
Initializing HTTP transport. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Setting URL = http://MCA-VSCCM.MCA.INTERNAL.
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
Setting Ports = 80,443. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Setting CRL = false. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Setting Server Certificates. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Set authenticator in transport TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Setting Media Certificate. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Preparing Client Identity Request. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Setting transport. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Setting SourceID = {342F6C35-C40F-4AD9-8FE8-9C214C5D749E}.
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
Setting site code = P01. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
Can not find DeploymentType in file TsmBootstrap.ini or the file doesn't exist. This is not running on Windows To Go.
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
spLocator.createInstance( ((bUseAdminLocator == true) ? CLSID_WbemAdministrativeLocator : CLSID_WbemLocator ) ), HRESULT=80040154 (e:\nts_sccm_release\sms\framework\core\ccmcore\wminamespace.cpp,264)
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
Could not create WMI locator class (80040154)
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
spNamespace.Open(c_szCIMv2Namespace), HRESULT=80040154 (e:\qfe\nts\sms\framework\tscore\tspolicy.cpp,604)
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
Failed to connect to WMI namespace \\.\ROOT\CIMV2 (Code 0x80040154)
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
TS::Policy::GetClientIdentity (&m_oHttpTransport, m_sSiteCode, sMediaGuid.c_str(), m_sClientGUID, m_sNetbiosName, bUnknown, sServerNames, sImportedClientIdentity), HRESULT=80040154 (e:\qfe\nts\sms\framework\tscore\tspolicy.cpp,867)
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
m_pPolicyManager->init( sMP, nHttpPort, nHttpsPort, sSiteCode, bUseCRL, L"", sMediaPfx, sMediaGuid, sEnterpriseCert, sServerCerts, sSiteSigningCert, sAuthenticator), HRESULT=80040154 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawizardcontrol.cpp,1239)
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
Exiting TSMediaWizardControl::GetPolicy. TSPxe
16/12/2013 14:04:03 700 (0x02BC)
pWelcomePage->m_pTSMediaWizardControl->GetPolicy(), HRESULT=80040154 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawelcomepage.cpp,303)
TSPxe 16/12/2013 14:04:03
700 (0x02BC)
Setting wizard error: An error occurred while retrieving policy for this computer (0x80040154). For more information, contact your system administrator or helpdesk operator.
TSPxe 16/12/2013 14:04:03
692 (0x02B4)
WelcomePage::OnWizardNext() TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Skipping Confirmation Page. TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Skipping Task Sequence Selection Page. TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Skipping Variables Selection Page. TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Skipping Resolve Progress Page. TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Activating Finish Page. TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Initializing the countdown timer. TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Loading bitmap TSPxe
16/12/2013 14:04:03 692 (0x02B4)
Fell so close to getting this working but not sure what the final step is..

Request User State Store Fails with error code 0x00004005

I am trying to get a machine refresh working in SCCM and am running into a road block with the user state migration. The Task sequence hits Request user state store and then fails. In the logs on the machine it shows it downloads the cert from the SMP but it fails to verify the cert. The thing is that this was working and then stopped for no apparent reason. I have added a second SMP and it has the same issue so its got to be something environmental causing this. I have found no references to the errors I am recieving that relate to the issue so I am stumped. We have a SCCM 2007 site in mixed mode. The error log is:
The task sequence execution engine failed executing the action (Request User State Storage) in the group (Capture User Files and Settings) with the error code 16389 Action output: ployment\osdsmpclient\smpclient.cpp,1743) Request to SMP 'ATXFREPSMS01.NA.atxglobal.com' failed with error (Code 0x80090006). Trying next SMP. FALSE, HRESULT=80004005 (e:\nts_sms_fre\sms\client\osdeployment\osdsmpclient\smpclient.cpp,1698) pClientRequestToSMP->Execute(migInfoFromMP.saSMPs), HRESULT=80004005 (e:\nts_sms_fre\sms\client\osdeployment\osdsmpclient\smpclient.cpp,2713) ExecuteCaptureRequestToSMP(migInfoFromMP), HRESULT=80004005 (e:\nts_sms_fre\sms\client\osdeployment\osdsmpclient\smpclient.cpp,2755) ExecuteCaptureRequest(), HRESULT=80004005 (e:\nts_sms_fre\sms\client\osdeployment\osdsmpclient\main.cpp,72) OSDSMPClient finished: 0x00004005 Failed to verify certificate signature for 'ATXFREPSMS01.NA.atxglobal.com' (0x80090006) ClientKeyRequestToSMP failed (0x80090006). ClientRequestToSMP:oRequest failed. error = (0x80090006). Failed to find an SMP that can serve request after trying 4 attempts. ExecuteCaptureRequestSMP failed (0x80004005). ExecuteCaptureRequest failed (0x80004005).. The operating system reported error 16389:

Hi
I am getting the same issue.
More info:
The same task works ok for one client - an xp machine that was upgraded to vista sp1 using sccm but without usmt.
If I send this machine a task which includes usmt and os deploy it works.
On 2 other machines ( so far) , the request store fails with the same error - 0x80090006. (one of them existing vista and the other xp)
I have tried removing and adding the client from the domain but it did not help.
Any idea?
David

Task Sequence failed to restore captured data from USB drive onto a new machine using UDI task requence

Hi,
Environment ConfigMgr 2012 R2
Replace Scenario: Capture data to a USB external drive and Restore it from USB external drive.
Steps taken:
1) Created Computer Association with New computer and Source computer
2) Deployed UDI replace Task Sequence to Source computer and captured data to a USB external drive
3) Run UDI Task Sequence from Boot Media to Restore data from USB External drive which had the captured data.
Issue:
My task sequence failed to restore data from USB external drive.
Is there a fix
Any help is greatly appreciated it.

I created a query to see the deployment logs in real time. I see the TS fails when running "Request State Store" task. Here are the logs.
Severity Type Site code Date / Time System Component Message ID Description
Error Milestone POK 7/22/2014 4:13:15 PM MININT-P6E4T6G Task Sequence Engine 11141 The task sequence execution engine failed execution of a task sequence. The operating system reported error 1: Incorrect function.
Error Milestone POK 7/22/2014 4:13:15 PM MININT-P6E4T6G Task Sequence Engine 11135 The task sequence execution engine failed executing the action (Error in the task sequence) in the group (Gather Logs and StateStore on Failure)
with the error code 1 Action output: [ smsswd.exe ] PackageID = '' BaseVar = '', ContinueOnError='' ProgramName = 'cscript "C:\_SMSTaskSequence\WDPackage\scripts\ztierrormsg.wsf"' SwdAction = '0001' Set command line: Run command line Working dir 'not
set' Executing command line: Run command line Process completed with exit code 1 Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. Microsoft Deployment Toolkit version: 6.2.5019.0 The task sequencer
log is located at C:\WINDOWS\CCM\Logs\SMSTSLog\SMSTS.LOG. For task sequence failures, please consult this log. ZTI deployment failed, Return Code = 1 Command line returned 1. The operating system reported error 1: Incorrect function.
Information Milestone POK 7/22/2014 4:13:14 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Copy Logs) in the group (Gather Logs and StateStore on Failure)
with exit code 0 Action output: ... 扴捡杫潲湵⹤潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌獧䍜剏ⵐ䠳䑗塐就瑺獩瑥慢正牧畯摮氮杯潃祰湩⁧㩃坜义佄南䍜䵃䱜杯屳䵓呓䱓杯穜楴慴潴⹯潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散�潌獧䍜剏ⵐ䠳䑗塐就潃祰湩⁧㩃坜义佄南䍜䵃䱜杯屳䵓呓䱓杯作䑓敓畴坰穩牡⹤潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌獧䍜剏ⵐ䠳䑗塐就协卄瑥灵楗慺摲氮杯潃祰湩⁧㩃坜义佄南停湡桴�潬⁧潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌獧䍜剏ⵐ䠳䑗塐就慐瑮敨屲湕瑡整摮䍇潃祰湩⁧潬⁧㩃坜义佄南䍜䵃䱜杯屳䵓呓䱓杯䉜䑄氮杯挠湯整瑮⁳潴尠停䭏偃䍓䵃卐㄰䍜彍潓牵散尤协屄潌�Console
> Successfully resized the shadow copy storage association Return code from command = 0 Cleaning up default wallpaper registry keys Process completed with exit code 0 zticopylogs processing completed successfully. Command line returned 0.
Information Milestone POK 7/22/2014 4:13:07 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Move State Store) in the group (Gather Logs and StateStore on Failure)
with exit code 0 Action output: [ smsswd.exe ] PackageID = '' BaseVar = '', ContinueOnError='' ProgramName = 'cscript.exe "C:\_SMSTaskSequence\WDPackage\scripts\ztimovestatestore.wsf"' SwdAction = '0001' Command line for extension .exe is "%1" %* Set
command line: Run command lineWorking dir 'not set' Executing command line: Run command line Process completed with exit code 0 Microsoft (R) Windows Script Host Version 5.8 Copyright (C) Microsoft Corporation. All rights reserved. Microsoft Deployment
Toolkit version: 6.2.5019.0 The task sequencer log is located at C:\WINDOWS\CCM\Logs\SMSTSLog\SMSTS.LOG. For task sequence failures, please consult this log. ztimovestatestore processing completed successfully. Command line returned 0.
Information Milestone POK 7/22/2014 4:13:07 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Gather) in the group (Gather Logs and StateStore on Failure) with
exit code 0 Action output: ... (BIOS is 'DELL - 1072009'). Property IsVM is now = False Finished getting virtualization info Connection succeeded to MicrosoftVolumeEncryption There are no encrypted drives Property IsBDE is now = False Processing
the phase. Determining theINI file to use. Using COMMAND LINE ARG: Ini file = CustomSettings.ini Finished determining the INI file to use. Added new custom property MYCUSTOMPROPERTY Using from [Settings]: Rule Priority = DEFAULT ------ Processing the
[DEFAULT] section ------Process completed with exit code 0 ------ Done processing CustomSettings.ini ------ Remapping variables. Property TaskSequenceID is now = Property DeploymentType is now = NEWCOMPUTER Finished remapping variables. ZTIGather processing
completed successfully. Command line returned 0 ReleaseSource() for C:\_SMSTaskSequence\Packages\POK0000F. reference count 1 for the source C:\_SMSTaskSequence\Packages\POK0000F before releasing Released the resolved source C:\_SMSTaskSequence\Packages\POK0000F.
Information Milestone POK 7/22/2014 4:13:03 PM MININT-P6E4T6G Task Sequence Engine 11130 The task sequence execution engine skipped the action (Use Toolkit Package) in the group (Gather Logs and StateStore on Failure) because
the condition was evaluated to be false.
Information Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11134 The task sequence execution engine successfully completed the action (Set Error Code) in the group (Gather Logs and StateStore on Failure)
with exit code 0 Action output: Finished with error code 0.
Information Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11124 The task sequence execution engine started the group (Gather Logs and StateStore on Failure).
Information Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11122 The task sequence execution engine skipped the group (Cancelled Wizard Group) because the condition was evaluated to be false.
Error Milestone POK 7/22/2014 4:13:02 PM MININT-P6E4T6G Task Sequence Engine 11135 The task sequence execution engine failed executing the action (Connect to State Store) in the group (State Restore) with the error code 1
Action output: ... ( 0x80070035 ) , trying to connect without username. The network path was not found. Unable to connect to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Sleeping for 15 seconds. Unable to connect to share: The network path was notfound. ( 0x80070035 ) , trying to
connect without username. The network path was not found. Unable to connect to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Sleeping for 20 seconds. Unable to connect to share: The network path wasnot found. ( 0x80070035 ) , trying to
connect without username. The network path was not found. Unable to connect to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Sleeping for 25 seconds. Process completed with exit code 1 ERROR - Unable to map a network drive to
\\3807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f. Unable to connect to 563807000000100000000000:\2fa390ff58558b49c45bf204dfa5717f ZTI ERROR - Non-zero return code by ZTIConnect,
rc = 1 Command line returned 1. The operating system reported error 1: Incorrect function.
Warning Milestone POK 7/22/2014 4:11:46 PM MININT-P6E4T6G Task Sequence Engine 11138 The task sequence execution engine ignored execution failure of the action (Request State Store) in the group (State Restore).
Error Milestone POK 7/22/2014 4:11:46 PM MININT-P6E4T6G Task Sequence Engine 11135 The task sequence execution engine failed executing the action (Request State Store) in the group (State Restore) with the error code 16389
Action output: ... etting Media Certificate. Sending request to MP
http://abcdefg.xyx.xyz.local. Setting message signatures. Setting the authenticator. CLibSMSMessageWinHttpTransport::Send: URL: abcdefg.xyx.xyz.local:80 CCM_POST /ccm_system/requestRequest was successful. migInfoRequestMessage.DoRequest (m_sResponse,true),
HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\smpclient.cpp,1098) pClientRequestToMP->DoRequest(), HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\smpclient.cpp,2778) ExecuteRestoreRequestToMP(migInfoFromMP),
HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\smpclient.cpp,2903) ExecuteRestoreRequest(), HRESULT=80004005 (e:\nts_sccm_release\sms\client\osdeployment\osdsmpclient\main.cpp,84) OSDSMPClient finished: 0x00004005 reply from server
is 'NoReply' ClientRequestToMP::DoRequest failed (0x80004005). ExecuteRestoreRequestToMP failed (0x80004005). ExecuteRestoreRequest failed (0x80004005).. The operating system reported error 1: Incorrect function.

Autodiscover fails in Ex2010/Ex2013 co-existence

Dear readers,
Currently we are in the preparation phase of the migration from Exchange 2010 to Exchange 2013. I have followed the Exchange Deployment Assistant, but unfortunately it does not work as expected.
I think i might have created an autodiscover loop and I don’t know how to fix it. Our setup
2x 2010CAS 192.168.2.10, 192.168.2.11
2x 2010MBX 192.168.2.20, 192.168.2.21 (DAG01)
2x 2013CAS 192.168.2.110, 192.168.2.111
2x 2013MBX 192.168.2.120, 192.168.2.121 (DAG02)
autodiscover.ourextdomain.com for internal clients point to 192.168.2.110
webmail.ourextdomain.com for internal clients point to 192.168.2.110
For now company policy does not allow making the Exchange services available externally. So all the clients only connect internally (on the corporate network or using VPN), also webmail is only accessible internally.
On all the CAS servers (meaning both 2010 and 2013) I have set the internal and external URL for every service (EWS, ECP, OWA, OAB, ActiveSync, Autodiscover, Outlook Any Where) to point to the same external domain: webmail.ourextdomain.com and autodiscover.ourextdomain.com.
(This is how I interpreted it from the Exchange Deployment Assistant).
If an internal Outlook 2010 user tries to use autodiscover to connect to his mbx on 2010, he gets httpstatus 401 and 401 errors and autodiscover to <url> failed 0x80004005, 0x800C8203 and is unable to successfully connect. An outlook 2010 user with a
2013 mbx can connect successfully.
If I change autodiscover.ourextdomain.com to point to 192.168.2.10, it is the other way around. The outlook 2010 user with 2010 mbx can connect, but the outlook 2010 user with 2013 mbx cannot.
My guess is that the configuration for the internal and external URLs is not correct, but I am not sure how to fix this. Does anyone have an idea? We have a third part wildcard certificate which I installed on all the CAS servers. This gave certificate errors
at first, for some reason clients were still trying to connect to a .local server address. This seems to be fixed after I re-created the Autodiscover vdirs.
As we have had a lot of issues with the certificate (a lot of calls at the service desk) I am a little less enthusiastic about
changing the internal and external URLs again, until I am a little more certain it is the right change to make.
Maybe useful info:
- Exchange 2010 did not have Outlook Anywhere enabled until I started following the Exchange deployment assistant
- Exchange 2010 has been an upgrade from Exchange 2003 (there are no Exchange 2003 servers anymore, as than I would not be able
to start the 2013 installation at all).
- Running Exchange 2010 SP3 ur7, migrating to Exchange 2013 cu6
Anyone any ideas or pointers in the right direction?

Hi,
1.What about configuring outlook 2010 manually for exchange 2010 mailbox users instead of using the auto discover service ? Just tell me whether it will get succeed or not ?
I really hope you mean for just one user to test it, because we are not going to manually reconfigure outlook for 3500 users! If i manually configure one user it succeeds, if I create a new profile using auto discover where exchange 2013 is the
CAS it fails if Exchange 2010 is the CAS is works.
2.Did you have the cas array configured on exchange 2010 ?If so what is the rpc client access attribute value for all the exchange 2010 databases?
Exchange 2010 DB's:
RpcClientAccessServer : cas.ourintdomain.local
Exchange 2013 DB's
RpcClientAccessServer : cas.ourintdomain.local
3.Please run the below mentioned command on exchange 2010 / 2013 cas servers and also share me the output.
get-ClientAccessServer -Identity CASServer | fl *internal*
https://autodiscover.ourextdomain.com/Autodiscover/Autodiscover.xml
4.make sure the names utilized in your environments are available on the SAN certificate .Most importantly we need to check the certificate is enabled for both exchange 2010 and 2013 services like pop,imap,iis,smtp and also certificate status should have to
be valid.
Get-ExchangeCertificate -Server "ClientAccess2010" | fl
EXCHANGE 2010 CAS O1
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAccessR
ule, System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAcc
essRule}
CertificateDomains : {EX2010CAS01, EX2010CAS01.ourintdomain.local}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=DEX2010CAS01
NotAfter : 7/28/2019 12:33:20 PM
NotBefore : 7/28/2014 12:33:20 PM
PublicKeySize : 2048
RootCAType : None
SerialNumber : [intentionally removed]
Services : IMAP, POP, SMTP
Status : Valid
Subject : CN=EX2010CAS01
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAccessR
ule, System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {*.ourextdomain.com, ourextdomain.com}
HasPrivateKey : True
IsSelfSigned : False
Issuer : CN=GlobalSign Domain Validation CA - G2, O=GlobalSign nv-sa, C=BE
NotAfter : 12/18/2018 12:06:29 PM
NotBefore : 2/19/2014 9:52:02 AM
PublicKeySize : 2048
RootCAType : ThirdParty
SerialNumber : [intentionally removed]
Services : IIS, SMTP
Status : Valid
Subject : CN=*.ourextdomain.com, OU=Domain Control Validated
Thumbprint : [intentionally removed]
EXCHANGE 2010 CAS O2
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAccessR
ule, System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAcc
essRule}
CertificateDomains : {EX2010CAS02, EX2010CAS02.ourintdomain.local}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=DEX2010CAS02
NotAfter : 7/28/2019 12:33:20 PM
NotBefore : 7/28/2014 12:33:20 PM
PublicKeySize : 2048
RootCAType : None
SerialNumber : [intentionally removed]
Services : IMAP, POP, SMTP
Status : Valid
Subject : CN=EX2010CAS02
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule, System.Security.AccessControl.CryptoKeyAccessR
ule, System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {*.ourextdomain.com, ourextdomain.com}
HasPrivateKey : True
IsSelfSigned : False
Issuer : CN=GlobalSign Domain Validation CA - G2, O=GlobalSign nv-sa, C=BE
NotAfter : 12/18/2018 12:06:29 PM
NotBefore : 2/19/2014 9:52:02 AM
PublicKeySize : 2048
RootCAType : ThirdParty
SerialNumber : [intentionally removed]
Services : IIS, SMTP
Status : Valid
Subject : CN=*.ourextdomain.com, OU=Domain Control Validated
Thumbprint : [intentionally removed]
EXCHANGE 2013 CAS O1
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {EX2013CAS01, EX2013CAS01.ourintdomain.local}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=EX2013CAS01
NotAfter : 11/20/2019 5:42:31 PM
NotBefore : 11/20/2014 5:42:31 PM
PublicKeySize : 2048
RootCAType : Registry
SerialNumber : [intentionally removed]
Services : IMAP, POP, SMTP
Status : Valid
Subject : CN=EX2013CAS01
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {WMSvc-EX2013CAS01}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=WMSvc-EX2013CAS01
NotAfter : 11/17/2024 4:03:29 PM
NotBefore : 11/20/2014 4:03:29 PM
PublicKeySize : 2048
RootCAType : Registry
SerialNumber : [intentionally removed]
Services : None
Status : Valid
Subject : CN=WMSvc-EX2013CAS01
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=Microsoft Exchange Server Auth Certificate
NotAfter : 10/23/2019 7:05:50 PM
NotBefore : 11/18/2014 6:05:50 PM
PublicKeySize : 2048
RootCAType : None
SerialNumber : [intentionally removed]
Services : SMTP
Status : Valid
Subject : CN=Microsoft Exchange Server Auth Certificate
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {*.ourextdomain.com, ourextdomain.com}
HasPrivateKey : True
IsSelfSigned : False
Issuer : CN=GlobalSign Domain Validation CA - G2, O=GlobalSign nv-sa, C=BE
NotAfter : 12/18/2018 12:06:29 PM
NotBefore : 2/19/2014 9:52:02 AM
PublicKeySize : 2048
RootCAType : ThirdParty
SerialNumber : [intentionally removed]
Services : IIS, SMTP
Status : Valid
Subject : CN=*.ourextdomain.com, OU=Domain Control Validated
Thumbprint : [intentionally removed]
EXCHANGE 2013 CAS O2
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {EX2013CAS02, EX2013CAS02.ourintdomain.local}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=EX2013CAS02
NotAfter : 11/20/2019 5:42:31 PM
NotBefore : 11/20/2014 5:42:31 PM
PublicKeySize : 2048
RootCAType : Registry
SerialNumber : [intentionally removed]
Services : IMAP, POP, SMTP
Status : Valid
Subject : CN=EX2013CAS02
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {WMSvc-EX2013CAS02}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=WMSvc-EX2013CAS02
NotAfter : 11/17/2024 4:03:29 PM
NotBefore : 11/20/2014 4:03:29 PM
PublicKeySize : 2048
RootCAType : Registry
SerialNumber : [intentionally removed]
Services : None
Status : Valid
Subject : CN=WMSvc-EX2013CAS02
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {}
HasPrivateKey : True
IsSelfSigned : True
Issuer : CN=Microsoft Exchange Server Auth Certificate
NotAfter : 10/23/2019 7:05:50 PM
NotBefore : 11/18/2014 6:05:50 PM
PublicKeySize : 2048
RootCAType : None
SerialNumber : [intentionally removed]
Services : SMTP
Status : Valid
Subject : CN=Microsoft Exchange Server Auth Certificate
Thumbprint : [intentionally removed]
AccessRules : {System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule,
System.Security.AccessControl.CryptoKeyAccessRule}
CertificateDomains : {*.ourextdomain.com, ourextdomain.com}
HasPrivateKey : True
IsSelfSigned : False
Issuer : CN=GlobalSign Domain Validation CA - G2, O=GlobalSign nv-sa, C=BE
NotAfter : 12/18/2018 12:06:29 PM
NotBefore : 2/19/2014 9:52:02 AM
PublicKeySize : 2048
RootCAType : ThirdParty
SerialNumber : [intentionally removed]
Services : IIS, SMTP
Status : Valid
Subject : CN=*.ourextdomain.com, OU=Domain Control Validated
Thumbprint : [intentionally removed]
We are using a 3rd party wildcard certificate for all our CAS servers *.ourextdomain.com

DP's have Warning "Failed to retrieve the package list on the distribution point" - How to Clear it?

All but one of my DP's (A new one I just created) have this Warning Message: "Failed to retrieve the package list on the distribution point". They all seem to be working, I can update and push new content to them.
When I go to the smsdpmon.log, it has an error for a package, but I've since redistributed it, and it is working fine. (Items below are snips from the smsdpmon.log)
CContentDefinition::LibraryPackagesWmi: The package data in WMI is not consistent to PkgLib SMS_Distribution_Point_Monitoring 11/16/2013 6:00:01 PM 3920 (0x0F50)
CContentDefinition::LibraryPackagesWmi: Package PS10011B can't be found in PkgLib SMS_Distribution_Point_Monitoring 11/16/2013 6:00:01 PM 3920 (0x0F50)
CContentDefinition::LibraryPackagesWmi failed; 0x80004005 SMS_Distribution_Point_Monitoring 11/16/2013 6:00:01 PM 3920 (0x0F50)
Failed to evaluate package PS10011B, Error code 0x80070002 SMS_Distribution_Point_Monitoring 11/16/2013 6:29:50 PM 3920 (0x0F50)
Since then, after redistributing the package, it clears up the logs... but not the warning in Monitoring:
Start to evaluate package share for package 'PS10011B' version 0 ... SMS_Distribution_Point_Monitoring 11/18/2013 12:39:52 PM 868 (0x0364)
Package PS10011B is verified successfully SMS_Distribution_Point_Monitoring 11/18/2013 12:39:52 PM 868 (0x0364)
So since everything appears to be working fine, how do I clear out that Warning, so I have nice Green Check Mark Icons in my Monitoring Tab, so when something actually does go wrong, I won't just ignore it since it's always been set to Warning?

I'll have to review this. The script
here, alone did not solve the my issue. Interesting that it say I do not have any inconsistencies on any my DP's now, but I run the other one on a single DP, it states I have inconsistencies still.
$WMIPkgList = Get-WmiObject -Namespace Root\SCCMDP -Class SMS_PackagesInContLib | Select -ExpandProperty PackageID | Sort-Object
$ContentLib = (Get-ItemProperty HKLM:SOFTWARE\Microsoft\SMS\DP).ContentLibraryPath
$PkgLibPath = ($ContentLib) + "\PkgLib"
$PkgLibList = (Get-ChildItem $PkgLibPath | Select -ExpandProperty Name | Sort-Object)
$PkgLibList = ($PKgLibList | ForEach-Object {$_.replace(".INI","")})
$PksinWMIButNotContentLib = Compare-Object -ReferenceObject $WMIPkgList -DifferenceObject $PKgLibList -PassThru
##### section 1 #######################
Write-Host Items in WMI but not the Content Library
Write-Host ========================================
$PksinWMIButNotContentLib
Foreach ($Pkg in $PksinWMIButNotContentLib){
Get-WmiObject -Namespace Root\SCCMDP -Class SMS_PackagesInContLib -Filter "PackageID = '$Pkg'" | Remove-WmiObject -Confirm
I wonder if the first script is not looking for INI's whereas the second one is. I verified that the INI's do exist...
I'll run the second on all of my DP's, remove the left over INI's, and report back again next week on status.
-Tony

OSD failed from secondary site

hi
in my environment I have a primary and a secondary server ,pxe role and WDS enabled on both location ,osd is working fine
as for a test we have shutdown the primary server and tried OSD from Secondary site location we have found boot image was not loading and got error showing BCD error why this is happening even though images we available on secondary dp ,while looking smspxe
.log found below error in secondary ,after bringing up primary osd working fine
PXE::MP_LookupDevice failed; 0x80004005 SMSPXE 7/18/2014 1:02:36 PM 3996 (0x0F9C)
reply has no message header marker SMSPXE 7/18/2014 1:02:57 PM 3992 (0x0F98)
Failed to send status message (80004005) SMSPXE 7/18/2014 1:02:57 PM 3992 (0x0F98)
Failed to send the status message SMSPXE 7/18/2014 1:02:57 PM 3992 (0x0F98)
ankith

That's default. Secondaries cannot operate autonomous.
Torsten Meringer | http://www.mssccmfaq.de

InstallBootFilesForImage failed 0x80004005

Similar Messages

Maybe you are looking for